Quản trị mạng Pratical Question
Practical Questions QUESTION NO: 1 You are a Cisco certified expert. You have been contracted by the Labvn Pro chain to fix a problem that was caused by a MCP certified technician who could not complete the configuration of the routers. This Labvn Pro chain has three stores and wanted to maintain their bicycle repair business in a centralized manner through network connectivity. They then asked the local MCP certified technician to configure the routers, but the technician failed to establish connectivity among the routers. The routers are named Lab1, Lab2, and Lab3, respectively. Identify the faults(s) and make the appropriate change(s) to rectify the configuration of the routers. The MCP technician configured the routers with the specification that follows: • The routers are named Lab1, Lab2, and Lab3. • RIP is the routing protocol • Clocking is provided on the serial 0 interfaces • The password on each router is "cisco" • The subnet mask on all interfaces is the default mask. • The IP addresses are listed in chart below. Lab1 E0 192.168.27.1 E1 192.168.29.1 S0 192.168.31.1 Secret password: cisco Lab2 E0 192.168.35.1 S0 192.168.33.1 S1 192.168.31.2 Secret password: cisco Lab3 E0 192.168.37.1 S1 192.168.33.2 S ecret password: cisco To configure the router you need to click on the host icon that is connected to the router by a serial cable. iPMAC Network Training Center 1 QUESTION NO: 2 You are a network technician at Cisco, Inc. Cisco has recently opened a third office in a foreign country and bought a router to connect this office to the other two already on the network. The names of the routers are Lab1, Lab2, and Lab3. Configure the Lab3's router's IP addresses on the E0 and S1 interfaces so that the E0 interface receives the first usable subnet while the S1 interface receives the second usable subnet from the network 192.168.101.0/28. Both interfaces should receive the first available IP of the subnet. The zero subnet should not be used. The routers have been configured with the following specifications. The routers are named Lab1, Lab2, and Lab3. RIP is the routing protocol. Clocking is provided on the serial 0 interfaces The secret password on the Lab3 router is "cisco" The subnet mask of all networks other than 192.168.101.0 is the default mask. The IP addresses are listed in the chart below. MAC Net Lab1 E0 192.168.93.1 S0 192.168.95.1 Lab2 E0: 192.168.97.1 S0: 192.168.101.42 S1: 192.168.95.2 Lab3 E0 to be determined S1 to be determined Secret password: cisco Click on the host icon that is connect to a router by a serial console cable to configure the router. iP work Training Center 2 QUESTION NO: 3 Three sites, Lab1, Lab2, and Lab3 are connected via a WAN. At each site a router provides serial connectivity to the Wan and an Ethernet connection to a LAN. All three routers are configured, and the network is functional. Configure and apply an access list will prevent telnet access to the Lab1 router while allowing all other traffic to pass. The access list should not contain more than three (3) statements and should be applied to the Lab1 router. The routers have been previously configured with the following specifications: The routers are named Lab1, Lab2, and Lab3. RIP is the routing protocol. The clocking signal is provided on the serial 0 interfaces. All passwords on all routers are "cisco". The subnet mask on all the interfaces is the default mask. IP addresses are listed in the chart below. Lab1 E0 192.168.149.1 S0 192.168.199.1 Secret password: cisco Lab2 E0 192.168.155.1 S0 192.168.11.1 S1 192.168.199.2 Secret password: cisco Lab3 E0 192.168.165.1 S1 192.168.11.2 To configure the router click on the host icon that is connected to a router by a serial console cable. iPMAC Network Training Center 3 QUESTION NO: 4 You are a network technician at Lab, Inc. You are configuring the routing protocol on the Lab3 router to allow a host on the LAN to communicate with a host on the Lab2 router, where the Lab3 router is an addition to and already configured network that includes Lab1 and Lab2, each with one LAN respectively. The routers have been configures as follows: • The routers are named Lab1, Lab2, and Lab3. • RIP is the routing protocol • The clocking is provided on the serial 0 interfaces. • The secret password on the Lab3 router is "cisco" • The subnet masks on all interfaces is the default mask. • The IP addresses are listed in the chart Lab1 E0 192.168.149.1 S0 192.168.179.1 Lab2 E0 192.164.155.1 S0 192.168.111.1 S1 192.168.179.2 Lab3 E0 192.168.165.1 S1 192.111.2 To configure the router click on a host icon that is connected to a router by a serial cable. iPMAC Network Training Center 4 QUESTION NO: 5 Study the Exhibit below carefully: You are contracted as a network administrator at Cisco. You are required to configure two routers named Lab1 and Lab2 respectively. The network topology is shown in the exhibit above. The enable password is "cisco". You must configure the following passwords on the Lab2 router: • Console password: cisco • Vty lines 0-4 password: labvn To configure the router click on a host icon that is connected to a router by a serial cable. iPMAC Network Training Center 5 QUESTION NO: 6 You are a network technician at Cisco and have to locate and fix a router problem. Scenario is as follows: There are three routers named Lab1, Lab2, and Lab3 respectively. You know that Lab2 and Lab3 are 100% operational. The routing protocol being used is Single area OSPF. Lab1 has recently been installed and configured one of the trainees. However, he did not succeed in configuring Lab1 correctly. He tells you that connectivity is not complete because routing tables are not being updated correctly. You must now locate and fix this router configuration problem. Current configuration: Lab1 E0: 192.168.33.1/24 S0: 192.168.100.50/30 Secret Password: cisco Lab2 E0: 192.168.34.1/24 S0: 192.168.100.10/30 S1: 192.168.100.6/30 Secret Password: cisco Lab3 E0: 192.168.35.1/24 S1: 192.168.100.9/30 Secret Password: cisco Click on the picture of host connected to a router by a serial console cable. iPMAC Network Training Center 6 . Practical Questions QUESTION NO: 1 You are a Cisco certified expert. You have been contracted. connected to the router by a serial cable. iPMAC Network Training Center 1 QUESTION NO: 2 You are a network technician at Cisco, Inc. Cisco has recently