SERVICE HANDBOOK MULTIFUNCTIONAL DIGITAL SYSTEMS e-STUDIO520/600/720/850 e-STUDIO523/603/723/853 Model: DP-5200/6000/7200/8500 Publish Date: March 2005 File No SHE040005I0 R04102168901-TTEC Ver09_2007-11 Trademarks • • • • • • • • • • • The official name of Windows 95 is Microsoft Windows 95 Operating System The official name of Windows 98 is Microsoft Windows 98 Operating System The official name of Windows Me is Microsoft Windows Millennium Edition Operating System The official name of Windows 2000 is Microsoft Windows 2000 Operating System The official name of Windows XP is Microsoft Windows XP Operating System Microsoft, Windows, Windows NT and the brand names and product names of other Microsoft products are trademarks or registered trademarks of Microsoft Corporation in the U.S and/or other countries Apple, AppleTalk, Macintosh, and Mac are trademarks of Apple Computer, Inc in the U.S and other countries PostScript is a trademark of Adobe Systems Incorporated NOVELL, NetWare, and NDS are trademarks or registered trademarks of Novell, Inc Molykote is a registered trademark of Dow Corning Corporation Other company names and product names in this manual are the trademarks of their respective companies © 2005 - 2007 TOSHIBA TEC CORPORATION All rights reserved Under the copyright laws, this manual cannot be reproduced in any form without prior written permission of TOSHIBA TEC CORPORATION No patent liability is assumed, however, with respect to the use of the information contained herein GENERAL PRECAUTIONS REGARDING THE SERVICE FOR e-STUDIO520/523/600/603/720/723/850/853 The installation and service should be done by a qualified service technician 1) Transportation/Installation - When transporting/installing the equipment, employ four persons and be sure to move it by the casters while lifting the stoppers The equipment is quite heavy and weighs approximately 210 kg (463 lb), therefore pay full attention when handling it - Be sure not to hold the movable parts or units (e.g the RADF) when transporting the equipment - Be sure to use a dedicated outlet with AC 115 V / 16 A, 127 V / 16 A, 220 V or 220-240 V / A for its power source - The equipment must be grounded for safety - Select a suitable place for installation Avoid excessive heat, high humidity, dust, vibration and direct sunlight - Provide proper ventilation since the equipment emits a slight amount of ozone - To insure adequate working space for the copying operation, keep a minimum clearance of 80 cm (32”) on the left, 80 cm (32”) on the right and 10 cm (4”) on the rear - The equipment shall be installed near the socket outlet and shall be accessible - Be sure to fix and plug in the power cable securely after the installation so that no one trips over it 07/11 2) General Precautions at Service - Be sure to turn the power OFF and unplug the power cable during service (except for the service should be done with the power turned ON) - Unplug the power cable and clean the area around the prongs of the plug and socket outlet once a year or more A fire may occur when dust lies on this area - When the parts are disassembled, reassembly is the reverse of disassembly unless otherwise noted in this manual or other related documents Be careful not to install small parts such as screws, washers, pins, E-rings, star washers in the wrong places - Basically, the equipment should not be operated with any parts removed or disassembled - The PC board must be stored in an anti-electrostatic bag and handled carefully using a wristband since the ICs on it may be damaged due to static electricity Caution: Before using the wristband, unplug the power cable of the equipment and make sure that there are no charged objects which are not insulated in the vicinity - - - Avoid expose to laser beam during service This equipment uses a laser diode Be sure not to expose your eyes to the laser beam Do not insert reflecting parts or tools such as a screwdriver on the laser beam path Remove all reflecting metals such as watches, rings, etc before starting service Be sure not to touch high-temperature sections such as the exposure lamp, fuser unit, damp heater and areas around them Be sure not to touch high-voltage sections such as the chargers, transfer belt, IH control circuit, developer, high-voltage transformer, exposure lamp control inverter, inverter for the LCD backlight and power supply unit Especially, the board of these components should not be touched since the electric charge may remain in the capacitors, etc on them even after the power is turned OFF Make sure that the equipment will not operate before touching potentially dangerous places (e.g rotating/operating sections such as gears, belts pulleys, fans and laser beam exit of the laser optical unit) Be careful when removing the covers since there might be the parts with very sharp edges underneath When servicing the equipment with the power turned ON, be sure not to touch live sections and rotating/operating sections Avoid exposing your eyes to laser beam Use designated jigs and tools Use recommended measuring instruments or equivalents Return the equipment to the original state and check the operation when the service is finished Be very careful to treat the touch panel gently and never hit it Breaking the surface could cause malfunctions 3) Important Service Parts for Safety - The breaker, door switch, fuse, thermostat, thermofuse, thermistor, batteries, IC-RAMs including lithium batteries, etc are particularly important for safety Be sure to handle/install them properly If these parts are short-circuited and their functions become ineffective, they may result in fatal accidents such as burnout Do not allow a short-circuit or not use the parts not recommended by Toshiba TEC Corporation 4) Cautionary Labels - During servicing, be sure to check the rating plate and cautionary labels such as “Unplug the power cable during service”, “CAUTION HOT”, “CAUTION HIGH VOLTAGE”, “CAUTION LASER BEAM”, etc to see if there is any dirt on their surface and if they are properly stuck to the equipment 06/09 5) Disposal of the Equipment, Supplies, Packing Materials, Used Batteries and IC-RAMs - Regarding the recovery and disposal of the equipment, supplies, packing materials, used batteries and IC-RAMs including lithium batteries, follow the relevant local regulations or rules Caution: Dispose of used batteries and IC-RAMs including lithium batteries according to this manual Attention: Se débarrasser de batteries et IC-RAMs usés y compris les batteries en lithium selon ce manuel Vorsicht: Entsorgung des gebrauchten Batterien und IC-RAMs (inclusive der Lithium-Batterie) nach diesem Handbuch CONTENTS e-STUDIO520/600/720/850 SPECIFICATIONS/ACCESSORIES/OPTIONS/SUPPLIES 1-1 1.1 1.2 1.3 1.4 1.5 Specifications 1-1 Accessories 1-10 Options 1-11 Supplies 1-12 System List 1-13 ERROR CODE AND SELF-DIAGNOSTIC MODE 2-1 2.1 Error Code List 2-1 2.1.1 Jam 2-1 2.1.2 Service call 2-9 2.1.3 Error in Internet FAX / Scanning Function 2-15 2.1.4 Printer function error 2-25 2.2 Self-diagnosis Modes 2-27 2.2.1 Input check (Test mode 03) 2-29 2.2.2 Output check (test mode 03) 2-36 2.2.3 Test print mode (test mode 04) 2-40 2.2.4 Adjustment mode (05) 2-41 2.2.5 Setting mode (08) 2-74 2.2.6 Pixel counter 2-190 2.2.7 Classification List of Adjustment Mode (05) / Setting Mode (08) 2-200 ADJUSTMENT 3-1 3.1 Adjustment of Auto-Toner Sensor 3-1 3.2 Image Dimensional Adjustment 3-3 3.2.1 General description 3-3 3.2.2 Paper alignment at the registration roller 3-5 3.2.3 Printer related adjustment 3-9 3.2.4 Scanner related adjustment 3-14 3.3 Image Quality Adjustment (Copying Function) 3-23 3.3.1 Density adjustment 3-23 3.3.2 Gamma slope adjustment 3-24 3.3.3 Background adjustment 3-24 3.3.4 Sharpness adjustment 3-24 3.3.5 Setting range correction 3-25 3.3.6 Setting range correction (Adjustment of background peak) 3-25 3.3.7 Adjustment of smudged/faint text 3-26 3.4 Image Quality Adjustment (Printing Function) 3-27 3.4.1 Adjustment of smudged/faint text 3-27 3.4.2 Gamma balance adjustment 3-27 3.4.3 Image density adjustment 3-28 3.5 Image Quality Adjustment (Scanning Function) 3-29 3.5.1 Density adjustment 3-29 3.5.2 Sharpness adjustment 3-30 3.5.3 Setting range correction 3-31 3.5.4 Setting range correction (Adjustment of background peak) 3-31 3.5.5 Background adjustment 3-32 3.6 Measurement at Replacement of High-Voltage Transformer 3-33 3.6.1 Measurement 3-33 3.7 Adjustment of the Scanner Section 3-37 3.7.1 Carriages 3-37 3.7.2 Lens unit 3-41 3.7.3 Scan motor 3-44 © 2005 - 2007 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO520/523/600/603/720/723/850/853 CONTENTS 05/05 3.8 Adjustment of the Paper Feeding System 3-45 3.8.1 Sheet sideways deviation caused by paper feeding 3-45 3.8.2 Separation roller pressure force adjustment 3-47 3.9 Adjustment