THÔNG TIN TÀI LIỆU
`,`,```,````,`,`,,,,``,`,,,`,,-`-`,,`,,`,`,,` - ASME B PVC.I X-2017 SECTION IX We l d i n g , Br a zi n g , a n d Fu sin g Qu alific ations 2017 ASME Boiler and Pressure Vessel Code An International Code Qual i fi cat i on St and ard for We l d i ng , Brazi ng , an d Fu sin g P roc e d ure s; We l d e rs; Bra zers; and We l d i ng , B razi ng, a n d Fusi ng Op e rat ors Copyright ASME International (BPVC) Provided by IHS under license with ASME No reproduction or networking permitted without license from IHS Licensee=Applus/5970480002, User=Miskell, Douglas Not for Resale, 07/11/2017 17:05:36 MDT Markings such as “ASME,” “ASME Standard,” or any other marking including “ASME,” ASME logos, or the Certification Mark shall not be used on any item that is not constructed in accordance with all of the applicable requirements of the Code or Standard. Use of ASME’s name, logos, or Certification Mark requires formal ASME certification; if no certification program is available, such ASME markings may not be used. (For Certification and Accreditation Programs, see https://www.asme.org/shop/certification‐accreditation.) Items produced by parties not formally certified by ASME may not be described, either explicitly or implicitly, as ASME certified or approved in any code forms or other document. `,`,```,````,`,`,,,,``,`,,,`,,-`-`,,`,,`,`,,` - Copyright ASME International (BPVC) Provided by IHS under license with ASME No reproduction or networking permitted without license from IHS Licensee=Applus/5970480002, User=Miskell, Douglas Not for Resale, 07/11/2017 17:05:36 MDT AN INTERNATIONAL CODE 2017 ASME Boiler & Pressure Vessel Code 2017 Edition July 1, 2017 `,`,```,````,`,`,,,,``,`,,,`,,-`-`,,`,,`,`,,` - IX QUALIFICATION STANDARD FOR WELDING, BRAZING, AND FUSING PROCEDURES; WELDERS; BRAZERS; AND WELDING, BRAZING, AND FUSING OPERATORS ASME Boiler and Pressure Vessel Committee on Welding, Brazing, and Fusing Two Park Avenue • New York, NY • 10016 USA Copyright ASME International (BPVC) Provided by IHS under license with ASME No reproduction or networking permitted without license from IHS Licensee=Applus/5970480002, User=Miskell, Douglas Not for Resale, 07/11/2017 17:05:36 MDT Date of Issuance: July 1, 2017 This international code or standard was developed under procedures accredited as meeting the criteria for American National Standards and it is an American National Standard The Standards Committee that approved the code or standard was balanced to assure that individuals from competent and concerned interests have had an opportunity to participate The proposed code or standard was made available for public review and comment that provides an opportunity for additional public input from industry, academia, regulatory agencies, and the public-at-large ASME does not “approve,” “rate,” or “endorse” any item, construction, proprietary device, or activity ASME does not take any position with respect to the validity of any patent rights asserted in connection with any items mentioned in this document, and does not undertake to insure anyone utilizing a standard against liability for infringement of any applicable letters patent, nor assume any such liability Users of a code or standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, is entirely their own responsibility Participation by federal agency representative(s) or person(s) affiliated with industry is not to be interpreted as government or industry endorsement of this code or standard ASME accepts responsibility for only those interpretations of this document issued in accordance with the established ASME procedures and policies, which precludes the issuance of interpretations by individuals The