8600 Smart Routers Performance Counters Reference Guide 76.8600-50143G 28.04.2015 Document Information Revision History Document No Date Description of Changes 76.8600-50143G 28.04.2015 FP7.0 updates for the following network elements: • 8602 Smart Router • 8609 Smart Router • 8611 Smart Router • 8615 Smart Router • 8630 Smart Router • 8660 Smart Router • 8665 Smart Router 76.8600-50143F 23.10.2014 • 8602 Smart Router FP1.1 • 8609 Smart Router and 8611 Smart Router FP2.0 • 8615 Smart Router FP1.0 • 8630 Smart Router and 8660 Smart Router FP5.0 Supported cards are specified per counter for 8630 Smart Router and 8660 Smart Router 76.8600-50143E 13.05.2014 Updates added for: • 8602 Smart Router FP1.0 • 8609 Smart Router and 8611 Smart Router FP1.3 8600 Smart Routers Performance Counters Reference Guide 76.8600-50143G © 2015 Coriant This revision of the manual documents the following network elements and the corresponding feature packs or higher 8602 Smart Router FP7.0 8605 Smart Router FP1.6 8607 Smart Router FP1.1 8609 Smart Router, 8611 Smart Router FP7.0 8615 Smart Router FP7.0 8620 Smart Router FP4.1 8630 Smart Router, 8660 Smart Router FP7.0 8665 Smart Router FP7.0 If a different feature pack of 8600 products, please refer to the relevant product document program on the Tellabs and Coriant Portal by navigating to www.portal.tellabs.com > Product Documentation > Data Networking > Tellabs 8600 Smart Routers > Technical Documentation The functionality described in this document for 8615 Smart Router is also applicable to 8615 Smart Router stacked, unless otherwise stated © 2015 Coriant All rights reserved This manual is protected by U.S and international copyright laws, conventions and treaties Your right to use this manual is subject to limitations and restrictions imposed by applicable licenses and copyright laws Unauthorized reproduction, modification, distribution, display or other use of this manual may result in criminal and civil penalties The specifications and information regarding the products in this manual are subject to change without notice All statements, information, and recommendations in this manual are believed to be accurate but are presented without warranty of any kind, express or implied Users must take full responsibility for their application of any products Adobe ® Reader ® are registered trademarks of Adobe Systems Incorporated in the United States and/or other countries 76.8600-50143G © 2015 Coriant 8600 Smart Routers Performance Counters Reference Guide 8600 Smart Routers Performance Counters Reference Guide 76.8600-50143G © 2015 Coriant Document Information Terms and Abbreviations 76.8600-50143G © 2015 Coriant Term Explanation AAL ATM Adaptation Layer Abis The interface between the base station controller and mobile switching center ACG Abis Compression Group AIS Alarm Indication Signal ANSI American National Standards Institute APS Automatic Protection Switching ATM Asynchronous Transfer Mode B8ZS Bipolar 8-Zero Substitution BW Bandwidth CBR Constant Bit Rate CESoPSN Circuit Emulation Service over Packet-Switched Network CFO Content Free Operation CLI Command Line Interface CP C-bit Parity CRC Cyclic Redundancy Check CU Control functionality (used in 8615 Smart Router and 8665 Smart Router) DS1 Digital Signal level (T1) DS3 Digital Signal level (T3) DSL Digital Subscriber Line E1 E-carrier in ETSI ES Error Seconds ESF Extended Super Frame ETSI European Telecommunications Standards Institute FC Failure Count FEBE Far End Block Error FP Feature Pack HDB3 High Density Bipolar 3-zeroes LOPS Loss of Packet Synchronization LOS Loss of Signal LOSW Loss of Sync Word LU1 Line unit in 8665 Smart Router M23 Specific DS3 Multiplexing Format MCR Minimum Cell Rate 8600 Smart Routers Performance Counters Reference Guide Document Information MSP Multiplexer Section Protection NE Network Element OOFS Out Of Framed Seconds P12x Unframed 2.048 kbps according to G.703 PCR Peak Cell Rate PDH Plesiochronous Digital Hierarchy PM Performance Monitoring PWE3 Pseudo Wire Emulation Edge to Edge REI Remote Error Indication SAToP Structure-Agnostic Time Division Multiplexing over Packet SCR Sustainable Cell Rate SDH Synchronous Digital Hierarchy SEF Severely Errored Framing SES Severely Errored Seconds SF Super Frame SHDSL Single-Line High-bit-rate Digital Subscriber Line SONET Synchronous Optical Network STS Synchronous Transport Signal SU1 Switch unit in 8665 Smart Router T1 T-carrier in ANSI TDM Time Division Multiplexing UAS Unavailable Seconds UBR Unspecified Bit Rate VBR Variable Bit Rate VC ATM Virtual Channel VCC Virtual Channel Connection 8600 Smart Routers Performance Counters Reference Guide 76.8600-50143G © 2015 Coriant Table of Contents Table of Contents About This Manual Objectives Audience 8600 Smart Routers Technical Documentation Document Conventions 12 Documentation Feedback 12 8600 