of Developer Unit 3-49 3.10 Adjustment of Fuser Unit 3-50 3.10.1 Adjustment of fuser roller pressure 3-50 3.10.2 Setting of fuser/pressure roller temperature 3-52 3.10.3 Adjustment of fuser entrance guide 3-53 3.10.4 High-fusing mode 3-54 3.10.5 Changing Printing Speed 3-55 3.11 Adjustment of the RADF 3-56 3.11.1 Adjustment of RADF position 3-56 3.11.2 Adjustment of RADF height 3-60 3.11.3 Skew adjustment 3-61 3.11.4 Automatic adjustment of sensors and initialization of EEPROM 3-63 3.11.5 Adjustment of reverse solenoid 3-64 3.11.6 Adjustment of RADF opening/closing switch 3-66 3.11.7 Adjustment of original tray width 3-67 3.12 Adjustment of Finisher 3-68 3.12.1 Adjusting the Height Sensor (PS1) 3-68 3.12.2 Adjusting the Alignment Position 3-69 3.12.3 Adjusting the Staple Position (stapler movement range) 3-70 3.12.4 Adjusting the Buffer Roller Winding Amount 3-72 3.13 Adjustment of Saddle stitch finisher 3-75 3.13.1 Adjusting the Folding Position 3-75 3.13.2 Stitching Position (adjusting center stitching) 3-78 3.14 Adjustment of Hole punch unit 3-79 3.14.1 Sensor output adjustment 3-79 3.14.2 Registering the number of punch holes 3-80 3.14.3 Checking the sensitivity level of the transmission sensor 3-81 3.15 Adjustment of Inserter 3-82 3.15.1 Tray guide width adjustment 3-82 3.15.2 Input check 3-83 3.15.3 Check of sensor operations 3-85 3.15.4 Check of sensor operations 3-86 3.16 Adjustment of LCF (MP-4004) 3-87 3.16.1 Sheet sideways deviation adjustment 3-87 3.16.2 LCF slant adjustment 3-89 PREVENTIVE MAINTENANCE (PM) 4-1 4.1 PM Support Mode 4-1 4.1.1 General description 4-1 4.1.2 Operational flow and operational screen 4-1 4.1.3 Work flow of parts replacement 4-7 4.2 General Descriptions for PM Procedure 4-8 4.3 Operational Items in Overhauling 4-9 4.4 Preventive Maintenance Checklist 4-10 4.5 PM KIT 4-33 4.6 Jig List 4-34 4.7 Grease List 4-36 4.8 Precautions for Storing and Handling Supplies 4-37 4.8.1 Precautions for storing TOSHIBA supplies 4-37 4.8.2 Checking and cleaning of photoconductive drum 4-37 4.8.3 Checking and cleaning of drum cleaning blade and transfer belt cleaning blade 4-38 4.8.4 Handling of drum cleaning brush and transfer belt cleaning brush 4-38 4.8.5 Handling of transfer belt 4-38 e-STUDIO520/523/600/603/720/723/850/853 CONTENTS © 2005 - 2007 TOSHIBA TEC CORPORATION All rights reserved 05/05 4.8.6 Checking and cleaning of fuser roller and pressure roller 4-39 4.8.7 Checking and replacing of cleaning web 4-40 TROUBLESHOOTING 5-1 5.1 Diagnosis and Prescription for Each Error Code 5-1 5.1.1 Paper transport jam 5-1 5.1.2 Paper misfeeding 5-25 5.1.3 Cover open jam 5-33 5.1.4 Transport jam (RADF) 5-36 5.1.5 Finisher jam 5-42 5.1.6 Paper feeding system related service call 5-56 5.1.7 Scanning system related service call 5-60 5.1.8 Fuser unit related service call 5-62 5.1.9 Communication related service call 5-66 5.1.10 RADF related service call 5-68 5.1.11 Laser optical unit related service call 5-71 5.1.12 Finisher related service call 5-75 5.1.13 Service call for others 5-96 5.1.14 Error in Internet FAX / Scanning Function 5-101 5.1.15 Troubleshooting for image quality control 5-119 5.1.16 Troubleshooting for surface potential control 5-124 5.1.17 Troubleshooting for remaining toner detection sensor 5-126 5.2 Troubleshooting for the Image 5-127 5.3 Replacement of PC Boards and HDD 5-153 5.3.1 Replacing HDD 5-153 5.3.2 Replacing SYS board 5-156 5.3.3 Cautions when Data overwrite kit (GP-1060) is installed 5-157 5.3.4 Replacing NVRAM 5-158 5.3.5 HDD information display 5-159 5.4 Other errors 5-161 FIRMWARE UPDATING 6-1 6.1 Firmware Updating with Download Jig 6-3 6.1.1 PWA-DWNLD-350-JIG2 (48 MB) 6-5 6.1.2 PWA-DWNLD-350-JIG2 (48 MB) 6-11 6.1.3 Writing the data to the download jig (PWA-DWNLD-350-JIG) 6-26 6.1.4 K-PWA-DLM-320 6-28 6.2 Firmware Updating with USB Storage Device 6-39 POWER SUPPLY UNIT 7-1 7.1 Output Channel 7-1 7.2 Fuse 7-3 7.3 Configuration of Power Supply Unit 7-5 REMOTE SERVICE 8-1 8.1 Auto Supply Order 8-1 8.1.1 Outline 8-1 8.1.2 Setting Item 8-2 8.1.3 Setting procedure 8-5 8.1.4 Order Sheet Format 8-13 8.2 Service Notification 8-15 8.2.1 Outline 8-15 8.2.2 Setting 8-15 8.2.3 Items to be notified 8-21 © 2005 - 2007 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO520/523/600/603/720/723/850/853 CONTENTS 05/06 DATA CLONING with USB STORAGE DEVICE 9-1 10 WIRE HARNESS CONNECTION DIAGRAMS 10-1 10.1 AC Wire Harness 10-1 10.2 DC Wire Harness Appendix 10.3 Electric Parts Layout Appendix e-STUDIO520/523/600/603/720/723/850/853 CONTENTS © 2005 - 2007 TOSHIBA TEC CORPORATION All rights reserved 05/11 (6) Select the items to be restored with the digital keys The mark "*" is shown on the selected item The mark "*" can be deleted or added each time the corresponding digital key is pressed • To restore the data in a batch, select "4", "5" or "6" (Selecting "4" performs "1", "2" and "3" together.) • To restore the data individually, select the following items Be sure to select the same item as the one backed up individually Select "1: Address Book" only Select "2: Mail Box" only < Restoring Template> Select "3: Template" only Select "4: Combined" only Select "5: Department Code" only Select "6: User Info" only E.g.: In case of restoring the department management and user management information Fig 9-22 e-STUDIO520/523/600/603/720/723/850/853 DATA CLONING with USB STORAGE DEVICE © 2005 - 2007 TOSHIBA TEC CORPORATION All rights reserved - 16 05/11 (The following screens are given as an example of when all items are restored.) (7) Press the [Start] button The restore starts and the restoring status is displayed on the LCD screen Fig 9-23 (8) "Restore Completed" is displayed on the LCD screen when the restore has been properly completed Fig 9-24 (9) Turn the power OFF and remove the USB storage device (10) Clear the counter (in case of restoring "Department Code" and "User Info") Since the counter values are also copied, clear all of them However, the total counter is not copied Press the buttons as follows: [USER FUNCTION] → [ADMIN] → Enter the password → [COUNTER] → [DEPARTMENT SETTING] → Enter the password → [RESET ALL COUNTERS] * Enable the department management when the [RESET ALL COUNTERS] button is set to be disabled © 2005 - 2007 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO520/523/600/603/720/723/850/853 DATA CLONING with USB STORAGE DEVICE - 17 05/11 (11) Connect the USB storage device to the USB connector (host) on the SYS board (12) Turn the power ON while pressing the [5] and [9] button simultaneously The screen to select the backup/restore items is displayed Fig 9-25 Notes: • After the item is selected with the digital keys, displaying the next menu may take a long time • When “Disable” is set for the [Data Cloning Function] in TopAccess, the following screen is displayed Contact and ask the administrator to change the setting on TopAccess Fig 9-26 (13) Press the [4] button The screen to select the setting restore item is displayed In this screen, the items to be restored are shown after the mark "*" (No items are selected in the screen by default.) Fig 9-27 e-STUDIO520/523/600/603/720/723/850/853 DATA CLONING with USB STORAGE DEVICE © 2005 - 2007 TOSHIBA TEC CORPORATION All rights reserved - 18 07/11 (14) Select the items to be restored with the digital keys The mark "*" is shown on the selected item The mark "*" can be deleted or added each time the corresponding digital key is pressed • To restore the data individually, select the following items Select "1: Network/Print Service" only Select "2: SaveAsFile/Email/InternetFAX" only Select "3: Notification" only Select "4: Directory Service" only Select "5: FAX Kit" only Select "6: WirelessLAN/Bluetooth Kit" only Note: Be sure to restore the same option items in the same condition as when the option items were backed up (The following screens are given as an example of when all TopAccess items are restored.) (15) Press the [Start] button The restore starts and the restoring status is displayed on the LCD screen Fig 9-28 © 2005 - 2007 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO520/523/600/603/720/723/850/853 DATA CLONING with USB STORAGE DEVICE - 19 05/11 (16) "Restore Completed" is displayed on the LCD screen when the restore has been properly completed Fig 9-29 (17) Turn the power OFF and remove the USB storage device e-STUDIO520/523/600/603/720/723/850/853 DATA CLONING with USB STORAGE DEVICE © 2005 - 2007 TOSHIBA TEC CORPORATION All rights reserved - 20 05/11 (18) Connect the USB storage device to the USB connector (host) on the SYS board (19) Turn the power ON while pressing the [5] and [9] button simultaneously The screen to select the backup/restore items is displayed Fig 9-30 Notes: • After the item is selected with the digital keys, displaying the next menu may take a long