autocad 2008 autocad lt 2008 no experience required - phần 3 pps

... is controlled solely by the up-and-down motion. 26 531 ch05.qxd 3/ 30/07 5:11 PM Page 1 63 FIGURE 5.28: The Object Snap tab of the Drafting Settings dialog box Each of the 13 osnap options has a check ... position. Notice the drop-down list at the top of the Properties palette. This tells you that the currently selected object is a circle. Laying Out the Kitchen 1 53 26 531 ch05.qxd 3/ 3...

Ngày tải lên: 08/08/2014, 23:20

... the Drop-Down Menus 13 26 531 ch01.qxd 3/ 30/07 4:59 PM Page 13 AUTOCAD ® 2008 AND AUTOCAD LT ® 2008 NO EXPERIENCE REQUIRED ™ David Frey Jon McFarland Wiley Publishing, Inc. 26 531 fm.qxd 4 /3/ 07 9:18 ... I say AutoCAD, I mean both AutoCAD and AutoCAD LT. I’ll also refer to AutoCAD LT as LT throughout this chapter and the rest of the book to specifically refer...

Ngày tải lên: 08/08/2014, 23:20

... who do not wish to continue learning the 3D aspects of AutoCAD, I hope you have found the book useful in helping you learn AutoCAD 2008 and AutoCAD LT 2008. Good luck in your future with AutoCAD. ... styles and pen assign- ments later in this chapter. Using the Plot Dialog Box 5 83 26 531 ch15.qxd 3/ 31/07 1:09 PM Page 5 83 6. Close that plot-style table file, and open acad.stb...

Ngày tải lên: 08/08/2014, 23:21

... book. Instead of lengthy paragraphs of text that ultimately lead to nontangible infor- mation, this book addresses each subject in a step-by-step approach with literally over a thousand pictures ... Book Autodesk ® Revit ® Architecture 2011: No Experience Required. Does that mean if you have used Revit you won’t find this book advanced enough? No. This book is designed for anyone wh...

Ngày tải lên: 07/07/2014, 07:20

... equals 57 .3 degrees, and 36 0 degrees equals 6.28 radians, or 2π radians. AutoCAD uses r as the symbol for radians. Summarizing AutoCAD s Units 75 26 531 ch 03. qxd 3/ 30/07 5: 03 PM Page 75 FIGURE 3. 1: ... should display 60&apos ;-0 ", 40&apos ;-0 ", 0&apos ;-0 ". (In LT, you won’t have the third coordinate.) Setting Up the Drawing Size 65 26 531 ch 03. qxd 3...

Ngày tải lên: 08/08/2014, 23:20

... the preceding step. 7. Right-click once to open a context menu near your cursor (see Figure 6. 23) . FIGURE 6. 23: A right-click context menu Setting Up Layers 201 26 531 ch06.qxd 3/ 30/07 5:50 PM Page 201 11. ... lines to an end- point of the ridgeline Setting Up Layers 2 03 26 531 ch06.qxd 3/ 30/07 5:50 PM Page 2 03 shorter one. This linetype scale factor is global, meaning that it affe...

Ngày tải lên: 08/08/2014, 23:21

... move the text. Masking is not supported for single-line text, but the Text Mask utility is avail- able in the Express Tools. Using Single-Line Text 295 26 531 ch08.qxd 3/ 30/07 6:06 PM Page 295 Y ou ... lines Ǡ Managing single-line and multiline text Ǡ Adding hyperlinks 26 531 ch08.qxd 3/ 30/07 6:06 PM Page 281 FIGURE 8.2: The Text Style dialog box, in which text styles are set up 3. Enter...

Ngày tải lên: 08/08/2014, 23:21

... following widths: 2&apos ;-0 ", 2&apos ;-6 ", 3& apos ;-0 ", and 3& apos ;-6 ". Chapter 9 • Using Dynamic Blocks and Tables364 26 531 ch09.qxd 3/ 30/07 6:11 PM Page 36 4 Note the small exclamation ... block Creating a Dynamic Block 37 3 26 531 ch09.qxd 3/ 30/07 6:11 PM Page 37 3 7. At the Specify action location or [Base type]: prompt, place the Scale lightn...

Ngày tải lên: 08/08/2014, 23:21

... performed a typi- cal installation of AutoCAD, the file should be in the C:\Program Files \AutoCAD 2008\ UserDataCache\Support folder. LT users should substitute AutoCAD LT 2008 for AutoCAD 2008 in the ... Floor Plan 4 43 26 531 ch11.qxd 3/ 30/07 6:14 PM Page 4 43 dimension style. You have created a new dimension style that is a copy of the Standard style, and now you’ll ma...

Ngày tải lên: 08/08/2014, 23:21

... north of 30 ° and 30 minutes is shown as N30d30'E in AutoCAD notation. With the surveyor’s unit system, a sloping line that has an up-and-to-the-left direction has a down-and-to-the-right direction ... completed (see Figure 13. 3). FIGURE 13. 3: The property lines on the site drawing Drawing a Site Plan 515 26 531 ch 13. qxd 3/ 31/07 12 :31 PM Page 515 You want to dimension from the...

Ngày tải lên: 08/08/2014, 23:21