Tóm tắt những kết quả mới của luận án: Đã xác định các điều kiện tổng hợp vật liệu nano silic từ trấu. Đã chế tạo được anode trên cơ sở nano Si cho các đặc trưng điện hóa như dung lượng riêng cao, mật độ dòng điện lớn, số chu kỳ phóng nạp, hiệu suất Coulomb cao.
MINISTRY OF EDUCATION AND TRAINING MINISTRY OF NATIONAL DEFENCE ACADEMY OF MILITARY SCIENCE AND TECHNOLOGY NGUYEN VAN THANG STUDY ON THE SYNTHESIS PROCESS OF SILICON NANOMATERIALS TO FABRICATE ANODE ORIENT APPLICATION FOR Li-ION BATTERIES DOCTORAL THESIS OF CHEMISTRY Hanoi – 2019 MINISTRY OF EDUCATION AND TRAINING MINISTRY OF NATIONAL DEFENCE ACADEMY OF MILITARY SCIENCE AND TECHNOLOGY NGUYEN VAN THANG STUDY ON THE SYNTHESIS PROCESS OF SILICON NANOMATERIALS TO FABRICATE ANODE ORIENT APPLICATION FOR Li-ION BATTERIES Specialization: Theoretical chemistry and Physical chemistry Code: 44 01 19 DOCTORAL THESIS OF CHEMISTRY Scientific supervisors: Dr Nguyen Tran Hung Assoc Prof Dr Nguyen Manh Tuong Hanoi – 2019 i STATEMENT OF AUTHORSHIP I assure that the thesis is my own research work The data and results presented in the dissertation are honest and have not been unpublished in other work The reference is fully cited Hanoi, date: Ph.D student Nguyen Van Thang ii ACKNOWLEDGMENTS First of all, I would like to express their deep gratitude to my supervisors Dr Nguyen Tran Hung and Assoc Prof Dr Nguyen Manh Tuong for their direct instruction guidance and support throughout my thesis implementation process I am grateful for the help of the Training Department, Academy of Military Science and Technology throughout the complete process of the thesis I sincerely express my deepest thanks to the head of the Institute of Materials Chemistry, the head of the Nanomaterials Department, the colleagues and my friends for their encouragement Ph.D student Nguyen Van Thang iii TABLE OF CONTENTS Page LIST OF FIGURES .vi LIST OF TABLES x LIST OF SYMBOLS AND ABBREVIATIONS xi INTRODUCTION CHAPTER 1: OVERVIEW 1.1 Overview of LIB 1.1.1 The new generation of electrochemical sources 1.1.2 LIB 1.1.3 Domestic and foreign research situation on LIB .13 1.2 Anode materials of LIB 15 1.2.1 Ion storage material 15 1.2.2 Anode graphene 17 1.2.3 Anode from silicon material, silicon nanoparticles/graphene 19 1.3 Methods of synthesis silicon nanoparticles and current progress of thermodynamics, the kinetics of synthesis of silicon nanoparticles from rice husk .21 1.3.1 Overview of silicon 21 1.3.2 Introduction about rice husk and current status of rice husk use in our country 26 1.3.3 The synthesis nano Si from rice husk .27 1.4 Synthesis methods of graphene 29 1.4.1 Overview of graphene 29 1.4.2 Synthesis methods of graphene 31 1.5 Kinetics and thermodynamics .35 1.5.1 Kinetic conditions .35 1.5.2 Thermal analysis and reaction kinetics study by thermal analysis .36 1.5.3 Thermodynamic conditions .39 CHAPTER 2: SUBJECTS AND METHODS OF RESEARCH 41 2.1 Research subjects 41 2.2 Research Methods 41 iv 2.2.1 The synthesis method of nano Si from rice husk .41 2.2.2 Kinetic, thermodynamic characteristics of synthesis nano Si from rice husk .45 2.2.3 Synthesis of rGO from graphite 46 2.3 Synthesis of nano Si@rGO material for LIB's anode 47 2.4 Fabrication of LIB to test electrochemical properties of anode materials 48 2.4.1 The fabrication process of LIB’s anode 48 2.4.2 LIB fabrication process 49 2.5 Methods of studying the composition and material structure 50 2.5.1 Scanning electron microscope (SEM) method 50 2.5.2 Energy-dispersive X-ray spectroscopy (EDX) method 51 2.5.3 Transmission electron microscopy (TEM) method .51 2.5.4 Fourier-transform infrared spectroscopy method (FT-IR) 51 2.5.5 X-ray diffraction method (XRD) .52 2.5.6 Isothermal method adsorbed gas nitrogen 52 2.6 Methods of surveying electrochemical properties of electrodes .52 2.6.1 Cyclic voltammetry (CV) 52 2.6.2 Galvanostatic charge-discharge (GC) .55 CHAPTER 3: RESULTS AND DISCUSSION 57 3.1 Synthesis silica nanoparticles from rice husk 57 3.1.1 Investigate the effects of acid treatment 57 3.1.2 Investigate the effects of calcination mode 61 3.1.3 Thermodynamics, the kinetics of the process of synthesis silica nanoparticles from rice husk 67 3.2 Synthesis of silicon nanoparticles from silica nanoparticles 72 3.2.1 Investigation of factors affecting silicon nanoparticles synthesis process 72 3.2.2 Kinetics of the process of synthesis silicon nanoparticles from silica