Camry Repair Manual SERVICE SPECIFICATION

... Washer No Mark No Mark w/ Washer SERVICE SPECIFICATIONS STANDARD BOLT SS–1 164AuthorĂ: DateĂ: STANDARD BOLT HOW TO DETERMINE BOLT STRENGTH SS0AE–03 SERVICE SPECIFICATIONS ENGINE MECHANICAL (5S–FE) SS–9 172AuthorĂ: ... in.) 0.02 mm (0.0008 in.) 0.02 mm (0.0008 in.) SS077–03 SS–14 SERVICE SPECIFICATIONS ENGINE MECHANICAL (1MZ–FE) 177AuthorĂ: DateĂ: TORQUE SPECIFICATION Part tightened N·...

Ngày tải lên: 28/04/2014, 13:32

... COUPE N–6 N–6 N–6 CELICA CONVERTIBLE — N – 6 N – 6 CAMRY TMC PRODUCTION Q–4 Q–4 Q–4 CAMRY TMMK PRODUCTION Q – 4 Q – 4 Q – 4 CAMRY COUPE Q–4 Q–4 — CAMRY SOLARA COVERTIBLE Q–4 — — SUPRA — — — R–3 AVALON ... N–6 CELICA CONVERTIBLE (RH) — N–1 N–1 CONVERTIBLE (LH) — N–5 N–5 CAMRY TMC PRODUCTION Q–4 Q–4 Q–4 CAMRY TMMK PRODUCTION Q – 4 Q – 4 Q – 4 CAMRY COUPE Q–4 Q–4 — CAMRY SOLARA C...

Ngày tải lên: 28/04/2014, 13:49

... AC0LJ–03 N13795 Quick Disconnect Adapter Charging Service Valve Hose N13794 Vacuum Pump Vacuum Pump Adapter N13791 Low Pressure Service Valve Vacuum Pump Adapter High Pressure Service Valve Manifold Gauge Set AC–10 –AIR ... ADAPTERS FROM SERVICE VALVES ON REFRIGERANT LINE HINT: Slide the sleeve of the quick disconnect adapter upward to un- lock the adapter and remove it from the serv...

Ngày tải lên: 28/04/2014, 12:52

... TRANSAXLE (A140E) SHIFT SOLENOID VALVE SL 1903A uthorĂ: DateĂ: SHIFT SOLENOID VALVE SL ON–VEHICLE REPAIR 1. REMOVE PARK/NEUTRAL POSITION SWITCH (See page AX–4) 2. DISCONNECT SHIFT SOLENOID VALVE ... TRANSAXLE (A140E) DIFFERENTIAL OIL SEAL AX–11 1904A uthorĂ: DateĂ: DIFFERENTIAL OIL SEAL ON–VEHICLE REPAIR 1. REMOVE LH AND RH DRIVE SHAFTS (See page SA–17) 2. REMOVE SIDE GEAR SHAFT OIL SEAL...

Ngày tải lên: 28/04/2014, 12:53

... TORQUE SPECIFICATIONS– IN–10 STANDARD BOLT TORQUE SPECIFICATIONS IN008–02 INTRODUCTION STANDARD BOLT TORQUE SPECIFICATIONS– IN–11 AUTOMATIC TRANSAXLE SERVICE SPECIFICATIONS– AX–12 SERVICE SPECIFICATIONS SERVICE ... in. 2.70 mm 0.1063 in. 2.75 mm 0.1083 in. 2.80 mm 0.1103 in. AUTOMATIC TRANSAXLE SERVICE SPECIFICATIONS– AX–18 TORQUE SPECIFICATION Part tightened N·m kgf·cm ft·lbf Stato...

Ngày tải lên: 28/04/2014, 13:01

... lock manual switch OFF or UNLOCK No continuity A16 – Ground Door lock manual switch LOCK Continuity A17 – Ground Door lock manual switch OFF or LOCK No continuity A17 – Ground Door lock manual ... Door lock manual switch OFF or UNLOCK No continuity A1 – Ground Door lock manual switch LOCK Continuity A2 – Ground Door lock manual switch OFF or LOCK No continuity A2 – Ground Door l...

Ngày tải lên: 28/04/2014, 13:03

... lock manual switch OFF or UNLOCK No continuity A16 – Ground Door lock manual switch LOCK Continuity A17 – Ground Door lock manual switch OFF or LOCK No continuity A17 – Ground Door lock manual ... Door lock manual switch OFF or UNLOCK No continuity A1 – Ground Door lock manual switch LOCK Continuity A2 – Ground Door lock manual switch OFF or LOCK No continuity A2 – Ground Door l...

Ngày tải lên: 28/04/2014, 13:07

... the same part number or equivalent. 2. It is very important to keep parts and the area clean when repairing the brake system. 3. If the vehicle is equipped with a mobile communication system, refer ... pad thickness through the caliper inspection hole and replace the pads if they are not within the specification. Minimum thickness: 1.0 mm (0.039 in.) 3. LIFT UP CALIPER (a) Remove the bolt a...

Ngày tải lên: 28/04/2014, 13:08

... cell. Standard specific gravity: 1.25 – 1.29 at 20°C (68°F) If the specific gravity is less than specification, charge the bat- tery. 3. Maintenance–Free Battery: CHECK BATTERY VOLTAGE (a) After ... terminals of the battery. Standard voltage: 12.5 – 12.9 V at 20°C (68°F) If the voltage is less than specification, charge the battery. Z18811 Maintenance–Free Battery Type A Type B Blue White R...

Ngày tải lên: 28/04/2014, 13:08

Ngày tải lên: 28/04/2014, 13:08