... who exactly will benet from the project and how you envision
it happening.
ã Set benchmarks to evaluate progress toward your project goals.
ã Identify measurement methods.
Grant Management ... within the
committee.
Scholarship candidate
Provide contact information for the scholarship candidate.
Host counselor
The host counselor provides support for the scholar before and during the ... applicable), and beneciaries.
When an international
partner approaches
a host club with a
planned project, the
host club might accept
the project because
it doesn’t want to
offend the international...
... always separate the devices that
generate high voltage and high electrical noise from the low-voltage, logic-type devices such
as the S7-1200.
When configuring the layout of the S7-1200 inside ...
with SB
4 built-in I/O, 6
with SB
6 6
Single phase 3 at 100 kHz
SB: 2 at 30 kHz
3 at 100 kHz
1 at 30 kHz
SB: 2 at 30 kHz
3 at 100 kHz
3 at 30 kHz
3 at 100 kHz
3 at 30 kHz
High-speed ... to the bus connector on
the left side of the signal module.
3. Slip the hook extension of the female connector
into the housing at the bus connector and press
down slightly to engage the hook....
... of
the string defines the length of the string, which is the number of characters. Figure 4-10 shows
the format for a string. A string can have a length of 0 to 254 characters, plus the length ... KY THANH VIEN CUA WWW.ISSAUTOMATION.VN DE THUONG XUYEN NHAN DUOC TAI LIEU
S7-200 Programmable Controller System Manual
30
High-Speed Counters: HC
The high-speed counters c ount high-speed events ... to any electrical device, ensure that the power to that
equipment has been turned off. Also, ensure that the power to any related equipment has been
turned off.
Ensure that you follow all applicable...
... Remove the screws that secure the hard-drive bracket to the hard drive. Separate the hard-drive bracket from the
hard drive.
Installing the Hard Drive
1. Align the hard-drive bracket with the hard ... drive.
2. Tighten the screws on the hard drive to secure the hard-drive bracket to the hard drive.
3. Connect the hard drive connector to hard drive.
4. Slide the hard drive into the bay on the system ... Battery Charge LED Off/Hibernate Standby
Battery mode Discharging when Battery
charge is > 10%
Off Off
Discharging when Battery
charge is <=10%
Off Blinking White
Device Status Lights
Turns...
... of shock: Half-sine
Severity of shock: 15 g peak value, 11 ms duration
Direction of shock: 3 shocks each in +/– direction in each
of the three vertically aligned axes
Climatic environmental ... structure
The following documentation forms part of the S7-300 documentation package. You can also
find this, along with the associated entry ID, on the Internet
(http://support.automation.siemens.com/WW/view /en/
). ... each of three
vertically aligned axes
Climatic environmental conditions
The S7-300 may be operated on following environmental conditions:
Environmental conditions Permitted range Comments...
... frequency The contact will act when the output
frequency has reached the set frequency.
06: Up to desired frequency1 The contact will act when the output frequency has
reached the desired frequency ...
050.00
REV Hz
Switching to frequency adjustable
status.
030.00
REV Hz
Adjust the set frequency,that is the
value of CD000.
ENTER
030.00
REV Hz
Enter the new value which will be
remembered ...
07: Up to desired frequency2 The contact will act when the output frequency has
reached the desired frequency (CD062).
08: on accelerating The contact will act when the inverter is accelerating....
... organizan en
fichas etiquetadas por tarea. Los grupos de la cinta de opciones contienen
muchas de las herramientas y muchos de los controles disponibles en las barras
de herramientas y en los cuadros ... archivo en el
archivo activo, haga clic en él en la lista.
16 | Capítulo 2 Herramientas de la ventana de aplicación
Utilidades
No hay entradas
Modificadores de comandos
No hay entradas
Visualización ... sistema
CDATE
Almacena la fecha y la hora actuales en formato decimal.
DATE
Almacena la fecha y la hora actuales en formato de calendario juliano
modificado.
SAVENAME
Muestra el nombre de archivo y la...
... referencia
externa desde una paleta de herramientas
1 En la paleta de herramientas, haga clic con el botón derecho en una
herramienta de bloque o referencia externa. Haga clic en Propiedades.
2 En ... herramienta a la que hace referencia haciendo
clic con el botón derecho en la herramienta y especificando la nueva carpeta de
archivo de origen en el cuadro de diálogo Propiedades de herramientas.
Véase ... la
herramienta.
Barra de herramientas: Normal
Entrada de comandos: PALETASHERR
Para cambiar la imagen de una herramienta en una paleta de herramientas
1 En una paleta de herramientas, haga clic...
... primer CD en la unidad del equipo.
2 En el Asistente de instalación, haga clic en Instalar herramientas y
utilidades.
3 En la página Bienvenido al Asistente de instalación, haga clic en Siguiente.
4 ... del archivo
y su ubicación en el ordenador.
5 Pulse Guardar.
El contenido se descarga en el ordenador.
Para descargar contenido en un dibujo
1 En DesignCenter Online, haga clic en el encabezado ... un archivo de paleta de herramientas. Los archivos de
paleta de herramientas tienen la extensión de archivo .xtp.
Igualmente, se puede guardar y compartir un grupo de paletas de herramientas
exportándolo...
... de herramientas/paneles fijos.
■ Haga clic en la ficha Vista ➤ grupo Ventanas ➤ Bloqueo de
ventana ➤ Ventanas flotantes.
■ Haga clic en la ficha Vista ➤ grupo Ventanas ➤ Bloqueo de
ventana ➤ Ventanas ... siguientes acciones:
■ Haga clic en la ficha Vista ➤ grupo Ventanas ➤ Bloqueo de
ventana ➤ Barras de herramientas/paneles flotantes.
■ Haga clic en la ficha Vista ➤ grupo Ventanas ➤ Bloqueo de
ventana ... "startup"
3 Haga clic en Aceptar.
Referencia rápida
Comandos
No hay entradas
Variables de sistema
No hay entradas
Utilidades
No hay entradas
Modificadores de comandos
No hay entradas
Reproducción...