sửa chữa xe ô tô điện trẻ em

... (petrol) except F7P 96528R1 Belt tension (in SEEM units) Fitting: 25 U.S. Minimum operating tension: 22 U.S. F8Q engine 99175R Belt tension (in SEEM units) Fitting: 38 U.S. Minimum operating tension: ... scratched or worn. (2) Wheel cylinder with integral fixed compensator: in the event of a wheel cylinder or compensator function fault: change the assembly, repair is forbidden. 48 238 12 10.5 18 6 0.07 20.6 ... it. NOTE : Do not refit a belt which has been removed. Change the belt if the tension is below the mini- mum operating tension. Belt tension (in SEEM units) Fitting : 30 U.S. Minimum operating...

Ngày tải lên: 22/10/2012, 15:42

... GEARBOXES Gearbox (Removal - Refitting) 21 Remove the idle speed regulation valve moun- ting. Disconnect the starter and oil pressure sensor wires. REMOVAL The gearbox is removed alone. Remove ... seal 91755R 85965R 21-29 MANUAL GEARBOXES Gearbox (Removal - Refitting) 21 Remove the three bolts securing the rear centre mounting and move it back as far as possible. 92108R1 NOTE: to make it easier to remove the bolts, ... 17.552 23-4 MANUAL GEARBOXES Differential output seal REMOVAL Remove the protective casing from under the en- gine. Drain the gearbox. Place the front of the vehicle on stands on the side in question. Remove the...

Ngày tải lên: 22/10/2012, 15:42

... Suspension arm bent - Side member bent - Suspension arm bent - Side member bent - Stub axle carrier bent - Stub axle carrier bent Suspension arm bent - See castor Side member bent - RH or LH stub ... system component parts, always mark the pipes before disconnecting them so that they can be reconnected in their original positions. This is essential. 30 "X" TYPE BRAKING SYSTEM with ... bolts (2). FRONT AXLE Combined spring - shock absorber assembly REMOVAL With the vehicle supported on axle stands, on the side concerned, remove : - the wheel, - the two shock absorber lower mounting...

Ngày tải lên: 22/10/2012, 15:42

... unit 61 REPLACEMENT The fan unit is removed after removing the upper water box seal and the external air intake grille. Remove the feed connector (A) and the 2 mounting bolts (B). Remove the fan ... correct? yes yes e53531.1 62 62-27 92289R1 92207R 92224R1 92203R HEATING Control cables 61 REPLACEMENT The control cables can be removed without removing the air distribution unit. Remove: - the control panel as described on the previous page, - ... grilles. Disconnect the fan feed connector (A). Remove the 2 fan mounting bolts (B) and remove the fan from the driver’s side (the water box can only be removed in one position). Remove: - the 2 radiator inlet...

Ngày tải lên: 22/10/2012, 15:42

Ngày tải lên: 22/10/2012, 15:42

... opening the hood Removal Remove the rear seals and slides. Remove the four plastic clips. 94787S TRIM FOR OPENING ELEMENTS (OTHER THAN SIDE) Hood exterior trim 73 C D 53 CABRIOLET Remove the front ... small side tensioning straps. 73-6 Removal: PRF7304 TRIM FOR OPENING ELEMENTS (OTHER THAN SIDE) Padding 73 D D 53 CABRIOLET After removing the external trim, remove the ri- vets from the rear section ... markers (notches) of template 2. Remove template 2. 98617R Apply an even layer of adhesive (using the large brush) to the marked section of the hood mate- rial. 73-16 Remove: - the speaker grille...

Ngày tải lên: 22/10/2012, 15:42

Ngày tải lên: 22/10/2012, 15:42

Ngày tải lên: 22/10/2012, 15:42

Ngày tải lên: 22/10/2012, 15:42

Ngày tải lên: 22/10/2012, 15:42

... ON THE SIDE MEMBER 1 Thickness of panels (mm) Cross member: 1.25 Side member: 1.25 Side member closure panel: 0.8 Unpicking 10 spot welds Welding BUTT WELDING JOINT ON THE SIDE MEMBER 2 Thickness ... front end cross member B Part front end cross member C Complete front end panel D Part front end panel E Side member closing panel F Front side member front section G Part front side member front ... the rear sub- frame removed, the jig allows positioning of the 1/2 unit (assembled wheel arch). 92638S FUEL TANK MOUNTING CROSS MEMBER During repairing of the rear (sub-frame removed), the jig allows...

Ngày tải lên: 22/10/2012, 15:42

Ngày tải lên: 22/10/2012, 15:42

... outer rubbing strip 66 I 94804R Remove the two screws (A). PRN6602 J D53 CABRIOLET 66-5 WINDOW SEALS Front door frame slide channel 66 D 92255R Remove the window. Remove the frame slide channel, ... rubbing strip C 66-1 WINDOW SEALS Rear door frame seal 66 E Remove the trim and the small fixed window Remove: the seal, which is very fragile, using an extra-flat chisel. Free the rear section ... cm. 92254S Remove the internal trim. Raise the rubbing strip a shown in the diagram. Front door outer rubbing strip B Front door inner rubbing strip C 66-1 WINDOW SEALS Rear door frame seal 66 E Remove...

Ngày tải lên: 22/10/2012, 15:42

Ngày tải lên: 27/04/2013, 10:43

Ngày tải lên: 30/11/2013, 11:41

Ngày tải lên: 25/12/2013, 15:01

Ngày tải lên: 30/12/2013, 20:48

Ngày tải lên: 03/07/2014, 19:20

Ngày tải lên: 03/07/2014, 19:20

Ngày tải lên: 03/07/2014, 19:20