nanoparticles 77 3.3 Synthesis nano rGO and nano Si@rGO 79 3.3.1 Synthesis nano rGO 79 3.3.2 Investigate the structure and composition of nano Si@rGO materials 89 3.4 Application of rGO, nano Si and nano Si@rGO materials for fabrication LIB’s anode 92 v 3.4.1 Experimental fabrication anode material combination 92 3.4.2 The electrochemical characteristics of LIB 94 3.5 Conclusion of chapter 105 CONCLUSION 107 LIST OF PUBLICATIONS RELATING TO THESIS 109 LIST OF REFERENCES 110 vi LIST OF FIGURES Pages Figure 1.1 Comparison of energy densities and specific energy of different rechargeable batteries Figure 1.2 Some Li-ion batteries on the white background Figure 1.3 Schematic of the electrochemical process in LIB Figure 1.4 Structures of common cathode materials: 10 Figure 1.5 The model illustrates the formation of host-guest compound .16 Figure 1.6 Schematic picture of the failure mechanism of silicon nanoparticles during cycling .20 Figure 1.7 Schematic process for fabricating the silicon nanoparticles/graphene nanocomposite 21 Figure 1.8 Schematic of silicon synthesis silicon nanoparticles by chemical vapor deposition of silanes 24 Figure 1.9 Schematic of silicon synthesis by electrochemical etching method .25 Figure 1.10 Graphene is the basic structure of other carbon nanostructures 30 Figure 1.11 The bonds of carbon atoms in the graphene 30 Figure 1.12 Image illustrating graphene oxide film 33 Figure 1.13 The thermal reducing reaction of hydroxyl groups 34 Figure 1.14 The thermal reducing reaction of carbonyl groups 34 Figure 2.1 Process of synthesizing silica nanoparticles from rice husk .43 Figure 2.2 Process of synthesizing silicon nano from silica nano 44 Figure 2.3 Schematic diagram of the reduction facility for silicon nanoparticles synthesis process 44 Figure 2.4 rGO synthesis process from graphite 46 Figure 2.5 The thermal reduction process of GO in the furnace 47 Figure 2.6 The synthesis process of nano Si@rGO .48 Figure 2.7 The fabrication process of LIB’s anode 49 Figure 2.8 LIB with the two-electrode structure and glove box 50 Figure 2.9 Cyclic voltammetry waveform 53 vii Figure 2.10 LIB with the two-electrode structure to measure electrochemical characterizations 54 Figure 3.1 TG/DTA curve of rice husk at the heating rate of oC/min 57 Figure 3.2 SiO2 content in rice husk ash dependence on acid treatment time 58 Figure 3.3 SiO2 content in rice husk ash dependence on acid treatment temperature 59 Figure 3.4 SiO2 content in rice husk ash dependence on ratio rice husk/HCl acid 60 Figure 3.5 Influence of calcination temperature on SiO2 content in rice husk ash 62 Figure 3.6 Influence of calcination time on SiO2 content in rice husk ash 62 Figure 3.7 SEM images of rice husk ash samples after calcination at the temperature of 650 oC at the heating rates of 3, 6, 9, 12, 15 oC/min, respective 63 Figure 3.8 SEM and EDX images of nano SiO2 64 Figure 3.9 Particle size distribution of nano SiO2 65 Figure 3.10 XRD pattern of nano SiO2 65 Figure 3.11 SEM image of nano SiO2 sample in high-resolution 66 Figure 3.12: TEM image of nano SiO2 66 Figure 3.13 DSC curves of rice husk pyrolysis process with heating rates of 3, 6, 9, 12, 15 oC/min 67 Figure 3.14 Plots of lg and 1/Tp of RHs of the F-W-O model 68 Figure 3.15 Plots of ln(β/Tp2) and 1/Tp of RHs of the Kissinger model 68 Figure 3.16 DTA curves of rice husk pyrolysis process with heating rates of 3, 6, 9, 12, 15 oC/min 69 Figure 3.17 Plots of lg and 1/Tp of RHs of the F-W-O model 70 Figure 3.18 Plots of ln(β/Tp2) and 1/Tp of RHs of the Kissinger model 70 Figure 3.19 Si content dependence on mol ratio Mg/SiO2 72 Figure 3.20 Si content dependence on calcination temperature 73 Figure 3.21 SEM images of nano Si samples obtained by magnesiothermic reduction of nano SiO2 with heating rates of °C/min and 15 °C/min .74 Figure 3.22 N2 adsorption-desorption isotherms and the pore size distribution of nano Si RH-5 75 viii Figure 3.23 DSC curves of the reaction between nano SiO2 and Mg with different ramp rates 75 Figure 3.24 XRD pattern of nano Si RH-5 76 Figure 3.25 Particle size distribution of nano Si RH-5 76 Figure 3.26 TEM image of nano Si RH-5 77 Figure 3.27 DSC curves of nano SiO2 reduction process with Mg with heating rates of 5, 9, 12, 15 oC/min 77 Figure 3.28 Plots of lg and 1/Tp in the reduction of SiO2 by Mg of the F-W-O model 78 Figure 3.29 Plots of ln(β/Tp2) and 1/Tp in the reduction of SiO2 