autocad 2008 autocad lt 2008 no experience required - phần 6 pot

... following widths: 2&apos ;-0 ", 2&apos ; -6 ", 3&apos ;-0 ", and 3&apos ; -6 ". Chapter 9 • Using Dynamic Blocks and Tables 364 265 31ch09.qxd 3/30/07 6: 11 PM Page 364 Note the small exclamation ... Osnap, and then at the Specify action loca- tion or [Multiplier/Offset]: prompt, click to place the light- ning-bolt action symbol just above the door. 6. Click th...

Ngày tải lên: 08/08/2014, 23:21

... performed a typi- cal installation of AutoCAD, the file should be in the C:\Program Files \AutoCAD 2008\ UserDataCache\Support folder. LT users should substitute AutoCAD LT 2008 for AutoCAD 2008 in the ... Gradients442 265 31ch11.qxd 3/30/07 6: 14 PM Page 442 5. Place the cursor on the new swatch of AR-RROOF, right-click, and choose Properties. The Tool Properties dialog box...

Ngày tải lên: 08/08/2014, 23:21

... true north of 30° and 30 minutes is shown as N30d30'E in AutoCAD notation. With the surveyor’s unit system, a sloping line that has an up-and-to-the-left direction has a down-and-to-the-right ... a line near the upper-right corner of the grid. 10. Be sure Snap is turned off. Then, enter the following: @140 < n90dw↵ @90 < s42d30'w↵ @140 < s67d30'e↵ @80 < n52d49&apo...

Ngày tải lên: 08/08/2014, 23:21

... drawing. Using the Drop-Down Menus 13 265 31ch01.qxd 3/30/07 4:59 PM Page 13 AUTOCAD ® 2008 AND AUTOCAD LT ® 2008 NO EXPERIENCE REQUIRED ™ David Frey Jon McFarland Wiley Publishing, Inc. 265 31fm.qxd 4/3/07 ... 75 0-8 400, fax (978) 64 6- 8 60 0. Requests to the Publisher for per- mission should be addressed to the Legal Department, Wiley Publishing, Inc., 10475 Crosspo...

Ngày tải lên: 08/08/2014, 23:20

... decimal degrees. For example, you enter an angle of 1 26 35'10" as 1 26. 5 86 or 126d35'10", and it displays as 1 26. 5 861 . AutoCAD uses a d instead of the traditional degree symbol ... example, 2&apos ; -6 1 ⁄2". For this distance, enter 2' 6- 1 /2 or 2&apos ;6. 5. For the most part, these are the units you’ll use in this book. Chapter 3 • Setting Up a D...

Ngày tải lên: 08/08/2014, 23:20

... as you did in Chap- ter 3. Turn off the Grid and Snap. Offset three of the lines 6& apos; to the outside to make the sidewalk. 20' 260 ' 20' 20' 60 ' 60 ' 10' 25' 40' R 16& apos; 20' 30' 10' 6& apos; 170' 20' 15' 20' 4' If ... few inches to the right of the wall, not touching any lines. Then, offset Cons...

Ngày tải lên: 08/08/2014, 23:20

... Figure 6. 34). Now you need to mirror these two diagonal lines to the right side of the roof. Chapter 6 • Using Layers to Organize Your Drawing210 265 31ch 06. qxd 3/30/07 5:50 PM Page 210 FIGURE 6. 19 ... the tools I have covered so far. Chapter 6 • Using Layers to Organize Your Drawing1 96 265 31ch 06. qxd 3/30/07 5:50 PM Page 1 96 2. Click the Layers drop-down list, and click the...

Ngày tải lên: 08/08/2014, 23:21

... 1&apos ;-0 " 12 1 ⁄2" = 1&apos ;-0 " 24 1 ⁄4" = 1&apos ;-0 " 48 1 ⁄8" = 1&apos ;-0 " 96 1 ⁄ 16& quot; = 1&apos ;-0 " 192 Defining a Text Style for Room Labels Now that ... the text. Masking is not supported for single-line text, but the Text Mask utility is avail- able in the Express Tools. Using Single-Line Text 295 265 31ch08.qxd 3/30/07...

Ngày tải lên: 08/08/2014, 23:21

... publish multiple layouts 0 navigate through the plot-style features Chapter 15 • Printing an AutoCAD Drawing6 06 265 31ch15.qxd 3/31/07 1:09 PM Page 60 6 3. Click the expansion arrow in the lower-right ... AutoCAD tem- porarily exits the viewport, pans or zooms the equivalent amount in paper space, Chapter 14 • Using Layouts to Set Up a Print 566 265 31ch14.qxd 3/30/07 6: 17 PM Page...

Ngày tải lên: 08/08/2014, 23:21

... completion, 62 5 63 3, 62 7, 62 9 floor, steps, and thresholds, 62 2 62 4, 62 3, 62 4 orbit tools, 63 7 63 8 pivot doors, 63 1, 63 1 63 2 roof, 63 4 63 6, 63 5, 63 6, 63 7 sliding glass door, 63 2, 63 2 walls, 61 3 61 5, 61 4, ... openings, 62 1, 62 1 62 2, 62 2 door block-outs, 61 6 61 8, 61 7, 61 8 doors and windows completion, 62 5 63 3, 62 7, 62 9 floor, steps, a...

Ngày tải lên: 08/08/2014, 23:21