SHIRT tech pack

SEASON: AW’ 07 PRODUCT PACK - DRESS SHIRTS PRODUCT: STYLE NO FABRIC Department REGULAR COLLAR WITH ROUND CUFF RAY 001 100 % COTTON FABRICS 100% LINEN FABRICS Approved by: Signature CONTENTS PRODUCT DETAILS STYLE LINES BLOCK DETAILS, SPEC SHEET & MEASUREMENT GUIDELINE CONSTRUCTION DETAILS BUTTON PLACEMENTS LABEL PLACEMENTS FOLDING & PACKING TRIM LIST Date: Product Sourcing Quality N.B.: Any amendment should be in consultation/agreement between all the departments mentioned above Any queries regarding the product pack can be marked to product department on the following address: Style lab,Raymond Apparel Ltd., Jekegram, Pokhran Road no.1, Thane-400606 , Mahrashtra, India Ph: 25988050,25988015 STYLE LAB RAYMOND APPAREL LIMITED Jekegram Thane 4-8 10 11 12 RAY 001 STYLE LINE LONG SLEEVES DRESS SHIRT WITH REGULAR COLLAR ROUND CUFF 42 Garment style lines: Double fused Regular collar with Removable collar stays Round corner Pocket , Convertible Barrel cuffs, fused cut & sew center placket SPI 18 for all top stitches Thread: 150tkt PPC spun Body & Button Hole thread to be DTM to basie fabric Button & main label threads to be DTM to button & main label respectively Buttons : 16L & 14L, hole DTM Buttons ( P0428/P695., P0839/P6957) For DTM & Button Type refer to trim card THREAD: 95m For Branding Embroidery thread to be Madeira Poly neon / Calypso: Mrts INTERLINING: 25cm (90cm width) Collar Skin, Band & Cuff - DHJ 285 ES Consumption : 17cm., Collar Patch & Placket - DHJ Polystar 2.28.23.464 ES Consumption : 8cm STYLE LAB RAYMOND APPAREL LIMITED Jekegram Thane STYLE LINE RAY 001 2.1 SHORT SLEEVES DRESS SHIRT WITH REGULAR COLLAR ROUND CUFF 42 Garment style lines: Double fused Regular collar with Removable collar stays Round corner Pocket , fused cut & sew center placket SPI 18 for all top stitches Thread: 150tkt PPC spun Body & Button Hole thread to be DTM to basic fabric Button & main label threads to be DTM to button & main label respectively Buttons : 16L & 14L, hole DTM Buttons ( P0428/P695., P0839/P6957) For DTM & Button Type refer to trim card THREAD: 75m For Branding Embroidery thread to be Madeira Poly neon / Calypso: Mrts INTERLINING: 20cm (90cm width) Collar Skin, Band & Cuff - DHJ 285 ES Consumption : 12cm Collar Patch & Placket - DHJ Polystar 2.28.23.464 ES Consumption : 8cm STYLE LAB RAYMOND APPAREL LIMITED Jekegram Thane BLOCK DETAILS, SPEC SHEET & MEASUREMENTS GUIDE LINES RAY 001 BLOCK DETAILS: Body: Raymond ; Collar: C-01 RY REGULAR; C-band: CB-01 RY Pocket: PK-01 RY Cuff: CF 00 RY SPEC SHEET Code MESUREMENT GUIDELINE Description Size 39 39.50 40 40.50 42 42.50 44 44.50 46 46.50 0.50 Collar Height at CB 4.50 4.50 4.50 4.50 4.50 0.00 Collarband height at CB 3.50 3.50 3.50 3.50 3.50 0.00 Collar point 7.50 7.50 7.50 7.50 7.50 0.00 tie space 0.50 0.50 0.50 0.50 0.50 0.20 Collar bottom measurement 39.00 40.00 42.00 44.00 46.00 0.30 Collar band bottom measurement 43.70 44.70 46.70 48.70 50.70 0.30 Collar button to buttonhole Tol (+/-) Collar spread 10.50 10.50 10.50 10.50 10.50 0.70 1/2 Chest 58.50 60.00 63.00 66.00 