time • When “Disable” is set for the [Data Cloning Function] in TopAccess, the following screen is displayed Contact and ask the administrator to change the setting on TopAccess Fig 9-31 (20) Press the [6] button The screen to select the SRAM data restore item is displayed In this screen, the item to be restored is shown after the mark "*" (The item is not selected in the screen by default.) Fig 9-32 © 2005 - 2007 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO520/523/600/603/720/723/850/853 DATA CLONING with USB STORAGE DEVICE - 21 07/11 (21) Select the item to be restored with the digital keys The mark "*" is shown on the selected item The mark "*" can be deleted or added each time the corresponding digital key is pressed • To restore the data individually, select the following item Select "1 SRAM" Note: The backup/restore of the SRAM data can be performed only for the same model The ROM version must be the same when the data are backed up and restored (The following screens are given as an example of when SRAM data are restored.) (22) Press the [Start] button The restore starts and the restoring status is displayed on the LCD screen Fig 9-33 (23) "Restore Completed" is displayed on the LCD screen when the restore has been properly completed Fig 9-34 (24) Turn the power OFF and remove the USB storage device e-STUDIO520/523/600/603/720/723/850/853 DATA CLONING with USB STORAGE DEVICE © 2005 - 2007 TOSHIBA TEC CORPORATION All rights reserved - 22 05/11 [C] Confirmation of the error "Back Up ERROR X" (X: Error number) is displayed at the top of the LCD screen when the data have not been properly backed up / restored In this case, turn the power OFF and then check the following items After confirming and solving the problem, back up / restore the data again from the beginning • Does the USB storage device meet the conditions being used for this cloning? • Is the updated program file written on the USB storage device properly? • Is the USB storage device installed properly? • Is the USB storage device or the equipment damaged? Fig 9-35 Error number ERROR ERROR ERROR ERROR ERROR ERROR ERROR ERROR ERROR ERROR 10 ERROR 11 Error content Copy error I/F error USB memory full error Working folder error File not found error Security error Checksum error Model check error Version check error Destination check error Serial number check error © 2005 - 2007 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO520/523/600/603/720/723/850/853 DATA CLONING with USB STORAGE DEVICE - 23 05/11 [D] Backup file Backed up data files are encrypted The folder "user_data" is created in the root directory and the following files are stored in it Data item Address book Mailbox Template Back up the Address book, Mailbox and Template in a batch Department management information User management information File name BACKUP_ADDR.sct BACKUP_MBOX.sct BACKUP_TEMP.sct BACKUP_ALL.sct BACKUP_Department.sct BACKUP_User.sct The folder "setting_data" is created in the root directory and the following files are stored in it Data item Network / Print service SaveAsFile / Email / InternetFAX Notification setting Directory Service FAX setting Wireless LAN setting / Bluetooth setting File name network.sct scan.sct notice.sct ldap.sct fax.sct wl.sct, bl.sct The folder "sram_data" is created in the root directory and the following file is stored in it Data item File name SRAM * sram.sct In addition to the backed up data, the following files are created in each folder Back up item File name user_data.txt setting_data.txt sram_data.txt User data Setting item data SRAM data Version: VTD08.100 J Serial Number: 0123456789 Date: MON SEP 26 18:34:40 2005 • File format (user_data.txt, setting_data.txt, sram_data.txt: all in common) Line 1: Version Line 2: Serial number Line 3: Date e-STUDIO520/523/600/603/720/723/850/853 DATA CLONING with USB STORAGE DEVICE © 2005 - 2007 TOSHIBA TEC CORPORATION All rights reserved - 24 FG N G L LIVE Black NEUTRAL Breaker 10A White Black Noise Filter Black White Breaker 20A White Black Noise Filter White Black FIL board CN440 Black White J657 2 J657 1 Brown Blue 2 Blue White Brown Black Brown Blue Brown Blue © 2005 - 2007 TOSHIBA TEC CORPORATION All rights reserved 10 - 06/09 J I J654 Blue L K Brown Fuser detection switch J523 Black White J654 White Black Black White D C Black White Brown Blue J611 2 1 3 J655 Blue Black Brown J638 White 1 Black 2 Brown Blue White C F1 F2 S CN454 IH coil control circuit CN453 Center IH coil G White Black Dram damp heater thermostat Black White Scanner damp heater thermostat FUS board White Black Black Dram damp heater J34 J28 DH-SCN-N 1 DH-SCN-L 2 Scanner damp heater CN451 J608 N Side IH coil J840 1 2 J839 2 1 Dram damp heater (Front) Dram damp heater (Rear) Scanner damp heater (Right) 1 2 J32 Scanner damp heater (Left) 1 2 J31 DC DC Fuser roller side thermostat IH board White Switching regulator (Cover switch line) Switching regulator (Main switch line) Fuser roller center thermostat Finisher (Option) MJ-1029 only Switching regulator J658 CN401 CN452 CN607 CN450 L Side IH coil Fuser roller Fuser Brown Blue Black White White Black ASD/ASU/ARD/AUD/DAU/CND/KRD/TWD model: Standard, TNA/NAD/MJD/DMJ model: Option Black White J637 DH-DRM-N 3 2 DH-DRM-L 1 J33 1 2 1 White Black Blue White Brown Black J645 4 G E H F Main switch Cover interlock switch 4 J521 1 J652 Black White Brown Blue FG N NEUTRAL G L LIVE Black CN441 TNA/NAD/SAD model of all equipment, TWD model of e-STUDIO600/720 Inlet (AC IN) ASD/ASU/ARD/AUD/DAU/MJD/DMJ/CND/KRD model of all equipment, TWD model of e-STUDIO850 10 WIRE HARNESS CONNECTION DIAGRAMS 10.1 AC Wire Harness White Black Blue Brown Blue 10 Fig 10-1 e-STUDIO520/523/600/603/720/723/850/853 WIRE HARNESS CONNECTION DIAGRAMS e-STUDIO520/523/600/603/720/723/850/853 WIRE HARNESS CONNECTION DIAGRAMS © 2005 - 2007 TOSHIBA TEC CORPORATION All rights reserved 10 - H G F E D C MODEM board PC interface (IEEE1284) Speaker Download jig (for FAX) + - CN503 D[0] D[2] D[4] D[6] RD-0 A[0] A[2] A[4] A[6] A[8] A[10] A[12] A[14] A[16] A[18] SG SG D[1] D[3] D[5] D[7] BOOTCS-0 A[1] A[3] A[5] A[7] A[9] A[11] A[13] A[15] A[17] ROMDET0-0 +5.1VA LEDDL-0 CN602 34 33 32 31 30 29 28 27 26 10 25 11 24 12 23 13 22 21 14 15 20 19 16 17 18 18 17 16 19 20 15 14 21 13 22 23 12 11 24 25 10 26 27 28 29 30 31 32 33 34 HRNS-HDD-DES-390 TXB2 RXIN2 CML2-1 LD2 SG ATT3DB2-1 RLADJ12 RLADJ22 SG AG -12VA AG +12VA NC +5.1VA AG CI2-0 ANSDET2 REVA2-0 REVB2-0 NC NC +5.1VA AG +5.1VA -12VA AG +12VA NC NC TXOUT1 RXIN1 CML1-1 LD1 EXTRG ATT3DB1-1 RLADJ11 RLADJ21 RGCLK AG -12VA AG +12VA +12VF 20Hz/16Hz AG CI1-0 ANSDET1 REVA1-0 REVB1-0 INTHOOK-0 EXTHOOK-0 +5.1VA AG +5.1VA -12VA AG +12VA +12VF AG A CN401 SG AG NC NC NC -12VA +12VA NC CN702 +12VF AG NC CN812 CN9 or CN4 CN502 1 2 3 4 5 6 7 8 9 10 10 11 11 12 12 13 13 14 14 15 15 16 16 17 17 18 18 19 19 20 20 21 21 22 22 23 23 24 24 25 25 26 26 27 27 28 28 29 29 30 30 CN9 or CN4 CN501 1 2 3 4 5 6 7 8 9 10 10 11 11 12 12 13 13 14 14 15 15 16 16 17 17 18 18 19 19 20 20 21 21 22 22 23 23 24 24 25 25 26 26 27 27 28 28 29 29 30 30 CN805 CN701 +5.1VA 1 DA1 2 +5.1VA 3 DD0 4 +5.1VA 5 DD3 6 +5.1VA 7 DD6 8 +5.1VA 9 DD9 10 10 SG 11 11 DD12 12 12 SG 13 13 SG 14 14 SG 15 15 SG 16 16 SG 17 17 SG 18 18 +3.3VA 19 19 INTRQ-1 20 20 +3.3VA 21 21 +5.1VA 22 22 -12VA 23 23 SG 24 24 +12VA 25 25 DA0 26 26 DA2 27 27 IDECS1-1 28 28 DD[1] 29 29 DD[2] 30 30 DD[4] 31 31 DD[5] 32 32 DD[7] 33 33 DD[8] 34 34 DD[10] 35 35 DD[11] 36 36 DD[13] 37 37 DD[14] 38 38 DD[15] 39 39 DIOR-0 40 40 DIOW-0 41 41 DMACK-0 42 42 DLDCS0-1 43 43 RESET-0 44 44 DMARQ-1 45 45 NC 46 46 WAKEUP-1 47 47 SG 48 48 SG 49 49 NC 50 50 To Slot [0] or [1] TXOUT2 +5.1VA +12VA +3.3VA MOD2DMA-1 SG MEM2CS-0 +5.1VA MEMRD2-0 CLKOE-1 TXEN2-1 +5.1VA A[16] A[14] A[12] A[10] A[8] A[6] A[4] A[2] A[0] +5.1VA CEP1RST-0 +5.1VA SG CEPCLK SG D[0] D[2] D[4] D[6] D[8] D[10] D[12] D[14] SG MOD2DET-0 SG DREQC2-1 DACKC2-0 RXIN2 AG -12VA AG MD2INT-1 MOD2CS-0 MOD2RST-0 SG RXEN2-1 MEMWRH2-0 MEMWRL2-0 A[18] A[17] A[15] A[13] A[11] A[9] A[7] A[5] A[3] A[1] CPURST-0 CEP2INT-1 +5.1VA +5.1VA IORD2-0 IOWR2-0 D[1] D[3] D[5] D[7] D[9] D[11] D[13] D[15] +5.1VA +5.1VA CEP2CS-0 DREQD2-1 DACKD2-0 Parallel interface kit CN401 CN600 1 2 3 4 5 6 7 8 9 10 10 11 11 12 12 13 13 14 14 15 15 16 16 17 17 18 18 19 19 20 20 21 21 22 22 23 23 24 24 25 25 26 26 27 27 28 28 29 29 30 30 31 31 32 32 33 33 34 34 35 35 36 36 37 37 38 38 39 39 40 40 41 41 42 42 43 43 44 44 45 45 46 46 47 47 48 48 49 49 50 50 51 51 52 52 53 53 54 54 55 55 56 56 57 57 58 58 59 59 60 60 61 61 62 62 63 63 64 64 65 65 66 66 67 67 68 68 69 69 70 70 71 71 72 72 73 73 74 74 75 75 76 76 77 77 78 78 79 79 80 80 BUSY SELECT NACK NFAULT PEERR DATA[0] DATA[1] DATA[2] DATA[3] DATA[4] DATA[5] DATA[6] DATA[7] NINIT NSTROB NSELIN NAUTDF HLH SG SG SG SG SG SG SG SG SG SG SG SG SG SG SG SG SG PLH CN2 