Smart Routers Discontinued Products 13 Performance Counters 14 1.1 1.2 1.3 1.4 1.5 1.6 1.7 76.8600-50143G © 2015 Coriant Overview 14 Interface DSL Counters 14 1.2.1 Shdsl Segment Endpoint 14 Interface Ethernet Counters 15 1.3.1 Cfm Delay Measurement 15 1.3.2 Cfm Loss Measurement 17 Interface PDH Counters 18 1.4.1 Ds1 Line 18 1.4.2 P12 / Ds1 Path 19 1.4.3 Tdm Pw 20 1.4.4 Ds3 Path 22 1.4.5 Abis Group 24 Interface SDH Counters 26 1.5.1 Rs 26 1.5.2 Ms 27 1.5.3 Sts / Vt15 Path 28 Layer Tunneling Counters 29 1.6.1 Pwe3 Circuit 29 Node Testing and Measurement Counters 30 1.7.1 Power Consumption 30 1.7.2 CPU / Cache / Memory 31 1.7.3 NPU 32 8600 Smart Routers Performance Counters Reference Guide About This Manual About This Manual This chapter discusses the objectives and intended audience of the, 8600 Smart Routers Performance Counters Reference Guide and consists of the following sections: • Objectives • Audience • Related Documentation • Conventions • Documentation Feedback Objectives This reference manual provides an overview of the 8600 Smart Routers supported performance counters Audience This reference manual is intended for system specialists and personnel involved in network planning 8600 Smart Routers Technical Documentation The document numbering scheme consists of the document ID, indicated by numbers, and the document revision, indicated by a letter The references in the Related Documentation table below are generic and include only the document ID To make sure the references point to the latest available document versions, please refer to the relevant product document program on the Tellabs and Coriant Portal by navigating to www.portal.tellabs.com > Product Documentation & Software > Data Networking > 8600 Smart Routers > Technical Documentation The table below reflects the customer document content planned for SR7.0 GA, and is subject to change Before General Availability of SR7.0, the configuration guides have the status of draft, and they not always describe the full functionality 8600 Smart Routers Performance Counters Reference Guide 76.8600-50143G © 2015 Coriant About This Manual Document Title Description 8600 Smart Routers ATM and TDM Configuration Guide (76.8600-50110) Provides an overview of 8600 NEs PWE3 applications, including types, Single-Segment and Multi-Segment; PWE3 Redundancy; ATM applications, including PWE3 tunnelling, Traffic Management, Fault Management OAM, protection and TDM applications as well as instructions on how to configure them with CLI 8600 Smart Routers Boot and Mini-Applications Embedded Software Release Notes (76.8600-50108) Provides information related to the boot and mini-applications software of 8605 Smart Router, 8607 Smart Router, 8609 Smart Router, 8611 Smart Router, 8620 Smart Router, 8630 Smart Router and 8660 Smart Router as well as the installation instructions 8600 Smart Routers CLI Commands Manual (76.8600-50117) Provides commands available to configure, monitor and maintain 8600 system with CLI 8600 Smart Routers Embedded Software Release Notes 8600 Smart Routers SR7.0 Embedded Software Release Notes (76.8670-50177) for the following products: • 8602 Smart Router FP7.0 • 8609 Smart Router and 8611 Smart Router FP7.0 • 8615 Smart Router FP7.0 • 8630 Smart Router and 8660 Smart Router FP7.0 • 8665 Smart Router FP7.0 76.8600-50143G © 2015 Coriant 8600 Smart Routers Equipment Management Configuration Guide (76.8600-50118) Provides an overview of 8600 system HW inventory, software management, equipment protection 1+1 (CDC and SCM) as well as instructions on how to configure them with CLI 8600 Smart Routers Ethernet Configuration Guide (76 8600-50133) Provides an overview of 8600 system Ethernet applications, including interfaces; Ethernet forwarding (MAC Switching, Ethernet PWE3, IRB, VLAN, VPLS); Ethernet OAM; LAG; ELP as well as instructions on how to configure them with CLI 8600 Smart Routers Smart Routers Fault Management Configuration Guide (76.8600-50115) Provides an overview of 8600 system fault management, including fault source, types and status as well as instructions on how to configure it with CLI 8600 Smart Routers Frame Relay Configuration Guide (76.8600-50120) Provides an overview of 8600 system Frame Relay applications, including interfaces; Performance Monitoring; protection; Traffic Management as well as instructions on how to configure them with CLI 8600 Smart Routers Hardware Installation Guide (76.8600-40039) Provides guidance on mechanical installation, cooling, grounding, powering, cabling, maintenance, commissioning and ESW downloading 8600 Smart Routers Performance Counters Reference Guide About This Manual Document Title Description 8600 Smart Routers Network Interfaces Configuration Guide The Network Interfaces Configuration Guide provides an overview of the 8600 NEs interface functions, including NE supported interface types and