by Mg of Kissinger model 78 Figure 3.30 GO gel after acid washing .79 Figure 3.31 GO gel after freeze-drying 79 Figure 3.32 Graphite particle size distribution .80 Figure 3.33 GO particle size distribution 80 Figure 3.34 FT-IR spectra of graphite 81 Figure 3.35 FT-IR spectra of GO 81 Figure 3.36 TG/DTA curve of GO at the heating rate of 10 oC/min .83 Figure 3.37 XRD pattern of graphite 83 Figure 3.38 XRD pattern of GO 84 Figure 3.39 SEM image of graphite 84 Figure 3.40 SEM image of GO 85 Figure 3.41 TEM image of GO 85 Figure 3.43 Image of rGO sheets 86 Figure 3.44 rGO powder 86 Figure 3.45 FTIR spectra of rGO 87 Figure 3.46 TG/DTA curve of GO at the heating rate of 10 oC/min .87 Figure 3.47 SEM images of rGO at different resolutions 88 Figure 3.48 XRD pattern of rGO 88 Figure 3.49 EDX pattern of rGO (M1.1) 89 Figure 3.50 EDX pattern of rGO (M2.1) .89 106 - Synthesized rGO, nano Si@rGO and investigated the structure and morphology of rGO, nano Si@rGO materials The C content in the rGO sample is 75.2 %; Si and C content in nano Si@rGO samples were 69.96 % and 31.04 %, respectively - Successfully fabricated LIB with anode on rGO, nano Si and nano Si@rGO basis The specific electrochemical characteristics are as follows: + LIB with anode on rGO basis: Maximum theoretical capacity 372 mAh/g; maximum current density 50C (18600 mAh/g); maximum number of chargedischarge cycles: 100 cycles; Coulombic efficiency: 75 % + LIB with anode on nano Si basis: Maximum theoretical capacity 2250 mAh/g; maximum current density 1C (3800 mAh/g); maximum number of charge-discharge cycles: 35 cycles; Coulombic efficiency: 93 % + LIB with anode on nano Si@rGO basis: Maximum theoretical capacity 1800 mAh/g; maximum current density 5C (13850 mAh/g); maximum number of chargedischarge cycles: 500 cycles; Coulombic efficiency: 98 % 107 CONCLUSION Selected the suitable conditions for the synthesis of nano-silica from the rice husk which is the acid treatment concentration HCl: 10 %, the acid treatment temperature 90 °C, the treatment time hours, the ratio of the rice husk/acid g rice husk/40 ml HCl 10 %, the calcination temperature 650 oC during hours with the heating rate of oC/min The obtained silica nanoparticles have a size of 50-70 nm, the amorphous phase structure and the purity > 99% Determined the thermodynamic and kinetic parameters of synthesizing silica nano from the rice husk: the activation energy of synthesizing silica nano from the rice husk, E* = 126.14 (kJ/mol) (FWO model); E* = 122.6 (kJ/mol) and the exponential factor in the Arrhenius equation is A = 1,033.1010 (Kissinger model), thereby determining the reaction rate constant according to the Arrhenius equation: Determination of thermodynamic parameters of synthesis silica nanoparticles from the rice husk: ∆G * = 138,5 180,4 kJ/mol, ∆H * = 114,9 120,1 kJ/mol ∆S * = -70,9 -61,5 J/mol.K Selected the suitable conditions for the synthesis of silicon nanoparticles from silica nanoparticles with the reducing the agent magnesium: the molar ratio of Mg/SiO2 is 2.1:1, the calcination temperature at 800 oC during hours with the heating rate of oC/min Silicon nanoparticles obtained with the particle size from 30-50 nm, crystal phase structure and the purity > 99% The activation energy of silica reduction process with magnesium: E* = 308.34 (kJ/mol) (F-W-O model); E* = 314.13 (kJ/mol) and the exponential factor in the Arrhenius equation is A = 8.19.1026 (Kissinger model) Synthesized rGO, nano Si@rGO and investigated the structure and morphology of rGO, nano Si@rGO materials The C content in the rGO sample is 75.2 %; Si and C content in nano Si@rGO samples were 69.96 % and 31.04 %, respectively Successfully fabricated LIB with the anode on rGO, nano Si and nano Si@rGO basis The specific electrochemical characteristics are as follows: 108 + LIB with the anode on rGO basis: The maximum theoretical capacity 372 mAh/g; maximum current density 50C (18600 mAh/g); maximum number of chargedischarge cycles: 100 cycles; Coulombic efficiency: 75 % + LIB with the anode on nano Si basis: The maximum theoretical capacity 2250 mAh/g; maximum current density 1C (3800 mAh/g); maximum number of chargedischarge cycles: 35 cycles; Coulombic efficiency: 93 % + LIB with anode on nano Si@rGO basis: Maximum theoretical capacity 1800 mAh/g; maximum current density 5C (13850 mAh/g); maximum number of chargedischarge cycles: 500 cycles; Coulombic