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 Scrambler board FAX interface board FAX board B CN2 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 NCU board [Line 1] NCU board [Line 2] CN109 Option To Slot [1] To Slot [0] CN811 NC FAX power relay board TRST# +12VA TMS TD1 +5.1VA INTA# INTC# +5.1VA RESERVED +3.3VA RESERVED +3.3VAUX RST# +3.3VA GNT# SG PME# AD[30] +3.3VA AD[28] AD[26] SG AD[24] IDSEL +3.3VA AD[22] AD[20] SG AD[18] AD[16] +3.3VA FRAME# SG TRDY# SG STOP# +3.3VA RESERVED RESERVED SG PAR AD[15] +3.3VA AD[13] AD[11] SG AD[09] SG SG C/BE[0]# +3.3VA AD[06] AD[04] SG AD[02] AD[00] +3.3VA REQ64# +5.1VA +5.1VA -12VA TCK SG TDO +5.1VA +5.1VA INTB# INTD# PRSNT1# RESERVED PRSNT2# RESERVED SG CLK SG REQ# +3.3VA AD[31] AD[29] SG AD[27] AD[25] +3.3VA C/BE[3]# AD[23] SG AD[21] AD[19] +3.3VA AD[17] C/BE[2]# SG IRDY# +3.3VA DEVSEL# SG LOCK# PERR# +3.3VA SERR# +3.3VA C/BE[1]# AD[14] SG AD[12] AD[10] M66EN SG SG AD[08] AD[07] +3.3VA AD[05] AD[03] SG AD[01] +3.3VA ACK64# +5.1VA +5.1VA A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A14 A15 A16 A17 A18 A19 A20 A21 A22 A23 A24 A25 A26 A27 A28 A29 A30 A31 A32 A33 A34 A35 A36 A37 A38 A39 A40 A41 A42 A43 A44 A45 A46 A47 A48 A49 A50 A51 A52 A53 A54 A55 A56 A57 A58 A59 A60 A61 A62 B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11 B14 B15 B16 B17 B18 B19 B20 B21 B22 B23 B24 B25 B26 B27 B28 B29 B30 B31 B32 B33 B34 B35 B36 B37 B38 B39 B40 B41 B42 B43 B44 B45 B46 B47 B48 B49 B50 B51 B52 B53 B54 B55 B56 B57 B58 B59 B60 B61 B62 Slot [1] : CN803 Slot [0] : CN802 PCI slot A Download jig (for SYS) DDR DIMM 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 CN107 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 CN801 CN116 1 2 3 4 5 6 7 8 9 10 10 11 11 12 12 13 13 14 14 15 15 16 16 17 17 18 18 19 19 20 20 21 21 22 22 23 23 24 24 25 25 26 26 27 27 28 28 29 29 30 30 31 31 32 32 33 33 34 34 35 35 36 36 37 37 38 38 39 39 40 40 41 41 42 42 43 43 44 44 45 45 46 46 47 47 48 48 49 49 50 50 51 51 52 52 53 53 54 54 55 55 56 56 57 57 58 58 59 59 60 60 61 61 62 62 63 63 64 64 65 65 66 66 67 67 68 68 69 69 70 70 71 71 72 72 73 73 74 74 75 75 76 76 77 77 78 78 79 79 80 80 81 81 82 82 83 83 84 84 85 85 86 86 87 87 88 88 89 89 90 90 91 91 92 92 93 93 94 94 95 95 96 96 97 97 98 98 99 99 100 100 101 101 102 102 103 103 104 104 105 105 106 106 107 107 108 108 109 109 110 110 111 111 112 112 113 113 114 114 115 115 116 116 117 117 118 118 119 119 120 120 DATA0 DATA2 DATA4 DATA6 DATA8 DATA10 DATA12 DATA14 A21 A19 A17 A15 A13 A11 A09 A07 A05 A03 RDX CS0-A CS0-B +3.3VA +3.3VA SG SG DATA1 DATA3 DATA5 DATA7 DATA9 DATA11 DATA13 DATA15 A20 A18 A16 A14 A12 A10 A08 A06 A04 A02 A22 /CS +3.3VA RMSL /WRX SG SG +3.3VA +3.3VA +3.3VA SG -12VA -12VA +5.1VA +5.1VA +3.3VA IDSEL0 OPBINT(0) SG IDSEL1 SG PCICLK(3) SG REQ(1) REQ(0) +3.3VA AD[31] AD[29] SG AD[27] AD[25] +3.3VA C/BE[3] AD[23] SG AD[21] AD[19] +3.3VA AD[17] C/BE[2] SG IRDY +3.3VA DEVSEL SG LOCK PERR +3.3VA SERR +3.3VA C/BE[1] AD[14] SG AD[12] AD[10] M66EN SG AD[8] AD[7] +3.3VA AD[5] AD[3] SG AD[1] +3.3VA +5.1VA SG +3.3VA +3.3VA +3.3VA SG +12VA +12VA +5.1VA +5.1VA +3.3VA OPBINT(1) +3.3VA PCIRST +3.3VA PCICLK(4) +3.3VA GNT(1) GNT(0) SG PME AD[30] +3.3VA AD[28] AD[26] SG AD[24] +3.3VA +3.3VA AD[22] AD[20] SG AD[18] AD[16] +3.3VA FRAME SG TRDY SG STOP +3.3VA +3.3VA SG SG PAR AD[15] +3.3VA AD[13] AD[11] SG AD[9] SG C/BE[0] +3.3VA AD[6] AD[4] SG AD[2] AD[0] +3.3VA +5.1VA +5.1VA M +5.1VD APSC-0 SG +5.1VD APS3-0 SG +5.1VD APS2-0 SG +5.1VD APS1-0 SG J23 J22 J21 J20 HOME-SNR (S6) J18 CN3 B7 B8 B9 B4 B5 B6 B1 B2 B3 A7 A8 A9 A4 A5 A6 CN2 A1 A2 A3 CN1 CN115 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 CN8 CN5 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 SCNM-BB +36VC SCNM-B SCNM-AB +36VC SCNM-A +5.1VD +5.1VD SG SG CCDRS-0 SG CCDCP-0 SG CCDSH-0 SG CCDCK2B-0 SG CCDCK2A-0 SG CCDCK1A-0 SG CCD-EVEN-R SG CCD-EDD-R SG CCD-EVEN-L SG CCD-ODD-L SG AG AG AG +12VD +12VD +12VD +3.3VA FRAME CLKRUN TRDY SERR STOP SG +3.3VA PERR DEVSEL C/BE[1] SG AD[14] AD[15] SG AD[13] AD[12] AD[11] AD[10] SG SG AD[09] AD[08] C/BE[0] AD[07] +3.3VA +3.3VA AD[05] AD[06] AD[04] RSV AD[02] AD[03] AD[00] +5.1VA RSV WIP AD[01] RSV WIP SG SG AC SYNC M66EN AC SDATA IN AC SDATA OUT AC BIT CLK AC CODEC ID0 AC CODEC ID1 AC RESET MOD AUDIO MON RSV AUDIO GND SG SYS AUDIO OUT SYS AUDIO IN SYS AUDIO OUT GND SYS AUDIO IN GND AUDIO GND AUDIO GND RSV MPC1ACT VCC5V +3.3VA Download jig (for RADF) SG HOME-0 +5.1VD +5.1VD APSR-0 SG NC +24VE FANSLG-0 DG DG LMPON-0A +24VE +24VE Option J24 J19 2 CN1 CN115 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 JPD/SAD/ASD/ASU/ AUD/MJD/CND/KRD/ TWD model only APS1 (S1) APS2 (S2) APS3 (S3) APS-C (S4) APS-R (S5) J25 CN2 INV-EXP (INV-EXP) SLGFAN-MOT (M23) LP-EXPO (EXP) TIP RING BPMJ-3 BPMJ-1 BPMJ-6 BPMJ-2 BPMJ-7 BPMJ-4 BPMJ-8 BPMJ-5 LED1 GRNP LED2 YELP ENABLE/DISABLE LED2 YELN CHSCND RSV INTB +5.1VA +3.3VA INTA RSV RSV SG +3.3VA CLK RST SG +3.3VA REQ GNT +3.3VA SG AD[31] PME AD[29] RSV SG AD[30] AD[27] +3.3VA AD[25] AD[28] RSV AD[26] C/BE[3] AD[24] AD[23] IDSEL SG SG AD[21] AD[22] AD[19] AD[20] SG PAR AD[17] AD[18] C/BE[2] AD[16] IRDY +3.3VA Wireless LAN adapter 6 J26 CN11 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 2 CN31 DFLD-EXIT-SNR (S68) CN34 DFAPS-SNR (S64) CN29 DFOPN-SNR (S65) CN30 DFREAD-SNR (S69) DF-LD-SOL (SOL5) DENG-SOL (SOL6) DF-SD-SOL (SOL4) CN32 +24V LSOL RSOL +24V +24V SSOL CN4 CN3 +5.1VD SG APS NC CN33 +5.1VD *LOUTS LOUTLED +5.1VD *READS READLED 10 11 12 13 CN54 CN11 +5.1VD SG DFOPNS 4 CN55 +24VG *COPSW C_COM +24VG *DFOPSW DF_COM CN25 NC CN28 CN27 2 CN26 CN24 CN23 2 CN21 DF-COVINTLCK-SW (SW10) CN22 DF-OPNINTLCK-SW (SW9) KMOT_*B KMOT_B KMOT_*A KMOT_A +24V +24V RMOT_*B RMOT_B RMOT_*A RMOT_A +24V +24V CN8 CN9 LMOT_*B LMOT_B LMOT_*A LMOT_A +24V +24V NC SMOT_*B SMOT_B SMOT_*A SMOT_A +24V +24V CN6 CN7 UDMOT_*B UDMOT_B UDMOT_*A UDMOT_A +24V +24V CN5 M DF-FEED-MOT (M37) DF-READ-MOT (M36) DF-L-EXIT-MOT (M39) DF-S-EXIT-MOT (M40) DF-TRY-MOT (M38) M M M M M PWA-F-SLG (SLG) SCAN-MOT (M1) PWA-F-CCD (CCD) PWA-F-SYS (SYS) 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 J3 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 CN109 SG DQ4 DQ5 VDD DM0 DQ6 DQ7 SG NC NC NC VDD DQ14 DQ13 DM1 VDD DQ14 DQ15 CKE1 VDD NC DQ20 A12 SG DQ21 A11 DM2 VDD DQ22 A8 DQ23 SG A6 DQ28 DQ29 VDD DM3 A3 DQ30 SG DQ31 CB4 CB5 VDD CK0 /CK0 SG DMB A10 CB6 VDD CB7 SG DQ36 DQ37 VDD DM4 DQ38 DQ39 SG DQ44 /RAS DQ45 VDD /CS0 /CS1 DMS SG DQ46 DQ47 NC VDD DQS2 DQS3 NC VDD DM6 DQS4 DQS5 VDD NC DQ60 DQ61 SG DM7 DQ62 DQ63 VDD SA0 SA1 SA2 VDD-SPD 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 D0 D2 D4 D6 *RD A0 A2 A4 A6 A8 A10 A12 A14 A16 A18 SG SG D1 D3 D5 D7 *CS2 A1 A3 A5 A7 A9 A11 A13 A15 A17 ROMSEL +5.1VD LED Download jig (for SLG) 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 TXD+ TXDRXIN+ GND GND RXINGND GND INV-LCD (INV-LCD) CN6 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 CN118 DFTRY-VR-SNR (S54) CN44 DFTRY-SNR (S53) CN38 DFSIZE-SNR1 (S56) CN39 DFSIZE-SNR2 (S57) CN40 DFSIZE-SNR3 (S58) CN41 DFRGST-SNR (S55) CN35 DFCOV-SNR (S61) CN36 DFEMP-SNR (S60) CN37 DFU-LMT-SNR (S59) PWA-F-ADF (ADF) 20 19 18 17 16 15 14 13 12 11 10 MDT[0] MDT[2] MDT[4] MDT[6] MRD-0 MAD[0] MAD[2] MAD[4] MAD[6] MAD[8] MAD[10] PNLDT1 PNLDT3 MAD[16] MAD[18] SG SG MDT[1] MDT[3] MDT[5] MDT[7] PNLCS-0 MAD[1] MAD[3] MAD[5] MAD[7] MAD[9] PNLDT0 PNLDT2 MAD[15] MAD[17] ROMDT-0 +5.1VD LED CN43 12 11 10 CN45 CN46 10 11 12 4 CN42 CN9 10 11 CN10 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 PWA-F-KEY2 (KEY2) 10 11 12 CN13 +5.1VD TRVR SG NC CN14 +5.1VD SG TRYS +5.1VD SG REGS +5.1VD SG SIZS3 +5.1VD SG SIZS2 +5.1VD SG SIZS1 +5.1VD SG ULMTS +5.1VD SG EMPS CN12 +5.1VD SG COPS 3 7 +5.1VD SG CSEN NC CN114 +12VA SG SG +5.1VA +5.1VD *SSBS SSBLED CN51 CN50 +24V PWRFN-0A CN53 DF2 SD-REV-SNR (S66) CN52 DF2 SD-EXIT-SNR (S67) CN49 DF2 MID-TR-SNR (S70) CN48 DF2 LENG-SNR (S63) CN1 CN2 CN404 +36VD PG +24VE DG +24VG +24VG DG DG +24V PWRFN-0A CN408 CN405 20 19 18 17 16 15 14 13 12 11 10 CN171 4 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 CN170 +3.3VC SG +5.1VD +5.1VD SG SG +12VD AG PWRDWN-1 +3.3VA +3.3VA SG SG +5.1VA +5.1VA +5.1VB SG SG SG AG AG PWR-DN +12VB PWR-EN +12VA NC NC NC NC CN47 DF2 L-LMT-SNR (S62) PS-FAN-MOT2 (M35) M CN101 10 15 16 11 14 12 13 PWA-F-DSP (DSP) A CN113 /RESET SG DD7 DD8 DD6 DD9 DD5 DD10 DD4 DD11 10 DD3 11 DD12 12 DD2 13 DD13 14 DD1 15 DD14 16 DD0 17 DD15 18 SG 19 NC(KEY) 20 MDARQ 21 SG 22 /DIOW 23 SG 24 /DIOR 25 SG 26 IORDY 27 SG 28 /DMACK 29 SG 30 INTRQ 31 NC(RESERVED) 32 DA1 33 /PDIAG 34 DA0 35 DA2 36 /CS0 37 /CS1 38 /DASP 39 SG 40 Standard PS-FAN-MOT1 (M34) +5.1VD *LNGS LNGLED CN16 +5.1VD SG SHS 10 CN5-2A M NC 18 18 NC 19 19 NC 20 20 J501 8 9 10 10 11 11 12 12 13 13 14 14 15 15 16 16 17 17 CN15 +5.1VD SG DLMTS FG J17 6 5 4 3 2 1 CN102 SG 26 SG 25 EXPON-0 24 +3.3VC 23 SG 22 SYSRST-0 21 SG 20 SRTS-0 19 SRXD-1A 18 STXD-1 17 SCTS-0A 16 SG 15 SG 