1 chemical (v3)web

1 Chemical Fixings Chemical fixings Good reasons to choose fischer ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ Chemical fixings Resin Performance - Introduction Highbond-System FHB II Highbond anchor FHB II-A S / FHB II-A L Powerbond injection resin FIS PM with FIS PS sleeve Superbond resin system FIS SB with RSB capsules Injection resin FIS EM Injection resin FIS EM + threaded rods for cracked concrete FIS EM + RG MI internally threaded rods for cracked concrete Resin dispenser guns R resin anchor with RG M threaded rod R resin anchor + RG M I for cracked concrete FIS V injection resin system FIS VT injection resin system Resin studs for non-cracked concrete Internally threaded stud RG M I for non-cracked concrete Injection resin FIS P / FIP Injection resin in solid brick masonry Injection resin in perforated brick FIS A withinjection resin for aerated concrete Rebar connections Highbond anchor dynamic FHB dyn Fill & Fix injection fixing 3-5 14 19 30 33 38 39 40 46 49 53 55 62 65 67 71 75 78 82 86 Performance of injection resins Performance positioning of fischer injection resins Chemical Fixings High performance resins IMPROVED *BETTER* **BEST** Specialist resin designed for use in cracked concrete High performance resin for cracked concrete Highbond FHB II Powerbond FIS PB Superbond FIS SB Epoxy resin FIS EM Universal resins High performance resins with approvals for virtually all substrates and many applications FIS V / FIS VW Hybrid vinyl ester resin Vinyl ester resin FIS VT Basic resins + approval Resin with an ETA for use in masonry FIS P Plus Hybrid polyester resin GOOD Basic resins Cost effective resin with NO approval for use in masonry Polyester resin FIS P F-Bond, FIP C 700 PERFORMANCE / PRICE Resin for cracked concrete ▪ High performance, reduced sensitivity to badly cleaned holes ▪ High temperature resistance (except epoxy) ▪ First-rate, long term behaviour in concrete or wet substrates PRICE Vinyl ester ▪ Good performance, medium sensitivity to badly cleaned holes ▪ Good tempertaure and chemical resistance ▪ Good, long term behaviour in concrete or wet substrates Polyester hybrid ▪ Medium performance, medium sensitivity to badly cleaned holes ▪ Good temperature and chemical resistance ▪ Meduim, long term behaviour in concrete or wet substrates PERFORMANCE Polyester ▪ Low performance, high sensitivity to badly cleaned holes ▪ Medium temperature and chemical resistance ▪ Bad long term behaviour in concrete or wet substrates ▪ Some manufacturers may still offer their resin with a styrene health risk Chemical fixings Performance of injection resins Performance positioning of fischer injection resins LOADS 40 20 120% ~ 90% ~100% ~75-80% Polyester Resins Pure vinyl ester resins Hybrid vinyl ester resins Resins for cracked concrete SENSITIVITY TO THE HOLE CLEANING Relative bond strength, arbitrary unit Load levels in concrete % 120 100 80 60 Influence of hole cleaning method % 120 100 80 60 40 20 Hybrid vinyl ester system Polyester system -25% -50% Cleaned: x blow out, x brush, x blow out Uncleaned: x blow out, x brush, x blow out Uncleaned: x blow out Hybrid VE resins - reduced sensitivity in imperfectly cleaned holes: ▪ Higher safety for fixings ▪ Methods recommended as part of best practice in hole cleaning in accordance with ETA procedures DRILL HOLE CLEANING ACCESSORIES For best results always use cleaning accessories with every resin application Remember to use the correct cleaning accessories as per the latest ETA approval Cleaning brush BS for concrete Cleaning brush with thread M Cleaning brush FIS for MASONRY Hole cleaning pump ABG Compressed air gun ABP Resin site box FIS EM Performance of injection resins fischer Highbond system FHB II The premium solution for cracked concrete ▪ Maximum loads for the most demanding applications ▪ Extensively tested and safety proven ▪ The systems uses ‘cone’ anchor technology ▪ Minimum edge axial spacing ▪ High temperature and chemical resistance ▪ Unique fast cure capsule Chemical Fixings fischer composite anchor systems for cracked concrete fischer Powerbond system FIS PM The cost effective option for cracked concrete ▪ High load capacity ▪ Variable anchorage depth for optimal dimensioning ▪ Unique PowerSleeve technology with conventional studs ▪ Approved for diamond drilled holes ▪ Approval for water filled holes ▪ Maximum flexibility and efficiency fischer Superbond system FIS SB / RSB The universal solution ▪ FIS SB Injection resin & RSB capsule systems with conventional anchor studs ▪ For applications down to -30OC with RSB ▪ Anchorage depth of 60mm-600mm, ideal for shallow and deep embedment depths ▪ For anchor rods M8-M30 and fischer internally threaded anchors M8-M20 ▪ RSB Capsule approved for diamond drilled and water filled holes FHB II Highbond resin system Chemical fixings The best performance in cracked concrete Banisters Steel girders BUILDING MATERIALS APPROVALS Approved for: ▪ Concrete C20/25 to C50/60, cracked and non-cracked Also suitable for: ▪ Concrete C12/15 ADVANTAGES APPLICATIONS FUNCTIONING ▪ The Highbond system FHB II achieves the highest load values in cracked concrete Thus fewer fixing points and smaller anchor plates are required ▪ The injection resin FIS  HB and the capsules FHB  II-P/PF offer the same performance and can be used with the FHB II-A S (short version) or L (long version) anchor rods Thus, you can select the most economical solution based on requirements ▪ The large cartridge size of the injection resin FIS  HB is ideally suited for continuous installation ▪ The pre-portioned resin capsule FHB II-P/PF represents an economical solution for individual applications ▪ The special formulation used in the capsule FHB  II-PF ensures particularly