efficiency: 98 % The contribution: Determined the conditions to synthesis the silicon nanoparticles from the rice husk Fabricated an anode based on nano Si for the electrochemical characteristics such as the high specific capacity, the high current density and number of chargedischarge cycles, high Coulombic performance Further research directions: Further research on the thermodynamic and kinetic characteristics affecting the synthesis of silicon from nano-silica Further research on the anode fabrication processes based on the synthesis materials, which helps to optimize the anode fabrication process for LIB Further investigate the electrochemical characteristics of an anode made from rGO, nano Si and nano Si @ rGO to get more data about these batteries 109 LIST OF PUBLICATIONS Nguyen Van Thang, Nguyen Manh Tuong, Nguyen Tran Hung (2016), “Thermodynamic evaluation of synthesis of nanosilica from the rice husk”, Proceeding of The 5th Asian materials data symposium, Hanoi 11/2016, pp 331340 Nguyen Van Thang, Nguyen Manh Tuong, Nguyen Tran Hung (2017), “Silicon nanoparticles from the rice husk – thermodynamic evaluation and synthesis”, Vietnam journal of chemistry, 55(3e), pp 176-182 Nguyen Van Thang, Nguyen Manh Tuong, Nguyen Tran Hung (2018), “Characteristic of thermodynamics, kinetics of the process silicon nanoparticle synthesis from rice husk”, Journal of Military Science and Technology, Special Issue CBES2, pp 107-114 Nguyen Van Thang, Nguyen Manh Tuong, Nguyen Tran Hung (2018), “Synthesis and investigate the electrochemical performance of Si/Graphene nanocomposite anode for Lithium-ion batteries”, Vietnam journal of chemistry, 56(4e), pp 168-171 110 LIST OF REFERENCES Vietnamese Le Ha Chi (2012), Fabrication and survey of luminescent, photoelectric and electrochemical properties of nanostructured transition layers, PhD thesis in Physics, Vietnam National University, Hanoi Nguyen Tran Hung, Didier Pribat (2014), “The electrical conductivity of the aluminum thinfilm under lithiation and delithiation in the Lithium-ion batteries”, Vietnam journal of chemistry, The 4th National Conference on Electricization and Application, 52 (6A) Nguyen Tran Hung (2018), Researching technology to fabricate thermal camouflage fabric, application of testing clothes for reconnaissance soldiers, Report on scientific and technological results of the Ministry of Defense theme, Academy of Military Science and Technology Hoang Nham (2006), Inorganic chemistry, Vol 2, Vietnam Education Publishing House, Hanoi Tran Van Nhan, Nguyen Thac Suu, Nguyen Van Tue (1998), Physical chemistry, Vol 2, Vietnam Education Publishing House, Hanoi Tran Van Nhan (2011), Physical chemistry, Vol 3, Vietnam Education Publishing House, Hanoi Nguyen Huu Phu (2006), Physical chemistry and Colloids, Science and Technology Publishing House, Hanoi Huynh Quyen, Truong Hoai Chinh (2012), “Research on the processes of silica recovery from rice husk ash and the general application of additives to highquality cement”, Journal of Science and Technology-The University of Danang, 8(57), pp 8-14 Ngo Quoc Quyen (2004), Storing and converting chemical energy, materials and technology, Set of monographs of the Vietnam Academy of Science and Technology 10 Trinh Xuan Sen (2004), Electrochemistry, Vietnam National University Press, Hanoi 111 11 Tran Son (2001), Chemical kinetics, Science and Technology Publishing House, Hanoi 12 Vu Duc Thao, Nguyen Van Bi, Vu Kiem Thuy (2013), “Study on recovering cobalt from waste Li-ion batteries of mobile phones”, Journal of Science and Technology, Vietnam Academy of Science and Technology, 51(3B), pp 280286 13 Nguyen Tien Tai (2008), The thermal analysis applied in material research, Science and Technology Publishing House, Hanoi 14 Nguyen Tien Tai (2012), Research on new generation technology of biofuel production from rice husk by pyrolysis method on fluidized bed reactor, Report results of scientific and technological topic, Vietnam Academy of Science and Technology 15 Nguyen Manh Tuong (2017), Carbon nanotube: manufacturing method and applicability in the military, Science and Technology Publishing House, Hanoi English 16 A A Ariea, O M Vovk (2010), “Surface-Coated Silicon Anodes with Amorphous Carbon Film Prepared by Fullerene C60 Sputtering”, J Electrochem Soc., 157 (6), A660-A665 17 A Fojtik, M Giersig, and Henglein (1993), “Formation of Nanometer-size Silicon Nanoparticles in a Laser Induced Plasma in SiH4”, J Physics and Chemistry, No 11, pp 1493-1496 18 A Gohier, B Laik, K.