14 TX0-0 13 TX0-1 12 SG 11 TX1-0 10 TX1-1 SG TX2-0 TX2-1 SG CLK-1 CLK-0 SG SG TCP (TCP) +3.3VC SG +5.1VD SG +12VD AG +24VE DG +36VD PG PWRDWN-1 LAN connector (10BASE-T/ 100BASE-TX) Option CN112 VDD NC NC D4 D+ NC NC DETACH NC SG 10 NC 11 NC 12 /RESET 13 NC 14 NC 15 NC 16 NC 17 NC 18 NC 19 SG 20 LCD(LCD) CN4 10 CN1 10 CN4-2 CN4-1 CN6 INV_VDD5V INV_CONT INV_GND CN1 CN2 4 J16 DFAK-0 1 DFSCST-0 2 DFRXD-0 3 SG 4 DFTXD-0 5 SG 6 DFRAK-0 7 DFRRQ-0 8 DFRQ-0 9 DFCNT-0 10 10 NC 11 11 Bluetooth module 12 13 NC 14 15 16 17 18 NC 19 20 12 13 14 15 16 17 18 19 20 CN2 FG CN2 10 11 12 13 14 INV_VDD5V INV_GND OUTP4PW OUTP3PW COM2PW RET8 RET7 RET6 SCN4 LW MID UP INV_CONT FG 10 11 12 13 14 10 11 12 13 PWA-F-KEY1 (KEY1) 4 HDD (HDD) CN407 +5.1VE +5.1VF SG SG +3.3VB +12VC SG AG PWR-DN CN403 +24VD DG +36VC PG +5.1VH SG SG +5.1VH +5.1VH SG DDISO2-1 WRAPC2-0 SG LVDS2-0 LVDS2-1 SG SG WRLV2-1 SG +5.1VH +5.1VH SG J201 16 15 14 13 12 11 10 10 11 12 13 14 15 NC 16 10 11 12 13 14 15 16 J417 1 2 3 4 5 6 7 8 9 NC SG +5.1VH +5.1VH SG DDISO1-1 WRAPC1-0 SG LVDS1-0 LVDS1-1 SG SG WRLV1-1 SKHSLV1-1 +5.1VH +5.1VH SG J201 16 15 14 13 12 11 10 3 14 12 10 CN211 15 16 13 11 J208 10 11 12 13 14 15 16 J207 10 11 12 13 14 15 16 J213 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 VBUS0 DD+ SG VBUS1 DD+ SG CN117 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 VBUS0 DD+ SG VBUS1 DD+ SG CN111 e-STUDIO850/853 PWA-F-LDR2 (LDR2) PWA-F-LDR1 (LDR1) Internal USB connector (for Data overwrite kit) USB connector (Host) USB connector (Device) VBUS DD+ SG CN110 SE_VCC SE_VOUT SE_GND SE_TOUT M TNR-MOTINTLCK-SW (SW11) Option J502 2 J670 10 6 10 1 M PWA-F-SNS (SNS) POL-MOT (M2) NC NC NC NC Finisher M MIR-GLV (GLV) PWA-F-SNS (SNS) POL-MOT (M2) e-STUDIO850/853 CN212 GLV2-0 GLV2-1 J217 J215 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 J210 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 SG SG +5.1VF +5.1VF +5.1VF BMRST-0 BMSW3-0 BMSW2-0 BMSW1-0 BMSW0-0 CSEXT-0 LVCNT-0 OSEL-0 BMDIN-1 BMSCK-1 CSINT-0 DOUT EOUT MOUT NOUT +5.1VF NC OUTAB-0 +5.1VF NC BMCK-0 +5.1VF EOCNV-0 RSTITG-0 WLOWL-0 WUPPL-0 +5.1VF +5.1VF SG SG CN206 PMCLK-1A PMOK-0A PMON-0A DG +24VD e-STUDIO520/523/600/603/720/723 CN203 CN202 +5.1VE BEAMDT-0 2 SG CN209 27V DG PMON-0A PMOK-0A PMCLK-1A M Coin controller SYS-FAN-MOT (M33) CN204 IDATX4 IDATX3 IDATX2 IDATX1 IDATX0 SG MVDEN RGTAS PLRST LSBSY 10 LCTS 11 LRTS 12 LRXD 13 LTXD 14 IVSYNC 15 IHSYNC 16 SG 17 IRCLK 18 SG 19 IVDEN 20 SG 21 IHDEN 22 SG 23 IDCLK 24 SG 25 IDATX7 26 IDATX6 27 IDATX5 28 Option PS-ACC (PS) A B J501 U-FRNT-COV-SW (SW7) CN108 +12VA SG D[0] D[2] D[4] D[6] RD-0 A[0] A[2] A[4] A[6] A[8] A[10] A[12] A[14] A[16] A[18] SG SG D[1] D[3] D[5] D[7] CS2-0 A[1] A[3] A[5] A[7] A[9] A[11] A[13] A[15] A[17] ROMDT +5.1VE LED-1 J592 3 CN806 12 11 10 CN104 14 13 12 11 10 28 27 26 25 24 23 22 21 20 19 18 17 16 15 J503 1 2 3 4 J628 1 2 3 4 5 6 7 8 9 10 10 11 11 12 12 13 13 14 14 15 15 16 16 17 17 18 18 SFBCOV-SNR (S25) J517 J599 ATTRN-SNR (S12) J613 3 J558 FEEDCOV-SNR (S26) J505 TNR-TR-MOT (M6) NC A B J504 TNREMP-SNR (S10) TNR-SW (SW2) TNR-MOT (M5) SE_VCC SE_VOUT SE_GND SE_TOUT TEMP/HUMI-SNR (S7) CN106 L/S FULL-C NONO-C B/W +5.1VA SG NC M CN7 CN8 CN1 2 CN410 +12VF NC AG DISP FRM LOAD CP VDD VSS DF D0 D1 D2 D3 VEE VLCD CN5-2B CN5-1B FG SE_TOUT SE_GND SE_VOUT SE_VCC RET1 SCN1 SCN2 SCN3 SCN4 OUTP8 OUTP7 OUTP6 OUTP5 OUTP4 OUTP3 OUTP2 OUTP1 COM1 COM2 Download jig (for PLG) 10 11 12 13 26 25 24 23 22 21 20 19 CN5-1A SG RET8 RET7 RET6 RET5 RET4 RET3 RET2 10 11 12 13 14 15 16 17 18 19 20 10 11 12 13 14 15 16 17 18 19 20 CN1 A15 A14 A13 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 B15 B14 B13 B12 B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 J526 A15 A1 A14 A2 A13 A3 A12 A4 A11 A5 A10 A6 A9 A7 A8 A8 A9 A7 A6 A10 A5 A11 A4 A12 A3 A13 A2 A14 A1 A15 B15 B1 B14 B2 B13 B3 B12 B4 B11 B5 B10 B6 B9 B7 B8 B8 B7 B9 B6 B10 B5 B11 B4 B12 B3 B13 B2 B14 B1 B15 CN105 XSCL-1A A1 LP-1A A2 WF-1A A3 YP-1A A4 SG A5 BZON-0A A6 CPPOW-0A A7 LDCLKA A8 LDDAT-0A A9 LDLTH-0A A10 LDON1-0A A11 LDON0-0A A12 SG A13 +5.1VA A14 +5.1VA A15 +5.1VA B1 +5.1VA B2 CPRST-0A B3 SG B4 RTS0-0A B5 CTS0-0A B6 SOUT0-0A B7 SIN0-0A B8 SG B9 UD3-1A B10 UD2-1A B11 UD1-1A B12 UD0-1A B13 SG B14 LCDEN-1A B15 VREF DQ0 SG DQ1 DQS0 DQ2 VDD DQ3 NC NC SG DQ8 DQ9 DQS1 VDD CK1 /CK1 SG DQ10 DQ11 CKE0 VDD DQ16 DQ17 DQS2 SG A9 DQ18 A7 VDD DQ19 A5 DQ24 SG DQ25 DQS3 A4 VDD DQ26 DQ27 A2 SG A1 CB0 CB1 VDD DQS8 A0 CB2 SG CB3 BA1 DQ32 VDD DQ33 DQS4 DQ34 SG BA0 DQ35 DQ40 VDD /WE DQ41 /CAS SG DQ55 DQ42 DQ43 VDD NC DQ48 DQ49 SG /CK2 CK2 VDD DQS6 DQ50 DQ51 SG VDD-ID DQ56 DQ57 VDD DQS7 DQ58 DQ59 SG NC SDA SCL CN810 PWA-F-PLG (PLG) 06/09 CN409 NC DG +24VF +24VF SG +5.1VG 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 NC CN330 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 12 13 14 15 16 17 18 19 20 SG +5.1VC AD0 AD2 AD4 AD6 I/O0 I/O2 I/O4 I/O6 SG WE CSIP2-0A +5.1VC IPCSW-0 SG +5.1VC AD1 AD3 AD5 AD7 I/O1 I/O3 I/O5 I/O7 SG OE RST-0 VDD SG +24VB TOLON-0A KCTRC-1A MCRUN-0A EXTCTR-0A DG BKCTR-0A MNCTR-0A SG SIZE3-0A SIZE2-0A SIZE1-0A SIZE0-0A +5.1VC CTRCN2-0 PD[0] PD[2] PD[4] PD[6] PRD-0 PA[0] PA[2] PA[4] PA[6] PA[8] PA[10] PA[12] PA[14] PA[16] PA[18] SG SG PD[1] PD[3] PD[5] PD[7] PBOOTCS PA[1] PA[3] PA[5] PA[7] PA[9] PA[11] PA[13] PA[15] PA[17] PROMDETO-0 +5.1VC PLED-1 CN325 34 33 32 31 30 29 28 27 26 25 10 24 11 23 12 22 13 21 14 20 15 19 16 18 17 17 18 16 19 15 20 14 21 13 22 12 23 11 24 10 25 26 27 28 29 30 31 32 33 34 CN344 10 NC 11 D[0] D[2] D[4] D[6] RD-0 A[0] A[2] A[4] A[6] A[8] A[10] A[12] A[14] A[16] A[18] SG SG D[1] D[3] D[5] D[7] BOOTCS A[1] A[3] A[5] A[7] A[9] A[11] A[13] A[15] A[17] ROMDETO-0 +5.1VC LED-1 CN342 12 11 10 24 23 22 21 20 19 18 17 16 15 14 13 B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11 B12 B13 B14 B15 B16 A14 A15 A16 A10 A11 A12 A13 A4 A5 A6 A7 A8 A9 CN338 A1 A2 A3 CN324 34 33 32 31 30 29 28 27 26 25 10 24 11 23 12 22 13 21 14 20 15 19 16 18 17 17 18 16 19 15 20 14 21 13 22 12 23 11 24 10 25 26 27 28 29 30 31 32 33 34 TNMTON-0A TNMTCW-0A +5.1VC DG +24VB HOPSW-1A SG +5.1VC TNRES-0 SG DG +24VB TNHMLK-0 TNHMON-0A UFTCS-0 SG SG SDCOV-1A +5.1VC +5.1VC HUMIS-1A SG TEMPS-1A ATSSW-1 ATSVR-1A +24VB ATS-1A SG SG SG SFCOV-1A +5.1VC IPC board (Finisher) CN402 +24VA +24VB +24VC DG DG DG +36VA +36VB PG PG 10 PWRFN-0A 11 CN406 +3.3VD +5.1VC SG SG PWR-DN +12VE AG CN103 LTXD LRXD LRTS LCTS LSBSY PLRST RGTAS MVDEN SG CMD 10 CBSY 11 CACK 12 CERR 13 SG 14 STS 15 SBSY 16 SACK 17 SERR 18 SG 19 MCNT 20 SYSRST 21 EXPON 22 +5.1VC 23 +3.3VD 24 CN805 CNT-GND 10 F-CNT NC NC NC NC SG TXD SG RXD FG A3 A2 A1 A14 A15 A16 B16 B15 B14 B13 B12 B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 A7 A6 A5 A4 A10 A11 A12 A13 B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11 B12 B13 B14 B15 B16 A13 A12 A11 A10 A9 A8 A4 A5 A6 A7 A8 A9 J635 A1 A16 A2 A15 A3 A14 Download jig (for MAIN) Download jig (for PFC) DG +24VB RTNMTLK-0 RTNMTON-0A RSTSW-0A +24VB NC NC NC NC WCLMTB-0A WCLMTA-0A +24VB ERSLP-0A SG MCLSW-0A CLNSW-0A SG DRTH-0A SG +12VE AG CTDVR-1A CTDVD-1A CTDVC-1A NC NC NC NC NC DG +24VB RTNHMLK-0 RTNHMON-0A DCTIF-0A +24VA LDFAN-0A +24VA DVMBK-0A +5.1VC DEVMON-0A SG +5.1VC DEVCK-1A DG DG +24VA +24VA DCTF2-0A +24VA SG TFUSW-1A +5.1VC TCMTA-0A TCMTB-0A +5.1VC TRCS1-0A SG +5.1VC TRCS2-0A SG J596 J549 LSU-FAN-MOT (M32) DEV-MOT (M10) A5 A6 A7 A8 A9 A10 A11 A12 SG TFUSW-1A +5.1VC NC TCMTA-0A TCMTB-0A +5.1VC TRCS1-0A SG +5.1VC TRCS2-0A SG RGTA-0A +24VC RGTC-0A RGTB-0A +24VC RGTD-0A CPSW2-0 SG M PS-HVT (HVT) M M M TRB-MOT (M14) M M OUT5 A OUT4 C D D REV-MOT (M19) M B Magnetic roller F Transfer belt cleaning brush E Transfer belt power supply roller D Grid OUT2 C OUT3 A B Main charger wire M J621 1 TRB-CAM-MOT (M15) 2 J622 TRB-SNR1 (S16) J623 TRB-SNR2 (S15) OUT1 A B B J596 USD-TNRFLL-SNR (S11) J549 4 M * Pins 2, 4, 6, and 10 are NC 11 * Pins 2, 4, 6, and 10 are NC 11 DRM-MOT (M11) J604 THMS-DRM (THM5) J610 TNR-LVL-SNR (S14) * Pins 2, 4, 6, and 10 are NC 11 LP-ERS (ERS) M B CH-CLN-POS-SW (SW4) A J602 CN1 1 J589 RGST-SNR (S18) J609 RGST-MOT (M16) CN422 +36VB +36VB TRMA-0 TRMBB-0 TRMB-0 TRMAB-0 CN421 +36VB +36VB DRMA-0 DRMBB-0 DRMB-0 DRMAB-0 e-STUDIO600/850 e-STUDIO603/853 B9 B10 B11 B12 M M NC 10 M 10 DCT-I-FAN-MOT (M30) J595 10 FUS-FAN-MOT (M28) DEV-FAN-MOT (M31) CN341 NC A1 SG A2 PSTPS-1 A3 +5.1VC A4 J559 NC CN351 PFMON-0A SG +5.1VC PFMCK-1A FEED-MOT (M20) PG PG +36VA +36VA CN412 12 11 10 J618 2 1 J616 2 1 B1 B2 B3 B4 B5 B6 B7 B8 Not used SPRT-FING-SOL (SOL1) J590 J632 9 8 7 6 MAIN-SW (SW6) M M PWA-F-LGC (LGC) J594 HOP-MOT (M7) NC J593 RCY-TNR-MOT (M8) NC DEV-SW (SW3) J601 CH-CLN-MOT (M12) B A J524 J653 6 5 4 3 2 1 8 J507 J629 1 2 3 4 B A CN605 DRUM-SUF-SNR (S13) 2 J633 3 J515 DRM-CLN-MOT (M13) NC NC NC NC NC NC M PWA-F-MOT (MOT) Option Copy Key Card CN347 HVTAC-0A HVTER-0 HVTM-0A HVTVR-1A HVTT-0A HVTBB-0A HVMVR-1A DG +24VB HVDVR-1A 10 HVDAC-0A 11 HVDDC-0A 12 CN343 15 14 