fast setting, providing quick installation ▪ Can be used in flooded drill holes ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ The FHB  II is a bonded anchor with torque-controlled expansion for pre-positioned and push-through installation ▪ The anchor rod can be set either with injection resin FIS  HB or with the capsule FHB II-P(F), and is fully bonded in the drill hole ▪ When tightening the hexagon nut, the anchor rod cones are pulled into the resin shell, which expands against the drill hole wall ▪ The styrene-free vinyl ester resin fully seals the drill hole ▪ When using the resin capsule, set the anchor rod through rotating and hammer motions with a hammer drill The RA-SDS setting tool, item no 62420 is recommended, see page INSTALLATION CAPSULE Note: For drill hole diameter 25mm, clean with compressed air INSTALLATION WITH INJECTION RESIN Guard rails Faỗades Staircases Steel consoles Machines Silo installations Masts Skirting protection Steelwork constructions Timber constructions FHB II Highbond resin system TECHNICAL DATA Approval Drill hole diameter h0 hef Art.-No ETA [mm] [mm] [mm] 096824 096847 508016 096843 096848 507922 096844 096849 507923 507924 096845 507925 096846 096851 507926 ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ 10 10 10 12 12 14 14 16 18 18 18 25 25 25 25 75 75 90 110 90 115 135 110 145 165 175 190 235 190 235 60 60 75 95 75 100 120 95 125 145 160 170 210 170 210 Items to order only Item FHB II-P x 60 FHB II-P 10 x 60 FHB II-P 10 x 75 FHB II-P 10 x 95 FHB II-P 12 x 75 FHB II-P 12 x 100 FHB II-P 12 x 120 FHB II-P 16 x 95 FHB II-P 16 x 125 FHB II-P 16 x 145 FHB II-P 16 x 160 FHB II-P 20 x 170 FHB II-P 20 x 210 FHB II-P 24 x 170 FHB II-P 24 x 210 Drill hole depth Anchorage depth Fits Sales unit [pcs] FHB II-A L M x 60 FHB II-S M 10 x 60 FHB II-A S M 10 x 75 FHB II-A L M 10 x 95 FHB II-A S M 12 x 75 FHB II-A L M 12 x 100 FHB II-A L M 12 x 120 FHB II-A S M 16 x 95 FHB II-A L M 16 x 125 FHB II-A L M 16 x 145 FHB II-A L M 16 x 160 FHB II-A S M 20 x 170 FHB II-A L M 20 x 210 FHB II-A S M 24 x 170 FHB II-A L M 24 x 210 10 10 10 10 10 10 10 10 10 10 10 4 4 Chemical Fixings Resin capsule FHB II-P (standard) TECHNICAL DATA Approval Resin capsule FHB II-PF (fast curing) Drill hole diameter h0 hef Art.-No ETA [mm] [mm] [mm] 500542 500547 507999 500543 500548 508000 500544 500549 508001 508002 500545 508003 500546 500550 508004 ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ 10 10 10 12 12 14 14 16 18 18 18 25 25 25 25 75 75 90 110 90 115 135 110 145 165 175 190 235 190 235 60 60 75 95 75 100 120 95 125 145 160 170 210 170 210 Items to order only Item FHB II-PF x 60 FHB II-PF 10 x 60 FHB II-PF 10 X 75 FHB II-PF 10 x 95 FHB II-PF 12 x 75 FHB II-PF 12 x 100 FHB II-PF 12 x 120 FHB II-PF 16 x 95 FHB II-PF 16 x 125 FHB II-PF 16 x 145 FHB II-PF 16 x 160 FHB II-PF 20 x 170 FHB II-PF 20 x 210 FHB II-PF 24 x 170 FHB II-PF 24 x 210 Drill hole depth Anchorage depth Fits Sales unit [pcs] FHB II-A L M x 60 FHB II-S M 10 x 60 FHB II-A S M 10 x 75 FHB II-A L M 10 x 95 FHB II-A S M 12 x 75 FHB II-A L M 12 x 100 FHB II-A L M 12 x 120 FHB II-A S M 16 x 95 FHB II-A L M 16 x 125 FHB II-A L M 16 x 145 FHB II-A L M 16 x 160 FHB II-A S M 20 x 170 FHB II-A L M 20 x 210 FHB II-A S M 24 x 170 FHB II-A L M 24 x 210 10 10 10 10 10 10 10 10 10 10 10 4 4 TECHNICAL DATA Approval Injection resin FIS HB 345 S + static mixer  FIS S Items to order only Item FIS HB 345 S FIS Mixer Red Languages on the cartridge Contents D, GB, F, E, NL, CZ — cartridge 360 ml, x static mixer FIS S 10 static mixer ETA 033211 096448 ■ — Sales unit [pcs] 10 FHB II Highbond resin system Chemical fixings CURING TIME - FIS HB Cartridge temperature FIS HB (minimum + 5°C) Gelling time FIS HB Temperature at anchoring base Curing time 15  6  4  2 ‒ 5°C – ± 0°C ± 0°C – + 5°C + 5°C – +20°C +20°C – +30°C +30°C – +40°C     > +40°C 360 180  90  35  20  12 FIS HB + 5°C – +20°C +20°C – +30°C +30°C – +40°C     > +40°C CURING TIME - FHB II P / FHB II- PF Temperature at anchoring base Curing time ‒ 5°C – ± 0°C ±  0°C – +10°C +10°C – + 20°C     ≧ + 20°C FHB II-P FHB II-PF 240  45  20  10 min min Please note: The curing times apply for dry anchoring bases, in damp anchoring bases they should be doubled Remove water from drill hole DISPENSERS Items to order only Item Dispenser FIS AP Dispenser FIS AM Dispenser FIS DM S Art.-No Dispenser FIS DC S Suitable for Sales unit [pcs] Performance data FIS V 360 S, FIS HB 345 S, Powerbond, Superbond FIS HB 150 C, FIS 511118 EM 390 S, FIS VS 150 C, FIS VW 360 S, FIS P 360 S, FIS P 300 T and — 1K-cartridges FIS V 360 S, FIS HB 345 S, FIS HB 150 C, FIS EM 390 S, FIS VS 150 C, FIS AM 056052 — FIS VW 360 S, FIS VT 300 T, FIS P 300 T and 1K-cartridges FIS V 360 S, FIS HB 345 S, Powerbond, Superbond FIS HB 150 C, FIS Recommeneded pressure bar FIS AP 058027 EM 390 S, FIS VS 150 C, FIS VW 360 S, FIS P 300 T, and 1K-cartridges Air compression Max 40 I/min FIS HB 345 S, FIS EM 390 S, FIS V 360 S, FIS P 300 T, FIS VS 150 C — FIS DC S 513423 and silicone cartridges Charger DCC 4000 507791 — Charger 12 V // 230 V Euro plug Battery pack DC 507792 — Battery pack 12 V // 2,0 Ah // Ni-MH For the full range of Dispenser Guns please refer to page 39 FIS DM S 1 1 1 DRILL HOLE CLEANING ACCESSORIES Metal cleaning brush BS for concrete Cleaning brush with thread M Items to order only Item BS ø 10 BS ø 12 BS ø 14 BS ø 16/18 BS ø 25 Brush for drill-Ø 40 mm Brush for drill-Ø 45 mm Brush for drill-Ø 55 mm FIS brush extension Compressed-air cleaning gun ABP ABG hole cleaning pump Acessories: Centring wedge RA-SDS Art.