LX470 quy trinh dang ky chia dieu khien tu xa

BE–119 BODY ELECTRICAL – WIRELESS DOOR LOCK CONTROL SYSTEM WIRELESS DOOR LOCK CONTROL SYSTEM BE2GM–01 REGISTRATION PROCEDURE HOW TO CODE REGISTRATION NOTICE: When replacing the theft deterrent ECU or transmitter, registration of recognition code is necessary because they are provided as a single components (a) Select the operation mode S Add mode S Rewrite mode S Prohibition mode S Confirmation mode HINT: S The ”Add mode” is for adding new recognition codes while retaining the already registered codes This mode is used when the transmitter is added When the number of the registered codes exceeds codes, the previously registered codes will be erased in order, staring from the first registered code S The ”Rewrite mode” is for erasing all the registered codes and registering newly recognized codes only This mode is used when the transmitter or the door control receiver is replaced S The ”Prohibition mode” is for erasing all the registered codes to prohibit the wireless door lock operation This mode is used when the transmitter is lost S The ”Confirmation mode” is for confirming the number of recognition codes that are registered This mode is used to check the number of registered codes when new codes are added to the registration, etc (b) Follow the chart on the following page to register the transmitter recognition code to the theft deterrent ECU HINT: S When procedure is outside the specification, the registration operation is cancelled S Maximum of recognition codes can be registered BE–120 BODY ELECTRICAL (c) – WIRELESS DOOR LOCK CONTROL SYSTEM By LEXUS Hand–Held Tester START The vehicle should be in the following conditions: D Ignition switch is ON Hand–held tester operation: Select ”L/C 100” from the menu Select ”TDS” (Theft Deterrent System) Select ”WIRELESS REGISTRATION” After the above operations, proceed to the succeeding operations according to the prompts on the tester screen Transmitter SW Operation: HINT: Perform this operation during the countdown screen Press both lock and unlock SW (Between and 1.5 sec.) Within sec Press any one of SW (For more than sec.) This wireless buzzer sounds when the registration is completed normally HINT: Select the next step on the tester screen Continue the registration Register other transmitters? Or Finish the registration? Finish the registration END HINT: This page is to show the registration procedure briefly using the hand–held tester For detailed procedures, please refer to the prompts on the tester screen The number of currently registered codes can be checked out on the first screen of the WIRELESS REGISTRATION BE–121 BODY ELECTRICAL (d) – WIRELESS DOOR LOCK CONTROL SYSTEM By Switch Operation: HINT: The registration operation is cancelled if each operation is not completed within the specified time START The vehicle should be in the following conditions: D Driver door is open (Other doors are closed) D No key is inserted in the IG key cylinder Within sec Insert and remove the key into/from the ignition cylinder twice Insert→remove →insert→remove Within 40 sec Close and open the driver door twice Close→open→close→open Insert and remove the key into/from the ignition cylinder once Insert→remove Within 40 sec Close and open the driver door twice Close→open→close→open Insert the key into the ignition key cylinder Close all the doors Within 40 sec Mode Selection Add mode Turn the IG SW ON ←→LOCK once Rewrite mode Turn the IG SW ON ←→LOCK twice HINT: If the IG switch operation is not performed with the specified number of times (If it is times, times or more), this operation is finished with no response Confirmation mode Turn the IG SW ON ←→LOCK times Remove the key from the IG key cylinder Prohibition mode Turn the IG SW ON ←→LOCK times BE–122 BODY ELECTRICAL – WIRELESS DOOR LOCK CONTROL SYSTEM Response of whether or not being moved