Đây là hướng dẫn sử dụng phần mềm Mastercam-X4. hướng dẫn có các hình ảnh và ví dụ cụ thể
Wire Training TutorialsTo order more books:Call 1-800-529-5517 orVisit www.inhousesolutions.com orContact your Mastercam Dealer Mastercam X4 Training Tutorials Wire ApplicationsDate: August 6,2009Copyright © 1984 2009 In House Solutions Inc. All rights reserved.Software: Wire Mastercam X4Author: Mariana LendelISBN: 978 1 926566 39 9NoticeIn House Solutions Inc. reserves the right to make improvements to this manual at any time andwithout notice.Disclaimer Of All Warranties And LiabilityIn House Solutions Inc. makes no warranties, either express or implied, with respect to thismanual or with respect to the software described in this manual, its quality, performance,merchantability, or fitness for any particular purpose. In House Solutions Inc. manual is sold orlicensed "as is." The entire risk as to its quality and performance is with the buyer. Should themanual prove defective following its purchase, the buyer (and not In House Solutions Inc., itsdistributor, or its retailer) assumes the entire cost of all necessary servicing, repair, of correctionand any incidental or consequential damages. In no event will In House Solutions Inc. be liablefor direct, indirect, or consequential damages resulting from any defect in the manual, even if InHouse Solutions Inc. has been advised of the possibility of such damages. Some jurisdictions donot allow the exclusion or limitation of implied warranties or liability for incidental orconsequential damages, so the above limitation or exclusion may not apply to you.CopyrightsThis manual is protected under the copyright laws of Canada and the United States. All rights arereserved. This document may not, in whole or part, be copied, photocopied, reproduced,translated or reduced to any electronic medium or machine readable form without priorconsent, in writing, from In House Solutions Inc.TrademarksMastercam is a registered trademark of CNC Software, Inc.Microsoft, the Microsoft logo, MS, and MS DOS are registered trademarks of MicrosoftCorporation; Mastercam Verify is created in conjunction with Sirius Systems Corporation;Windows 95, and Windows NT; Windows XP are registered trademarks of MicrosoftCorporation.Acknowledgements"Thanks to the In House Solutions team for helping in the production and marketing of thisbook. It simply wouldn't be the same without all your efforts. Finally, thank you, the reader formaking this purchase; I hope it serves you well."Mariana Lendel TABLE OF CONTENTSGetting Started A 1TutorialsTutorial #1, 2D Geometry Contour . 1 1Tutorial #2, 2D Multi Contour 2 1Tutorial #3, 3D Geometry and 4 Axis Wire path . 3 1Tutorial #4, Punch And Die Created From the Same Work Piece 4 1Tutorial #5, Multiple Tabs 5 1Tutorial #6, No Core Wire path 6 1General Notes B1 TUTORIAL SERIES FORTUTORIAL #2WIRE 2D MULTIPLE CONTOURS WIRE X4TUTORIAL 2Objectives:The Student will design a 2 Dimensional drawing by:Getting a file already created.Deleting the outer rectangle.Mirroring the geometry about Y axis.Creating a rectangle.Modifying the geometry by breaking a line in two pieces.Creating points.The Student will create a Die using the Contour wire path by:Setting the wire library for skim cuts.Selecting the contours using Window options.Setting the parameters in Contour Parameter dialog box.Editing the NCI file.The Student will check the toolpath using Mastercam’s Backplot and Verify verification.Page 2 2 WIRE X4TUTORIAL 2GEOMETRY CREATIONUSEFUL TOOLS TO START THE GEOMETRY CREATIONBefore starting the geometry creation we should customize the toolbars to see the toolbars requiredto create the geometry and machine a Wire part. See Getting started page A 4.Before starting the geometry make sure that the Grid is enabled. It will show you at each momentwhere is the part origin. See Getting started page A 5 for details.Toolpaths/Solids manager to the left of the screen can be hidden to gain more space in the graphicarea for design. Press Alt + O to remove it.Page 2 3 . Wire Training TutorialsTo order more books:Call 1-8 0 0-5 2 9-5 517 orVisit www.inhousesolutions.com orContact your Mastercam Dealer Mastercam