13 12 11 10 8 10 11 12 13 14 15 e-STUDIO520/720 e-STUDIO523/723 B9 B10 B11 B1 B2 B3 B4 B5 B6 B7 B8 RGTA-0A +24VC RGTC-0A RGTB-0A +24VC RGTD-0A NC NC J589 J609 11 CN420 17 16 15 14 13 12 11 10 2 J600 2 1 J570 2 1 DG +24VB DFURMLK-0 DFURMON-0A DEVFA-0A +24VA J598 2 A11 A12 A13 A14 A15 A16 A17 A18 A19 A20 B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11 B12 B13 B14 B15 B16 B17 B18 B19 B20 A7 A8 A9 A10 A5 A6 J597 2 1 CN341 SG A1 PSTPS-1 A2 +5.1VC A3 A4 A5 A6 A7 A8 A9 A10 A11 A9 A8 A7 A6 A5 A4 A3 A2 A1 A20 B19 B18 B17 B16 B15 B14 B13 B12 B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 B20 A13 A12 A11 A10 A15 A14 NC NC NC NC EXIT-MOT (M18) J624 A19 A1 A18 A2 A17 A3 A16 A4 J619 +24VA SCRP-0A CN340 +36VB +36VB PG PG DRCLK-0A DRVRST-0 DRMVR-0A DRMEN-1A DRMCW-0A +5.1VC 10 SG 11 TRMCK-0A 12 TRMVR-0A 13 TRMEN-1A 14 TRMCW-0 15 PG 16 +36VB 17 B13 B14 B11 B12 B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 A13 A14 A11 A12 A7 A8 A9 A10 A5 A6 CN339 SG A1 KCTRC-1A A2 +24VA A3 KCTRON-0A A4 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 10 SG DEVSW-0A CN337 DG SG DRV0-1A +24VB CN336 +24VB +24VB EXTMA-0A EXTMC-0A EXTMB-0A EXTMD-0A 6 +24VB +24VB MTMA-0 MTMBB-0 MTMB-0 MTMAB-0 M M M EXIT-FAN-MOT (M29) M J528 2 1 Option External LCF J850 12 13 14 15 16 17 18 19 20 21 22 10 10 11 PWA-FMOT2-RV (MOT2-RV) J561 2 1 J562 REV-SNR1 (S23) J563 REV-SNR2 (S24) J567 EXIT-SNR (S22) J568 EXIT-COV-SW (SW5) J564 2 REV-FAN-MOT1 (M24) 1 J565 2 REV-FAN-MOT2 (M25) 1 GATE-SOL (SOL2) J415 J569 2 1 J571 2 1 CN455 14 13 12 11 10 J532 2 1 J529 2 HRZ-DR-CLT2 (CLT2) 1 J530 2 HRZ-DR-CLT3 (CLT3) 1 J533 HRZ-TR-SNR1 (S19) J534 HRZ-TR-SNR2 (S20) J535 HRZ-TR-SNR3 (S21) HRZ-DR-CLT1 (CLT1) IH-FAN-MOT (M26) PWA-F-IH (IH) M M SG P2BTM-1A +5.1VC PLTRM-0A PLTRM-1A SG P3BTM-1A +5.1VC SG P4BTM-1A +5.1VC J551 J555 2 1 J643 J644 CST4BTM-SNR (S48) CST3BTM-SNR (S42) CST-TRY-MOT2 (M22) J420 11 10 7 FG J516 USD-TNR-MOT (M9) NC J585 10 FUS-MOT (M3) DCT-O-FAN-MOT (M27) M J579 2 1 J580 WEB-SNR (S8) J581 3 2 WEB-MOT (M4) 4 1 THMS-L-HTR (THM4) J577 FUS-TR-SNR (S9) J578 8 THMS-R-HTR (THM3) 5 4 7 THMS-F-HTR (THM1) 6 3 2 THMS-C-HTR (THM2) 1 M SG P1BTM-1A +5.1VC J550 CST1BTM-SNR (S30) CST2BTM-SNR (S36) PUTRM-0A PUTRM-1A J554 2 1 CST-TRY-MOT1 (M21) NC NC NC NC NC NC NC NC NC NC NC NC NC B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 A9 A8 A7 A6 A5 A4 A3 A2 A1 B12 B11 10 9 10 11 12 13 14 15 16 17 18 J822 14 14 15 15 16 16 17 17 18 18 19 19 20 20 21 21 22 22 23 23 24 24 3 4 5 6 7 8 9 10 10 11 11 12 12 13 13 2 1 J560 11 10 6 10 11 13 12 11 16 15 14 J614 18 17 B14 B13 B12 B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 B7 B8 B9 B10 B11 B12 B13 B14 B15 B16 B17 B18 B19 B20 J611 A1 A20 A2 A19 A3 A18 A4 A17 A5 A16 A6 A15 A7 A14 A8 A13 A9 A12 A10 A11 A11 A10 A12 A9 A13 A8 A14 A7 A15 A6 A16 A5 A17 A4 A18 A3 A19 A2 A20 A1 B1 B20 B2 B19 B3 B18 B4 B17 B5 B16 B6 B15 J584 3 J615 3 B3 B4 B5 B6 B7 B8 B9 B10 B11 B12 A4 A5 A6 A7 A8 A9 A10 A11 A12 B1 B2 J645 A1 A12 A2 A11 A3 A10 FG SG DG PFCPM2-0A PFCPM1-0A LC-FCLT-0 LCPCLT-0 LCFDMB-0A LCFDMA-0A LCTRMB-0A LCTRMA-0A +24VC +24VC LCFINT-0 LC-FEED LC-PICK LC-TRAYUP LC-BTH LC-CST LC-PEMP LC-SET LC-JUDGE +5.1VC NC +24VB +24VB DG DG REVMC-0A DRVRST-0 RVNVR-0A REVME-0A REVCW-0A +5.1VC SG NC NC NC NC NC NC NC ADUFA2-0A +24VC SG EXCSW-1A +5.1VC ADUFA1-0A +24VC SG EXTSW-1A +5.1VC SG REVS2-1A +5.1VC SG REVS1-1A +5.1VC STKSL-0A +24VC SG ADTR1-1A +5.1VC SG ADTR2-1A +5.1VC SG ADTR3-1A +5.1VC SG ADCNT-1A ATRC4-0A +24VC ATRC1-0A +24VC ATRC2-0A +24VC H1EER3-0 H1EER2-0 H1EER1-0 IHDUTY-1A SG IH1ON-1 H2PWR3-0A H2PWR2-0A H2PWR1-0A H1PWR3-0A H1PWR2-0A H1PWR1-0A +5VSW IH2ON-1 IHFAN-0A +24VC NC HTRMT-0C SG HTRML-0A SG +5.1VC HTRCK-1A PG PG +36VA +36VA DG +24VB AGMLK-0 AGMON-0A +24VC DCTOF-0A +24VC RVSFA-0A SG WEBED-0 +5.1VC WEBMTB-0A WEBMTA-0A +5.1VC WEBCN-0 SG NC NC +5VSW STH 1A STH+-1A ETH 1A ETH+-1A MTH 1A MTH+-1A FUSSW-1A NC PTH 1A PTH+-1A SG HEXTS-1A +5.1VC CN346 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 17 18 12 13 14 15 16 10 11 CN335 B7 B8 B9 B10 B11 B12 B13 B14 B15 B16 B17 B1 B2 B3 B4 B5 B6 CN334 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 10 11 12 13 14 15 16 17 18 CN333 B3 B4 B5 B6 B7 B8 B9 B10 B11 B12 A4 A5 A6 A7 A8 A9 A10 A11 A12 B1 B2 CN332 A1 A2 A3 B6 B7 B8 B3 B4 B5 B1 B2 A6 A7 A8 A3 A4 A5 CN331 A1 A2 JPD/NAD/SAD/DAU/DMJ/TWD(e-STUDIO600/720) model only NAD/DMJ(e-STUDIO603/723) model only M M +24VB +24VB DG DG MTMCK-0A DRVRST-0 MTMRF-0A MTMEN-0A NC +5.1VC SG +24VC SFBC-0A NC NC SG RGTAS-1 +5.1VC SG SFBS0-1A SFBS1-1A SFBS2-1A SFBS3-1A +5.1VC SFBSW-1A SG SG P2FED-1A +5.1VC +24VC P2FDC-0A +24VC P2RGC-0A SG PCST2-1A +5.1VC SG P2RGT-1A +5.1VC SG P2TOP-1A +5.1VC SG P2EMP-1A +5.1VC SG P1FED-1A +5.1VC +24VC P1FDC-0A +24VC P1RGC-0A SG PCST1-1A +5.1VC SG P1RGT-1A +5.1VC SG P1TOP-1A +5.1VC SG P3FED-1A +5.1VC +24VC P3FDC-0A +24VC P3RGC-0A NC SG PCST3-1A +5.1VC TPUSL-0A +24VC SG P3RGT-1A +5.1VC SG P3TOP-1A +5.1VC SG P4FED-1A +5.1VC +24VC P4FDC-0A 10 11 21 22 23 24 19 20 16 17 18 12 13 14 15 +5.1VC TLLEMP-1A SG TLTRM-0A TLTRM-1A TEFSL-0A +24VC TLCFS-1A +5.1VC 10 11 12 13 14 B9 B10 B11 B7 B8 B5 B6 A7 A8 A9 A10 A11 B1 B2 B3 B4 A4 A5 A6 B9 B10 B11 B7 B8 B5 B6 B1 B2 B3 B4 A10 A11 A7 A8 A9 A4 A5 A6 B3 B2 B1 B5 B4 B7 B6 A5 A4 A3 A2 A1 B11 B10 B9 B8 A8 A7 A6 B9 B10 B11 B7 B8 B5 B6 A7 A8 A9 A10 A11 B1 B2 B3 B4 A4 A5 A6 J642 A11 A1 A10 A2 A9 A3 B3 B2 B1 B5 B4 B7 B6 B11 B10 B9 B8 A2 A1 A5 A4 A3 A8 A7 A6 J641 A11 A1 A10 A2 A9 A3 B3 B2 B1 B5 B4 B7 B6 A5 A4 A3 A2 A1 B11 B10 B9 B8 A8 A7 A6 NC NC NC NC CST2-TR-CLT (CLT7) CST2-SNR (S35) CST2TR-SNR (S39) CST2TRY-SNR (S38) CST2FEED-SNR (S40) LCF-PICK-SOL (SOL7) J536 CST3EMP-SNR (S43) J537 CST3TRY-SNR (S44) J538 CST3 TR-SNR (S45) CST2-FEED-CLT (CLT8) 3 CST2EMP-SNR (S37) CST1FEED-SNR (S34) 2 1 2 1 2 1 J541 2 1 J542 CST4-TR-CLT (CLT11) CST4-SNR (S47) CST4TR-SNR (S51) CST4TRY-SNR (S50) CST4EMP-SNR (S49) CST4FEED-SNR (S52) CST4-FEED-CLT (CLT12) 3 3 J539 CST32 FEED-SNR (S46) CST3-FEED-CLT (CLT10) CST3-TR-CLT (CLT9) J540 CST3-SNR (S41) 14 13 12 16 15 19 18 17 22 21 20 NC NC NC J588 LCF-TRY-MOT (M41) B3 B2 B1 B5 B4 B8 B7 B6 A5 A4 A3 A2 A1 B11 B10 B9 A8 A7 A6 J503 A11 11 A10 10 A9 M J507 LCF-ENDF-MOT M (M42) J511 1 LCF-ENDF-SOL (SOL8) 2 J509 LCF-ENDFHP-SNR (S73) J510 LCF-ENDFSTP-SNR (S75) J508 LCFEMP-SNR (S74) J512 LCFMST-SNR (S72) J506 LCFBTM-SNR (S71) J519 MT-MOT (M17) M Tandem LCF 4th drawer 3rd drawer 2nd drawer 1st drawer * Pins 2, 4, 6, and 10 are NC 11 SFBSIZE-SNR (S28) J518 SFB2 FEED-SNR (S27) CN424 +24VB +24VB MTMA-0 MTMBB-0 MTMB-0 MTMAB-0 TNA/ASD/ASU/ARD/AUD/MJD/CND/ KRD/TWD(e-STUDIO850) model only J543 2 1 2 1 CST1-TR-CLT (CLT5) CST1-SNR (S29) CST1TR-SNR (S33) CST1TRY-SNR (S32) CST1EMP-SNR (S31) PWA-FMOT2-MT (MOT2-MT) CST1-FEED-CLT (CLT6) 2 1 2 1 2 1 J640 A11 A1 A10 A2 A9 A3 NC NC NC NC NC NC 3 3 B7 B8 B5 B6 A7 A8 A9 A10 A11 B1 B2 B3 B4 A4 A5 A6 J583 11 10 3 J557 MID-TR-SNR (S17) B9 B10 B11 B3 B2 B1 B5 B4 B7 B6 A5 A4 A3 A2 A1 B11 B10 B9 B8 A8 A7 A6 J639 A11 A1 A10 A2 A9 A3 11 10 J517 SFB-SOL (SOL3) J514 3 J516 2 SFB-FEED-CLT (CLT4) 1 J515 2 1 TNA/ASD/ASU/ARD/AUD/MJD/CND/KRD/ TWD(e-STUDIO850) model only TLTMM-0A TLTMM-1A +5.1VC TLTGE-1A SG NC +5.1VC TLTGS-1A SG +5.1VC TLEGC-1A SG 11 12 10 J527 14 13 12 10 J513 12 11 JPD/NAD/SAD/DAU/DMJ/ TWD(e-STUDIO600/720) model only +24VC P4RGC-0A SG PCST4-1A +5.1VC SG P4RGT-1A +5.1VC SG P4TOP-1A +5.1VC CN345 +5.1VC TLFBTM-1A SG 17 18 19 15 16 13 14 10 11 12 CN350 SG P4EMP-1A +5.1VC 20 21 22 18 19 16 17 12 13 14 15 10 11 CN328 SG P3EMP-1A +5.1VC 36 37 38 34 35 32 33 29 30 31 26 27 28 23 24 25 20 21 22 17 18 19 15 16 13 14 10 11 12 CN329 SG P1EMP-1A +5.1VC B4 B5 B6 B7 B8 B9 B10 B11 B12 B13 B14 A11 A12 A13 A14 B1 B2 B3 A6 A7 A8 A9 A10 A3 A4 A5 CN327 +24VC A1 SFBSL-0A A2 H G F E D C B A 10.2 DC Wire Harness 10.3 Electric Parts Layout 1) Scanner unit a A4 series 1) Scanner unit c Heater, thermostat S5 2) Control panel 3) Laser unit a e-STUDIO520/523/600/603/720/723 3) Laser unit b e-STUDIO850/853 4) Fuser related section M1 S4 M23 INV-EXP THM3 SLG S6 KEY2 THMO3 SW1 THMO1 THM1 LDR1 LDR1 INV-LCD DH2 M3 THM2 THMO2 LDR2 CCD S7 S3 S1 EXP PLG S2 M4 KEY1 PLG DH1 IH-COIL TCP/LCD 1) Scanner unit b LT series GLV S9 S5 M1 DSP S4 M23 INV-EXP M2 M2 SNS SNS S8 THM4 SLG S6 CCD S3 EXP S2 5) Toner cartridge related section 6) Toner recycle / used toner recovery unit 7) Developer unit / drum/ transfer belt unit related section a Motor, sensor, switch, solenoid, lamp, thermistor 8) Paper transport unit 9) Paper exit / reverse section S13 M10 S22 S18 M16 S12 M11 SW2 7) Developer unit / drum/ transfer belt unit related section b Heater, thermostat, PC board S23 DH3 SW4 S11 M5 SW3 M13 S17 M14 CLT3 M8 S10 M17 SOL1 M9 CLT2 THM5 M18 S15 M7 CLT1 M6 M12 S16 M24 ERS M19 S14 M15 11) Equipment (right view) 12) Bypass feed unit SOL2 M25 S20 FUS THMO4 10) Equipment (left view) MOT2-RV S21 S24 SW5 S19 13) Paper feeding section 14) Tandem LCF 15) Equipment (rear