equipping; interface features; configuration options and operating modes; fault management; performance monitoring; interface configuration layers and port protocols as well as instructions on how to configure them with CLI The following interface configuration guides are available: • 8600 Smart Routers Network Interfaces Configuration Guide (76.8600-50161) (for 8602 Smart Router, 8615 Smart Router and 8665 Smart Router) • 8609 Smart Router and 8611 Smart Router FP7.0 Interface Configuration Guide (76.8670-50179) • 8600 Smart Routers FP7.0 Interface Configuration Guide (76.8670-50180) (for 8630 Smart Router and 8660 Smart Router) 8600 Smart Routers IP Forwarding and Traffic Management Configuration Guide (76.8600-50122) Provides an overview of 8600 NEs IP, forwarding and traffic management functionality, including: IP addressing; IP hosting (ARP, DHCP); IP routing (static); ACL; Differentiated Services (Policing, Queue Management, Shaping) as well as instructions on how to configure them with CLI 8600 Smart Routers Management Communications Configuration Guide (76.8600-50125) Provides an overview of 8600 system management communications functions, including communication protocols: BMP; FTP; RADIUS; SNMP; SSH; TELNET as well as instructions for configuring them with CLI 8600 Smart Routers Mobile Optimization Configuration Guide (76.8600-50100) Provides an overview of 8600 system Mobile Optimization applications as well as instructions on how to configure them with CLI 8600 Smart Routers MPLS Applications Configuration Guide (76.8600-50123) Provides an overview of 8600 NEs MPLS applications (including FRR (one-to-one and facility backup); LDP; protection and Traffic Engineering), MPLS-TP applications (including OAM, linear protection), S-MPLS applications as well as instructions on how to configure them with CLI 8600 Smart Routers Performance Counters Reference Guide (76.8600-50143) Provides an overview of 8600 system supported performance counters 8600 Smart Routers Performance Counters Reference Guide 10 76.8600-50143G © 2015 Coriant Performance Counters CLI: show interface performance 76.8600-50143G © 2015 Coriant BMP Counter Description Support ([8660,8630 CDC1 / CDC2 / IFC1 / IFC2 / ELC1] / 8620 / 8602 / 8605 / 8607 / 8609 / 8611 / 8615 / [8665 vCU / LU1 / SU1]) jitterBufferUnderruns Number of times a packet needed to be played out and the jitter buffer was empty SNMP: draft-ietf-pwe3-tdm-mib-10 FP [- / - / 2.10 / 3.0 / -] / 2.10 / - / 1.2 / 1.0A / 1.0 / 1.1 / - [/ - / -] malformedPacketCount Number of packets detected with unexpected size, or bad headers' stack SNMP: draft-ietf-pwe3-tdm-mib-10 FP [- / - / 2.10 / 3.0 / -] / 2.10 / - / 1.2 / 1.0A / 1.0 / 1.1 / - [/ - / -] missingPackets Number of missing packets (as detected via control word sequence number gaps) SNMP: draft-ietf-pwe3-tdm-mib-10 FP [- / - / 2.10 / 3.0 / -] / 2.10 / - / 1.2 / 1.0A / 1.0 / 1.1 / - [/ - / -] misOrderDropped Number of packets detected out of order (via control word sequence numbers), and could not be re-ordered, or could not fit in the jitter buffer SNMP: draft-ietf-pwe3-tdm-mib-10 FP [- / - / 2.10 / 3.0 / -] / 2.10 / - / 1.2 / 1.0A / 1.0 / 1.1 / - [/ - / -] packetsReOrder Number of packets detected out of sequence (via control word sequence number), but successfully re-ordered SNMP: draft-ietf-pwe3-tdm-mib-10 FP [- / - / 2.10 / 3.0 / -] / 2.10 / - / 1.2 / 1.0A / 1.0 / 1.1 / - [/ - / -] jitterBufferOverruns Jitter buffer overruns (based on Sequence Number) This field is incremented upon state change; the second packet dropped due to overrun will increment the overrun packets counter FP [- / - / 2.10 / 3.0 / -] / 2.10 / - / 1.2 / 1.0A / 1.0 / 1.1 / - [/ - / -] duplicatePackets Packets that were dropped because they were previously received and enqueued (based on Sequence Number) FP [- / - / 2.10 / 3.0 / -] / 2.10 / - / 1.2 / 1.0A / 1.0 / 1.1 / - [/ - / -] controlWordAisDropped Number of packets that were dropped due to L=1 M=0 in the PWE3 control word (Invalid data -> switch to AIS) FP [- / - / 2.10 / 3.0 / -] / 2.10 / - / 1.2 / 1.0A / 1.0 / 1.1 / - [/ - / -] es Number of Errored Seconds encountered Any malformed packet, sequence error, LOPS, and the like are considered as Errored Seconds SNMP: draft-ietf-pwe3-tdm-mib-10 FP [- / - / 2.10 / 3.0 / -] / 2.10 / - / 1.2 / 1.0A / 1.0 / 1.1 / - [/ - / -] 8600 Smart Routers Performance Counters Reference Guide 21 Performance Counters 1.4.4 BMP Counter Description Support ([8660,8630 CDC1 / CDC2 / IFC1 / IFC2 / ELC1] / 8620 / 8602 / 8605 / 8607 / 8609 / 8611 / 8615 / [8665 vCU / LU1 / SU1]) ses Number of Severely Errored Seconds encountered 30 % or more of missing packets detected (consecutive or not) within a 1-second window cause a Severely Error Second (SES) to be counted SNMP: draft-ietf-pwe3-tdm-mib-10 FP [- / - / 2.10 / 3.0 / -] / 2.10 / - / 1.2 / 1.0A / 1.0 / 1.1 / - [/ - / -] uas The counter associated with the number of Unavailable Seconds encountered Any consecutive ten seconds of SES are counted as one UAS SNMP: draft-ietf-pwe3-tdm-mib-10 FP [- / - / 2.10 / 3.0 / -] / 2.10 / - / 1.2 / 1.0A / 1.0 / 1.1 / - [/ - / -] fc TDM Failure Counts (FC-TDM) The number of TDM failure events A failure event begins when the LOPS failure is declared, and it ends when the failure is cleared A failure event that begins in one period and ends in another period is counted only in the period in which it begins SNMP: draft-ietf-pwe3-tdm-mib-10 FP [- / - / 2.10 / 3.0 / -] / 2.10 / - / 1.2 / 1.0A / 1.0 / 1.1 / - [/ - / -] Ds3 Path This resource is used to hold the 15 and 24h current data and history register counts for framed DS3 layer Both GR-820 and G.826 PM primitives are supported CLI: show interface performance BMP Counter Description Support ([8660,8630 CDC1 / CDC2 / IFC1 / IFC2 / ELC1] / 8620 / 8602 / 8605 / 8607 / 8609 / 8611 / 8615 / [8665 vCU / LU1 / SU1]) neCv Count of P-bit parity errors FP [- / - / - / - / -] / - / - / 1.2 / - / - / - / - [/ - / -] neCvC Count of CP-bit parity errors This is not defined for M23 frame format FP [- / - / - / - / -] / - / - / 1.2 / - / - / - / - [/ - / -] neEs Number of P-bit Errored Seconds encountered (parity error >=1 or SEF >=1 or AIS >=1) FP [- / - / - / - / -] / - / - / 1.2 / - / - / - / - [/ - / -] 8600 Smart Routers Performance Counters Reference Guide 22 76.8600-50143G © 2015 Coriant Performance Counters 76.8600-50143G © 2015 Coriant BMP Counter Description Support ([8660,8630 CDC1 / CDC2 / IFC1 / IFC2 / ELC1] / 8620 / 8602 / 8605 / 8607 / 8609 / 8611 / 8615 / [8665 vCU / LU1 / SU1]) neEsC Number of CP-bit Errored Seconds encountered (CP-bit error >=1 or SEF >=1 or AIS >=1) FP [- / - / - / - / -] / - / - / 1.2 / - / - / - / - [/ - / -] neSes Number of P-bit Severely Errored Seconds encountered (parity error >=44 or SEF >=1 or AIS >=1) For M23 frame format this is undefined FP [- / - / - / - / -] / - / - / 1.2 / - / - / - / - [/ - / -] neSesC Number of CP-bit Severely Errored Seconds encountered (CP parity error >=44 or SEF >=1 or AIS >=1) For M23 frame format this is undefined FP [- / - / - / - / -] / - / - / 1.2 / - / - / - / - [/ - / -] neUas The number of P-bit Unavailable Seconds encountered FP [- / - / - / - / -] / - / - / 1.2 / - / - / - / - [/ - / -] neUasC The number of CP-bit Unavailable Seconds encountered For M23 frame format this is undefined FP [- / - / - / - / -] / - / - / 1.2 / - / - / - / - [/ - / -] neSef The primitive is a count of second intervals containing one or more SEFs or one or more AIS defects (SEF >=1 or AIS >= 1) FP [- / - / - / - / -] / - / - / 1.2 / - / - / - / - [/ - / -] feCv Far end code violations For M23 frame format this is undefined (Count of M frames with FEBE bit not equal 111) FP [- / - / - / - / -] / - / - / 1.2 / - / - / - / - [/ - / -] feEs Number of Errored Seconds encountered at Far End For M23 frame format this is undefined (FEBE >=1 OR SES/AIS >= 1) FP [- / - / - / - / -] / - / - / 1.2 / - / - / - / - [/ - / -] feSes Number of Severely Errored Seconds encountered at Far End For M23 frame format this is undefined (k M-frames with FEBE no equal 111, where k > 44 or SES/AIS >= 1)) FP [- / - / - / - / -] / - / - / 1.2 / - / - / - / - [/ - / -] feUas The number of Unavailable Seconds encountered at Far End For M23 frame format this is undefined (SEF >=1 or AIS >= 1) FP [- / - / - / - / -] / - / - / 1.2 / - / - / - / - [/ - / -] neAiss (gr820Ds3Primitives) The primitive is a count of second intervals when AIS was active (AIS >= 1) FP [- / - / - / - / -] / - / - / 1.2 / - / - / - / - [/ - / -] feSef (gr820Ds3Primitives) The primitive is a count of second intervals containing framing error in far-end For M23 frame format this is undefined FP [- / - / - / - / -] / - / - / 1.2 / - / - / - / - [/ - / -] 8600 Smart Routers Performance Counters Reference Guide 23 Performance Counters 1.4.5 BMP Counter Description Support ([8660,8630 CDC1 / CDC2 / IFC1 / IFC2 / ELC1] / 8620 / 8602 / 8605 / 8607 / 8609 / 8611 / 8615 / [8665 vCU / LU1 / SU1]) neBbe (gr826Primitives) Near-end errored blocks not occurring as part of an SES FP [- / - / - / - / -] / - / - / 1.2 / - / - / - / - [/ - / -] feBbe (gr826Primitives) Far-end errored blocks not occurring as part of an SES FP [- / - / - / - / -] / - / - / 1.2 / - / - / - / - [/ - / -] Abis Group This resource is used to hold the cumulative, 15 min, hour and 24h current and history data counts for Abis Group CLI: show interface performance 8600 Smart Routers Performance Counters Reference Guide 24 76.8600-50143G © 2015 Coriant Performance Counters 76.8600-50143G © 2015 Coriant BMP Counter Description Support ([8660,8630 CDC1 / CDC2 / IFC1 / IFC2 / ELC1] / 8620 / 8602 / 8605 / 8607 / 8609 / 8611 / 8615 / [8665 vCU / LU1 / SU1]) compressionRatio Parameter indicates the average