69.00 1.00 10 1/2 Waist 55.50 57.00 60.00 63.00 66.00 1.00 11 1/2 Bottom 56.50 58.00 61.00 64.00 67.00 1.00 12 CB length 79.50 80.00 81.00 82.00 83.00 1.00 13 CF length band dow n 69.90 70.30 71.10 71.90 72.70 1.00 14 Yoke height at CB 11.50 11.50 11.50 11.50 11.50 0.30 15 Back Shoulder Length 47.25 48.00 49.50 51.00 52.50 0.50 16 1/2 Armhole Curve 26.50 27.00 28.00 29.00 30.00 0.50 17 Long Sleeve Length From C.B.N 87.38 88.00 89.25 90.50 90.75 1.00 18 Sleeve Length from shoulder 63.75 64.00 64.50 65.00 64.50 1.00 19 Cuff length 24.50 25.00 26.00 27.00 28.00 0.50 20 cuff height 7.00 7.00 7.00 7.00 7.00 0.00 21 1/2 Cuff Length Closed 11.00 11.25 11.75 12.25 12.75 0.30 22 Pocket from shoulder seam 21.50 22.00 22.00 22.50 22.50 0.50 23 Pocket from CF 4.50 5.00 5.00 5.50 5.50 0.50 NOTE: Chest (at armhole), waist, & bottom measurements are with seam pressed back, from edge to edge as shown in fig alongside Collar btn to btnhole measurement is from inside of buttonhole bar to centre of button 22 23 19 20 15 14 17 16 20 cm 18 12 13 10 11 All measurements are in centimetres 21 RAY 001 3.1 BLOCK DETAILS, SPEC SHEET & MEASUREMENT GUIDELINE BLOCK DETAILS: Body: Raymond ; Collar: C-01 RY REGULAR; C-band: CB-01 RY Pocket: PK-01RY MESUREMENT GUIDELINE SPEC SHEET Cod e Description Size 39 39.50 40 40.50 42 42.50 44 44.50 46 46.50 Tol (+/-) Collar button to buttonhole Collar Height at CB 4.50 4.50 4.50 4.50 4.50 0.00 Collarband height at CB 3.50 3.50 3.50 3.50 3.50 0.00 Collar point 7.50 7.50 7.50 7.50 7.50 0.00 tie space 0.50 0.50 0.50 0.50 0.50 0.20 Collar bottom measurement 39.00 40.00 42.00 44.00 46.00 0.30 Collar band bottom measurement 43.70 44.70 46.70 48.70 50.70 0.30 Collar spread 10.50 10.50 10.50 10.50 10.50 0.70 1/2 Chest 58.50 60.00 63.00 66.00 69.00 1.00 10 1/2 Waist 56.50 57.00 60.00 63.00 66.00 1.00 11 1/2 Bottom 56.50 58.00 61.00 64.00 67.00 1.00 12 CB length 79.50 80.00 81.00 82.00 83.00 1.00 13 CF length band dow n 69.90 70.30 71.10 71.90 72.70 1.00 14 Yoke height at CB 11.50 11.50 11.50 11.50 11.50 0.30 15 Back Shoulder Length 47.25 48.00 49.50 51.00 52.50 0.50 16 1/2 Armhole Curve 26.50 27.00 28.00 29.00 30.00 0.50 17 Sleeve Opening Round 37.00 38.00 40.00 42.00 44.00 0.50 18 Sleeve Length from shoulder 23.50 24.00 25.00 26.00 27.00 1.00 19 Sleeve Length from CBN 47.13 48.00 49.75 51.50 53.25 0.50 20 Pocket from shoulder seam 21.50 22.00 22.00 22.50 22.50 0.50 21 Pocket from CF 4.50 5.00 5.00 5.50 5.50 0.50 0.50 NOTE: Chest (at armhole), waist, & bottom measurements are with pressed back, from edge to edge as shown in fig alongside Collar btn to btnhole measurement is from inside of buttonhole bar to centre of button 20 21 15 19 16 18 17 20 cm 13 10 11 All measurements are in centimetres 14 12 CONSTRUCTION DETAILS - COLLAR & COLLAR BAND FABRIC SKIN PATCH RAY 001 COLLAR - C 01 RY 3mm fabric allowance 6mm 8.1 cm trimmed Collar point 7.5cm finished Collar point 1.5mm runstitch 5mm breakline 6mm  6mm trim allowance INTERLINING CUTTING DETAILS COLLAR SKIN - cut on true bias 45 degree COLLAR PATCH - cut on grain COLLAR BAND - cut on true bias 45 degree CUFF - cut on grain CENTRE PLACKET - cut on grain 2.5 cm leg 3mm fabric allowance BREAK LINE FINISH LINE TRIM LINE COLLARBAND - CB 01RY 1cm 6mm FINISH LINE CONSTRUCTION DETAILS - COLLAR & COLLAR BAND RAY 001 COLLAR - C 01 RY mm 1mm COLLARBAND - CB 01 RY Top stitch band & lock here Begin ‘finish collar’ here & end on same point on the other side Back tack ends mm 1mm 2.5”x3/8”x0.35mm Branded Nylon collar Stays CONSTRUCTION DETAILS - CUFF RAY 001 1.5cm fabric allowance FABRIC SKIN CUFF - CF-00 RY 6mm 1.5mm runstitch 4mm fabric allowance 1mm cuff attach 1cm Lock here, towards the button side of cuff mm stitch 3mm CONSTRUCTION DETAILS - POCKET, FRONTS & BACK 6mm RAY 001 L & R FRONTS 2.5 cm mm 1mm POCKET - PK 01 RY 14 cm 2.5cm mm 3.5cm 13 cm 3.5cm 1cm full roled hem For Both L/S & mm 1mm 4-5 stitches backtack cm YOKE & BACK cm NO PLEAT AT BACK 3.5cm cm CONSTRUCTION DETAILS - SLEEVE & SLEEVE PLACKET RAY 001 1.25 cm ATTACH SLEEVE TO BODY UPPER & UNDER SLEEVE PLACKET 2.5 cm Body Start here with stitches to lock 16.5 cm cm Hem Detail For S/S Shirt 2.3cm 1.25 cm SNCS Sleeve 1mm 1.25 cm 1.0 cm TOPSTITCH SLEEVE Body 2.5 cm hem height 1.0 cm 1mm 2.5 cm 1.0 cm 5mm or 3/16” gauge SIDE SEAM SNCS Sleeve SNCS Side seam: Feed of the arm, front over back on both sides DNCS BUTTON PLACEMENTS RAY 001 FOR BUTTON TYPE & LIGNE REFER TO TRIM CARD BUTTON PLACEMENTS Collar btn to be in line withbtns on placket Adjust slightly to maintain vertical line balancing in plaid & striped fabrics 6.5 cm 9.0 cm 9.0 cm cm 1.75 cm Spare buttons 1.5 cm 7.5 cm Last button hole is horizontal All button holes to have Purl stitch formation 1.75 cm 1.75 cm All btns to be sewn with cross lock stitch Button sew thread to be dtm to button Provide adequate stemming to buttons 16L buttons + 14L buttons 2+1 NOTE: Sew 16L Buttons with laser Branding on wearer’s Right cuff 1.45 cm to outer edge of Button hole bar 6.3 cm 6.3 cm 2.5 cm 4.5 cm 1.0 cm to outer edge of Button hole bar LABEL PLACEMENTS RAY 001 10 40cm 4.5 cm 3.5 cm 3.5cms, centered at CB to center of the embroidery & Thread as for the DTM ( Thread to be used Poly neon) Wash Care label to be inserted Left Wearer side inside the Feed of the arm Egyptian Giza Cotton Only for 100% Cotton Fabrics Wash care 10 cm 1.5 cm FOLDING & PACKGING RAY 001 11 Insert 1-Pearl head 2-Metal cross clip to hold pin and 1-White tail ( one end inserted in Plastic “M-clip” to hole of back support) hold sleeves inside FOR TAGS REFER TO TRIM CARDS Raymond Back Supporter 42 TUCK IN TAIL (Tail to be laid flat inside) Pearl-head pins to be inserted from the top of the back support Ba co r ta de g 1-Metal cross clip to hold cuff, to be placed beneath sleeve placket & cuff 36cm (+/-0.3) r olla e re c p Spa envelo stay g g Ta Han NOT TO BE VISIBLE EITHER ON FRONT OR BACK Two long printed tissue paper BOPP Poly bag to be used Hang tag to be put on 1st button hole ( excluding neck button) Using Branded locking loop Bar Code Tag & Spare Collar Stay Envelope on last but one button 23 cm (+/-0.3) Cuff to be aligned with bottom