autocad 2008 autocad lt 2008 no experience required - phần 4 docx

... located. 26531ch07.qxd 4/ 3/07 12:52 PM Page 241 4. Right-click, and choose Repeat List from the shortcut menu. 5. At the Select objects: prompt, click one of the arcs that repre- sents the balcony, ... Door 227 26531ch07.qxd 4/ 3/07 12:52 PM Page 227 NOTE If no objects are selected and you set Linetype Scale in the Prop- erties palette to a number other than 1.000, any noncontinuous li...

Ngày tải lên: 08/08/2014, 23:21

... 388 40 9 balcony, 40 8, 40 8 concrete hatch for foundation, 43 2 43 3, 43 3 copying, 41 8, 41 8 door and wall hatch, 43 3 43 6, 43 4, 43 5 door, step and windows, 40 2 40 8, 40 3 finishing touches, 40 8 40 9, 40 9 gradients ... command, 48 0, 48 0 48 2, 48 1 Continue command for, 47 9 48 0, 48 0 placing on drawing, 47 6 48 6 summary of changes, 47 0 vertical dimensions, 4...

Ngày tải lên: 08/08/2014, 23:21

... the Drop-Down Menus 13 26531ch01.qxd 3/30/07 4: 59 PM Page 13 AUTOCAD ® 2008 AND AUTOCAD LT ® 2008 NO EXPERIENCE REQUIRED ™ David Frey Jon McFarland Wiley Publishing, Inc. 26531fm.qxd 4/ 3/07 9:18 ... I say AutoCAD, I mean both AutoCAD and AutoCAD LT. I’ll also refer to AutoCAD LT as LT throughout this chapter and the rest of the book to specifically refer to th...

Ngày tải lên: 08/08/2014, 23:20

... 60' × 40 ' grid with 4& apos; dot spacing 8. Move the crosshair cursor to the upper-right corner of the grid, and check the coordinate readout. It should display 60&apos ;-0 ", 40 &apos ;-0 ", ... 4. 12. The results appear on the right of Figure 4. 12. FIGURE 4. 12: Selecting the second two lines to fillet (left) and the result of the second fillet (right) The tw...

Ngày tải lên: 08/08/2014, 23:20

... Figure 4. 53. FIGURE 4. 53: The block Figure 4. 54 gives you a graphic representation of the 12 steps necessary to complete the exercise. FIGURE 4. 54: The 12 steps for creating the block 1 2 3 4 567 8 9 11 10 12 Chapter ... the drawing as Cabin05a.dwg (see Figure 5. 14) . Drawing the Balcony: Drawing Circles 145 26531ch05.qxd 3/30/07 5:11 PM Page 145 Are You Experienced? Now you ca...

Ngày tải lên: 08/08/2014, 23:20

... 1&apos ;-0 " 12 1 ⁄2" = 1&apos ;-0 " 24 1 4& quot; = 1&apos ;-0 " 48 1 ⁄8" = 1&apos ;-0 " 96 1 ⁄16" = 1&apos ;-0 " 192 Defining a Text Style for Room Labels Now that ... some of which are beyond the scope of this book. For a more in-depth dis- cussion on blocks, see Mastering AutoCAD 2008 and AutoCAD LT 2008 by George Omura (Wile...

Ngày tải lên: 08/08/2014, 23:21

... following widths: 2&apos ;-0 ", 2&apos ;-6 ", 3&apos ;-0 ", and 3&apos ;-6 ". Chapter 9 • Using Dynamic Blocks and Tables3 64 26531ch09.qxd 3/30/07 6:11 PM Page 3 64 Note the small exclamation ... Stretch action 4. Select the door, and press ↵. 5. Turn off Polar and Osnap, and then at the Specify action loca- tion or [Multiplier/Offset]: prompt, click to place...

Ngày tải lên: 08/08/2014, 23:21

... performed a typi- cal installation of AutoCAD, the file should be in the C:\Program Files \AutoCAD 2008\ UserDataCache\Support folder. LT users should substitute AutoCAD LT 2008 for AutoCAD 2008 in the ... Gradients 442 26531ch11.qxd 3/30/07 6: 14 PM Page 44 2 5. Place the cursor on the new swatch of AR-RROOF, right-click, and choose Properties. The Tool Properties dialog b...

Ngày tải lên: 08/08/2014, 23:21

... line near the upper-right corner of the grid. 10. Be sure Snap is turned off. Then, enter the following: @ 140 < n90dw↵ @90 < s42d30'w↵ @ 140 < s67d30'e↵ @80 < n52d49'e↵ c↵ The ... notation. With the surveyor’s unit system, a sloping line that has an up-and-to-the-left direction has a down-and-to-the-right direction if you start from the opposite end. So, in laying...

Ngày tải lên: 08/08/2014, 23:21

... who do not wish to continue learning the 3D aspects of AutoCAD, I hope you have found the book useful in helping you learn AutoCAD 2008 and AutoCAD LT 2008. Good luck in your future with AutoCAD. ... is open. If it’s not, click the right-pointing arrow in the lower-right corner to open it. In the upper-right corner, make sure None is displayed in the Plot Style Table drop-down lis...

Ngày tải lên: 08/08/2014, 23:21