compression ratio ACG has achieved using the following formula: (1 – ( (SignalingBackhaulBW + bearerBackhaulBW) / (SignalingAbisBW + bearerAbisBW) ) *100 In the case of ATM transport this reflects also the achieved compression on the ATM backhaul trunk In the case of ATM PWE3 transport overhead is not included The value parameter indicates can be translated in user interface to a percentage value with two decimal accuracy using the following formula: P = (X-100 000) / 100 % Percentage value can be positive or negative FP [- / - / 2.9A / 3.0 / -] / 2.9A / - / 1.1A / / - / - / - [- / - / -] trunkUtilization Parameter indicates the utilization of the bearer VCC using the following formula: ( - (compressedBearerBW / allocatedBearerBW) ) *100 Allocated bearer bandwidth is defined by the traffic parameters of the bearer VCC as following: CBR-> PCR, VBR -> SCR, UBR+ -> MCR , UBR -> PCR In the case of VBR the value can in be in some cases as high 3000% See compressionRatio parameter how the actual value is coded to the parameter Parameter is shown with decimals in user interface FP [- / - / 2.9A / 3.0 / -] / 2.9A / - / 1.1A / / - / - / - [- / - / -] highUtilizationSeconds Parameter indicates the number of seconds backhaul utilization has exceed the high utilization threshold FP [- / - / 2.9A / 3.0 / -] / 2.9A / - / 1.1A / / - / - / - [- / - / -] cfoIdleReceivedBits Parameter indicates the number of received Abis bits from TDM interface which are compressed and send to backhaul during the period Value is reported in terms of kbits (1k=1000) FP [- / - / 2.9A / 3.0 / -] / 2.9A / - / 1.1A / / - / - / - [- / - / -] cfoIdleDiscardedTransmitBits Parameter indicates the number of received Abis bits from TDM interface which are compressed but discarded due to the congestion on backhaul during the period Value is reported in terms of kbits (1k=1000) FP [- / - / 2.9A / 3.0 / -] / 2.9A / - / 1.1A / / - / - / - [- / - / -] cfoIdleDegradedSeconds Parameter indicates the number of CFO and Idle degraded seconds during the period FP [- / - / 2.9A / 3.0 / -] / 2.9A / - / 1.1A / / - / - / - [- / - / -] 8600 Smart Routers Performance Counters Reference Guide 25 Performance Counters 1.5 1.5.1 BMP Counter Description Support ([8660,8630 CDC1 / CDC2 / IFC1 / IFC2 / ELC1] / 8620 / 8602 / 8605 / 8607 / 8609 / 8611 / 8615 / [8665 vCU / LU1 / SU1]) jitterBufferOverFlows Parameter indicates the number of over flows occurred in jitter buffer FP [- / - / 2.9A / 3.0 / -] / 2.9A / - / 1.1A / / - / - / - [- / - / -] jitterBufferUnderFlows Parameter indicates the number of under flows occurred in jitter buffer FP [- / - / 2.9A / 3.0 / -] / 2.9A / - / 1.1A / / - / - / - [- / - / -] Interface SDH Counters Rs This resource is used to hold the 15 and 24h current data and history register counts for SDH Regenerator section or SONET Section layer GR-253/GR-820 PM primitives are supported in ANSI mode and G.826 PM primitives in ETSI mode CLI: show interface performance BMP Counter Description Support ([8660,8630 CDC1 / CDC2 / IFC1 / IFC2 / ELC1] / 8620 / 8602 / 8605 / 8607 / 8609 / 8611 / 8615 / [8665 vCU / LU1 / SU1]) neCv Near-end code violation count FP [- / - / 2.10 / 3.0 / -] / 2.10 / - / - / - / - / - / - [- / - / -] neEs Near-end errored seconds FP [- / - / 2.10 / 3.0 / -] / 2.10 / - / - / - / - / - / - [- / - / -] neSes Near-end severely errored seconds FP [- / - / 2.10 / 3.0 / -] / 2.10 / - / - / - / - / - / - [- / - / -] neSefs Near-end severely errored framing seconds This primitive is identical with out of framed seconds (OOFS) specified in G.783 FP [- / - / 2.10 / 3.0 / -] / 2.10 / - / - / - / - / - / - [- / - / -] neBbe (g826Primitives) Near-end errored blocks not occurring as part of an SES FP [- / - / 2.10 / 3.0 / -] / 2.10 / - / - / - / - / - / - [- / - / -] 8600 Smart Routers Performance Counters Reference Guide 26 76.8600-50143G © 2015 Coriant Performance Counters 1.5.2 Ms This resource is used to hold the 15 and 24h current data and history register counts for SDH Multiplex section or SONET Line layer GR-253/GR-820 PM primitives are supported in ANSI mode and G.826 PM primitives in ETSI mode CLI: show interface performance 76.8600-50143G © 2015 Coriant BMP Counter Description Support ([8660,8630 CDC1 / CDC2 / IFC1 / IFC2 / ELC1] / 8620 / 8602 / 8605 / 8607 / 8609 / 8611 / 8615 / [8665 vCU / LU1 / SU1]) neCv Near-end code violation count FP [- / - / 2.10 / 3.0 / -] / 2.10 / - / - / - / - / - / - [- / - / -] neEs Near-end errored seconds FP [- / - / 2.10 / 3.0 / -] / 2.10 / - / - / - / - / - / - [- / - / -] neSes Near-end severely errored seconds FP [- / - / 2.10 / 3.0 / -] / 2.10 / - / - / - / - / - / - [- / - / -] neUas Near-end unavailable seconds FP [- / - / 2.10 / 3.0 / -] / 2.10 / - / - / - / - / - / - [- / - / -] feCv Far-end code violation count FP [- / - / 2.10 / 3.0 / -] / 2.10 / - / - / - / - / - / - [- / - / -] feEs