to each mode is indicated by the number of times of door lock working (lock/unlock) D Add mode: D Rewrite mode: D Confirmation mode: Within sec D Prohibition mode: once*1 twice*1 The number of times equivalent to the number of currently registered codes*2 times*1 HINT: The confirmation mode and the prohibition mode are finished after the responses Confirmation mode Prohibition mode Add mode, Rewrite mode Within 40 sec END Transmitter SW Operation: Press both lock and unlock SW (Between and 1.5 sec.) Within sec Press any one of SW (For more than sec.) Within sec Response of whether or not the registration is completed is indicated the number of times of door lock operations (lock/unlock operation) When registration is completed: once*1 When registration is not completed: twice*1 Continue the registration Within 40 sec Register other transmitters? or Finish the registration? Finish the registration Perform one of the following operations to finish the Add mode and the Rewrite mode D Insert the key into the IG key cylinder D Open any one of the doors D Wait for 40 sec after the code registration HINT: When registering codes at a time, the mode will be finished when the 4th code is registered BE–123 BODY ELECTRICAL – WIRELESS DOOR LOCK CONTROL SYSTEM HINT: Operation cycle of the door lock (lock/unlock operation) LOCK *1: Door Lock Motor UNLOCK Sec Sec LOCK *2: Door Lock Motor UNLOCK Sec Sec 02−1 PREPARATION − AUTOMATIC TRANSMISSION / TRANSAXLE AUTOMATIC TRANSMISSION / TRANSAXLE 021YU−01 PREPARATION SST 09223−15020 Oil Seal & Bearing Replacer AUTOMATIC TRANSMISSION ASSY(A750E/A750F) 09226−10010 09308−00010 Crankshaft Front & Rear Bearing AUTOMATIC Replacer ASSY(A750E/A750F) TRANSMISSION Oil Seal Puller AUTOMATIC TRANSMISSION ASSY(A750E/A750F) 09320−89010 09350−30020 Transfer Clutch Spring CLUTCH DRUM & INPUT SHAFT Compressor ASSY(A750E/A750F) TOYOTA Automatic Transmission AUTOMATIC Tool Set ASSY(A750E/A750F) TRANSMISSION OIL PUMP ASSY(A750E/A750F) CLUTCH DRUM & INPUT SHAFT ASSY(A750E/A750F) (09350−07020) Oil Pump Puller AUTOMATIC TRANSMISSION ASSY(A750E/A750F) (09350−07040) No.2 Piston Spring Compressor CLUTCH DRUM & INPUT SHAFT ASSY(A750E/A750F) (09350−07050) No.3 Piston Spring Compressor AUTOMATIC TRANSMISSION ASSY(A750E/A750F) (09350−07060) No.1 Snap Ring Expander AUTOMATIC TRANSMISSION ASSY(A750E/A750F) (09350−07070) No.2 Snap Ring Expander AUTOMATIC TRANSMISSION ASSY(A750E/A750F) CLUTCH DRUM & INPUT SHAFT ASSY(A750E/A750F) (09350−07080) Brake Reaction Sleeve Puller AUTOMATIC TRANSMISSION ASSY(A750E/A750F) (09350−07090) Brake No.1 Piston Puller AUTOMATIC TRANSMISSION ASSY(A750E/A750F) A750E, A750F A/T REPAIR MANUAL (RM999U) 02−2 PREPARATION (09350−07110) − AUTOMATIC TRANSMISSION / TRANSAXLE Oil Seal Replacer AUTOMATIC TRANSMISSION ASSY(A750E/A750F) (09351−32140) 09387−00070 Oil Seal Replacer OIL PUMP ASSY(A750E/A750F) First & Reverse Brake Wrench CLUTCH DRUM & INPUT SHAFT ASSY(A750E/A750F) 09710−30050 Suspension Arm Bushing Replacer AUTOMATIC TRANSMISSION ASSY(A750E/A750F) 09950−70010 Handle Set AUTOMATIC TRANSMISSION ASSY(A750E/A750F) (09951−07100) Handle 100 AUTOMATIC TRANSMISSION ASSY(A750E/A750F) Recomended Tools 09031−00030 Pin Punch AUTOMATIC TRANSMISSION ASSY(A750E/A750F) Equipment Feeler gauge Cylinder Gauge Vernier calipers Dial indicator Micrometer Feeler gauge Straight edge Torque wrench Angle gauge V block A750E, A750F A/T REPAIR MANUAL (RM999U) 02−3 PREPARATION − AUTOMATIC TRANSMISSION / TRANSAXLE Lubricant Automatic transmission fluid (LAND CRUISER/ LX470) Dry fill (2UZ−FE w oil cooler) Drain and refill (2UZ−FE w oil cooler) 11.6 liters (12.3 US qts, 10.2 Imp qts) 3.0 liters (3.2 US qts, 2.6 Imp qts) Automatic transmission fluid (LAND CRUISER) Dry fill (1HD−FTE w oil cooler) Drain and refill (1HD−FTE w oil cooler) 12.1 liters (12.8 US qts, 10.6 Imp qts) 3.0 liters (3.2 US qts, 2.6 Imp qts) Automatic transmission