-H Kim, J.-L Maurice, J.-P Pereira-Ramos, C S Cojocaru and P Tran Van (2012), “High-Rate Capability Silicon Decorated Vertically Aligned Carbon Nanotubes for Li-Ion Batteries”, Adv Mater., Vol 24, pp 2592-2597 19 A H Castro Neto, F Guinea, N M R Peres, K S Novoselov and A K Geim (2009), “The electronic properties of graphene”, Reviews of modern physics, Vol 81 20 A K Shukla and T Prem Kumar (2008), “Materials for Next Generation Lithium Batteries”, Current Science, Vol 94 (3), pp 317-327 112 21 A M Chockla, J T Harris, V A Akhavan, T D Bogart, V C Holmberg, C Steinhagen, C B Mullins, K J Stevenson and B A Korgel (2011), “Silicon nanowire fabric as a lithium ion battery electrode material”, J Am Chem Soc., 133 (51), pp 20914-20921 22 A Magasinski, B Zdyrko, I Kovalenko, B Hertzberg, R Burtovyy, C F Huebner, T F Fuller, I Luzinov, G Yushin (2010), “Toward Efficient Binders for Li-Ion Battery Si-Based Anodes: Polyacrylic Acid”, ACS Appl Mater Interfaces, 2, pp 3004-3010 23 Aurbach D., M.B., Weissman I., Levi E., Ein-Eli Y., (1999), “On the correlation between surface chemistry and performance of graphite negative electrodes for Li ion batteries”, Electrochimica Acta, 45, pp 67-86 24 Aurbach Doron, Z.E., Cohen Yaron, Teller Hanan, (2002), “A short review of failure mechanisms of lithium metal and lithiated graphite anodes in liquid electrolyte solutions”, Solid State Ionics, 148, pp 405-416 25 Bao, Z et al (2007), “Chemical reduction of three-dimensional silica microassemblies into microporous silicon replicas”, Nature, 446, pp 172-175 26 C K Chan, H L Peng, G Liu, K McIlwrath, X F Zhang, R A Huggins and Y Cui (2008), “High-performance lithium battery anodes using silicon nanowires”, Nat Nanotechnol., Vol (1), pp 31-35 27 C Martin, O Crosnier, R Retoux, D Belanger, D M Schleich, T Brousse (2011), “Chemical coupling of carbon nanotubes and silicon nanoparticles for improved negative electrode performance in lithium - ion batteries”, Adv Funct Mater., 21, pp 3524-3530 28 Caterina Soldano, Ather Mahmood, Erik Dujardin (2010), “Production, properties and potential of graphene”, Carbon, Vol 48 (8), pp 2127-2150 29 Chan C.K., P.H., Liu G., Mcilwrath K., Zhang X.F., Huggins R.A and Cui Y (2008), “High-performance lithium battery anodes using silicon nanowires”, Nature nanotechnology, 3, pp 31-35 30 Changjing Fu, Chunlai Song, Lilai Liu, Weiling Zhao, Xuedong Xie (2016), “High Reversible Silicon/Graphene Nanocomposite Anode for Lithium-Ion Batteries”, Int J Electrochem Sci., 11, pp 154-164 113 31 Croce F., D.E.A., Hassoun J., Reale P., Scrosati B (2003), “Advanced electrolyte and electrode materials for lithium polymer batteries”, Journal of Power Sources, Vol 119-121, pp 399-402 32 D S M Iaboni and M N Obrovac (2016), “Li15Si4 Formation in Silicon Thin Film Negative Electrodes”, Journal of the Electrochemical Society, 163 (2), A255-A261 33 David Linden, Thomas B Reddy (2002), Handbook of batteries, McGrawHill, NewYork 34 F X Chen, C R Zhou and G P Li (2012), “Study on Thermal Decomposition and the Non-Isothermal Decomposition Kinetics of Glyphosate”, Journal of Thermal Analysis and Calorimetry, Vol 109 (3) , pp 1457-1462 35 G Derrien, J.H., S Panero and B Scrosati (2007), “Nanostructured Sn–C Composite as an Advanced Anode Material in High-Performance Lithium-Ion Batteries”, Advanced Materials, 19 (17), pp 2336-2340 36 G K Simon, B Maruyama, M F Durstock, D J Burton and T Goswami (2011), “Silicon-coated carbon nanofiber hierarchical nanostructures for improved lithium-ion battery anodes”, J Power Sources, Vol 196 (23), pp 10254-10257 37 G Liu, S D Xun, N Vukmirovic, X Y Song, P Olalde-Velasco, H H Zheng, V S Battaglia, L W Wang, W L Yang (2011), “Polymers with tailored electronic structure for high capacity lithium battery electrodes”, Adv Mater., 23 (40), pp 4679-4683 38 Guanghui Yuan, Gang Wang, Hui Wang, Jintao Bai (2016), “Half-cell and full-cell investigations of 3D hierarchical MoS2/graphene composite on anode performance in lithium-ion batteries”, Journal of Alloys and Compounds, 660, pp 62-72 39 H Chen, Z Dong, Y Fu and Y Yang (2010), “Silicon nanowires with and without carbon coating as anode materials for lithium-ion batteries”, J Solid State Electrochem., Vol 14, pp 1829-1834 40 H E Kissinger (1956), “Variation of Peak Temperature