Far-end errored seconds FP [- / - / 2.10 / 3.0 / -] / 2.10 / - / - / - / - / - / - [- / - / -] feSes Far-end severely errored seconds FP [- / - / 2.10 / 3.0 / -] / 2.10 / - / - / - / - / - / - [- / - / -] feUas Far-end unavailable seconds FP [- / - / 2.10 / 3.0 / -] / 2.10 / - / - / - / - / - / - [- / - / -] psc MSP/APS protection switch count FP [- / - / 2.10 / 3.0 / -] / 2.10 / - / - / - / - / - / - [- / - / -] psd MSP/APS protection switch duration FP [- / - / 2.10 / 3.0 / -] / 2.10 / - / - / - / - / - / - [- / - / -] neFc (gr253Primitives) Near-end failure count FP [- / - / 2.10 / 3.0 / -] / 2.10 / - / - / - / - / - / - [- / - / -] 8600 Smart Routers Performance Counters Reference Guide 27 Performance Counters 1.5.3 BMP Counter Description Support ([8660,8630 CDC1 / CDC2 / IFC1 / IFC2 / ELC1] / 8620 / 8602 / 8605 / 8607 / 8609 / 8611 / 8615 / [8665 vCU / LU1 / SU1]) feFc (gr253Primitives) Far-end failure count FP [- / - / 2.10 / 3.0 / -] / 2.10 / - / - / - / - / - / - [- / - / -] neBbe (g826Primitives) Near-end errored blocks not occurring as part of an SES FP [- / - / 2.10 / 3.0 / -] / 2.10 / - / - / - / - / - / - [- / - / -] feBbe (g826Primitives) Far-end errored blocks not occurring as part of an SES FP [- / - / 2.10 / 3.0 / -] / 2.10 / - / - / - / - / - / - [- / - / -] Sts / Vt15 Path This resource is used to hold the 15 and 24h current data and history register counts for SDH VC-4/VC-12 or SONET STS path/VT1.5 layers GR-253/GR-820 PM primitives are supported in ANSI mode and G.826 PM primitives in ETSI mode CLI: show interface performance BMP Counter Description Support ([8660,8630 CDC1 / CDC2 / IFC1 / IFC2 / ELC1] / 8620 / 8602 / 8605 / 8607 / 8609 / 8611 / 8615 / [8665 vCU / LU1 / SU1]) neCv Near-end code violation count FP [- / - / 2.10 / 3.0 / -] / 2.10 / - / - / - / - / - / - [- / - / -] neEs Near-end errored seconds FP [- / - / 2.10 / 3.0 / -] / 2.10 / - / - / - / - / - / - [- / - / -] neSes Near-end severely errored seconds FP [- / - / 2.10 / 3.0 / -] / 2.10 / - / - / - / - / - / - [- / - / -] neUas Near-end unavailable seconds FP [- / - / 2.10 / 3.0 / -] / 2.10 / - / - / - / - / - / - [- / - / -] nePpjcDet Near-end positive pointer justification count detected in the receiver FP [- / - / 2.10 / 3.0 / -] / 2.10 / - / - / - / - / - / - [- / - / -] neNpjcDet Near-end negative pointer justification count detected in the receiver FP [- / - / 2.10 / 3.0 / -] / 2.10 / - / - / - / - / - / - [- / - / -] 8600 Smart Routers Performance Counters Reference Guide 28 76.8600-50143G © 2015 Coriant Performance Counters 1.6 1.6.1 BMP Counter Description Support ([8660,8630 CDC1 / CDC2 / IFC1 / IFC2 / ELC1] / 8620 / 8602 / 8605 / 8607 / 8609 / 8611 / 8615 / [8665 vCU / LU1 / SU1]) feCv Far-end code violation count FP [- / - / 2.10 / 3.0 / -] / 2.10 / - / - / - / - / - / - [- / - / -] feEs Far-end errored seconds FP [- / - / 2.10 / 3.0 / -] / 2.10 / - / - / - / - / - / - [- / - / -] feSes Far-end severely errored seconds FP [- / - / 2.10 / 3.0 / -] / 2.10 / - / - / - / - / - / - [- / - / -] feUas Far-end unavailable seconds FP [- / - / 2.10 / 3.0 / -] / 2.10 / - / - / - / - / - / - [- / - / -] neFc (gr253Primitives) Near-end failure count FP [- / - / 2.10 / 3.0 / -] / 2.10 / - / - / - / - / - / - [- / - / -] feFc (gr253Primitives) Far-end failure count FP [- / - / 2.10 / 3.0 / -] / 2.10 / - / - / - / - / - / - [- / - / -] neBbe (g826Primitives) Near-end errored blocks not occurring as part of an SES FP [- / - / 2.10 / 3.0 / -] / 2.10 / - / - / - / - / - / - [- / - / -] feBbe (g826Primitives) Far-end errored blocks not occurring as part of an SES FP [- / - / 2.10 / 3.0 / -] / 2.10 / - / - / - / - / - / - [- / - / -] Layer Tunneling Counters Pwe3 Circuit This resource is used to hold the 15 and 24h current data and history register counts for PWE3 circuit CLI: show pwe3 circuit performance 76.8600-50143G © 2015 Coriant 8600 Smart Routers Performance Counters Reference Guide 29 Performance Counters 1.7 1.7.1 BMP Counter Description Support ([8660,8630 CDC1 / CDC2 / IFC1 / IFC2 / ELC1] / 8620 / 8602 / 8605 / 8607 / 8609 / 8611 / 8615 / [8665 vCU / LU1 / SU1]) hcInPackets Count packets transmitted to PWE3 tunnel FP [2.11 / 4.1 / - / - / -] / 2.11 / 1.0 / 1.3 / 1.1 / 1.0 / 1.1 / - [- / - / -] hcInOctets Count octets transmitted to PWE3 tunnel FP [2.11 / 4.1 / - / - / -] / 2.11 / 1.0 / 1.3 / 1.1 / 1.0 / 1.1 / - [- / - / -] hcOutPackets Count packets received from PWE3 tunnel FP [2.11 / 4.1 / - / - / -] / 2.11 / 1.0 / 1.3 / 1.1 / 1.0 / 1.1 / - [- / - / -] hcOutOctets Count octets Received from PWE3 tunnel FP [2.11 / 4.1 / - / - / -] / 2.11 / 1.0 / 1.3 / 1.1 / 1.0 / 1.1 / - [- / - / -] pwMissingPackets Count number of missing PWE3 packets (as detected via control word sequence number gaps) FP [2.11 / 4.1 / - / - / -] / 2.11 / 1.0 / 1.3 / 1.1 / 1.0 / 1.1 / - [- / - / -] pwMisOrderDropped Number of packets detected out