fluid (LAND CRUISER/ LX470) Dry fill (2UZ−FE w/o oil cooler) Drain and refill (2UZ−FE w/o oil cooler) 10.8 liters (11.4 US qts, 9.5 Imp qts) 3.0 liters (3.2 US qts, 2.6 Imp qts) Automatic transmission fluid (LAND CRUISER) Dry fill (1HD−FTE w/o oil cooler) Drain and refill (1HD−FTE w/o oil cooler) 11.4 liters (12.0 US qts, 10.0 Imp qts) ATF TYPE T−IV or equivalent ATF TYPE T−IV or equivalent ATF TYPE T−IV or equivalent ATF TYPE T−IV or equivalent 3.0 liters (3.2 US qts, 2.6 Imp qts) Automatic transmission fluid (4RUNNER,GX470) Dry fill Drain and refill 11.1 liters (11.7 US qts, 9.8 Imp qts) 3.0 liters (3.2 US qts, 2.6 Imp qts) ATF TYPE T−IV or equivalent SSM (Special Service Materials) 08826−00090 ”Seal Packing 1281,” AUTOMATIC THREE BOND 1281 or equivalent ASSY(A750E/A750F) (FIPG) A750E, A750F A/T REPAIR MANUAL (RM999U) TRANSMISSION Ref No : Page : M 19 of REGISTRATION OF ADDITIONAL MASTER KEY S Perform this operation to register an additional master key S It is possible to register up to master key codes including the already registered key codes S When any operation time described below is over, registration mode completes S When the next procedure is performed while the timer is working, the timer completes counting time, then next timer starts Initial condition: All door closed, not key in cylinder Start Insert already registered master key into the key cylinder Within 15 secs Repeatedly turn the key from ignition switch LOCK to ON times Repeat driver’s door open/close operation times Within 20 secs Remove the master key Within 10 secs Insert the key to be registered into the key cylinder Keep ignition switch at ON position for 60 secs or more Within 10 secs Within 10 secs More than 60 secs Remove the key from the key cylinder Yes Will you register the next key? No Leave the vehicle more than 10 sec without any operation (Only Corolla (WZE110) ) Open and close a driver’s door End Author : Date : Ref No : Page : S S S S S 26 of ADDITIONAL REGISTRATION OF SUB KEY Perform this operation to register an additional sub key It is possible to register up to sub key codes including the already registered key code When any operation time described below is over, registration mode completes When the next procedure is performed while the timer is working, the timer completes counting time, then next timer starts Initial condition: All doors closed, not key in cylinder Start Insert already registered master key into the key cylinder Repeatedly turn the key from ignition switch LOCK to ON times Repeat driver’s door open/close operation times Within 20 secs Remove the master key Within 10 secs Insert the key to be registered into the key cylinder Within 10 secs Keep ignition switch at ON position for 60 secs or more Within 10 secs Within 15 secs More than 60 secs Remove the key from the key cylinder Yes Will you register the next key? No Leave the vehicle more than 10 sec without any operation (Only Corolla (WZE110) ) Open and close a driver’s door End Author : Date : Ref No : Page : E 34 of 4 ERASURE OF TRANSPONDER KEY CODE S Perform this operation to erase transponder key registration from the transponder key ECU S Delete all other master and sub key codes leaving the master key code to use the operation When using the key which was used before deletion, it is necessary to register the code again S When any operation time described below is over, registration mode completes S When the next procedure is performed while the timer is working, the timer completes counting time, then next timer starts Initial condition: All doors closed, not key in cylinder Start Insert already registered master key into the key cylinder Within 15 secs Repeatedly turn the key from ignition switch LOCK to ON times Repeat driver’s door open/close operation times Within 20 secs Remove the master key End Author : Date : BE−177 BODY ELECTRICAL (a) OFF