-No 078178 078179 078180 078181 097806 505061 506254 505062 508791 059456 089300 093076 062420 Compressed air gun Hole cleaning pump ABG Centring wedge Machine setting tool RA-SDS Brush diameter For drill diameter Sales unit [mm] [mm] [pcs] 11 13 16 20 27 42 47 58 — FHB II-A M20 - M24 — Use for overhead Installations Adapter suitable fits set screw 10 12 14 16/18 25 40 45 55 — — 1 1 1 1 1 10 FHB II-AS/AL Highbond resin system Bridge railings Chemical Fixings The best performance in cracked concrete with the least installation effort Balcony railings VERSIONS APPROVALS ▪ zinc-plated steel ▪ stainless steel ▪ high corrosion-resistant steel BUILDING MATERIALS FHB II-AS FHB II-AL ADVANTAGES - FHB II-AS FHB II-AS Highbond ▪ The reduced anchorage depth of the FHB  II-A  S minimises the drilling and installation effort; providing a very economical fixing ▪ The drill bit diameter is the same as the thread diameter This allows for pushthrough installation without additional tools and reduces the amount of resin required ▪ The cone shape of the anchor rod is most effective for small axial and edge distances in both cracked concrete and thin concrete As a result, it is suitable for a wide range of applications ▪ The anchor rod is approved for use both with capsules and with injection resin which guarantees a maximum flexibility of applications Approved for: ▪ Concrete C20/25 to C50/60, cracked and non-cracked Also suitable for: ▪ Concrete C12/15 ADVANTAGES - FHB II-AS FHB II-AL Highbond ▪ The large anchorage depth of the anchor rod FHB II-A L allows the system to achieve maximum load values with fewer fixing points and smaller anchor plates ▪ The double cone shape of the anchor rod has been designed to achieve high tensile loads, as a result it is able to achieve high performances in cracked concrete ▪ When using the FHB  II-A  L rod with injection resin FIS HB, push-through installation with annular gap filling is possible without the use of any further tools ▪ The FHB II-A L anchor rod is approved for use both with capsules and with injection resin This guarantees maximum flexibility in the application APPLICATIONS Guard rails Faỗades Staircases ▪ Steel consoles ▪ Masts ▪ Machines ▪ Silo installations ▪ Skirting protection ▪ Steelwork constructions ▪ Timber constructions Ideal for: ▪ Push-through installation FUNCTIONING ▪ ▪ ▪ ▪ ▪ ▪ ▪ The FHB II is a bonded anchor with torque-controlled expansion for pre-positioned and push-through installation With the FHB II-AS, the drill bit diameter is the same as the thread diameter, similar to a through bolt When using FHB II-A L in push-through installation, the annular gap has to be filled with the injection resin FIS HB The anchor rod can be set either with injection resin FIS HB or with the capsule FHB II-P(F), and is fully bonded in the drill hole When tightening the hexagon nut, the anchor rod cones are pulled into the resin shell, which expands against the drill hole wall The styrene-free vinyl ester resin fully seals the drill hole When using the resin capsule, set the anchor rod through rotating and hammering motions with a hammer drill The RA-SDS setting tool, item no 62420., Is recommended TIP - For use with Resin FIS HB - see page 6/ Resin Capsules FHB II-P - see page 7/ Resin Capsules FHB II-F - see page FHB II-AS/AL Highbond resin system Chemical fixings INSTALLATION CAPSULE For drill hole diameter 25mm, clean with compressed air INSTALLATION WITH INJECTION RESIN For drill hole diameter 25mm, clean with compressed air TECHNICAL DATA Items to order only zinc-plated steel stainless steel highly corrosion resistant steel Art.-No Art.-No A4 Art.-No C Item gvz Approval Highbond anchor  FHB II-A S (short version) ETA Drill hole diameter Drill hole depth [mm] h0 [mm] FHB II-A S M10 x 60/10 097072 097630 097704 1) ■ 10 75 10 75 FHB II-A S M10 x 60/20 097073 097631 097705 1) ■ with compressed 097632 25mm, — clean ■ 10 75air FHB II-A S M10 x 60/40 For drill — hole diameter — ■ 10 75 FHB II-A S M10 x 60/60 097074 097633 — ■ 10 75 FHB II-A S M10 x 60/100 097206 097634 — ■ 10 90 FHB II-A S M10 x 75/10 506884 506888 — ■ 10 90 FHB II-A S M10 x 75/20 506885 506889 506890 — ■ 10 90 FHB II-A S M10 x 75/40 — — ■ 10 90 FHB II-A S M10 x 75/60 506886 506891 — ■ 10 90 FHB II-A S M10 x 75/100 506887 506892 — ■ 12 90 FHB II-A S M12 x 75/10 097257 097635 12 90 FHB II-A S M12 x 75/25 097268 097636 097706 1) ■ 097637 097707 1) ■ 12 90 FHB II-A S M12 x 75/40 — — ■ 12 90 FHB II-A S M12 x 75/60 097274 097638 — ■ 12 90 FHB II-A S M12 x 75/100 097275 097639 — ■ 12 90 FHB II-A S M12 x 75/165 097280 097640 16 110 FHB II-A S M16 x 95/30 097281 097641 097708 1) ■ 16 110 FHB II-A S M16 x 95/60 097286 097642 097709 1) ■ — ■ 16 110 FHB II-A S M16 x 95/100 097295 097643 — ■ 16 110 FHB II-A S M16 x 95/165 097296 097644 — ■ 25 190 FHB II-A S M20 x 170/50 506917 506919 25 190 FHB II-A S M24 x 170/50 097297 097645 097711 1) ■ 1) Prices and delivery time on request Anchorage Fixture depth thickness hef tfix [mm] [mm] 60 60 60 60 60 75 75 75 75 75 75 75 75 75 75 75 95 95 95 95 170 170 10 20 40 60 100 10 20 40 60 100 10 25 40 60 100 165 30 60 100 165 50 50 Thread M M 10 M 10 M 10 M 10 M 10 M 10 M 10 M 10 M 10 M 10 M 12 M 12 M 12 M 12 M 12 M 12 M 16 M 16 M 16 M 16 M 20 M 24 Width Sales unit across nut  SW [mm] [pcs] 17 17 17 17 17 17 17 17 17 17 19 19 19 19 19 19 24 24 24 24 30 36 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 4 FILLING QUANTITIES Type FHB II-A S M10 x 60 FHB II-A S M10 x 75 FHB II-A S M12 x 75 FHB II-A S M16 x 95 FHB II-A S M20 x 170 FHB II-A S M24 x 170 *) max number with one static mixer 10 Drill hole diameter Min drill hole depth [mm] [mm] 10 10 12 16 25 25 75 90 90 110 190 190 Resin volume in scale units shown on the cartridge labels‘ corresponding scala Anchor per cartridge FIS HB 345 S *) 4 26 26 56 42 42 21 6 FIS A with Injection resin for aerated concrete Chemical fixings Secure hold in aerated concrete using