of order (via control word sequence numbers), and could not be re-ordered, or could not fit in the jitter buffer FP [2.11 / 4.1 / - / - / -] / 2.11 / 1.0 / 1.3 / 1.1 / 1.0 / 1.1 / - [- / - / -] Node Testing and Measurement Counters Power Consumption This resource represents power consumption measure for unit CDC1: Requires PIM module CLI: show environment 8600 Smart Routers Performance Counters Reference Guide 30 76.8600-50143G © 2015 Coriant Performance Counters 1.7.2 BMP Counter Description Support ([8660,8630 CDC1 / CDC2 / IFC1 / IFC2 / ELC1] / 8620 / 8602 / 8605 / 8607 / 8609 / 8611 / 8615 / [8665 vCU / LU1 / SU1]) current Current power consumption FP [- / 4.1 / - / 3.1 / 4.0] / - / - / - / - / - / / 7.0 [7.0 / 7.0 / 7.0] max Maximum power consumption since last reset FP [- / 4.1 / - / 3.1 / 4.0] / - / - / - / - / - / / 7.0 [7.0 / 7.0 / 7.0] Minimum power consumption since last reset (during normal operation) FP [- / 4.1 / - / 3.1 / 4.0] / - / - / - / - / - / / 7.0 [7.0 / 7.0 / 7.0] average Average power consumption since last reset FP [- / 4.1 / - / 3.1 / 4.0] / - / - / - / - / - / / 7.0 [7.0 / 7.0 / 7.0] CPU / Cache / Memory This resource represents unit's internal HW resource usage CLI: show cpu load 76.8600-50143G © 2015 Coriant BMP Counter Description Support ([8660,8630 CDC1 / CDC2 / IFC1 / IFC2 / ELC1] / 8620 / 8602 / 8605 / 8607 / 8609 / 8611 / 8615 / [8665 vCU / LU1 / SU1]) loadMax Max CPU load during this interval as percent of time the CPU is running non-background tasks FP [3.1 / 4.1 / 3.1 / 3.1 / 4.0] / 3.1 / 1.0 / 1.4 / 1.1 / 1.0 / 1.1 / 1.0 [- / 7.0 / 7.0] loadAverage Average CPU load during this interval as percent of time the CPU is running non-background tasks FP [3.1 / 4.1 / 3.1 / 3.1 / 4.0] / 3.1 / 1.0 / 1.4 / 1.1 / 1.0 / 1.1 / 1.0 [- / 7.0 / 7.0] l1CacheHitRatio L1 cache hit ratio during this interval If the device does not support L1 cache reporting this parameter is set to NoValue FP [3.1 / 4.1 / 3.1 / 3.1 / 4.0] / 3.1 / 1.0 / 1.4 / 1.1 / 1.0 / 1.1 / 1.0 [- / 7.0 / 7.0] 8600 Smart Routers Performance Counters Reference Guide 31 Performance Counters 1.7.3 BMP Counter Description Support ([8660,8630 CDC1 / CDC2 / IFC1 / IFC2 / ELC1] / 8620 / 8602 / 8605 / 8607 / 8609 / 8611 / 8615 / [8665 vCU / LU1 / SU1]) l2CacheHitRatio L2 cache hit ratio during this interval If the device does not support L2 cache reporting this parameter is set to NoValue FP [3.1 / 4.1 / 3.1 / 3.1 / 4.0] / 3.1 / 1.0 / 1.4 / 1.1 / 1.0 / 1.1 / 1.0 [- / 7.0 / 7.0] memoryUsage RAM memory usage FP [3.1 / 4.1 / 3.1 / 3.1 / 4.0] / 3.1 / 1.0 / 1.4 / 1.1 / 1.0 / 1.1 / 1.0 [- / 7.0 / 7.0] NPU This resource represents internal NPU usage 86x0: Supported modules: 4xSTM-1/OC-3 ATM, 1xchSTM-1/chOC-3 MS, 4xchSTM-1/chOC-3 MS, 24xchE1/chT1 MS CLI: show npu load BMP Counter Description Support ([8660,8630 CDC1 / CDC2 / IFC1 / IFC2 / ELC1] / 8620 / 8602 / 8605 / 8607 / 8609 / 8611 / 8615 / [8665 vCU / LU1 / SU1]) loadAverage (npuCore) Average load FP [- / - / - / - / -] / - / 1.0 / 1.4 / 1.1 / 1.0 / 1.1 / - [- / - / -] loadMaximum (npuCore) Maximum load FP [- / - / - / - / -] / - / 1.0 / 1.4 / 1.1 / 1.0 / 1.1 / - [- / - / -] range0to10 (npuCore) Number of sub-period samples in this load percentage range FP [- / - / - / - / -] / - / 1.0 / 1.4 / 1.1 / 1.0 / 1.1 / - [- / - / -] range10to20 (npuCore) Number of sub-period samples in this load percentage range FP [- / - / - / - / -] / - / 1.0 / 1.4 / 1.1 / 1.0 / 1.1 / - [- / - / -] range20to30 (npuCore) Number of sub-period samples in this load percentage range FP [- / - / - / - / -] / - / 1.0 / 1.4 / 1.1 / 1.0 / 1.1 / - [- / - / -] range30to40 (npuCore) Number of sub-period samples in this load percentage range FP [- / - / - / - / -] / - / 1.0 / 1.4 / 1.1 / 1.0 / 1.1 / - [- / - / -] 8600 Smart Routers Performance Counters Reference Guide 32 76.8600-50143G © 2015 Coriant Performance Counters 76.8600-50143G © 2015 Coriant BMP Counter Description Support ([8660,8630 CDC1 / CDC2 / IFC1 / IFC2 / ELC1] / 8620 / 8602 / 8605 / 8607 / 8609 / 8611 / 8615 / [8665 vCU / LU1 / SU1]) range40to50 (npuCore) Number of sub-period samples in this load percentage range FP [- / - / - / - / -] / - / 1.0 / 1.4 / 1.1 / 1.0 / 1.1 / - [- / - / -] range50to60 (npuCore) Number of sub-period samples in this load percentage range FP [- / - / - / - / -] / - / 1.0 / 1.4 / 1.1 / 1.0 / 1.1 / - [- / - / -] range60to70 (npuCore) Number of sub-period samples in this load percentage range FP [- / - / - / - / -] / - / 1.0 / 1.4 / 1.1 / 1.0 / 1.1 / - [- / - / -] range70to80 (npuCore) Number of sub-period samples in this load percentage range FP [- / - / - / - / -] / - / 1.0 / 1.4 / 1.1 / 1.0 / 1.1 / - [- / - / -] range80to90 (npuCore) Number of sub-period samples in this load percentage range FP [- / - / - / - / -] / - / 1.0 / 1.4 / 1.1 / 1.0 / 1.1 / - [- / - / -] range90to100 (npuCore) Number of sub-period samples in this