with Heating Rate in Differential Thermal Analysis”, Journal of Research of the National Bureau of Standards, Vol 57 (4), pp 217-221 114 41 H Kim and J Cho (2008), “Superior Lithium Electroactive Mesoporous Si@Carbon Core−Shell Nanowires for Lithium Battery Anode Material”, Nano Lett., Vol 8, pp 3688-3691 42 Hung T Nguyen, F Yao, M R Zamfir, C Biswas, K P So, Y H Lee, S M Kim and D Pribat (2011), “Highly Interconnected Si Nanowires for Improved Stability Li‐Ion Battery Anodes”, Adv Energy Mater., Vol 1, pp 1154-1161 43 Hung T Nguyen, M R Zamfir, L D Duong, Y H Lee, P Bondavalli and D Pribat (2012), “Alumina-coated silicon-based nanowire arrays for high quality Li-ion battery anodes”, J Mater Chem., Vol 22, pp 24618-24626 44 J Bae (2011), “Fabrication of carbon microcapsules containing silicon nanoparticles–carbon nanotubes nanocomposite by sol–gel method for anode in lithium ion battery”, J Solid State Chem., 184, pp 1749-1755 45 J K Lee, K B Smith, C M Hayner, H H Kung (2010), “Silicon nanoparticles-graphene paper composites for Li-ion battery anodes”, Chem Commun., 46 (12), pp 2025-2027 46 J Park, G.-P Kim I Nam, S Park, J Yi (2013), “One-pot synthesis of silicon nanoparticles trapped in ordered mesoporous carbon for use as an anode material in lithium-ion batteries”, Nanotechnology, 24, 025602 47 J S Bridel, T Azais, M Morcrette, J M Tarascon, D Larcher (2010), “Key Parameters Governing the Reversibility of Si/Carbon/CMC Electrodes for LiIon Batteries”, Chem Mater., 22, pp 1229-1241 48 J Vetter, P Novak, M.R Wagner (2005), “Aging Mechanisms in Lithiumion Batteries”, Journal of Power Sources, 147, pp 269-281 49 James G Radich, P.J.M., and Prashant V Kamat (2011), “Graphene-based Composites for Electrochemical Energy Storage”, The Electrochemical Society Interface, pp 63-66 50 Jean-Noel Fuchs, Mark Oliver Goerbig (2008), Introduction to the Physical Properties of Graphene, Lecture Notes, Cours Graphene 51 Jianbiao Chen, Yanhong Wang, Xuemei Lang, Xiu'e Ren, Shuanshi Fan (2017), “Evaluation of agricultural residues pyrolysis under non-isothermal 115 conditions: Thermal behaviors, kinetics, and thermodynamics”, Bioresource Technology, 241, pp 340-348 52 Jung-In Lee, Nam-Soon Choi and Soojin Park (2012), “Highly stable Sibased multicomponent anodes for practical use in lithium-ion batteries”, Energy Environ Sci., 5, pp 7878-7882 53 K Andre Mkhoyan, Alexander W Contryman, John Silcox, Derek A Stewart, Goki Eda, Cecilia Mattevi, Steve Miller, and Manish Chhowalla (2009), “Atomic and Electronic Structure of Graphene-Oxide”, Nano Letters, Vol.9 (3), pp 1058-1063 54 K Mizushima, P.C Jones, P.J Wiseman, J.B Goodenough (1981), “A new cathode material for batteries of high energy density”, Solid State Ionics, Vol 4, pp 171-174 55 Kaiserberger E., Opfermann J (2003), Model-free methods of kinetic analysis and simulations, NETZSCH-Geratebau GmbH, Germany 56 Khu Le Van, Thu Thuy Luong Thi (2016), “Actived carbon prepared from rice husk: Nitric acid modification and BTX adsorption”, Elixir Materials Science, 93, pp 39362-39366 57 L.-F Cui, R Ruffo, C K Chan, H Peng and Y Cui (2009), “Crystallineamorphous core-shell silicon nanowires for high capacity and high current battery electrodes”, Nano Lett., Vol (1), pp 491-495 58 L.-F Cui, Y Yang, C.-M Hsu and Y Cui (2009), “Carbon−Silicon Core−Shell Nanowires as High Capacity Electrode for Lithium Ion Batteries”, Nano Lett., Vol 9, pp 3370-3374 59 Le Dinh Trong, Pham Duy Long, Nguyen Nang Dinh (2008), Fabrication of ion conductive materials La0.67-xLi3xTiO3 used as electrolyte for all solid Li+ ion batteries, Reports of the Eleventh Vietnamese-German Seminar on Physics and Engieering (VGS 11), Hanoi, Vietnam 60 Le Van Hai et al (2013), “Synthesis of silica nanoparticles from Vietnamese rice husk by sol–gel method”, Nanoscale Research Letters 116 61 Li Zhang, Mingxing Huang, Cairong Zhou (2013), “Thermal stability and decomposition kinetics of polysuccinimide”, American Journal of Analytical Chemistry, 4, pp 749-755 62 Liangliang Cao, Tyler P Price, Michael Weiss, and Di Gao (2008), “Super Water- and Oil-Repellent Surfaces on Intrinsically Hydrophilic and Oleophilic Porous Silicon Films”, Langmuir, 24 (5), pp 1640-1643 63 Liangming Wei, Changxin Chen, Zhongyu Hou & Hao Wei (2016), “Poly (acrylic acid sodium) grafted carboxymethyl cellulose as a high performance polymer binder for silicon anode in lithium ion