undercut technology Canopies Detail: Undercut drillhole in aerated concrete VERSIONS APPROVALS ▪ zinc-plated steel ▪ stainless steel BUILDING MATERIALS Approved for: ▪ Reinforced roof and ceiling boards made of aerated concrete ▪ Aerated concrete blocks ▪ Prefabricated reinforced and nonreinforced wall components made of aerated concrete ADVANTAGES APPLICATIONS FUNCTIONING ▪ The cone-shaped drill hole guarantees maximum load-bearing capacity in aerated concrete thanks to the interlock ▪ The centring sleeve PBZ fixes the anchor in the drill hole, thus also allowing for overhead installation ▪ Two anchorage depths in combination with the threaded rod FIS  A allow for the ideal adaptation to the load to be applied ▪ The internal threaded anchor FIS  E allows for surface flush removal and reuse of the fixing point, and therefore offers the best possible flexibility ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ The system can be used with any of the following injection resins: FIS  V, FIS VS, FIS VW FIS VT and FIS P can be used but not have approvals ▪ The injection system for aerated concrete is for pre-positioned installation ▪ The cone drill bit PBB allows for the drill hole and undercut to be made in one step by pivoting the drill ▪ The resin completely fills the undercut and transfers the load via the interlock ▪ The drill hole is filled from the drill hole mouth using the centring sleeve PBZ ▪ The threaded rod FIS A or the internally threaded anchor FIS E are set manually by rotating slightly whilst pressing in INSTALLATION 74 Guard rails Consoles Gates Staircases Windows Faỗades Canopies Timber constructions Steel constructions Sun protection FIS A with Injection resin for aerated concrete TECHNICAL DATA Chemical Fixings Threaded rod FIS A Item FIS A M x 90 FIS A M x 110 FIS A M x 130 FIS A M x 175 FIS A M 10 x 110 FIS A M 10 x 130 FIS A M 10 x 150 FIS A M 10 x 170 FIS A M 10 x 200 FIS A M 12 x 120 FIS A M 12 x 140 FIS A M 12 x 160 FIS A M 12 x 180 FIS A M 12 x 210 FIS A M 12 x 260 stainless steel Art.-No gvz Art.-No A4 090274 090275 090276 090277 090278 090279 090281 044969 090282 044971 090283 090284 090285 090286 090287 090440 090441 090442 090443 090444 090447 090448 044973 090449 044974 090450 090451 090452 090453 090454 Drill hole diame- Min anchorage Max useful Fill quantity for ter in aerated depth in aerated length in aerated effect anchoring concrete concrete concrete depth in aerated concrete hef, tfix, max DIBt [mm] [mm] [mm] [scale units] Sales unit Approval Items to order only zinc plated, steel grade 5.8 ▯ ▯ ▯ ▯ ▯ ▯ ▯ ▯ ▯ ▯ ▯ ▯ ▯ ▯ ▯ 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 75 75 75 75 75 75 75 75 75 75 75 75 75 75 75 25 45 90 25 45 65 85 115 30 50 70 90 115 170 [pcs] 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 TECHNICAL DATA Items to order only Item FIS E 11 x 85 M6 FIS E 11 x 85 M8 zinc-plated steel Art.-No gvz 043631 043632 Approval Internal threaded sockets FIS E Drill hole diameter Effect anchoring depth hef Min bolt penetration lE,min Max bolt penetration lE,max Fill quantity for effect anchoring depth in aerated concrete Sales unit DIBt [mm] [mm] [mm] [mm] [scale units] [pcs] ▯ ▯ 14 14 85 85 60 60 20 20 10 10 ACCESSORIES Approval Cone drill PBB Item Cone drill PBB Centring sleeve PBZ Art.-No 090634 090671 DIBt ▯ ▯ Centring sleeve PBZ Fits Sales unit [pcs] M8 - M12; FIS E M8 - M12; FIS E 10 75 FIS A with Injection resin for aerated concrete Chemical fixings LOADS Injection system FIS V, FIS VS and FIS VW with threaded rod FIS A5) resp internal threaded socket FIS E5) and centring sleeve PBZ Highest permissible loads1) 6) for a single anchor in aerated concrete walls For the design the complete approval Z-21.3-1824 has to be considered Type Effective anchorage depth4) hef [N/mm²] [mm] Brick type, Installation torque naming acc DIN [-] Tinst [-] Permissible load3) Fperm [Nm] Aerated concrete block PB, PP M8 - M12 75 PB, PP 10,0 PB, PP 10,0 M8 - M12 954) M8 - M12 75 PB, PP 10,0 PB, PP 10,0 M8 - M12 954) M8 - M12 75 PB, PP 10,0 PB, PP 10,0 M8 - M12 954) Reinforced aerated concrete wall panel P / Reinforced aerated concrete roof and floor slabs M8 - M12 2,2 75 P2,2 10,0 P2,2 10,0 M8 - M12 2,2 954) M8 - M12 3,3 75 P3,3 10,0 P3,3 10,0 M8 - M12 3,3 954) M8 - M12 4,4 75 P4,4 10,0 P4,4 10,0 M8 - M12 4,4 954) 1) 2) 3) 76 Compressive brick strength fb Required safety factors are considered Minimum possible axial spacings resp edge distance while reducing the permissible load Valid for tensile load, shear load and oblique load under any angle For combinations of tensile loads, shear loads, bending moments as well as reduced edge distances or spacings (anchor groups) see approval 4) 5) 6) Aerated concrete wall Min Min spacing2) edge distance2) smin (amin) cmin (ar) [kN] [mm] [mm] 0,90 1,30 1,20 1,70 1,60 2,10 50 50 50 50 50 50 100 150 100 150 100 150 0,90 1,40 1,20 1,60 1,40 1,90 50 50 50 50 50 50 100 150 100 150 100 150 Values apply to threaded rod FIS A When using the internal threaded socket FIS E (M6 and M8) the anchorage depth is 85 mm instead of 95 mm gvz and A4 For FIS E screw with grade 5.8 resp A4-70 The given loads are valid for fixations in dry and humid aerated concrete for temperatures in the substrate up to +50°C (resp short term up to 80°C) and best possible drillhole cleaning according approval Rebar connections Professional rebar connections Rebar connections BUILDING MATERIALS APPROVALS Chemical Fixings Rebar connections Approved for: ▪ Concrete C12/15 to C50/60, cracked and non-cracked ADVANTAGES ▪ The injection resin FIS V / VS allow for rebar connections from Ø8 to 28 mm, whilst injection resin FIS EM allows for rebar connections up to Ø40 mm to be carried out This offers maximum flexibility ▪ FIS EM