load percentage range FP [- / - / - / - / -] / - / 1.0 / 1.4 / 1.1 / 1.0 / 1.1 / - [- / - / -] loadAverage (queueMemory) Average load FP [- / - / - / - / -] / - / 1.0 / 1.4 / 1.1 / 1.0 / 1.1 / - [- / - / -] loadMaximum (queueMemory) Maximum load FP [- / - / - / - / -] / - / 1.0 / 1.4 / 1.1 / 1.0 / 1.1 / - [- / - / -] range0to10 (queueMemory) Number of sub-period samples in this load percentage range FP [- / - / - / - / -] / - / 1.0 / 1.4 / 1.1 / 1.0 / 1.1 / - [- / - / -] range10to20 (queueMemory) Number of sub-period samples in this load percentage range FP [- / - / - / - / -] / - / 1.0 / 1.4 / 1.1 / 1.0 / 1.1 / - [- / - / -] range20to30 (queueMemory) Number of sub-period samples in this load percentage range FP [- / - / - / - / -] / - / 1.0 / 1.4 / 1.1 / 1.0 / 1.1 / - [- / - / -] range30to40 (queueMemory) Number of sub-period samples in this load percentage range FP [- / - / - / - / -] / - / 1.0 / 1.4 / 1.1 / 1.0 / 1.1 / - [- / - / -] range40to50 (queueMemory) Number of sub-period samples in this load percentage range FP [- / - / - / - / -] / - / 1.0 / 1.4 / 1.1 / 1.0 / 1.1 / - [- / - / -] range50to60 (queueMemory) Number of sub-period samples in this load percentage range FP [- / - / - / - / -] / - / 1.0 / 1.4 / 1.1 / 1.0 / 1.1 / - [- / - / -] 8600 Smart Routers Performance Counters Reference Guide 33 Performance Counters BMP Counter Description Support ([8660,8630 CDC1 / CDC2 / IFC1 / IFC2 / ELC1] / 8620 / 8602 / 8605 / 8607 / 8609 / 8611 / 8615 / [8665 vCU / LU1 / SU1]) range60to70 (queueMemory) Number of sub-period samples in this load percentage range FP [- / - / - / - / -] / - / 1.0 / 1.4 / 1.1 / 1.0 / 1.1 / - [- / - / -] range70to80 (queueMemory) Number of sub-period samples in this load percentage range FP [- / - / - / - / -] / - / 1.0 / 1.4 / 1.1 / 1.0 / 1.1 / - [- / - / -] range80to90 (queueMemory) Number of sub-period samples in this load percentage range FP [- / - / - / - / -] / - / 1.0 / 1.4 / 1.1 / 1.0 / 1.1 / - [- / - / -] range90to100 (queueMemory) Number of sub-period samples in this load percentage range FP [- / - / - / - / -] / - / 1.0 / 1.4 / 1.1 / 1.0 / 1.1 / - [- / - / -] loadAverage (memoryBus) Average load FP [- / - / - / - / -] / - / 1.0 / 1.4 / 1.1 / 1.0 / 1.1 / - [- / - / -] loadMaximum (memoryBus) Maximum load FP [- / - / - / - / -] / - / 1.0 / 1.4 / 1.1 / 1.0 / 1.1 / - [- / - / -] range0to10 (memoryBus) Number of sub-period samples in this load percentage range FP [- / - / - / - / -] / - / 1.0 / 1.4 / 1.1 / 1.0 / 1.1 / - [- / - / -] range10to20 (memoryBus) Number of sub-period samples in this load percentage range FP [- / - / - / - / -] / - / 1.0 / 1.4 / 1.1 / 1.0 / 1.1 / - [- / - / -] range20to30 (memoryBus) Number of sub-period samples in this load percentage range FP [- / - / - / - / -] / - / 1.0 / 1.4 / 1.1 / 1.0 / 1.1 / - [- / - / -] range30to40 (memoryBus) Number of sub-period samples in this load percentage range FP [- / - / - / - / -] / - / 1.0 / 1.4 / 1.1 / 1.0 / 1.1 / - [- / - / -] range40to50 (memoryBus) Number of sub-period samples in this load percentage range FP [- / - / - / - / -] / - / 1.0 / 1.4 / 1.1 / 1.0 / 1.1 / - [- / - / -] range50to60 (memoryBus) Number of sub-period samples in this load percentage range FP [- / - / - / - / -] / - / 1.0 / 1.4 / 1.1 / 1.0 / 1.1 / - [- / - / -] range60to70 (memoryBus) Number of sub-period samples in this load percentage range FP [- / - / - / - / -] / - / 1.0 / 1.4 / 1.1 / 1.0 / 1.1 / - [- / - / -] range70to80 (memoryBus) Number of sub-period samples in this load percentage range FP [- / - / - / - / -] / - / 1.0 / 1.4 / 1.1 / 1.0 / 1.1 / - [- / - / -] 8600 Smart Routers Performance Counters Reference Guide 34 76.8600-50143G © 2015 Coriant Performance Counters 76.8600-50143G © 2015 Coriant BMP Counter Description Support ([8660,8630 CDC1 / CDC2 / IFC1 / IFC2 / ELC1] / 8620 / 8602 / 8605 / 8607 / 8609 / 8611 / 8615 / [8665 vCU / LU1 / SU1]) range80to90 (memoryBus) Number of sub-period samples in this load percentage range FP [- / - / - / - / -] / - / 1.0 / 1.4 / 1.1 / 1.0 / 1.1 / - [- / - / -] range90to100 (memoryBus) Number of sub-period samples in this load percentage range FP [- / - / - / - / -] / - / 1.0 / 1.4 / 1.1 / 1.0 / 1.1 / - [- / - / -] 8600 Smart Routers Performance Counters Reference Guide 35 ... and/or other countries 76. 8600- 50143G © 2015 Coriant 8600 Smart Routers Performance Counters Reference Guide 8600 Smart Routers Performance Counters Reference Guide 76. 8600- 50143G © 2015 Coriant... CLI 8600 Smart Routers Performance Counters Reference Guide (76. 8600- 50143) Provides an overview of 8600 system supported performance counters 8600 Smart Routers Performance Counters Reference Guide. .. fi-documentation@tellabs.com 8600 Smart Routers Performance Counters Reference Guide 12 76. 8600- 50143G © 2015 Coriant 8600 Smart Routers Discontinued Products 8600 Smart Routers Discontinued Products 8600 Smart Routers