BE02R−04 TRANSPONDER KEY ECU INPUT CONDITION DISPLAY READ CODE Connect the positive (+) lead from the volt meter (Analog Type) to OP3 of the check connector and the negative (−) lead to E1 of the check connector OP1 Iei−23−1 0.5 sec ON ENGINE IMMOBILISER SYSTEM (Except 2UZ−FE) PRE−CHECK Check Connector E1 − I01825 1.5 sec Example 2.5 sec Code 11 4.5 sec Code 21 I01826 (b) Insert the ignition key in the key cylinder (c) Read the code from the movement of the tester needle If no code is output, turn the ignition switch ON If a code is now output, check if the DOME fuse is blown HINT: S The code can be read using a luminous diode (Recommend activation current 10 − 20 mA) instead of a tester S A digital tester can also be used Display condition: S When there are multiple codes, they are output in order staring from the lowest code S After all the codes are output, Lo is displayed for 4.5 secs., then all the code are output again starting from the lowest code S If the situation changes during code output, Lo is output for 4.5 secs after output of the current code ceases, then the codes are output again starting from the lowest code E.g while 11 (out of 11 and 21) is being output, conditions change and 12 is added So after 11 is output, Lo is output for 4.5 secs., then 11, 12 and 21 are output BE−178 BODY ELECTRICAL − ENGINE IMMOBILISER SYSTEM (Except 2UZ−FE) TRANSPONDER KEY ECU INPUT CONDITION DISPLAY CODE LIST Gasoline engine: Code Output condition 11 Key unlock warning switch ON (Ignition key inserted) 12 Any door is open (Door courtesy switch ON) 13 Ignition switch at ON position 21 Master key is inserted in key cylinder and the immobiliser system is OFF 22 Sub key is inserted in key cylinder and immobiliser system is OFF 31 Key code recorded in transponder key ECU differs from code of key inserted in key cylinder 32 Transponder key code cannot be read 33 Key code cannot be read because format of chip inside key is wrong 34 Transponder key ECU has no memory space to register key code 41 Recognition code is normal and the immobiliser system is OFF Diesel engine: Code Output condition 11 Key unlock warning switch ON (Ignition key inserted) 12 Any door is open (Door courtesy switch ON) 13 Ignition switch at ON position 21 Master key is inserted in key cylinder and the immobiliser system is OFF 22 Sub key is inserted in key cylinder and immobiliser system is OFF 31 Key code recorded in transponder key ECU differs from code of key inserted in key cylinder 32 Transponder key code cannot be read 33 Key code cannot be read because format of chip inside key is wrong 34 Transponder key ECU has no memory space to register key code 51 FCVC code is learned 52 FCVC is unlocked 53 FCVC code is error 54 FCVC is check−sum error 55 FCVC is factory code initialling 56 FCVC code line trouble 57 FCVC trouble 58 While ignition switch ON, no response from FCVC for consecutive sec, BE−179 BODY ELECTRICAL − ENGINE IMMOBILISER SYSTEM (Except 2UZ−FE) TRANSPONDER KEY ECU INPUT CONDITION DISPLAY MALFUNCTION LIST Symptom Cause No code is output DOME Fuse Wire harness or connector Transponder key ECU Even when key is inserted in key cylinder, Code 11 is not output Key unlock warning switch Wire harness or connector Transponder key ECU Code 12 is not output when the door is open Door courtesy switch Wire harness or connector Transponder key ECU Code 13 is not output when ignition switch ON IGN Fuse Wire harness or connector Transponder key ECU Code 31 is not output when key is inserted in key cylinder Key code is not registered Code 32 is output Code 33 is output Transponder key amplifier Transponder key ECU Code 34 is output Transponder key ECU has no memory space to register key code Code 51 − 58 is output FCVC Transponder key ECU Transponder key coil Transponder key ECU Wire harness or connector Transponder key ECU BE−180 BODY ELECTRICAL S − ENGINE IMMOBILISER