also allows for the execution of rebar connections in diamond-drilled holes ▪ The FRA with connecting thread in A4 stainless steel fully utilises the load-bearing capacity of the concrete This means that extremely high tensile loads can be introduced into the base material ▪ Accessories in line with building site requirements, such as injection adapters and extension tubes, ensure fast installation ▪ The FIS rebar case contains all of the individual components required, thus ensuring a convenient installation APPLICATIONS FUNCTIONING ▪ Post-installed concrete steel bars, e.g for overlap connections, end anchorings, starter bars, needlings etc ▪ Rebar anchor FRA ▪ Anchoring as with cast-in reinforcement bars in line with Eurocode and DIN 1045-1 ▪ The resin is extruded fully mixed into the drill hole using the injection adapter to prevent any air pockets The geometry causes a build-up of pressure in the drill hole, which pushes the injection adapter and extension tube automatically out of the drill hole ▪ The resin bonds the entire surface of the reinforcement bar with the drill hole wall INSTALLATION WITH FIS V / FIS VS INSTALLATION IN DIAMOND DRILLED HOLES WITH FIS EM INSTALLATION IN HAMMER DRILLED HOLES WUTH FIS EM 77 Rebar connections Rebar anchor FRA Combination of materials Approval Chemical fixings TECHNICAL DATA DIBt ETA Art.-No Total length Max fixing thickness Drill-hole l tfix d0 Fill quantity Sales unit [mm] [mm] [Ø mm] [scale units] [pcs] 975 1180 1485 60 60 60 16 20 25 50 81 160 8 Item FRA 12/900 M12-60 FRA 16/1100 M16-60 FRA 20/1400 M20-60 505529 505533 505534 ▯ ▯ ▯ ■ ■ ■ Reinforcement bar welded with the threaded part made of stainless steel A4 TECHNICAL DATA Approval Item Art.-No FIS-Rebar case Int 505942 Contents Sales unit DIBt ETA — ■ [pcs] x Cleaning brush, x Extensions for cleaning brushes 40 cm long, x SDS Chuck with internal thread M 8, 24 x Injection adapter, x Cleaning hose complete, x Brush control template, x Cleaning nozzle, x Marker tape, x Digital thermometer, x Protective goggles, x Installation instructions (german, english, french, italian, spanish), 10 x Installation report, x Flat spanner SW and the relevant approvals DISPENSER GUNS Dispenser FIS DC S Dispenser FIS AP To order only Item Dispenser FIS DP S-L Adapted for Dispenser FIS DPS/XL Performance data Art.-No Sales unit [pcs] FIS DC S FIS HB 345 S, FIS SB 390 S, FIS PB 360 S, 513423 FIS EM 390 S, FIS V 360 S, FIS P 300 T, FIS VS 150 C and Silicone cartridges Charger DCC 4000 507791 Battery pack DC 507792 FIS AP FIS V 360 S, FIS HB 345 S, FIS SB 390 S, FIS PB 058027 360 S, FIS HB 150 C, FIS EM 390 S, FIS VS 150 C, FIS VW 360 S, FIS P 300 T, and 1K-cartridge FIS DP S-L 511125 FIS EM 585 S FIS AJ 016251 FIS V 950 S FIS DPS/XL 512401 1500ml Shuttle cartridges i.e FIS EM 1500 Use with charger DCC 4000 / battery pack DC - Charger 12 V // 230 V Euro plug - Battery pack 12 V // 2,0 Ah // Ni-MH Recommended pressure bar Air compression Max 40I/min For the full range of Dispenser Guns please refer to page 39 78 Dispenser FIS AJ Recommended pressure bar air consumption Max 40I/min Recommended pressure bar air consumption Max 40I/min Recommended pressure bar air consumption Max 40I/min 1 Rebar connections DISPENSER GUNS Dispenser FIS AM To order only Item Art.-No FIS DM S 511118 FIS AM 056052 FIS DM S-L 510992 Dispenser FIS DM S-L Adapted for Sales unit [pcs] FIS SB 390 S, FIS PB 360 S, FIS V 360 S, FIS HB 345 S, FIS EM 390 S, FIS VS 150 C, FIS VW 360 S,FIS P 360 S, FIS P 300 T and 1K-cartridges FIS V 360 S, FIS HB 345 S, FIS HB 150 C, FIS VT 300 T, FIS VS 150 C, FIS VW 360 S,FIS P 300 T and 1K-cartridges FIS EM 585 S 1 Chemical Fixings Dispenser FIS DM S ACCESSORIES Cleaning brush with thread M Colour Items to order only Item Art.-No Brush for drill-Ø 12 mm Brush for drill-Ø 14 mm Brush for drill-Ø 16 mm Brush for drill-Ø 18 mm Brush for drill-Ø 20 mm Brush for drill-Ø 25 mm Brush for drill-Ø 30 mm Brush for drill-Ø 35 mm Brush for drill-Ø 40 mm Brush for drill-Ø 45 mm Brush for drill-Ø 55 mm FIS brush extension SDS Chuck with internal thread M 001490 001491 001492 001493 001494 001495 090063 090071 505061 506254 505062 508791 511961 white blue red yellow green black grey brown - Length Sales unit [mm] [pcs] 420 - 1 1 1 1 1 1 ACCESSORIES Injection adapter for drill Ø 12 - 25 mm Extension tube Injection adapter  for drill Ø 30 - 55 mm Items to order only Item Injection-adapter (Ø 9) for drill-Ø 12 mm Injection-adapter (Ø for drill-Ø 14 mm Injection-adapter (Ø 9) for drill-Ø 16 mm Injection-adapter (Ø 9) for drill-Ø 18 mm Injection-adapter (Ø for drill-Ø 20 mm Injection-adapter (Ø 15) for drill-Ø 20 mm Injection-adapter (Ø 9) for drill-Ø 25 mm Injection-adapter (Ø 15) for drill-Ø 25 mm Injection-adapter (Ø 9) for drill-Ø 30 mm Injection-adapter (Ø 15) for drill-Ø 30 mm Injection-adapter (Ø 9) for drill-Ø 35 mm Injection-adapter (Ø 15) for drill-Ø 35 mm Injection-adapter (Ø 9) for drill-Ø 40 mm Injection-adapter (Ø 15) for drill-Ø 40 mm Injection-adapter (Ø 9) for drill-Ø 45 mm Injection-adapter (Ø 15) for drill-Ø 45 mm Injection-adapter (Ø 9) for drill-Ø 55 mm Injection-adapter (Ø 15) for drill-Ø 55 mm FIS Extension tube Extension tube Ø 15 (1,9 m) Art.-No Colour Sales unit [pcs] 001497 001498 001499 001483 001506 001508 001507 001509 090689 090700 090699 090701 505077 505079 508909 508910 505078 505080 048983 001489 white blue red yellow green green black black grey grey brown brown - 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 79 Rebar connections Chemical fixings ACCESSORIES Compressed air nozzle Items to order only Item Art.