endnotes and preamble in this document (if any) are part of this American National Standard ASME collective membership mark Certification Mark The above ASME symbol is registered in the U.S Patent Office “ASME” is the trademark of The American Society of Mechanical Engineers No part of this document may be reproduced in any form, in an electronic retrieval system or otherwise, without the prior written permission of the publisher Library of Congress Catalog Card Number: 56-3934 Printed in the United States of America Adopted by the Council of The American Society of Mechanical Engineers, 1914; latest edition 2017 The American Society of Mechanical Engineers Two Park Avenue, New York, NY 10016-5990 Copyright © 2017 by THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS All rights reserved `,`,```,````,`,`,,,,``,`,,,`,,-`-`,,`,,`,`,,` - Copyright ASME International (BPVC) Provided by IHS under license with ASME No reproduction or networking permitted without license from IHS Licensee=Applus/5970480002, User=Miskell, Douglas Not for Resale, 07/11/2017 17:05:36 MDT TABLE OF CONTENTS List of Sections Foreword Statement of Policy on the Use of the Certification Mark and Code Authorization in Advertising Statement of Policy on the Use of ASME Marking to Identify Manufactured Items Submittal of Technical Inquiries to the Boiler and Pressure Vessel Standards Committees Personnel Introduction Summary of Changes List of Changes in Record Number Order Cross-Referencing and Stylistic Changes in the Boiler and Pressure Vessel Code x xii xiv xiv xv xviii xxxvii xl xlvii l Part QG QG-100 QG-109 General Requirements Scope Definitions 1 Part QW Welding 15 Article I QW-100 QW-110 QW-120 QW-130 QW-140 QW-150 QW-160 QW-170 QW-180 QW-190 Welding General Requirements Scope Weld Orientation Test Positions for Groove Welds Test Positions for Fillet Welds Types and Purposes of Tests and Examinations Tension Tests Guided‐Bend Tests Toughness Tests Fillet‐Weld Tests Other Tests and Examinations 15 15 15 15 16 16 17 18 19 19 21 Article II QW-200 QW-210 QW-220 QW-250 QW-290 Welding Procedure Qualifications General Preparation of Test Coupon Hybrid Welding Procedure Variables Welding Variables Temper Bead Welding 28 28 31 32 33 66 Article III QW-300 QW-310 QW-320 QW-350 QW-360 QW-380 Welding Performance Qualifications General Qualification Test Coupons Retests and Renewal of Qualification Welding Variables for Welders Welding Variables for Welding Operators Special Processes 70 70 72 73 74 75 76 Article IV QW-400 QW-410 QW-420 QW-430 QW-440 QW-450 QW-460 Welding Data Variables Technique Base Metal Groupings F‐Numbers Weld Metal Chemical Composition Specimens Graphics 78 78 88 92 163 174 175 180 iii Copyright ASME International (BPVC) Provided by IHS under license with ASME No reproduction or networking permitted without license from IHS `,`,```,````,`,`,,,,``,`,,,`,,-`-`,,`,,`,`,,` - Licensee=Applus/5970480002, User=Miskell, Douglas Not for Resale, 07/11/2017 17:05:36 MDT QW-470 Etching — Processes and Reagents 224 Article V QW-500 QW-510 QW-520 QW-530 QW-540 Standard Welding Procedure Specifications (SWPSs) General Adoption of SWPSs Use of SWPSs Without Discrete Demonstration Forms Production Use of SWPSs 226 226 226 226 227 227 Brazing 228 Article XI QB-100 QB-110 QB-120 QB-140 QB-150 QB-160 QB-170 QB-180 Brazing General Requirements Scope Braze Orientation Test Positions for Lap, Butt, Scarf, or Rabbet Joints Types and Purposes of Tests and Examinations Tension Tests Guided‐Bend Tests Peel Tests Sectioning Tests and Workmanship Coupons 228 228 228 228 229 229 230 231 231 Article XII QB-200 QB-210 QB-250 Brazing Procedure Qualifications General Preparation of Test Coupon Brazing