SYSTEM (Except 2UZ−FE) If code 32 is output, troubleshoot according to this flow chart Check for continuity between terminals of the transponder key coil NG Exchange the transponder key coil OK Exchange the transponder key amplifier OK Exchange the transponder key amplifier with a new one Check again whether the engine starts NG Reinstall the original transponder key amplifier Check the wire harness and connector NG Repair or replace the wire harness or the connector OK Check the wire harness and connector S If code 33 is output, troubleshoot according to this flow chart Exchange the transponder key amplifier with a new one Check again whether the engine starts NG Reinstall the original transponder key amplifier Exchange the transponder key amplifier OK Exchange the transponder key amplifier BE−98 BODY ELECTRICAL − ENGINE IMMOBILISER SYSTEM ENGINE IMMOBILISER SYSTEM BE1Z6−02 REGISTRATION PROCEDURE HINT: In case of having lost all the already registered master keys, you are not able to additional registration or deletion Change the Transponder key ECU and then must register the new key codes according to the following registration procedure of the automatic registration mode KEY REGISTRATION IN AUTOMATIC REGISTRATION MODE (a) Registration of a new transponder key HINT: S This must be done when you install a new Transponder key ECU S The new Transponder key ECU is on the automatic key code registration mode The already fixed number of key codes for this Transponder key ECU can be registered On this type of vehicle, up to key codes can be registered S A master and sub key are registered automatically START Security indicator blinks until the first key is inserted The indicator lights up after the key registration Insert the key in the key cylinder Under registration Security Indicator OFF Registration completion Remove the key Yes Will you register the next key? Security Indicator ON (After the last key (sub−key) has been registered, the indicator remain OFF until remove the key And after remove the key, the indicator blinks.) No END HINT: S S When a key is not inserted in the key cylinder on the automatic registration mode, the security indicator always lights on When the immobiliser system operates normally and the key is pull out, the security indicator blinks LAND CRUISER (W/G) SUP (RM970E) BE−99 BODY ELECTRICAL − ENGINE IMMOBILISER SYSTEM (b) Automatic registration mode completion If completing the mode forcibly when more than key code have been registered on the automatic registration mode, perform the following procedures After more key code have been registered with master key, perform step (1) or (2) without pulling the key out or inserting the already registered key (1) Turn the ignition switch LOCK ® ON times within 10 sec (2) With the TOYOTA hand−held tester, require automatic registration mode completion REGISTRATION OF ADDITIONAL MASTER KEY AND SUB KEY It is possible to carry out additional registration of the supply key HINT: S It is possible to register up to master key codes including the already registered key code S It is posible to register up to sub key codes including the aleady registed key code S When any operation time described below is over, registration mode completes S When the next procedure is performed while the timer is working, the timer completes counting time, then next timer starts S When replacing ”Ignition Cylinder Key Set” or ”Lock Cylinder Set” and register according to the following procedure using the original master key However, after the registration of the additional master key, as the original master key and the original sub−key is not necessary any more, so erase registration of those key codes S For the registration order, it is not necessary to distinguish between Main and Sub (Main key and Sub key are automatically identified) When a registration error in the transponder