Hướng dẫn sử dụng phần mềm Mastercam-X4 - P16

Đây là hướng dẫn sử dụng phần mềm Mastercam-X4. hướng dẫn có các hình ảnh và ví dụ cụ thể

Professional CoursewareMastercam X4 RouterTo order more books:Call 1 800 529 5517 orVisit www.inhousesolutions.com orContact your Mastercam Dealer Mastercam X4 Training Tutorials – Professional Courseware RouterDate: July 2, 2009Copyright © 1984 2009 In House Solutions Inc. All rights reserved.Author: Mariana LendelISBN: 978 1 926566 33 7NoticeIn House Solutions Inc. reserves the right to make improvements to this manual at any time and withoutnotice.Disclaimer of All Warranties and LiabilityIn House Solutions Inc. makes no warranties, either express or implied, with respect to this manual orwith respect to the software described in this manual, its quality, performance, merchantability, or fitnessfor any particular purpose. In House Solutions Inc. manual is sold or licensed "as is." The entire risk as toits quality and performance is with the buyer. Should the manual prove defective following its purchase,the buyer (and not In House Solutions Inc., its distributor, or its retailer) assumes the entire cost of allnecessary servicing, repair, or correction, and any incidental or consequential damages. In no event willIn House Solutions Inc. be liable for direct, indirect, or consequential damages resulting from any defectin the manual, even if In House Solutions Inc. has been advised of the possibility of such damages. Somejurisdictions do not allow the exclusion or limitation of implied warranties or liability for incidental orconsequential damages, so the above limitation or exclusion may not apply to you.CopyrightsThis manual is protected under the copyright laws of Canada and the United States. All rights arereserved. This document may not, in whole or part, be copied, photocopied, reproduced, translated orreduced to any electronic medium or machine readable form without prior consent, in writing, from InHouse Solutions Inc.TrademarksMicrosoft, the Microsoft logo, MS, and MS DOS are registered trademarks of Microsoft Corporation;Mastercam Verify is created in conjunction with Sirius Systems Corporation; Windows 95, Windows NT;and Windows XP are registered trademarks of Microsoft Corporation. Router X42D GEOMETRY CREATION2D GEOMETRY COURSE CONTENT2. OVERVIEW OF THE GRAPHIC USER INTERFACE . 43. SETTING THE TOOLBAR STATES FOR ROUTER . 54. SETTING THE GRID . 65. NAVIGATE THROUGH MASTERCAM 76. ABOUT RIGHT MOUSE CLICK MENU . 117. CREATE DRAWING # 1 . 138. EXERCISE USING CREATE POINT POSITION COMMAND 139. EXERCISE USING CREATE RECTANGLE COMMANDS . 1410. EXERCISE USING CREATE LINE COMMANDS . 1411. EXERCISE USING CREATE ARC COMMANDS 1612. EXERCISE USING FILLET COMMAND . 1613. CREATE DRAWING # 2 . 1814. ANGLE MEASUREMENT . 2015. EXERCISE USING CREATE ARC POLAR COMMANDS 2016. EXERCISE USING TRIM COMMAND . 2117. EXERCISE USING BREAK AND JOIN COMMANDS . 2418. EXERCISE USING MIRROR COMMAND 2519. CREATE DRAWING #3 2620. EXERCISE USING OFFSET COMMANDS 2621. CREATE DRAWING #4 2722. CREATE DRAWING #5 . 28Page 1 Router X42D GEOMETRY CREATION23. CREATE DRAWING #6 2824. EXERCISE USING ROTATE COMMAND . 2825. CREATE DRAWING #7 2926. CREATE DRAWING #8 2927. CREATE DRAWING #9 3028. EXERCISE TO CREATE TANGENT ARCS . 3029. CREATE DOOR DRAWING #10 . 3130. REVIEW – CREATE DOOR DRAWING #11 3231. CREATE DRAWING #12 3232. EXERCISE TO CREATE TANGENT LINES 3333. EXERCISE USING POLYGON COMMAND 3434. REVIEW EXERCISE – DRAWING # 13 3435. CREATE DRAWING # 14 . 3536. CREATE DRAWING #15 3537. EXERCISE USING TRANSLATE COMMAND . 3638. CREATE DRAWING # 16 . 3739. EXERCISE USING ANALYZE COMMAND . 3740. EXERCISE USING ATTRIBUTES COMMAND 3941. MANAGE LEVELS . 4042. EXERCISE USING CHANGE ATTRIBUTES COMMAND . 4243. CREATE DRAWING # 17 . 4344. DIMENSION GEOMETRY 4345. XFORM NESTING . 44Page 2 Router X42D GEOMETRY CREATION46. REVIEW EXERCISE DRAWING # 18 4647. OPTIONAL – SOLID DRAWING #1 4748. EXERCISE USING ANALYZE CHAIN COMMAND 4849. CONVERTING DRAWINGS FROM DIFFERENT CAD PACKAGES 5150. CUSTOMIZING THE BUTTONS AND KEYS USING SETTINGS . 52Page 3 Router X4TOOLPATH CREATION2D TOOLPATH CREATION CONTENT1. CHAINING OPTIONS. 63DRAWING # 1 652. MACHINE DEFINITION 653. PROPERTIES . 654. CREATING A PROFILE TOOL AND MACHINING A TABLE TOP . 66DRAWING # 7 775. DRILLING TOOLPATH 786. REVIEW EXERCISE DRAWING # 6 . 81DRAWING # 14 857. MACHINE THE POKER TABLE 85DRAWING # 9.MCX 918. POCKET TOOLPATH 91DRAWING # 17 979. ENGRAVING . 9710. USING RAST2VEC IMPORT A BITMAP . 104DRAWING # 10.MCX 10811. POCKET (ISLAND FACING) TO MACHINE THE PANELS. 10812. CIRCMILL THE HOLE (OPTIONAL) 111Page 61 Router X4TOOLPATH CREATION13. MACHINE THE OPEN POCKETS IN THE LEFT SIDE TOOL PLANE (OPTIONAL) 11214. DRILL THE HOLES IN THE LEFT SIDE TOOL PLANE (OPTIONAL) 11315. BLOCK DRILLING 11416. MACHINING THE NESTED PARTS 11617. TOOLPATH NESTING 121DRAWING # 11.MCX 12618. REVIEW POCKET (ISLAND FACING) TO MACHINE THE PANELS . 12619. TOOLPATH NESTING FROM SOLIDS 133DRAWING # 18 14520. MACHINE THE CLOCK . 145Page 62 123doc.vn