Variables 232 232 234 234 Article XIII QB-300 QB-310 QB-320 QB-350 Brazing Performance Qualifications General Qualification Test Coupons Retests and Renewal of Qualification Brazing Variables for Brazers and Brazing Operators 238 238 239 239 239 Article XIV QB-400 QB-410 QB-420 QB-430 QB-450 QB-460 Brazing Data Variables Technique P‐Numbers F‐Numbers Specimens Graphics 240 240 241 241 241 244 248 Plastic Fusing 267 Article XXI QF-100 QF-110 QF-120 QF-130 QF-140 Plastic Fusing General Requirements Scope Fused Joint Orientation Test Positions Data Acquisition and Evaluation Examinations and Tests 267 267 267 267 267 268 Article XXII QF-200 QF-220 QF-250 Fusing Procedure Qualifications General Standard Fusing Procedure Specifications Fusing Variables 273 273 276 278 Article XXIII QF-300 QF-310 QF-320 QF-360 Plastic Fusing Performance Qualifications General Qualification Test Coupons Retests and Renewal of Qualification Essential Variables for Performance Qualification of Fusing Operators 280 280 281 281 281 Article XXIV QF-400 Plastic Fusing Data Variables 283 283 Part QB Part QF `,`,```,````,`,`,,,,``,`,,,`,,-`-`,,`,,`,`,,` - iv Copyright ASME International (BPVC) Provided by IHS under license with ASME No reproduction or networking permitted without license from IHS Licensee=Applus/5970480002, User=Miskell, Douglas Not for Resale, 07/11/2017 17:05:36 MDT QF-420 QF-450 QF-460 QF-480 QF-490 Material Groupings Pipe Fusing Limits Graphics Forms Definitions 284 285 285 297 307 Nonmandatory Appendix B B-100 Welding and Brazing Forms Forms 308 308 Nonmandatory Appendix D P‐Number Listing 319 Mandatory Appendix E Permitted SWPSs 338 Mandatory Appendix F Standard Units for Use in Equations 341 Nonmandatory Appendix G G-100 G-200 G-300 Guidance for the Use of U.S Customary and SI Units in the ASME Boiler and Pressure Vessel Code Use of Units in Equations Guidelines Used to Develop SI Equivalents Soft Conversion Factors 342 342 342 344 Nonmandatory Appendix H H-100 H-200 H-300 H-400 H-500 Waveform Controlled Welding Background Waveform Controlled Welding and Heat Input Determination New Procedures Qualifications Existing Qualified Procedures Performance Qualifications 345 345 345 345 346 346 Mandatory Appendix J Guideline for Requesting P-Number Assignments for Base Metals not Listed in Table QW/QB-422 Introduction Request Format Submittals 347 347 347 347 Guidance on Invoking Section IX Requirements in Other Codes, Standards, Specifications, and Contract Documents Background and Purpose Scope of Section IX and What Referencing Documents Must Address Recommended Wording — General 348 348 348 348 Welders and Welding Operators Qualified Under ISO 9606-1:2012 and ISO 14732-2013 Introduction Administrative Requirements Technical Requirements Testing Requirements 350 350 350 350 350 J-100 J-200 J-300 Nonmandatory Appendix K K-100 K-200 K-300 Nonmandatory Appendix L L-100 L-200 L-300 L-400 FIGURES QG-109.2.1 QG-109.2.2 QW-191.1.2.2(b)(4) QW-461.1 QW-461.2 QW-461.3 QW-461.4 QW-461.5 QW-461.6 QW-461.7 QW-461.8 QW-461.10 QW-462.1(a) Typical Single and Multibead Layers Typical Single Bead Layers Rounded Indication Charts Positions of Welds — Groove Welds Positions of Welds — Fillet Welds Groove Welds in Plate — Test Positions Groove Welds in Pipe — Test Positions Fillet Welds in Plate — Test Positions Fillet Welds in Pipe — Test Positions Stud Welds — Test Positions Stud Welds — Welding Positions Rotating Tool Design Characteristics (FSW) Referenced in QW-410 Tension — Reduced Section — Plate v `,`,```,````,`,`,,,,``,`,,,`,,-`-`,,`,,`,`,,` - Copyright ASME International (BPVC) Provided by IHS under license with ASME No reproduction or networking permitted without license