PULSE CODE MODULATION

EXPERIMENT # 8 PULSE CODE MODULATION 1/27/2010 Group: PURPOSE The objectives of this laboratory are: 1. To investigate the serially encoded PCM signal. 2. To make signal-to-noise measurements of the PCM system. 3. To investigate synchronous and asynchronous PCM techniques. 4. To investigate properties of the TDM-PCM communication system. EQUIPMENT LIST 1. PC With Matlab and Simulink Laboratory Procedure I . PCM Familiarization A. The analog to digital conversion properties of the PCM was investigated in the last experiment. The “start” bit and the 7 data bits and two “stop” bits were identified. It was also found that if the parity switch is on, then the 1 st stop bit is changed to an even parity bit. That is, the 7 data bits plus the parity bit will always be an even number (refer to figure 8 B) B. Set up Figure 8A. the MSB-LSB quantization switches are to be implemented using the Sample and hold and Quantizer blocks. The outputs is to be fed via a MUX and the input compared with the output and the error in tracing the signal is observed using a very low frequency sine wave. The effect of changes in amplitude should also be studied. All the results should match the ones summarized below. figure 8A (a) PCM timing The output of the above circuit implementation is shown below in the following CRO’s. figure 8A (b) Input to PCM timing The output muxed with the input is shown in figure below figure 8A (c) Output Muxed with Input for PCM timing The block parameters of the quantizer is shown below figure 8A (d) Quantizer block parameters The whole PCM timing block implementation is shown below figure 8A (e) PCM timing- Full implementation Here are the block paramters of the quantizer encode and the decode blocks. The triger signal is provided using a pulse generator. figure 8A (f) Block Parameters Enabled quantizer encode Similarly the block parameters for the quantization decode is shown below. figure 8A (g) Block Parameters Enabled quantizer decode The digital output signal is as shown below. figure 8A (h) Block Parameters Enabled quantizer decode The quantization values are shown below figure 8A (i) Quantization values The distortion is shown below figure 8A (j) Distortion of the signal The final output of the decoder is shown below figure 8A (k) Output in comparision with the input C. The switches in the PCM-Analog module was set to SYNC / ASYNC --- SYNC Adjust the analog input signal for a 1 kHz since wave. The output of the PCM decoder was observed. The output was also fed to a LPF to reconstruct the signal. The effect of the LPF to signal reconstruction is important since it changes the amplitude of the frequency domain signal. II PCM SNR MEASURMENT A. As shown in figure 8c a communication channel has been added to the PCM system. A constant number of quantization levels (2 7 ), the error signal will be a function of the communication channel SNR. Therefore, we measured the SNR at the output of the system and compared it to the SNR in the communication channel. The output SNR was plotted as a function of the channel SNR. ( A 20 Hz since wave (3v p-p) should be used as the analog input.) We could have also decreased the signal level in the channel to get a wide variation of S/N ratio by inserting the 50Ω feedthru. B. A scheme as been incorporated into the PCM system for the compensation of errors generated by noise. With the parity switch ON, one of the stop bits is changed to a parity bit. Now the eight-bit data word (surrounded by the start and stop bits) will always have an even number of bits. The error compensation scheme works as follows: figure 8B (a) PCM channel in Noise The output block looks like this figure 8B (b) Output of PCM channel in Noise The block parameters of the Band limited White noise looks like this figure 8B (c) Block Parameters of Band limited White Noise The other module outputs are shown below The digital signal generated looks like this figure 8B (d) Output of the digital signal generator The quantization values and the error is shown below figure 8B (e) Quantization values [...]... observed and a plot similar to the previous time was done C The parity switch was turned off and the system has been operating in a “synchronous” mode That is, the timing system is common to both encoder and decoder Asynchronous mode will utilize the start and stop bits of the PCM word for obtaining word timing The loss of the start bit due to channel noise will not only causes a word error, but also causes . EXPERIMENT # 8 PULSE CODE MODULATION 1/27/2010 Group: PURPOSE The objectives of this laboratory are: 1. To investigate the serially encoded PCM signal quantizer encode and the decode blocks. The triger signal is provided using a pulse generator. figure 8A (f) Block Parameters Enabled quantizer encode Similarly