batteries”, Scientific Reports, 6:19583|DOI: 10.1038/srep19583, www.nature.com/scientificreports 64 Lin D., Liu Y., Cui Y (2017), “Reviving the lithium metal anode for highenergy batteries”, Nat Nanotechnol., 12 (3), pp 194-206 65 Marca M.Doeff (2013), Batteries for Sustainability: Selected Entries from the Encyclopedia of Sustainability Science and Technology, Chapter 2, Springer Science and Business Media, New York, USA 66 Mihai Robert Zamfir, Hung Tran Nguyen, Eric Moyen, Young Hee Lee and Didier Pribat (2013), “Silicon nanowires for Li-based battery anodes: a review”, Journal of Materials Chemistry A, 1, pp 9566-9586 67 Mohammed Abdillah Ahmad Farid, Mohd Ali Hassan, Yun Hin Taufiq-Yap et al (2018), “Kinetic and thermodynamic of heterogeneously K3PO4/AC-catalysed transesterification via pseudo-first order mechanism and Eyring-Polanyi equation”, The science and technology of fuel and energy, 232, pp 653-658 68 Nagamori, M., Malinsky, I & Claveau A (1986), “Thermodynamics of the silicon-carbonoxygen system for the production of silicon carbide and metallic silicon”, Metall Trans B, 17, pp 503–514 69 Nguyen T.T.H, Nguyen T.H (2015), “Synthesis of graphene oxide as a hightemperature fluid-loss-control additive in water-based drilling fluids from Vietnamese graphite”, PetroVietnam Journal, 8, pp 41-50 117 70 Nguyen Thi Thu Huyen et al (2017), “Preparation and characterization of porous carbon from rice husk applied for electrode materials”, Vietnam Journal of Science and Technology, 55 (5B), pp 279-286 71 Nian Liu, Kaifu Huo, Matthew T McDowell, Jie Zhao & Yi Cui (2013), “Rice husks as a sustainable source of nanostructured silicon for high performance Li-ion battery anodes”, Sci Rep., 3:1919 doi: 10.1038/srep01919 72 Nobuyoshi Koshida, Nobuo Matsumoto (2003), “Fabrication and quantum properties of nanostructured silicon”, Materials science and engineering, 40, pp 169-205 73 Peter G Bruce, Bruno Scrosati, and J.-M Tarascon (2008), “Nanomaterials for Rechargeable Lithium Batteries”, Angewandte Chemie International Edition, 47, pp 2930-2946 74 Prof S Shippy and M-J Lu (2007), Cyclic Voltammetry An Example of Voltaic Methods, ebooks library 75 Raymond Jasinski (1971), High-energy Batteries, Plenum Preess, New York, USA 76 Rogers R N., Smith L C (1970), “Application of scanning calorimetry to the study of chemical kinetics”, Thermochimica Acta, Vol (1), pp 1-9 77 Samuel P Kounaves (1997), Voltammetric Techniques, Handbook of Instrumental Techniques for Analytical Chemistry, Tufts University, Chapter 37 78 Sasha Stankovich, Dmitriy A Dikin, Geoffrey H B Dommett, Kevin M Kohlhaas, Eric J Zimney, Eric A Stach, Richard D Piner, Son Binh T Nguyen & Rodney S Ruoff (2006), “Graphene-based composite materials”, Nature, 442, pp 282-286 79 Schalkwijk W A Van and Scrosati B., (2002), Advances in Lithium-ion Batteries, Kluwer Academic/Plenum Publishers, New York 80 S.K Das, S.D., AJ Bhattacharyya (2010), “High lithium storage in micrometre sized mesoporous spherical self-assembly of anatase titania nanospheres and carbon”, Journal of Materials Chemistry, 20 (8), pp 1600-1606 118 81 T H Hwang, Y M Lee, B.-S Kong, J.-S Seo, J W Choi (2012), “Electrospun core-shell fibers for robust silicon nanoparticle-based lithium ion battery anodes”, Nano Lett., 12 (2), pp 802-807 82 T Richard Jow, Kang Xu, Oleg Borodin and Makoto Ue (2014), Electrolytes for Lithium and Lithium-Ion Batteries, Vol 58, Springer Science and Business Media, New York, USA 83 T Tsumura, N Kojitani, I Izumi, N Iwashita, M Toyoda; M Inagaki (2002), “Carbon coating of anatase-type TiO2 and photoactivity”, J Mater Chem.,12, pp 1391–1396 84 T Song, J Xia, J.-H Lee, D H Lee, M.-S Kwon, J.-M Choi, J Wu, S K Doo, H Chang, W I Park, D S Zang, H Kim, Y Huang, K.-C Hwang, J A Rogers, U Paik (2010), “Array of scaled silicon nanotubes as anodes for lithium ion batteries”, Nano Lett., 10, pp 1710-1716 85 V S Aigbodion, S B Hassan, C U Atuanya (2012), “Kinetics of isothermal degradation studies by thermogravimetric data: effect of orange peels ash on thermal properties of high density polyethylene (HDPE)”, J Mater Environ Sci., (6), pp 1027-1036 86 Sundaram Ramukutty, Esakki Ramachandran (2014), “Reaction rate models for the thermal decomposition of ibuprofen crystals”, Journal of crystallization process and technology, Vol (2), pp 71–78 87 W Wang and P N Kumta (2010), “Nanostructured hybrid silicon/carbon nanotube heterostructures: reversible high-capacity lithium-ion anodes”, ACS Nano, Vol (4), pp 2233-2241 88 Wakihara M and Kodansha O Yamamato (1998), Lithium Ion Batteries, Wiley, Tokyo, Japan 89 Wang G., Ahn J., Yao J., Bewlay S., Liu H (2004), “Nanostructured Si-C composite anodes for lithium-ion batteries”, Electrochem Commun., 6, pp 689-692 90 Wu H.; Chan G., Choi J.W., Ryu I., Yao Y., McDowell M.T., Lee S.W., Jackson A., Yang Y., Hu L (2012), “Stable cycling of double-walled silicon 119 nanotube battery anodes through solid–electrolyte interphase control”, Nat Nanotechnol., (5), pp 310-315 91 X H Liu, L Qiang Zhang, L Zhong, Y Liu, H Zheng, J W Wang, J.