key ECU is detected, the security indicator indicates the following codes 2−1 Communication error between the key to be registered and the transponder key ECU 2−2 When trying to register the key that is already registered 2−3 When exceeding the number of keys can be retistered (Master key: 5, Sub key: 3) Blinks 1.8 Sec 0.2 Sec Code 2−1 0.25 Sec Sec Code2−3 0.25 Sec.0.5 Sec LAND CRUISER (W/G) SUP (RM970E) 0.25 Sec 0.25 Sec.0.5 Sec 0.25 Sec 0.5 Sec 0.25 Sec Code2−2 Sec Sec BE−100 BODY ELECTRICAL (1) − ENGINE IMMOBILISER SYSTEM Using hand−held tester: START Insert already registered master key in the key cylinder and turn the ignition switch ON Security indicator blinks Within 120 secs Security indicator OFF Within 20 secs Security indicator ON Within 10 secs Security indicator blinks Using TOYOTA hand−held tester, select key registration Remove the master key Insert key to be registered in key cylinder Keep ignition switch at ON position for 60 seconds or more Security indicator blinks Remove the key Security indicator OFF END HINT: Please follow the screen of the hand−held tester for more detailed procedure LAND CRUISER (W/G) SUP (RM970E) Security indicator blinks BE−101 BODY ELECTRICAL − ENGINE IMMOBILISER SYSTEM ERASURE OF TRANSPONDER KEY CODE Using hand−held tester: START Security indicator blinks Insert already registered master key in the key cylinder and turn the ignition switch ON Security indicator ON Using hand−held tester, select key erasion Remove the master key Within 10 secs Security indicator ON about sec and OFF Security indicator blinks END (Key code erased) HINT: S Follow the screen of the hand−held tester for more detailed procedure LAND CRUISER (W/G) SUP (RM970E) BE−181 BODY ELECTRICAL − ENGINE IMMOBILISER SYSTEM (Except 2UZ−FE) BE0YA−01 INSPECTION 1 INSPECT TRANSPONDER KEY COIL CONTINUITY Check that continuity exists between terminal and If continuity is not as specified, replace the coil I04266 INSPECT TRANSPONDER KEY ECU CIRCUIT Disconnect the connector from the ECU and inspect the connector on the wire harness side, as shown in the table below Wire Harness Side I07570 Tester connection Condition Specified condition − Ground Constant Battery voltage − Ground Ignition switch ON Battery voltage − Ground All doors closed No continuity − Ground All doors open Continuity − Ground Key unlock warning switch OFF (key removed) No continuity − Ground Key unlock warning switch ON (key inserted) Continuity 14 − Ground Constant Continuity If the circuit is not as specified, try replacing the ECU with a new one If the circuit is not as specified, inspect the circuits connected to other parts (a) (b) 10 (c) I07571 INSPECT TRANSPONDER KEY ECU With the connector connected, connect the positive (+) lead from the analog type tester to terminal 10 and the negative (−) lead to the body ground Check that there is battery voltage when the ignition switch turned ON Check that the tester needle swings strongly for approx sec when the engine is started using the ignition key BE−102 BODY ELECTRICAL − ENGINE IMMOBILISER SYSTEM BE02Q−25 LOCATION Engine Room R/B D EFI Fuse D EFI and ECD Relay Passenger Side Junction Block D IGN Fuse Transponder Key Coil Transponder Key Amplifier DLC3 ECM I06215 I25526 LAND CRUISER (W/G) SUP (RM970E) ... ignition key cylinder Close all the doors Within 40 sec Mode Selection Add mode Turn the IG SW ON ←→LOCK once Rewrite mode Turn the IG SW ON ←→LOCK twice HINT: If the IG switch operation is not performed... operation is finished with no response Confirmation mode Turn the IG SW ON ←→LOCK times Remove the key from the IG key cylinder Prohibition mode Turn the IG SW ON ←→LOCK times BE–122 BODY ELECTRICAL... PREPARATION − AUTOMATIC TRANSMISSION / TRANSAXLE Lubricant Automatic transmission fluid (LAND CRUISER/ LX470) Dry fill (2UZ−FE w oil cooler) Drain and refill (2UZ−FE w oil cooler) 11.6 liters (12.3 US