autocad 2008 autocad lt 2008 no experience required - phần 1 ppsx

... Drop-Down Menus 13 26531ch 01. qxd 3/30/07 4:59 PM Page 13 AUTOCAD ® 2008 AND AUTOCAD LT ® 2008 NO EXPERIENCE REQUIRED ™ David Frey Jon McFarland Wiley Publishing, Inc. 26531fm.qxd 4/3/07 9 :18 PM ... change. Introducing the AutoCAD Graphics Window 11 26531ch 01. qxd 3/30/07 4:59 PM Page 11 FIGURE 1. 1: The AutoCAD welcome screen provides access to the New Features...

Ngày tải lên: 08/08/2014, 23:20

... 3.05E+ 01, that is what is dis- played. The notation always uses an expression that indicates a number from 1 to 10 that is to be multiplied by a power of 10 . In this case, the power is 1, so the notation ... decimal degrees. For example, you enter an angle of 12 6°35&apos ;10 " as 12 6.586 or 12 6d35&apos ;10 ", and it displays as 12 6.58 61. AutoCAD uses a d instead of...

Ngày tải lên: 08/08/2014, 23:20

... inward 1 1 ⁄2", as in Figure 5. 31. FIGURE 5. 31: The offset shower polyline Next, draw the sink to the right of the shower. Constructing the Bathroom 16 1 26531ch05.qxd 3/30/07 5 :11 PM Page 16 1 If ... sidewalk. 20' 260' 20' 20' 60' 60' 10 ' 25' 40' R16' 20' 30' 10 ' 6' 17 0' 20' 15 ' 20'...

Ngày tải lên: 08/08/2014, 23:20

... step. 7. Right-click once to open a context menu near your cursor (see Figure 6.23). FIGURE 6.23: A right-click context menu Setting Up Layers 2 01 26531ch06.qxd 3/30/07 5:50 PM Page 2 01 11. Keep using ... for a Door 227 26531ch07.qxd 4/3/07 12 :52 PM Page 227 NOTE If no objects are selected and you set Linetype Scale in the Prop- erties palette to a number other than 1. 000, any nonco...

Ngày tải lên: 08/08/2014, 23:21

... 8 .1: Standard Scales and Their Corresponding Ratios Scale True Scale Factor 1& quot; = 1& apos ;-0 " 12 1 ⁄2" = 1& apos ;-0 " 24 1 ⁄4" = 1& apos ;-0 " 48 1 ⁄8" = 1& apos ;-0 " ... (With a scale of 1& quot; = 8&apos ;-0 ", which is another way of expressing the scale of 1 ⁄8" = 1& apos ;-0 ", each 1& apos ;-0 &qu...

Ngày tải lên: 08/08/2014, 23:21

... seg- ment’s endpoints. 11 . Repeat step 10 with the remaining arc segment. Setting Up Multiple Attributes in a Block 355 26531ch09.qxd 3/30/07 6 :11 PM Page 355 FIGURE 9 .11 : The floor plan with ... following widths: 2&apos ;-0 ", 2&apos ;-6 ", 3&apos ;-0 ", and 3&apos ;-6 ". Chapter 9 • Using Dynamic Blocks and Tables364 26531ch09.qxd 3/30/07 6 :11 PM Page 364...

Ngày tải lên: 08/08/2014, 23:21

... another 0 copy, move, and rotate elevations 2.0 3.0 1. 0 3.0 3.04.0 1. 0 DIA TOP 1. 0 1. 0 1. 0 2.0 2.0 1. 0 1. 5 FRONT RIGHT SIDE 6.0 Chapter 10 • Generating Elevations424 26531ch10.qxd 3/30/07 6 :10 ... Figure 11 .17 ). If the tile pattern looks OK, right-click again. FIGURE 11 .17 : The tiled hatch pattern in place Note that the user-defined pattern has no scale factor to worry...

Ngày tải lên: 08/08/2014, 23:21

... minutes is shown as N30d30'E in AutoCAD notation. With the surveyor’s unit system, a sloping line that has an up-and-to-the-left direction has a down-and-to-the-right direction if you start from ... with the lower-left corner of the patio. This locates the cabin on the site (see Figure 13 .5). Drawing a Site Plan 517 26531ch13.qxd 3/ 31/ 07 12 : 31 PM Page 517 9. Close the Site13a...

Ngày tải lên: 08/08/2014, 23:21

... to users of LT. 26531ch16.qxd 3/30/07 10 :13 PM Page 608 FIGURE 15 .13 : The cabin drawing ready for printing from a layout tab 6. In the Plot Scale area, the scale has been set to 1: 1. This is what ... publish multiple layouts 0 navigate through the plot-style features Chapter 15 • Printing an AutoCAD Drawing606 26531ch15.qxd 3/ 31/ 07 1: 09 PM Page 606 3. Click the expansion arrow...

Ngày tải lên: 08/08/2014, 23:21

... 632 walls, 613 – 615 , 614 , 615 window block-outs, 619 –620, 620 assigning plot-style table to, 603–604 balcony, 14 2 14 6 bathroom, 15 7, 15 7 16 6 shower unit, 15 9 16 1, 16 1 sink, 16 2, 16 2 toilet, 16 3 16 6, 16 4 creating ... 485 doors, 10 0, 10 0 12 4 alternate sliding-glass door, 12 4 dynamic block for, 369–370 rotating, 10 4 10 5, 10 5 sliding glass door, 11 4 12 4 s...

Ngày tải lên: 08/08/2014, 23:21