2000 toyota camry repair manual
Camry Repair Manual AIR CONDITION
... detector and repair if neces- sary (2) Charge proper amount of re- frigerant (3) If indicated pressure value is near 0 when connected to gauge, create the vacuum after inspecting and repairing the ... sure to read the following item carefully, then follow the correct procedure described in the repair manual. AC0M1–01 AC–36 –AIR CONDITIONING BLOWER UNIT 2518AuthorĂ: DateĂ: DISASSEMBLY 1. REMOVE ... both hand valves of manifold gauge set and stop the vacuum pump. Check the system for leaks and repair necessary. (e) Close both the high and low hand valves and stop the vac- uum pump. (f) Leave...
Ngày tải lên: 28/04/2014, 12:52
Camry Repair Manual AUTOMATIC TRANSAXLE
... bolt. (c) Pry up the pipe with a screwdriver and remove the pipe. 8. REMOVE MANUAL VALVE BODY Remove the 5 bolts and manual valve body. 9. REMOVE CONNECTOR CLAMP AND PIPE RETAINER Remove the 2 ... PARK/NEUTRAL POSITION (PNP) SWITCH AX–5 1925A uthorĂ: DateĂ: PARK/NEUTRAL POSITION (PNP) SWITCH ON–VEHICLE REPAIR 1. DISCONNECT PARK/NEUTRAL POSITION SWITCH CONNECTOR 2. REMOVE PARK/NEUTRAL POSITION SWITCH (a) ... TRANSAXLE (A140E) DIFFERENTIAL OIL SEAL AX–11 1904A uthorĂ: DateĂ: DIFFERENTIAL OIL SEAL ON–VEHICLE REPAIR 1. REMOVE LH AND RH DRIVE SHAFTS (See page SA–17) 2. REMOVE SIDE GEAR SHAFT OIL SEAL Using...
Ngày tải lên: 28/04/2014, 12:53
Camry Repair Manual AUTOMATIC TRANSAXLE MANUAL
... to another, thus controlling shifting and lock–up timing. INTRODUCTION GENERAL REPAIR INSTRUCTIONS– IN–4 GENERAL REPAIR INSTRUCTIONS 1. Use fender, seat and floor covers to keep the vehicle clean ... the same time. The component groups are inspected and repaired from the converter housing side. As much as possible, complete the inspection, repair and assembly before proceeding to the next com- ponent ... hammer and punch, drive out the pin. (d) Slide out the shaft and remove the manual valve lever from the case. 57. REMOVE MANUAL SHAFT OIL SEAL Remove the oil seal with a screwdriver. AUTOMATIC...
Ngày tải lên: 28/04/2014, 13:01
Camry Repair Manual BODY ELECTRICAL
... Door lock manual switch OFF or UNLOCK No continuity A1 – Ground Door lock manual switch LOCK Continuity A2 – Ground Door lock manual switch OFF or LOCK No continuity A2 – Ground Door lock manual ... No.1) 5. Wire Harness – – – BE–70 – Door lock system does not operate by manual switch. 1. Power Window Master Switch 2. Door Lock Manual Switch 3. Integration Relay (I/P J/B No.1) 4. Wire Harness BE–60 BE–70 BE–70 – Door...
Ngày tải lên: 28/04/2014, 13:03
Camry Repair Manual BODY ELECTRICAL BODY
... lock manual switch OFF or UNLOCK No continuity A16 – Ground Door lock manual switch LOCK Continuity A17 – Ground Door lock manual switch OFF or LOCK No continuity A17 – Ground Door lock manual ... No.1) 5. Wire Harness – – – BE–70 – Door lock system does not operate by manual switch. 1. Power Window Master Switch 2. Door Lock Manual Switch 3. Integration Relay (I/P J/B No.1) 4. Wire Harness BE–60 BE–70 BE–70 – Door...
Ngày tải lên: 28/04/2014, 13:07
Camry Repair Manual COOLANT
... the system with coolant. z Use of improper coolants may damage engine cool- ing system. z Use Toyota Long life Coolant” or equivalent and mix it with plan water according to the manufactur- er’s ... between the ”LOW” and ”FULL” lines, when the engine is cold. If low, check for leaks and add ’ Toyota Long Life Coolant” or Equivalent up to the ”FULL” line. 2. CHECK ENGINE COOLANT QUALITY (a)...
Ngày tải lên: 28/04/2014, 13:10
Camry Repair Manual DIAGNOSTICS
... switch ON. CHECK: Read temperature value on the OBD II scan tool or TOYOTA hand–held tester. OK: Temperature value: –40°C (–40°F) OK Repair or replace harness or connector. NG Check and replace ECM ... DateĂ: 1 Connect OBD II scan tool or TOYOTA hand–held tester, and read value of man- ifold absolute pressure. PREPARATION: (a) Connect the OBD II scan tool or TOYOTA hand–held tester to the DLC3. (b) ... ON and push the OBD II scan tool or TOYOTA hand–held tester main switch ON. CHECK: Read value of the manifold absolute pressure on the OBD II scan tool or TOYOTA hand–held tester. OK: Same as...
Ngày tải lên: 28/04/2014, 13:17
Camry Repair Manual EMISSION CONTROL
... malfunctioning. (f) TOYOTA Hand–Held Tester: Conclude forced driving of the VSV for the EVAP. (1) Stop the engine. (2) Disconnect the TOYOTA hand–held tester from the DLC3. (g) If you have no TOYOTA Hand–Held ... the purge line. (c) TOYOTA Hand–Held Tester: Forced driving of the VSV for the EVAP. (1) Connect a TOYOTA hand–held tester to the DLC3. (2) Start the engine. (3) Push the TOYOTA hand–held tester ... of fuel for reduced exhaust emissions Remark: * For inspection and repair of the SFI system, refer to the SF section of this manual. B01252 Air Disconnect Air Inlet Line Hose B01253 Pinch Push AA Pinch B01148 B01149 Air Purge...
Ngày tải lên: 28/04/2014, 13:17
Camry Repair Manual INTRODUCTION
... TO USE THIS MANUAL IN–1 1AuthorĂ: DateĂ: HOW TO USE THIS MANUAL GENERAL INFORMATION 1. INDEX An INDEX is provided on the first page of each section to guide you to the item to be repaired. To ... FI1066 IN0CO–04 Z11554 Seal Lock Adhesive IN–4 –INTRODUCTION REPAIR INSTRUCTIONS 4AuthorĂ: DateĂ: REPAIR INSTRUCTIONS GENERAL INFORMATION BASIC REPAIR HINT (a) Use fender, seat and floor covers to keep ... replace them with new parts. (5) Before repairs, remove the airbag sensor if shocks are likely to be applied to the sensor during repairs. (6) Never disassemble and repair the airbag sensor as- sembly,...
Ngày tải lên: 28/04/2014, 13:25