view) M32 SW6 S27 M27 S31 SW11 M30 SW7 M28 S30 MOT S32 S33 CLT4 HDD M21 SOL7 S34 S72 SOL3 M31 CLT5 M29 S28 IH CLT6 S29 CLT7 CLT8 S35 M20 S39 S38 S37 S36 S40 S25 S45 MOT2-MT S44 S43 M26 S48 S49 S50 S51 S52 S42 S46 S26 16) AC input section a e-STUDIO600/720: JPD model 16) AC input section b e-STUDIO850: JPD model 16) AC input section c e-STUDIO520: TNA/NAD model, e-STUDIO600/720: TNA/NAD/SAD/TWD model, e-STUDIO850: TNA/NAD/SAD model, e-STUDIO523/603/723/853: TNA/NAD model HVT SYS M42 CLT9 CLT10 S41 S47 SW8 M33 SOL8 M41 CLT11 CLT12 M34 S73 M22 LGC M35 S71 S74 PS S75 16) AC input section d e-STUDIO520: AUD/DAU/MJD/DMJ model, e-STUDIO600/720/850: ARD/AUD/DAU/MJD/DMJ/CND/KRD model, e-STUDIO850: TWD model e-STUDIO523/603/723/853: ARD/MJD/DMJ/CND model 17) Reversing automatic document feeder (RADF) a Sensor 17) Reversing automatic document feeder (RADF) c Motor, sensor, switch, solenoid, PC board SW10 SOL4 M40 SW9 ADF M37 S53 M36 S54 S57 S64 S56 M38 S55 S58 17) Reversing automatic document feeder (RADF) b Sensor NF1 NF1 S61 NF1 S60 SOL6 M39 S65 SOL5 17) Reversing automatic document feeder (RADF) d Sensor S59 RLY S67 BRK1 BRK2 BRK1 FIL NF1 NF2 BRK1 S62 BRK1 S66 S69 S63 Motors Symbol M1 M2 M3 M4 M5 M6 M7 M8 M9 M10 M11 M12 M13 M14 M15 M16 M17 M18 M19 M20 M21 M22 M23 M24 M25 M26 M27 M28 M29 M30 M31 M32 M33 M34 M35 M36 M37 M38 M39 M40 M41 M42 Sensors and Switches Name SCAN-MOT Scan motor POL-MOT Polygonal motor FUS-MOT Fuser motor WEB-MOT Web motor TNR-MOT New toner supply motor TNR-TR-MOT New toner transport motor HOP-MOT Hopper motor RCY-TNR-MOT Recycle toner transport motor USD-TNR-MOT Used toner transport motor DEV-MOT Developer unit motor DRM-MOT Drum motor CH-CLN-MOT Wire cleaner drive motor DRM-CLN-MOT Cleaning brush drive motor TRB-MOT Transfer belt motor TRB-CAM-MOT Transfer belt cam motor RGST-MOT Registration motor MT-MOT Transport motor EXIT-MOT Exit motor REV-MOT Reverse motor FEED-MOT Feed motor CST-TRY-MOT1 Tray-up motor-1 CST-TRY-MOT2 Tray-up motor-2 * Only for JPD/NAD/SAD/DAU/DMJ model of all equipments and TWD model of e-STUDIO600/720 SLG-FAN-MOT SLG board cooling fan REV-FAN-MOT1 Reverse section cooling fan-1 REV-FAN-MOT2 Reverse section cooling fan-2 IH-FAN-MOT IH board cooling fan DCT-O-FAN-MOT Duct out fan FUS-FAN-MOT Fuser cooling fan EXIT-FAN-MOT Exit section cooling fan DCT-I-FAN-MOT Duct in fan DEV-FAN-MOT Developer unit fan LSU-FAN-MOT Laser unit cooling fan SYS-FAN-MOT SYS board cooling fan PS-FAN-MOT1 Switching regulator cooling fan-1 PS-FAN-MOT2 Switching regulator cooling fan-2 DF-READ-MOT Read motor DF-FEED-MOT Document feed motor DF-TRY-MOT Tray lift motor DF-L-EXIT-MOT Large original exit motor DF-S-EXIT-MOT Small original exit motor LCF-TRY-MOT Tandem LCF tray-up motor * Only for TNA/ASD/ASU/ARD/AUD/MJD/CND/KRD model of all equipments and TWD model of e-STUDIO850 LCF-ENDF-MOT Tandem LCF end fence motor * Only for TNA/ASD/ASU/ARD/AUD/MJD/CND/KRD model of all equipments and TWD model of e-STUDIO850 Figure 1)-a 1)-b 3)-a 3)-b Wire harness location Symbol 8-B S1-5 5-E S6 4) 7-D S7 4) 7-C S8 5) 5) 6) 5-B 5-B 6-B S9 S10 S11 6) 6-B S12 6) 7-C S13 7)-a 6-D S14 7)-a 6-E S15 7)-a 6-B S16 7)-a 7)-a 7)-a 6-D 6-E 6-F S17 S18 S19 8) 6-F S20 8) 8-B S21 9) 6-A S22 9) 7-G S23 13) 6-H S24 13) 7-A S25 S26 13) 7-B S27 1)-a 1)-b 2-E S28 9) 7-F S29 9) 7-F S30 10) 10) 10) 10) 7-E 7-C 6-D 7-C S31 S32 S33 S34 11) 6-D 11) 6-D S36 11) 6-D S37 15) 5-C S35 S38 15) 4-F S39 15) 4-F S40 17)-c 3-H 17)-c 3-H S41 S42 17)-c 3-G 17)-c 3-G S43 17)-c 3-G S44 14) 8-H S45 S46 14) 8-G S47 S48 Name APS1-3, APS-C, APS-R Automatic original detection sensor HOME-SNR Carriage home position sensor TEMP/HUMI-SNR Temperature/humidity sensor WEB-SNR Web detection sensor FUS-TR-SNR Fuser transport sensor TNR-EMP-SNR Toner cartridge empty detection sensor USD-TNR-FLL-SNR Toner bag full detection sensor ATTNR-SNR Auto-toner sensor DRUM-SUF-SNR Drum surface potential sensor TNR-LVL-SNR Image quality sensor TRB-SNR2 Transfer belt release detection sensor TRB-SNR1 Transfer belt contact detection sensor MID-TR-SNR Intermediate transport sensor RGST-SNR Registration sensor HRZ-TR-SNR1 Horizontal transport sensor-1 HRZ-TR-SNR2 Horizontal transport sensor-2 HRZ-TR-SNR3 Horizontal transport sensor-3 EXIT-SNR Exit sensor REV-SNR1 Reverse sensor-1 REV-SNR2 Reverse sensor-2 SFB-COV-SNR Bypass feed unit cover sensor FEED-COV-SNR Feed cover sensor SFB-FEED-SNR Bypass feed sensor SFB-SIZE-SNR Bypass paper size detection sensor CST1-SNR 1st drawer detection sensor CST1-BTM-SNR 1st drawer bottom sensor CST1-EMP-SNR 1st drawer empty sensor CST1-TRY-SNR 1st drawer tray-up sensor CST1-TR-SNR 1st drawer transport sensor CST1-FEED-SNR 1st drawer feed sensor CST2-SNR 2nd drawer detection sensor CST2-BTM-SNR 2nd drawer bottom sensor CST2-EMP-SNR 2nd drawer empty sensor CST2-TRY-SNR 2nd drawer tray-up sensor CST2-TR-SNR 2nd drawer transport sensor CST2-FEED-SNR 2nd drawer feed sensor CST3-SNR 3rd drawer detection sensor CST3-BTM-SNR 3rd drawer bottom sensor * Only for JPD/NAD/SAD/DAU/DMJ model of all equipments and TWD model of e-STUDIO600/720 CST3-EMP-SNR 3rd drawer / tandem LCF empty sensor CST3-TRY-SNR 3rd drawer / tandem LCF tray-up sensor CST3-TR-SNR 3rd drawer / tandem LCF transport sensor CST3-FEED-SNR 3rd drawer / tandem LCF feed sensor CST4-SNR 4th drawer detection sensor * Only for JPD/NAD/SAD/DAU/DMJ model of all equipments and TWD model of e-STUDIO600/720 CST4-BTM-SNR 4th drawer bottom sensor * Only for JPD/NAD/SAD/DAU/DMJ model of all equipments and TWD model of e-STUDIO600/720 Figure 1)-a 1)-b 1)-a 1)-b Wire harness location 2-E Symbol S49 2-F 2) 5-A 4) 7-C S50 S51 4) 5) 6-F 6-B 6-C 7)-a 6-F 7)-a 6-F 8) 8-B 6-E 7-E 8) 7-E 8) 7-E 9) 7-F 9) 7-F 9) 7-F 11) 5-A 11) 5-B S53 S54 S55 S56 S57 S58 S59 S60 S61 S62 S63 S64 S65 S66 S67 S68 * Only for JPD/NAD/SAD/DAU/DMJ model of all equipments and TWD model of e-STUDIO600/720 CST4-TR-SNR 4th drawer transport sensor DF-TRY-SNR Original tray sensor DF-TRY-VR-SNR Original tray width sensor DF-RGST-SNR Original registration sensor DF-SIZE-SNR1 Original width detection sensor-1 DF-SIZE-SNR2 Original width detection sensor-2 DF-SIZE-SNR3 Original width detection sensor-3 DF-U-LMT-SNR Lifting tray upper limit detection sensor DF-EMP-SNR Original empty sensor DF-COV-SNR Jam access cover sensor DF-L-LMT-SNR Lifting tray lower limit detection sensor DF-LENG-SNR Original length detection sensor DF-APS-SNR APS operation sensor DF-OPN-SNR RADF opening/closing sensor DF-SD-REV-SNR Small original reverse sensor DF-SD-EXIT-SNR Small original exit sensor DF-LD-EXIT-SNR Large original exit sensor DF-READ-SNR Read sensor DF-MID-TR-SNR Original intermediate transport sensor LCF-BTM-SNR Tandem LCF bottom sensor 12) 8-B 13) 8-C 13) 7-A 13) 8-C * Only for TNA/ASD/ASU/ARD/AUD/MJD/CND/KRD model of all equipments and TWD model of e-STUDIO850 8-C LCF-MST-SNR Standby side mis-stacking sensor 13) 13) 13) 13) S71 S72 8-C 8-C S73 8-D 13) 7-A 13) 8-D S74 S75 13) 8-D 13) 8-D SW1 13) 8-D SW2 13) 8-E SW3 SW4 13) 7-B SW5 13) 8-E SW6 13) 8-E SW7 13) 8-E SW8 13) 8-E SW9 13) 8-F SW10 SW11 13) 8-F 13) 8-F 13) 8-F Symbol CLT1 CLT3 CLT5 CLT6 * Only for JPD/NAD/SAD/DAU/DMJ model of all equipments and TWD model of e-STUDIO600/720 8-A S70 13) Electromagnetic spring clutches CLT4 12) S69 Wire harness location CLT2 CST4-TRY-SNR 4th drawer tray-up sensor 5-B 7)-a 8) * Only for JPD/NAD/SAD/DAU/DMJ model of all equipments and TWD model of e-STUDIO600/720 CST4-FEED-SNR 4th drawer feed sensor 5-A 8) CST4-EMP-SNR 4th drawer empty sensor 7-B 7)-a 7)-a Figure * Only for JPD/NAD/SAD/DAU/DMJ model of all equipments and TWD model of e-STUDIO600/720 S52 6) Name * Only for TNA/ASD/ASU/ARD/AUD/MJD/CND/KRD model of all equipments and TWD model of e-STUDIO850 LCF-ENDF-HP-SNR End fence home position sensor * Only for TNA/ASD/ASU/ARD/AUD/MJD/CND/KRD model of all equipments and TWD model of e-STUDIO850 LCF-EMP-SNR Standby side empty sensor * Only for TNA/ASD/ASU/ARD/AUD/MJD/CND/KRD model of all equipments and TWD model of e-STUDIO850 13) 8-F CLT7 17)-a 3-H 17)-a 3-H CLT8 CLT9 * Only for TNA/ASD/ASU/ARD/AUD/MJD/CND/KRD model of all equipments and TWD model of e-STUDIO850 FSR-SW Fuser detection switch TNR-SW Toner cartridge detection switch DEV-SW Developer unit detection switch CH-CLN-POS-SW Wire cleaner position detection switch EXIT-COV-SW Exit cover switch MAIN-SW Main switch U-FRNT-COV-SW Front cover switch COV-INTLCK-SW Cover interlock switch DF-OPN-INTLCK-SW RADF opening/closing switch DF-COV-INTLCK-SW Jam access cover opening/closing switch TNR-MOT-INTLCK-SW Toner motor interlock switch Name HRZ-DR-CLT1 Horizontal transport section driving clutch-1 HRZ-DR-CLT2 Horizontal transport section driving clutch-2 HRZ-DR-CLT3 Horizontal transport section driving clutch-3 SFB-FEED-CLT Bypass feed clutch CST1-TR-CLT 1st drawer transport clutch CST1-FEED-CLT 1st