-No Compressed air nozzle D12-D15 Compressed air nozzle D16-D19 Compressed air nozzle D20-D25 Compressed air nozzle D30-D35 Compressed air nozzle D40-D55 511956 511957 511958 511959 511960 Fits Sales unit [pcs] Drill diameter Ø 12 - 15 mm Drill diameter Ø 16 - 19 mm Drill diameter Ø 20 - 25 mm Drill diameter Ø 30 - 35 mm Drill diameter Ø 40 - 45 mm 2 2 LOADS Injection system FIS V, FIS VS and FIS EM with Rebars from steel type BSt 500 S5) Design resistant loads and permissible tensile loads1) 6) of a single post-installed Rebar in concrete C20/252) For the design and planning the complete approval ETA - 09/0089 and ETA - 08/0266 have to be considered Rebar Ø mm Ø 10 mm Ø 12 mm Ø 14 mm Ø 16 mm Ø 20 mm Ø 25 mm Ø 28 mm Ø 32 mm Ø 36 mm Ø 40 mm 1) 2) 3) 4) 5) Cracked or Non-cracked concrete Max design resistance Max permissible for tensile load tensile load NRd,s3) Nperm,s3) Basic anchorage length4) for FIS V, FIS VS lb,rqd Basic anchorage length4) for FIS EM lb,rqd [mm] [mm] [mm] [kN] [kN] 378 473 567 662 756 945 1181 1323 - 378 473 567 662 756 945 1181 1323 1512 1701 1890 1800 1800 1800 1800 1800 1800 2000 2000 2000 2000 2000 21,9 34,1 49,2 66,9 87,4 136,6 213,4 267,7 349,7 442,6 546,4 15,6 24,4 35,1 47,8 62,4 97,6 152,4 191,2 249,8 316,1 390,3 The partial safety factors for material resistance as regulated in the European Standard EN 19921-1 as well as a partial safety factor for load actions of JL = 1,4 are considered The ETA-approvals for FIS V and FIS EM allow post-installed rebar connections in concrete C12/15 up to C50/60 When using another concrete strength class the given basic anchorage length will change When using the full steel capacity Basic anchorage length" according EN 1992-1-1, chapter 8.4.3 for concrete strength class C20/25 for "good bond conditions" Rebars with a characteristic yield strength fyk = 400 - 600 N/mm² according EN 1992-1-1 6) 7) Max permissible embedment depth max lv Annex C,Table C.1 and C.2N are permitted When using an other steel quality the given basic anchorage length as well as the steel capacity (see foot note 3) will change Fixations with post-installed rebars with FIS V and FIS EM are permitted in dry and wet concrete for temperatures in the substrate up to +50°C (resp short term up to 80°C) and best possible drillhole cleaning according approval For determination of the installation measures (minimum concrete cover, spacings e.g.) as well as an eventually required transverse reinforcement see EN 1992-1-1 and the general instruction rules of the approvals LOADS Injection system FIS V, FIS VS and FIS EM with Rebar anchor FRA5) Highest permissible tensile loads1) 6) for a single Rebar anchor in concrete C20/252) For the design and planning the complete approvals ETA - 09/0089 and ETA - 08/0266 have to be considered Type FRA 12/900 M12 FRA 16/1100 M16 FRA 20/1400 M20 1) 2) 3) 4) 80 Cracked or Non-cracked concrete Installation torque Max design resistance Max permissible for tensile load tensile load Tinst NRd,s3) Nzul,s3) Basic anchorage length4) lb,rqd Max effective embedment depth max lv Max embedment depth max le,ges [mm] [mm] [mm] [Nm] [kN] [kN] 567 756 945 800 1000 1300 900 1100 1400 50,0 100,0 150,0 49,2 87,4 136,6 35,1 62,4 97,6 The partial safety factors for material resistance as regulated in the European Standard EN 19921-1 as well as a partial safety factor for load actions of JL = 1,4 are considered The ETA-approvals for FIS V and FIS EM allow post-installed rebar connections in concrete C12/15 up to C50/60 When using another concrete strength class the given basic anchorage length will change When using the full steel capacity Basic anchorage length according EN 1992-1-1, chapter 8.4.3 for concrete strength class C20/25 for „good bond conditions“ 5) 6) 7) Reinforcement bar BSt 500 S according EN 1992-1-1 Annex C,Table C.1 and C.2N Fixations with post-installed Rebars anchors FRA with FIS V and FIS EM are permitted in dry and wet concrete for temperatures in the substrate up to +50°C (resp short term up to 80°C) and best possible drillhole cleaning according approval For determination of the installation measures (minimum concrete cover, spacings e.g.) as well as an eventually required transverse reinforcement see EN 1992-1-1 and the general instruction rules of the approvals Highbond anchor dynamic FHB dyn The performance class amongst dynamic anchors Tunnel ventilators VERSIONS APPROVALS Chemical Fixings Production robots ▪ zinc-plated steel ▪ high corrosion resistant steel BUILDING MATERIALS Approved for: ▪ Concrete C20/25 to C50/60, cracked and non-cracked ADVANTAGES APPLICATIONS FUNCTIONING ▪ During the setting process, the injection resin FIS  HB fills the annular gap in the fixture, and ensures maximum load distribution This allows for the absorption of dynamic alternating loads ▪ The cone shape of the FHB-A dyn rod ensures controlled expansion under dynamic stress, thus allowing for use in cracked concrete ▪ The FHB-A  dyn is also available in highly corrosion-resistant steel This makes it suitable for use in aggressive atmospheres such as tunnels ▪ The Highbond anchor dynamic system can achieve even greater shear loads due to the additional sleeve of the anchor rod FHB-A dyn V and therefore provides an increased level of safety ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ The injection system suitable for tensile zones consists of the Highbond dynamic anchor rod FHB-A  dyn and the injection resin FIS HB ▪ FHB dyn is approved for pre-positioned and push-through installation ▪ Extruding the resin causes the two components to be mixed and activated in the static mixer ▪ The resin bonds the entire surface of the anchor rod with the drill hole wall and seals the drill hole ▪ The centring sleeve positions the anchor in the middle of the fixture, thus ensuring a safe load application ▪ The lock nut prevents the nut from becoming loose Cranes Mobile portal and ceiling cranes Guide rails for elevators Tunnel ventilators (jet fans) Bridges for traffic signs Antennas and transmitter masts Industrial robots PRE-POSITIONED INSTALLATION FHB DYN PUSH-THROUGH INSTALLATION FHB DYN / FHB DYN V 81 Highbond anchor dynamic FHB dyn Highbond anchor dynamic FHB-A dyn highly corrosion resistant steel Art.