from IHS Licensee=Applus/5970480002, User=Miskell, Douglas Not for Resale, 07/11/2017 17:05:36 MDT 13 14 22 180 181 182 182 183 184 185 185 187 188 QW-462.1(b) QW-462.1(c) QW-462.1(d) QW-462.1(e) QW-462.2 QW-462.3(a) QW-462.3(b) QW-462.4(a) QW-462.4(b) QW-462.4(c) QW-462.4(d) QW-462.5(a) QW-462.5(b) QW-462.5(c) QW-462.5(d) QW-462.5(e) QW-462.7.1 QW-462.7.2 QW-462.7.3 QW-462.8.1 QW-462.8.2 QW-462.9 QW-462.12 QW-462.13 QW-463.1(a) QW-463.1(b) QW-463.1(c) QW-463.1(d) QW-463.1(e) QW-463.1(f) QW-463.2(a) QW-463.2(b) `,`,```,````,`,`,,,,``,`,,,`,,-`-`,,`,,`,`,,` - QW 463.2(c) QW-463.2(d) QW-463.2(e) QW-463.2(f) QW-463.2(g) QW-463.2(h) QW-464.1 QW-464.2 QW-466.1 QW-466.2 QW-466.3 QW-466.4 QW-466.5 QW-466.6 QW-469.1 QW-469.2 QB-461.1 QB-461.2 QB-462.1(a) Tension — Reduced Section — Pipe Tension — Reduced Section Alternate for Pipe Tension — Reduced Section — Turned Specimens Tension — Full Section — Small Diameter Pipe Side Bend Face and Root Bends — Transverse Face and Root Bends — Longitudinal Fillet Welds in Plate — Procedure Fillet Welds in Plate — Performance Fillet Welds in Pipe — Performance Fillet Welds in Pipe — Procedure Chemical Analysis and Hardness Specimen Corrosion‐Resistant and Hard‐Facing Weld Metal Overlay Chemical Analysis Specimen, Hard‐Facing Overlay Hardness, and Macro Test Location(s) for Corrosion‐Resistant and Hard‐Facing Weld Metal Overlay Pipe Bend Specimen — Corrosion‐Resistant Weld Metal Overlay Plate Bend Specimens — Corrosion‐Resistant Weld Metal Overlay Plate Macro, Hardness, and Chemical Analysis Specimens — Corrosion‐Resistant and Hard‐Facing Weld Metal Overlay Resistance Seam Weld Test Coupon Seam Weld Section Specimen Removal Resistance Weld Nugget Section Test Specimens Spot Welds in Sheets Seam Weld Peel Test Specimen and Method Spot Welds in Sheet Nomenclature for Temper Bead Welding Measurement of Temper Bead Overlap Plates — Less Than 3/4 in (19 mm) Thickness Procedure Qualification Plates — 3/4 in (19 mm) and Over Thickness and Alternate From 3/8 in (10 mm) but Less Than 3/4 in (19 mm) Thickness Procedure Qualification Plates — Longitudinal Procedure Qualification Procedure Qualification Procedure Qualification Toughness Test Specimen Location Plates — Less Than 3/4 in (19 mm) Thickness Performance Qualification Plates — 3/4 in (19 mm) and Over Thickness and Alternate From 3/8 in (10 mm) but Less Than 3/4 in (19 mm) Thickness Performance Qualification Plates — Longitudinal Performance Qualification Performance Qualification Performance Qualification Pipe — NPS 10 (DN 250) Assembly Performance Qualification NPS (DN 150) or NPS (DN 200) Assembly Performance Qualification Performance Qualification Procedure Qualification Test Coupon and Test Specimens Performance Qualification Test Coupons and Test Specimens Test Jig Dimensions Guided‐Bend Roller Jig Guided‐Bend Wrap Around Jig Stud‐Weld Bend Jig Torque Testing Arrangement for Stud Welds Suggested Type Tensile Test Figure for Stud Welds Butt Joint Alternative Butt Joint Flow Positions Test Flow Positions Tension — Reduced Section for Butt and Scarf Joints — Plate Copyright ASME International (BPVC) Provided by IHS under license with ASME No reproduction or networking permitted without license from IHS vi Licensee=Applus/5970480002, User=Miskell, Douglas Not for Resale, 07/11/2017 17:05:36 MDT 188 189 189 190 191 192 193 193 194 194 195 195 196 197 198 199 199 200 200 201 202 203 207 208 208 208 209 209 210 210 211 211 212 212 213 213 214 215 216 217 218 220 220 221 222 223 224 224 248 249 250 `,`,```,````,`,`,,,,``,`,,,`,,-`-`,,`,,`,`,,` - Tension — Reduced Section for Butt, Lap, and Scarf Joints — Pipe Tension — Reduced Section for Lap and Rabbet Joints — Plate Tension — Full