drawer feed clutch CST2-TR-CLT 2nd drawer transport clutch CST2-FEED-CLT 2nd drawer feed clutch CST3-TR-CLT 3rd drawer / tandem LCF transport clutch CST3-FEED-CLT 3rd drawer / tandem LCF feed clutch CST4-TR-CLT 4th drawer transport clutch 17)-a 3-G 17)-a 3-G 17)-a 3-G * Only for JPD/NAD/SAD/DAU/DMJ model of all equipments and TWD model of e-STUDIO600/720 17)-a 3-G CST4-FEED-CLT 4th drawer feed clutch 17)-b 3-G 17)-b 3-G Solenoids 17)-b 3-G Symbol 17)-b 4-F SOL1 17)-b 4-F SOL2 17)-c 2-H 17)-c 2-G 17)-d 4-G 17)-d 4-G 17)-d 2-H 17)-d 2-G 17)-d 4-G 14) 8-G CLT10 CLT11 CLT12 SOL3 SOL4 SOL5 SOL6 SOL7 SOL8 * Only for JPD/NAD/SAD/DAU/DMJ model of all equipments and TWD model of e-STUDIO600/720 Name SPRT-FING-SOL Drum separation finger solenoid GATE-SOL Gate solenoid SFB-SOL Bypass pickup solenoid DF-SD-SOL Small original exit solenoid DF-LD-SOL Large original exit solenoid DENG-SOL Large original exit roller release solenoid LCF-PICK-SOL Tandem LCF pickup solenoid * Only for TNA/ASD/ASU/ARD/AUD/MJD/CND/KRD model of all equipments and TWD model of e-STUDIO850 LCF-ENDF-SOL Tandem LCF end fence solenoid * Only for TNA/ASD/ASU/ARD/AUD/MJD/CND/KRD model of all equipments and TWD model of e-STUDIO850 Wire harness location Symbol 8) 7-E EXP 8) 7-E ERS 8) 7-E IH-COIL 12) 8-B DH1 13) 8-C DH2 13) 8-C DH3 13) 8-D 13) 8-D Symbol 13) 8-E THM1 13) 8-E THM2 13) 8-F 14) 8-G CCD SLG 14) 8-G DSP KEY1 14) 8-G KEY2 14) 8-G 4) AC wire harness 5) 5-B 7)-a 6-B 7)-a 6-C LDR1 LDR2 SNS FUS 8-F THM5 THMO1 Figure Wire harness location 7)-a 6-C 9) 7-F 12) 8-A 17)-c 2-G 17)-c 2-G 17)-c 2-G 13) 8-E THMO2 THMO3 THMO4 14) 8-H Name PWA-F-CCD CCD driving PC board (CCD board) PWA-F-SLG Scanning section control PC board (SLG board) PWA-F-DSP Display PC board (DSP board) PWA-F-KEY1 Key PC board-1 (KEY1 board) PWA-F-KEY2 Key PC board-2 (KEY2 board) PWA-F-PLG Laser control PC board (PLG board) PWA-F-LDR1 Laser driving PC board-1 (LDR1 board) PWA-F-LDR2 Laser driving PC board-2 (LDR2 board) * Only for e-STUDIO850/853 models PWA-F-SNS H-sync detection PC board (SNS board) PWA-F-FUS Fuse PC board (FUS board) * Optional for TNA/NAD/MJD/DMJ model, standard for other mod- Figure 1)-a 1)-b 1)-a 1)-b 2) 9) 7-F IH 10) 6-B AC wire harness MOT 10) 5-B MOT2-MT 10) AC wire harness MOT2-RV 17)-c 2-G SYS 17)-c 2-G LGC 10) 5-B FIL PWA-F-IH Heater control PC board (IH board) PWA-F-MOT Motor driving PC board (MOT board) PWA-F-MOT2-MT Transport motor driving PC board (MOT2-MT board) PWA-F-MOT2-RV Reverse motor driving PC board (MOT2-RV board) PWA-F-SYS System control PC board (SYS board) PWA-F-LGC Logic PC board (LGC board) PWA-F-FIL Filter PC board (FIL board) * Only for TNA/NAD/SAD model of all equipments and TWD model HVT PWA-F-ADF RADF control PC board (ADF board) Wire harness location 1)-a 1)-b 2-D 7)-a 6-C 4) AC wire harness 1)-c AC wire harness 1)-c AC wire harness 7)-b AC wire harness Figure Wire harness location THMS-F-HTR Fuser roller front thermistor THMS-C-HTR Fuser roller center thermistor THMS-R-HTR Fuser roller rear thermistor THMS-L-HTR Pressure roller thermistor THMS-DRM Drum thermistor THERMO-C-HTR Fuser roller center thermostat THERMO-S-HTR Fuser roller side thermostat THERMO-SCN-DH Scanner damp heater thermostat THERMO-DRM-DH Drum damp heater thermostat 4) 7-B 4) 7-B 4) 7-B 4) 7-C 7)-a 6-C 4) AC wire harness 4) AC wire harness 1)-c AC wire harness 7)-b AC wire harness Name Figure Wire harness location PS-HVT High-voltage transformer 15) 6-G Figure Wire harness location 1)-a 1)-b 2-D 2) 3-B 2) 3-B 2) 3-A 3)-b 5-G Others Symbol LCD INV-LCD 3-E GLV Name INV-EXP Lamp inverter board LCD LCD panel TCP Touch panel INV-LCD LCD inverter board MIR-GLV Galvanic mirror * Only for e-STUDIO850/853 3-F 4-A 4-A 2) 3-A HDD PS NF1 5-E NF2 3)-b 4-F 3)-a 3)-b 5-E 5-F HDD Hard disk PS-ACC Switching regulator NS-FIL1 Noise filter-1 NS-FIL2 Noise filter-2 15) 4-C 15) 5-G AC wire harness 16)-a 16)-b 16)-c 16)-d AC wire harness 16)-b AC wire harness 16)-a 16)-b 16)-c 16)-d AC wire harness 16)-b AC wire harness 16)-b AC wire harness * Only forJPD model of e-STUDIO850 4-E BRK1 BRK2 BREAKER1 Breaker-1 BREAKER2 Breaker-2 * Only for JPD model of e-STUDIO850 7)-b AC wire harness RLY RELEY Relay * Only for JPD model of e-STUDIO850 10) 7-D 15) 6-E 11) 8-B 9) 7-G 15) 3-B 15) 6-A 16)-c AC wire harness 17)-c 3-F of e-STUDIO600/720 ADF Name Symbol Wire harness location 2) 3)-a 3)-b 3)-a 3)-b LP-EXPO Exposure lamp LP-ERS Discharge LED IH-COIL IH coil SCN-DH-L Scanner damp heater (Left) SCN-DH-R Scanner damp heater (Right) DRM-DH Drum damp heater Figure Transformer INV-EXP els 7-B 07/11 THM3 THM4 13) Name Thermistors and thermostats TCP Symbol S70 Lamps and heaters Figure PC boards PLG LCF-ENDF-STP-SNR End fence stop position sensor S68 [...]... e-STUDIO520/600/720 only e-STUDIO520/523/600/603/720/723/850/853 SPECIFICATIONS/ACCESSORIES/OPTIONS/SUPPLIES © 2005 - 2007 TOSHIBA TEC CORPORATION All rights reserved 1-8 • Dimensions of the equipment See the figure below (W 698 x D 789 x H 1213 (mm)) 1 1213 m m 698 m m 789 mm Fig 1-1 © 2005 - 2007 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO520/523/600/603/720/723/850/853 SPECIFICATIONS/ACCESSORIES/OPTIONS/SUPPLIES... PS-ZT7200E (for MJD, DMJ) PS-TB6510E (for MJD, DMJ) PS-TB6510 (for other) e-STUDIO520/523/600/603/720/723/850/853 SPECIFICATIONS/ACCESSORIES/OPTIONS/SUPPLIES © 2005 - 2007 TOSHIBA TEC CORPORATION All rights reserved 1 - 12 07/11 © 2005 - 2007 TOSHIBA TEC CORPORATION All rights reserved 1 - 13 07/11 Staple cartridge STAPLE-1700 STAPLE-1800 STAPLE-1900 Staple cartridge STAPLE-600 Finisher guide rail KN-1017... lower limit detection sensor Ch.5.1.1 © 2005 - 2007 TOSHIBA TEC CORPORATION All rights reserved Ch.5.1.1 2 Ch.5.1.1 Ch.5.1.1 Ch.5.1.1 Ch.5.1.1 Ch.5.1.1 Ch.5.1.1 Ch.5.1.1 Ch.5.1.4 Ch.5.1.4 Ch.5.1.4 Ch.5.1.4 Ch.5.1.4 Ch.5.1.4 e-STUDIO520/523/600/603/720/723/850/853 ERROR CODE AND SELF-DIAGNOSTIC MODE 2-5 Error code E721 Classification RADF jam E722 E723 E724 E725 E726 E728 E731 E732 E733 E741 E742 E743... 32 28 34 30 34 30 38 34 28 28 30 30 30 30 34 34 28 28 30 30 30 30 34 34 Tolerance: Within -0.5 from +1 e-STUDIO520/523/600/603/720/723/850/853 SPECIFICATIONS/ACCESSORIES/OPTIONS/SUPPLIES © 2005 - 2007 TOSHIBA TEC CORPORATION All rights reserved 1-4 07/11 Thick 2 (Paper weight: From over 105 g/m² (28 lb Bond) to 163 g/m² (90 lb Index)) Paper source: Drawers / Tandem LCF / Option LCF A4, B5, A5-R, LT,... 46 30 50 34 37 28 38 30 38 30 42 34 37 28 38 30 38 30 42 34 32 28 34 30 34 30 38 34 32 28 34 30 34 30 38 34 28 28 30 30 30 30 34 34 28 28 30 30 30 30 34 34 Tolerance: Within -0.5 from +1 © 2005 - 2007 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO520/523/600/603/720/723/850/853 SPECIFICATIONS/ACCESSORIES/OPTIONS/SUPPLIES 1-5 07/11 1 Thick 3 (Paper weight: From over 163 g/m² (90 lb Bond) to 209... 32 28 34 30 34 30 34 30 28 28 30 30 30 30 30 30 28 28 30 30 30 30 30 30 Tolerance: Within -0.5 from +1 e-STUDIO520/523/600/603/720/723/850/853 SPECIFICATIONS/ACCESSORIES/OPTIONS/SUPPLIES © 2005 - 2007 TOSHIBA TEC CORPORATION All rights reserved 1-6 07/11 • System copy speed Sec Copy mode Single-sided originals ↓ Single-sided copies Single-sided originals ↓ Double-sided copies Double-sided originals... sizes can be set.) 64 to 209g/m² ( 17 lb Bond to 115.7 lb Index) Tracing paper (75g/m² only), Tab paper Labels, OHP film, Tab paper, (2nd drawer is recommended) Remarks These special papers recommended by Toshiba Tec • First copy time e-STUDIO520/523/600/603/720/723: Approx 4.0 sec or less e-STUDIO850/853: Approx 3.5 sec or less (A4/LT, 1st drawer, 100%, original placed manually, Top side discharge) •... 100±0.5% Zooming: 25 to 400% in increments of 1% (25 to 200% when using RADF) • Resolution/Gradation Scanning: 600 dpi x 600 dpi Printing: Equivalent to 2400 dpi x 600 dpi Gradation: 256 steps © 2005 - 2007 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO520/523/600/603/720/723/850/853 SPECIFICATIONS/ACCESSORIES/OPTIONS/SUPPLIES 1-7 07/11 1 • Eliminated portion Leading edges: 3.0±2.0 mm, Side/trailing... LCF Tandem LCF Tandem LCF Tandem LCF: This means 2 drawers and a tandem LCF In this manual, a standard LCF is called the Tandem LCF (T-LCF), and MP-4004A/L is called the Option LCF (O-LCF) © 2005 - 2007 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO520/523/600/603/720/723/850/853 SPECIFICATIONS/ACCESSORIES/OPTIONS/SUPPLIES 1-1 07/11 • Accepted originals Sheet, book and 3-dimensional object The... ASU, MJD, KRD) 1 pc (for ASU, MJD, DMJ, KRD) 1 pc (for CND) 1 pc (for CND) 1 pc (for CND) 2 pc (for MJD) e-STUDIO520/523/600/603/720/723/850/853 SPECIFICATIONS/ACCESSORIES/OPTIONS/SUPPLIES © 2005 - 2007 TOSHIBA TEC CORPORATION All rights reserved 1 - 10 06/09 1.3 Options Large Capacity Feeder (LCF) Finisher Saddle stitch finisher Saddle stitch finisher (100 sheets stapling) Staple cartridge Finisher guide