1. Trang chủ
  2. » Kỹ Thuật - Công Nghệ

Sửa chữa DAEWOO-LACETTI 2010 - P10

15 316 6
Tài liệu đã được kiểm tra trùng lặp

Đang tải... (xem toàn văn)

Tài liệu hạn chế xem trước, để xem đầy đủ mời bạn chọn Tải xuống

THÔNG TIN TÀI LIỆU

Thông tin cơ bản

Định dạng
Số trang 15
Dung lượng 1,47 MB

Nội dung

The Daewoo Lacetti is a compact car made by the South Korean automaker GM Daewoo since 2002. The first-generation Lacetti was available as a four-door sedan, a five-door hatchback or a five-door station wagon.

NUBIRA/LACETTI SEALING, CAULKING AND DEADNER 9–1SECTION 9SEALING, CAULKING AND DEADNERCONTENTS1. SEALING & CAULKING 9 – 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2. DEADNER 9 – 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.1.GENERAL DESCRIPTION 9–14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.2.REPAIR PROCEDURE 9–14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9–2 SEALING, CAULKING AND DEADNER NUBIRA/LACETTI1. SEALING & CAULKINGNote : Seal the following areas to prevent air leaks water leaks, and rust.ENGINE ROOM .Fig. 1 Engine Room NUBIRA/LACETTI SEALING, CAULKING AND DEADNER 9–3ENGINE ROOMFig. 2 Engine Room 9–4 SEALING, CAULKING AND DEADNER NUBIRA/LACETTIDASHFig. 3 Dash NUBIRA/LACETTI SEALING, CAULKING AND DEADNER 9–5FLOOR & TRUNK ROOMFig. 4 Floor & Trunk Room 9–6 SEALING, CAULKING AND DEADNER NUBIRA/LACETTIREAR LAMP & TRUNK ROOMFig. 5 Rear Lamp NUBIRA/LACETTI SEALING, CAULKING AND DEADNER 9–7Fig. 6 Rear Lamp 9–8 SEALING, CAULKING AND DEADNER NUBIRA/LACETTIROOFFig. 7 Roof NUBIRA/LACETTI SEALING, CAULKING AND DEADNER 9–9ROOFFig. 8 Roof 9–10 SEALING, CAULKING AND DEADNER NUBIRA/LACETTISUN ROOFFig. 9 Sun Roof . the damaged deadner.S Peel off the damaged deadner with a steel spatula, care-fully..3. Clean and dry.S Before applying the deadner, thoroughly clean and. areas to be applied..4. Prelocation the new deadner on the panels to be ap-plied..Note : Avoid the parts mounting holes and service holes..5. Adhension

Ngày đăng: 30/10/2012, 08:48

TỪ KHÓA LIÊN QUAN

TÀI LIỆU CÙNG NGƯỜI DÙNG

TÀI LIỆU LIÊN QUAN