-No C zinc-plated steel Items to order only Art.-No gvz Item FHB-A dyn 12 x 100/25 FHB-A dyn 12 x 100/50 FHB-A dyn 16 x 125/25 FHB-A dyn 16 x 125/50 FHB-A dyn 20 x 170/50 FHB-A dyn 24 x 220/50 092018 092019 092020 092036 092037 092038 Anchorage depth Drill depth through fixture h0 hef Min - max Fixture thickness tfix DIBt [mm] [mm] [mm] [mm] [Ø mm] [mm] [pcs] ▯ ▯ ▯ ▯ ▯ ▯ 14 14 18 18 24 28 130 155 155 180 225 275 100 100 125 125 170 220 - 25 - 50 10 - 25 10 - 50 12 - 50 14 - 50 15 15 19 19 25 29 19 19 24 24 30 36 10 10 10 10 10 Approval Chemical fixings TECHNICAL DATA — — — 093445 1) — — Drill hole diameter Drill-hole Width across diameter in nut object df  SW Sales unit 1) Prices and delivery time on request TECHNICAL DATA Highbond anchor dynamic FHB-A dyn V zinc-plated steel Art.-No gvz Item td hef tfix Drill-hole diameter in object df DIBt [mm] [mm] [mm] [mm] [Ø mm] [mm] [pcs] ▯ ▯ 14 18 85 100 105 130 - 50 10 - 50 21 29 19 24 10 10 Approval Items to order only FHB-A dyn 12 x 100/50 V 092039 FHB-A dyn 16 x 125/50 V 092040 Drill hole diameter Drilldepth Anchorage depth Min - max Fixture thickness Width across nut Sales unit  SW TECHNICAL DATA Approval Injection resin FIS HB 345 S + static mixer  FIS S Item Art.-No FIS HB 345 S FIS Mixer red 033211 096448 Languages on the cartridge Contents Sales unit D, GB, F, E, NL, CZ — cartridge 360 ml, x static mixer FIS S 10 static mixer DIBt ▯ — [pcs] CURING TIME - FIS HB Cartridge temperature FIS HB (minimum + 5°C) + 5°C – +20°C +20°C – +30°C +30°C – +40°C     > +40°C Gelling time FIS HB Temperature at anchoring base Curing time 15  6  4  2 ‒ 5°C – ± 0°C ± 0°C – + 5°C + 5°C – +20°C +20°C – +30°C +30°C – +40°C     > +40°C 360 180  90  35  20  12 FIS HB Please note: The curing times apply for dry anchoring bases, in damp anchoring bases they should be doubled Remove water from drill hole 82 10 Highbond anchor dynamic FHB dyn FILLING QUANTITIES Resin volume in scale units shown on the cartridge labels‘ corresponding scale Anchors per cartridge FIS HB 345 S *) 10 23 38 12 20 24 21 18 17 14 FHB-A dyn 12 x 100 / 25 FHB-A dyn 12 x 100 / 50 FHB-A dyn 16 x 125 / 25 FHB-A dyn 16 x 125 / 50 FHB-A dyn 20 x 170 / 50 FHB-A dyn 24 x 220 / 50 FHB-A dyn 12 x 100 / 50 V FHB-A dyn 16 x 125 / 50 V Chemical Fixings Type *) max number with one static mixer DISPENSER GUNS Dispenser FIS DM S To order only Item Dispenser FIS AM Adapted for Sales unit Art.-No FIS DM S 511118 FIS AM 056250 [pcs] FIS SB 390 S, FIS PB 360 S, FIS V 360 S, FIS HB 345 S, FIS EM 390 S, FIS VS 150 C, FIS VW 360 S,FIS P 360 S, FIS P 300 T and 1K-cartridges FIS V 360 S, FIS HB 345 S, FIS HB 150 C, FIS VT 300 T, FIS VS 150 C, FIS VW 360 S, FIS P 300 T and 1K-cartridges 1 DISPENSER GUNS Dispenser FIS DC S Dispenser FIS AP Adapted for To order only Item Performance data Art.-No Sales unit [pcs] FIS DC S FIS HB 345 S, FIS SB 390 S, FIS PB 360 S, 513423 FIS EM 390 S, FIS V 360 S, FIS P 300 T, FIS VS 150 C and Silicone cartridges Charger DCC 4000 507791 Battery pack DC 507792 FIS AP FIS V 360 S, FIS HB 345 S, FIS SB 390 S, FIS PB 058027 360 S, FIS HB 150 C, FIS EM 390 S, FIS VS 150 C, FIS VW 360 S, FIS P 300 T, and 1K-cartridge Use with charger DCC 4000 / battery pack DC - Charger 12 V // 230 V Euro plug - Battery pack 12 V // 2,0 Ah // Ni-MH Recommeneded pressure bar Air compression Max 40I/min For the full range of Dispenser Guns please refer to page 39 83 Highbond anchor dynamic FHB dyn Chemical fixings DRILL HOLE CLEANING ACCESSORIES Cleaning brush BS for concrete Item BS ø 14 BS ø 16/18 BS ø 24 BS ø 28 For drill diameter Brush diameter [mm] [mm] 14 16/18 24 28 16 20 26 30 Art.-No 078180 078181 078182 078183 Fits to fixings Sales unit [pcs] FHB-A dyn M12 FHB-A dyn M16 FHB-A dyn M20 FHB-A dyn M24 1 1 Compressed-air cleaning gun Item to order only Sales unit Fits Item Art.-No Compressed-air cleaning gun ABP 059456 [pcs] FHB-A dyn M20-M24 1 LOADS Highbond anchor dynamic FHB dyn Highest permissible loads for a single anchor1) 6) in concrete B25 resp C20/254) For the design the complete approval Z-21.3-1748 has to be considered Type FHB dyn 12x100 FHB dyn 12x100 V FHB dyn 16x125 FHB dyn 16x125 V FHB dyn 16x125 C 5) FHB dyn 20x170 FHB dyn 24x220 1) 2) 84 Min member thickness hmin Installation torque Tinst [mm] [mm] [Nm] [kN] [kN] [mm] [mm] 100 105 125 130 125 170 220 200 200 250 250 250 340 440 40,0 40,0 60,0 60,0 60,0 100,0 120,0 14,1 14,1 23,0 23,0 15,6 28,1 28,9 6,7 9,6 11,9 17,0 11,9 17,0 22,2 100 100 100 100 100 150 180 100 100 100 100 100 150 180 The permissible loads apply for the design method II (unknown lowest load and unknown load cycles) The partial safety factor for material resistance and the partial safety factor for action regarding fatigue as regulated in the approval are considered When using design method I higher permissible loads may be possible As an single anchor counts e.g an anchor with a spacing s • x hef and an edge distance c • 1,5 x hef Accurate data see approval Minimum possible axial spacings resp edge distance while reducing the permissible load 3) 4) 5) 6) Permissible tensile load ∆Nzul3) Cracked or Non-cracked concrete Permissible Min shear load spacing ∆Vzul3) smin2) Effective anchorage depth hef Min edge distance cmin2) For combinations of tensile loads, shear loads as well as reduced edge distances or spacings (anchor groups) see approval For higher concrete strength classes up to C50/60 higher permissible loads