Section for Lap, Scarf, and Butt Joints — Small Diameter Pipe Support Fixture for Reduced‐Section Tension Specimens Transverse First and Second Surface Bends — Plate and Pipe Longitudinal First and Second Surface Bends — Plate Lap Joint Peel Specimen Lap Joint Section Specimen (See QB-181) Workmanship Coupons Plates Procedure Qualification Plates Procedure Qualification Plates Procedure Qualification Plates Procedure Qualification Pipe — Procedure Qualification Plates Performance Qualification Plates Performance Qualification Pipe Performance Qualification Guided‐Bend Jig Guided‐Bend Roller Jig Guided‐Bend Wrap Around Jig Required Minimum Melt Bead Size Fusing Positions Fusing Test Positions Cross Section of Upset Beads for Butt-Fused PE Pipe Bend Test Specimen Removal, Configuration, and Testing HSTIT Specimen Configuration and Dimensions HSTIT Specimen Failure Examples Electrofusion Crush Test Electrofusion Bend Test Fusion Zone Void Criteria Electrofusion Peel Test Short-Term Hydrostatic Test Specimen QB-462.1(b) QB-462.1(c) QB-462.1(e) QB-462.1(f) QB-462.2(a) QB-462.2(b) QB-462.3 QB-462.4 QB-462.5 QB-463.1(a) QB-463.1(b) QB-463.1(c) QB-463.1(d) QB-463.1(e) QB-463.2(a) QB-463.2(b) QB-463.2(c) QB-466.1 QB-466.2 QB-466.3 QF-221.1 QF-461.1 QF-461.2 QF-462 QF-463 QF-464 QF-465 QF-466 QF-467 QF-468 QF-469 QF-470 TABLES QW-252 QW-252.1 QW-253 QW-253.1 QW-254 QW-254.1 QW-255 QW-255.1 QW-256 QW-256.1 QW-257 QW-257.1 QW-258 QW-258.1 QW-259 QW-260 QW-261 QW-262 QW-263 Welding Variables Procedure Specifications (WPS) — Oxyfuel Gas Welding (OFW) Welding Variables Procedure Specifications (WPS) — Oxyfuel Gas Welding (OFW) Welding Variables Procedure Specifications (WPS) — Shielded Metal‐Arc Welding (SMAW) Welding Variables Procedure Specifications (WPS) — Shielded Metal‐Arc Welding (SMAW) Welding Variables Procedure Specifications (WPS) — Submerged‐Arc Welding (SAW) Welding Variables Procedure Specifications (WPS) — Submerged‐Arc Welding (SAW) Welding Variables Procedure Specifications (WPS) — Gas Metal‐Arc Welding (GMAW and FCAW) Welding Variables Procedure Specifications (WPS) — Gas Metal‐Arc Welding (GMAW and FCAW) Welding Variables Procedure Specifications (WPS) — Gas Tungsten‐Arc Welding (GTAW) Welding Variables Procedure Specifications (WPS) — Gas Tungsten‐Arc Welding (GTAW) Welding Variables Procedure Specifications (WPS) — Plasma‐Arc Welding (PAW) Welding Variables Procedure Specifications (WPS) — Plasma‐Arc Welding (PAW) Welding Variables Procedure Specifications (WPS) — Electroslag Welding (ESW) Welding Variables Procedure Specifications (WPS) — Electroslag Welding (ESW) Welding Variables Procedure Specifications (WPS) — Electrogas Welding (EGW) Welding Variables Procedure Specifications (WPS) — Electron Beam Welding (EBW) Welding Variables Procedure Specifications (WPS) — Stud Welding Welding Variables Procedure Specifications (WPS) — Inertia and Continuous Drive Friction Welding Welding Variables Procedure Specifications (WPS) — Resistance Welding vii Copyright ASME International (BPVC) Provided by IHS under license with ASME No reproduction or networking permitted without license from IHS Licensee=Applus/5970480002, User=Miskell, Douglas Not for Resale, 07/11/2017 17:05:36 MDT 251 252 253 254 255 255 256 256 257 258 258 259 260 261 262 263 264 265 266 266 277 285 286 287 288 290 291 292 293 294 295 296 34 35 36 37 38 39 40 42 43 45 46 48 50 51 52 53 54 55 56 QW-264 QW-264.1 QW-264.2 QW-265 QW-266 QW-267 QW-290.4 QW-352 QW-353 QW-354 QW-355 QW-356 QW-357 QW-416 QW/QB-422 QW-432 QW-442 QW-451.1 QW-451.2 QW-451.3 QW-451.4 QW-452.1(a) QW-452.1(b) QW-452.3 QW-452.4 QW-452.5 QW-452.6 QW-453 QW-461.9 QW-462.10(a) QW-462.10(b) QW-462.10(c) QW-473.3-1 QB-252 