-H Cho, S A Dayeh, S T Picraux, J P Sullivan, S X Mao, Z Z Ye and J Y Huang (2011), “Anisotropic swelling and fracture of silicon nanowires during lithiation”, Nano Lett., Vol 11 (8), pp 2251-2258 92 X Zhao, C M Hayner, M C Kung, H H Kung (2011), “In‐Plane Vacancy‐Enabled High‐Power Si–Graphene Composite Electrode for Lithium‐Ion Batteries”, Adv Energy Mater., Vol (6), pp 1079-1084 93 X Zhou, Y.-X Yin, L.-J Wan, Y.-G Guo (2012), “Self‐Assembled Nanocomposite of Silicon Nanoparticles Encapsulated in Graphene through Electrostatic Attraction for Lithium‐Ion Batteries”, Adv Energy Mater., Vol (9), pp 1086-1090 94 Xiang, H.; Zhang, K.; Ji, G.; Lee, J.Y.; Zou, C.; Chen, X.; Wu, J (2011), “Graphene/nanosized silicon composites for lithium battery anodes with improved cycling stabilit”, Carbon, 49, pp 1787–1796 95 Xin, X.; Zhou, X.; Wang, F.; Yao, X.; Xu, X.; Zhu, Y.; Liu, Z A (2012), “3D porous architecture of Si/graphene nanocomposite as high-performance anode materials for Li-ion batteries”, J Mater Chem., 22, pp 7724–7730 96 Y Liu, H Zheng, X H Liu, S Huang, T Zhu, J Wang, A Kushima, N S Hudak, X Huang, S Zhang, S X Mao, X Qian, J Li and J Y Huang (2011), “Lithiation-induced embrittlement of multiwalled carbon nanotubes”, ACS Nano, Vol 5, pp 7245-7253 97 Y Oumellal, N Delpuech, D Mazouzi, N Dupre, J Gaubicher, P Moreau, P Soudan, B Lestriez, D Guyomard (2011), “The failure mechanism of nanosized Si-based negative electrodes for lithium ion batteries”, J Mater Chem., 21, 6201-6208 98 Yao, Y.Q.; Cen, Y.J.; Sisson, R.D.; Liang, J.Y A (2016), “Synthesize Protocol for Graphene Nanosheets”, In Proceedings of the 4th Asia Conference on Mechanical and Materials Engineering, Kuala Lumpur, Malaysia, pp 3–6 99 Yemeserach Mekonnen, Aditya Sundararajan, Arif I Sarwat (2017), “A Review of Cathode and Anode Materials for Lithium-Ion Batteries”, J SoutheastCon., pp 1-6 120 100 Yi Lu, Tao Wang, Zhaojun Tian, Qing Ye (2017), “Preparation of Graphene Oxide Paper as an Electrode for Lithium-Ion Batteries Based on a Vacuum Filtration Method”, Int J Electrochem Sci., 12, pp 8944 – 8952 101 Yanhong Wang, Yaoping Liu, Jieyun Zheng, Hao Zheng, Zengxia Mei, Xiaolong Du and Hong Li (2013), “Electrochemical performances and volume variation of nano-textured silicon thin films as anodes for lithium-ion batteries”, Nanotechnology, 24, 424011 102 Ye, Y.-S.; Xie, X.-L.; Rick, J.; Chang, F.-C.; Hwang, B.-J (2014), “Improved anode materials for lithium-ion batteries comprise non-covalently bonded graphene and silicon nanoparticles”, J Power Sources, 247, pp 991–998 103 Yinjie Cen, Richard D Sisson, Qingwei Qin and Jianyu Liang (2018), “Current progress of Si/graphene nanocomposites for lithium-ion batteries”, Review, Journal of Carbon Research, Vol (18), pp 1-14 104 Yoo E, K.J., Hosono E, Zhou HS, Kudo T, Honma I (2008), “Large reversible Li storage of graphene nanosheet families for use in rechargeable lithium ion batteries”, Nano Lett., Vol 8, pp 2277–2282 105 Z.-L Xu, B Zhang and J.-K Kim (2014), “Electrospun carbon nanofiber anodes containing monodispersed Si nanoparticles and graphene oxide with exceptional high rate capacities”, Nano Energy, 6, pp 27-35 ... synthesis silica nanoparticles from rice husk 67 3.2 Synthesis of silicon nanoparticles from silica nanoparticles 72 3.2.1 Investigation of factors affecting silicon nanoparticles... synthesizing silica nanoparticles from rice husk .43 Figure 2.2 Process of synthesizing silicon nano from silica nano 44 Figure 2.3 Schematic diagram of the reduction facility for silicon nanoparticles... silicon nanoparticles and experimental conditions for the synthesis of silicon nano from rice husk; rGO, nano Si@rGO The LIB’s anode is fabricated on the basis of silicon nanoparticles, rGO, nano