of board COLLAR SIZE TAB TO BE STUCKED IN THE CENTER OF THE COLLAR PVC band dented side towards CF Branded collar Strip to be inserted under PVC band Cardboard neckband, longer edge up Blend label 40 40 Note: Metal clips -made of rust proof non corrosive metal with smooth edges Metal pins -made of rust proof non corrosive with plastic silver head 042 R BUTTERFLY Bottom edge of band to be aligned after pinning 1-silver plastic head pin at neck band, tuck in-out-in with~1.5cm bite outside FOLDING & PACKGING RAY 001 11.1 Insert 1-Pearl head 2-Metal cross clip to hold pin and 1-White tail ( one end inserted in Plastic “M-clip” to hole of back support) hold sleeves inside FOR TAGS REFER TO TRIM CARDS Raymond Back Supporter 42 TUCK IN TAIL (Tail to be laid flat inside) Ba co r ta de g Pearl-head pins to be inserted from the top of the back support 36cm (+/-0.3) NOT TO BE VISIBLE ON BACK r olla e re c p Spa envelo stay g g Ta Han 1-Metal cross clip to hold sleeve Hang tag to be put on 1st button hole ( excluding neck button) Using Branded locking loop Two long printed tissue paper BOPP Poly bag to be used Bar Code Tag & Spare Collar Stay Envelope on last but one button 23 cm (+/-0.3) Cuff to be aligned with bottom of board COLLAR SIZE TAB TO BE STUCKED IN THE CENTER OF THE COLLAR PVC band dented side towards CF Branded collar Strip to be inserted under PVC band Cardboard neckband, longer edge up Blend label 40 40 Note: Metal clips -made of rust proof non corrosive metal with smooth edges Metal pins -made of rust proof non corrosive with plastic silver head 042 R BUTTERFLY Bottom edge of band to be aligned after pinning 1-silver plastic head pin at neck band, tuck in-out-in with~1.5cm bite outside [...]... for the DTM ( Thread to be used Poly neon) Wash Care label to be inserted Left Wearer side inside the Feed of the arm Egyptian Giza Cotton Only for 100% Cotton Fabrics Wash care 10 cm 1.5 cm FOLDING & PACKGING RAY 001 11 Insert 1-Pearl head 2-Metal cross clip to hold pin and 1-White tail ( one end inserted in Plastic “M-clip” to hole of back support) hold sleeves inside FOR TAGS REFER TO TRIM CARDS... rust proof non corrosive with plastic silver head 042 R BUTTERFLY Bottom edge of band to be aligned after pinning 1-silver plastic head pin at neck band, tuck in-out-in with~1.5cm bite outside FOLDING & PACKGING RAY 001 11.1 Insert 1-Pearl head 2-Metal cross clip to hold pin and 1-White tail ( one end inserted in Plastic “M-clip” to hole of back support) hold sleeves inside FOR TAGS REFER TO TRIM CARDS ...RAY 001 STYLE LINE LONG SLEEVES DRESS SHIRT WITH REGULAR COLLAR ROUND CUFF 42 Garment style lines: Double fused Regular collar with Removable... 8cm STYLE LAB RAYMOND APPAREL LIMITED Jekegram Thane STYLE LINE RAY 001 2.1 SHORT SLEEVES DRESS SHIRT WITH REGULAR COLLAR ROUND CUFF 42 Garment style lines: Double fused Regular collar with Removable... UNDER SLEEVE PLACKET 2.5 cm Body Start here with stitches to lock 16.5 cm cm Hem Detail For S/S Shirt 2.3cm 1.25 cm SNCS Sleeve 1mm 1.25 cm 1.0 cm TOPSTITCH SLEEVE Body 2.5 cm hem height 1.0 cm