may be possible Anchor rod FHB-A dyn-C made of highly corrosion-resistant steel of the corrosion resistance class IV e.g 1.4529 The given loads are valid for fixations in dry and humid concrete for temperatures in the substrate up to +50°C (resp short term up to 80°C) and best possible drillhole cleaning according approval fill & fix injection fixing A versatile injection fixing Chemical Fixings Repairing damaged curtain rails Repairing damaged curtain rails BUILDING MATERIALS ▪ Concrete ▪ Vertically perforated brick ▪ Hollow block made from lightweight concrete ▪ Cavity floor slabs made of brick, concrete, etc ▪ Perforated sand-lime brick ▪ Solid sand-lime brick ▪ ▪ ▪ ▪ ▪ Natural stone with dense structure Panel building materials Aerated concrete Solid panel made from gypsum Solid brick made from lightweight concrete ▪ Solid brick ADVANTAGES APPLICATIONS FUNCTIONING ▪ The fill & fix injection fixing works in most building materials As a result, a number of applications can be completed with just one product ▪ Wood screws can be screwed directly into the hardened injection fixing for a fast and simple installation ▪ The special formula compound enables the screw to be screwed into the injection fixing and removed so components can be reattached to the same point ▪ fill & fix can be sanded, painted, and is suitable for filling drill holes that are no longer needed prior to painting ▪ Repairing cracked or over-sized drill holes ▪ Repairing broken furniture hinges etc ▪ Fixing lightweight objects in difficult or old building materials ▪ Fixing lightweight objects in internal and UV-protected external areas ▪ fill & fix is a 2-component, solventfree injection compound based on polyurethane It is applied into the drill hole, where it foams lightly and sets quickly ▪ The increase in volume during the setting process guarantees a secure hold, even in old or difficult building materials ▪ After approx 2 minutes, screws, hooks, eye screws etc, with a diameter of up to 6 mm that are normally used in wood, can be screwed into and removed from the set material without pre-drilling ▪ Use the perforated sleeves (included) for hollow and board building materials INSTALLATION TECHNICAL DATA fill & fix Injection fixing Items to order only Item fill & fix K (GB) fill & fix (GB) fill & fix Static mixer Art.-No 504429 503463 502735 Contents cartridge 25 ml, static mixer, anchor sleeves, extension tubes cartridge 25 ml, static mixer, anchor sleeves, extension tubes static mixer Languages on the cartridge Sales unit [pcs] GB GB - 12 85 86 Chemical fixings Decisive factors Technical disclaimer / Decisive factors This document is a factual record of anchor performance obtained under specific conditions and does not constitute an endorsement of the suitability of the product for any specific application This responsibility remains with the customer The data given shall be used as a guide for assessment or anchor suitability Even when our advice is given in good faith it cannot be binding for this reason and we cannot accept any liability for any anchor failure due to the wrong design, misuse or wrong installation For safety critical applications only anchors with an ETA or Zulassung German Approval shall be used Chemical Fixings Due to the complexity of building materials, tools, fixing elements and installation techniques a comprehensive recommendation depends on full and detailed understanding of specific site conditions For further product information please contact the fischer Technical Department: Phone: 01491 827 920 E-mail: technical@fischer.co.uk fischer fixings (UK) Ltd Whitely Road, Wallingford, Oxon, OX10 9AT We cannot be responsible for any errors, and we reserve the right to make technical and range modifications without notice No liability is accepted for printing errors and omissions General Notice The information in this brochure is intended for general guidance only and is given without engagement Additional information and advice on specific applications is available from our Technical Support Team For this however, we require a precise description of your particular application All the data in this brochure concerning work with our fixings must be adapted to suit local conditions and the type of materials in use If no detailed performance specifications are given for certain articles and types, please contact our Technical Service Department for advice Phone: 01491 827 920 E-mail: technical@fischer.co.uk 87 01/2013 fischer fixings UK Ltd Whitely Road Oxon OX10 9AT Wallingford Great Britain Phone (0044) 1491 827900 Fax (0044) 1491 827953 E-mail info@fischer.co.uk www.fischer.co.uk Technical Service If you need any assistance, simply contact your local fischer representative For more specialised application problems please contact our Technical Services Team Your dealer: fischer fixings UK Ltd Wallingford, Oxon, OX10 9AT Phone e-mail: 01491 827 920 technical@fischer.co.uk Technical Training We also offer training seminars suited to your individual needs and requirements Please call the number above to find out more www.fischer.co.uk Chemical fixings / of 12 Product sections / 01/2013 · (V1) · Printed in the UK Contacts ... 6 10 10 10 10 10 37 57 77 97 11 7 12 7 32 52 72 92 11 2 12 2 17 2 14 59 84 13 4 18 4 96 11 6 12 0 12 0 12 0 12 0 10 3 12 3 14 3 14 4 14 4 14 4 14 4 10 9 15 4 17 9 19 2 19 2 8 8 11 12 12 12 12 12 12 18 18 18 18 1 17... 20/E 24 1xRSB 20/E 24 1xRSB 20/E 24 1xRSB 20/E 24 1xRSB 20/E 24 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 FIS... 1xRSB 1xRSB 10 1xRSB 10 1xRSB 10 1xRSB 10 1xRSB 10 1xRSB 10 1xRSB 10 1xRSB 12 1xRSB 12 1xRSB 12 15 0 15 0 15 0 15 0 15 0 15 0 15 0 15 0 15 0 15 0 15 0 15 0 15 0 15 0 19 0 19 0 19 0 19 0 19 0 19 0 19 0 210 210 210 210