B&R training - First acopos project Basic training how to initiate an acopos project with X20 CPU
Creating an Automation Studio project with an X20 CPU | ENG We reserve the right to change the content of this manual without prior notice The information contained herein is believed to be accurate as of the date of publication, however, B&R makes no warranty, expressed or implied, with regards to the products or the documentation contained within this document B&R shall not be liable in the event if incidental or consequential damages in connection with or arising from the furnishing, performance or use of these products The software names, hardware names and trademarks used in this document are registered by the respective companies Copyright © B&R – Subject to change without notice 1/7 Creating an Automation Studio project with an X20 CPU | ENG Table of Contents OVERVIEW .3 CREATE A NEW PROJECT CONFIGURE HARDWARE Copyright © B&R – Subject to change without notice 2/7 Creating an Automation Studio project with an X20 CPU | ENG Overview Learning Targets Creating a new project Configuring hardware Learning Duration Copyright © B&R – Subject to change without notice 3/7 Creating an Automation Studio project with an X20 CPU | ENG Create a new project Click the New Project ( Click the An empty project ( Copyright © B&R – Subject to change without notice ) hyperlink ) hyperlink 4/7 Creating an Automation Studio project with an X20 CPU | ENG Click the Name of the project input field Enter First_Project into the Name of the project field Click the Next > ( Copyright © B&R – Subject to change without notice ) button 5/7 Creating an Automation Studio project with an X20 CPU | ENG Configure hardware Double-click the Name of the configuration input field Enter X20CPU into the Name of the configuration field Click the Next > ( Copyright © B&R – Subject to change without notice ) button 6/7 Creating an Automation Studio project with an X20 CPU | ENG Click the Search input field Enter X20CP1586 in the field Click X20CP1586 Click the Finish ( Copyright © B&R – Subject to change without notice ) button 7/7 Establishing an online connection | ENG We reserve the right to change the content of this manual without prior notice The information contained herein is believed to be accurate as of the date of publication, however, B&R makes no warranty, expressed or implied, with regards to the products or the documentation contained within this document B&R shall not be liable in the event if incidental or consequential damages in connection with or arising from the furnishing, performance or use of these products The software names, hardware names and trademarks used in this document are registered by the respective companies Copyright © B&R – Subject to change without notice 1/6 Establishing an online connection | ENG Table of Contents OVERVIEW .3 ESTABLISHING AN ONLINE CONNECTION Copyright © B&R – Subject to change without notice 2/6 Establishing an online connection | ENG Overview Learning Targets Open online settings Search network Establish and save connection Learning Duration Copyright © B&R – Subject to change without notice 3/6 Adding an ACOPOS drive | ENG Click the Next > ( Click the Skip this page ( Copyright © B&R – Subject to change without notice ) button ) list item 7/12 Adding an ACOPOS drive | ENG Click the Next > ( ) button Click the Next > ( ) button Copyright © B&R – Subject to change without notice 8/12 Adding an ACOPOS drive | ENG Click the Next > ( ) button Click the Both end switches are normally open ( checkbox Click the Quick stop ist normally open ( Click the Next > ( Copyright © B&R – Subject to change without notice ) ) checkbox ) button 9/12 Adding an ACOPOS drive | ENG Click the Next > ( ) button Double-click the Powered by ( Copyright © B&R – Subject to change without notice ) list item 10/12 Adding an ACOPOS drive | ENG Click the DC ( ) list item Double-click the Supply voltage ( ) list item Enter 24 into the Supply voltage value field Click the Finish ( Copyright © B&R – Subject to change without notice ) button 11/12 Adding an ACOPOS drive | ENG Copyright © B&R – Subject to change without notice 12/12 Opening and using the NC Test window | ENG We reserve the right to change the content of this manual without prior notice The information contained herein is believed to be accurate as of the date of publication, however, B&R makes no warranty, expressed or implied, with regards to the products or the documentation contained within this document B&R shall not be liable in the event if incidental or consequential damages in connection with or arising from the furnishing, performance or use of these products The software names, hardware names and trademarks used in this document are registered by the respective companies Copyright © B&R – Subject to change without notice 1/9 Opening and using the NC Test window | ENG Table of Contents OVERVIEW .3 DESCRIPTION IN DETAIL Copyright © B&R – Subject to change without notice 2/9 Opening and using the NC Test window | ENG Overview Learning Targets Open the test window Switching on and homing an axis Starting a positive movement Learning Duration Copyright © B&R – Subject to change without notice 3/9 Opening and using the NC Test window | ENG Description in detail Right-click the 8V1010.50-2 image Click the Test ( Copyright © B&R – Subject to change without notice ) menu item 4/9 Opening and using the NC Test window | ENG Click gAxis01 ( Click the OK ( Copyright © B&R – Subject to change without notice ) ) button 5/9 Opening and using the NC Test window | ENG Click the Exclusive Mode ( Click the Controller ( Copyright © B&R – Subject to change without notice ) button ) tree item 6/9 Opening and using the NC Test window | ENG Double-click the Switch on ( Double-click the Homing ( Copyright © B&R – Subject to change without notice ) menu item ) tree item 7/9 Opening and using the NC Test window | ENG Click the Basis Movement ( Double-click the Positive ( Copyright © B&R – Subject to change without notice ) tree item ) tree item 8/9 Opening and using the NC Test window | ENG Copyright © B&R – Subject to change without notice 9/9 ... Automation Studio project with an X20 CPU | ENG Click the Name of the project input field Enter First_ Project into the Name of the project field Click the Next > ( Copyright © B&R – Subject to... notice 3/7 Creating an Automation Studio project with an X20 CPU | ENG Create a new project Click the New Project ( Click the An empty project ( Copyright © B&R – Subject to change without notice... Copyright © B&R – Subject to change without notice 1/7 Building and transferring a project | ENG Table of Contents OVERVIEW .3 BUILDING AND TRANSFERRING A PROJECT .4 PROJECT BUILD