QB-253 QB-254 QB-255 QB-256 QB-257 QB-432 QB-451.1 QB-451.2 QB-451.3 QB-451.4 QB-451.5 QB-452.1 QB-452.2 QF-144.2 QF-144.2.3 QF-202.2.2 QF-221.2 QF-222.1 QF-254 QF-255 Welding Variables Procedure Specifications (WPS) — Laser Beam Welding (LBW) Welding Variables Procedure Specifications (WPS) — Laser Beam Welding (LBW) Welding Variables Procedure Specifications (WPS) — Low-Power Density Laser Beam Welding (LLBW) Welding Variables Procedure Specifications (WPS) — Flash Welding Welding Variables Procedure Specifications (WPS) — Diffusion Welding (DFW) Welding Variables Procedure Specifications — Friction Stir Welding (FSW) Welding Variables for Temper Bead Procedure Qualification Oxyfuel Gas Welding (OFW) Shielded Metal‐Arc Welding (SMAW) Semiautomatic Submerged‐Arc Welding (SAW) Semiautomatic Gas Metal‐Arc Welding (GMAW) Manual and Semiautomatic Gas Tungsten‐Arc Welding (GTAW) Manual and Semiautomatic Plasma‐Arc Welding (PAW) Welding Variables Ferrous and Nonferrous P‐Numbers F‐Numbers A‐Numbers Groove‐Weld Tension Tests and Transverse‐Bend Tests Groove‐Weld Tension Tests and Longitudinal‐Bend Tests Fillet‐Weld Tests Fillet Welds Qualified by Groove‐Weld Tests Test Specimens Thickness of Weld Metal Qualified Groove‐Weld Diameter Limits Small Diameter Fillet‐Weld Test Fillet‐Weld Test Fillet Qualification by Groove‐Weld Tests Procedure and Performance Qualification Thickness Limits and Test Specimens for Hard‐ Facing (Wear‐Resistant) and Corrosion‐Resistant Overlays Performance Qualification — Position and Diameter Limitations Shear Strength Requirements for Spot or Projection Weld Specimens Shear Strength Requirements for Spot or Projection Weld Specimens Shear Strength Requirements for Spot or Projection Weld Specimens Makeup of Equations for Aqua Regia and Lepito’s Etch Torch Brazing (TB) Furnace Brazing (FB) Induction Brazing (IB) Resistance Brazing (RB) Dip Brazing — Salt or Flux Bath (DB) Dip Brazing — Molten Metal Bath (DB) F‐Numbers Tension Tests and Transverse‐Bend Tests — Butt and Scarf Joints Tension Tests and Longitudinal Bend Tests — Butt and Scarf Joints Tension Tests and Peel Tests — LAP Joints Tension Tests and Section Tests — Rabbet Joints Section Tests — Workmanship Coupon Joints Peel or Section Tests — Butt, Scarf, Lap, Rabbet Joints Section Tests — Workmanship Specimen Joints Testing Speed Requirements Electrofusion Procedure Qualification Test Coupons Required Maximum Heater Plate Removal Time for Pipe-to-Pipe Fusing Electrofusion Material Combinations Fusing Variables Procedure Specification Fusing Variables Procedure Specification `,`,```,````,`,`,,,,``,`,,,`,,-`-`,,`,,`,`,,` - Copyright ASME International (BPVC) Provided by IHS under license with ASME No reproduction or networking permitted without license from IHS viii Licensee=Applus/5970480002, User=Miskell, Douglas Not for Resale, 07/11/2017 17:05:36 MDT 57 58 59 61 62 63 67 74 74 74 74 75 75 91 93 164 174 175 176 176 176 177 177 178 178 178 179 179 186 204 205 206 225 234 235 235 236 236 237 242 244 244 245 245 246 247 247 271 272 275 277 278 279 279 ... QW-264 QW-264.1 QW-264.2 QW-265 QW-266 QW-267 QW-290.4 QW-352 QW-353 QW-354 QW-355 QW-356 QW-357 QW-416 QW/QB-422 QW-432 QW-442 QW-451.1 QW-451.2 QW-451.3 QW-451.4 QW-452.1(a) QW-452.1(b) QW-452.3... QW-452.4 QW-452.5 QW-452.6 QW-453 QW-461.9 QW-462.10(a) QW-462.10(b) QW-462.10(c) QW-473. 3-1 QB-252 QB-253 QB-254 QB-255 QB-256 QB-257 QB-432 QB-451.1 QB-451.2 QB-451.3 QB-451.4 QB-451.5 QB-452.1... 350 J-100 J-200 J-300 Nonmandatory Appendix K K-100 K-200 K-300 Nonmandatory Appendix L L-100 L-200 L-300 L-400 FIGURES QG-109.2.1 QG-109.2.2 QW-191.1.2.2(b)(4) QW-461.1 QW-461.2 QW-461.3 QW-461.4
Ngày đăng: 13/01/2020, 11:37
Xem thêm: