Tài liệu hướng dẫn sửa chữa xe Nissan pathfinder r52 esm tai lieu sua chua phan 7 . Cung cấp các thông tin cần thiết cho Kỹ thuật viên tiến hành chẩn đoán, sửa chữa nhanh chóng, chính xác, hiệu quả, hợp lý
DRIVER INFORMATION & MULTIMEDIA SECTION WCS WARNING CHIME SYSTEM A B C D E CONTENTS PRECAUTION DIAGNOSIS SYSTEM (BCM) 14 PRECAUTIONS COMMON ITEM 14 COMMON ITEM : CONSULT Function (BCM COMMON ITEM) .14 Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" SYSTEM DESCRIPTION BUZZER .14 BUZZER : CONSULT Function (BCM - BUZZER) 15 COMPONENT PARTS ECU DIAGNOSIS INFORMATION 16 Component Parts Location Component Description BCM, COMBINATION METER 16 SYSTEM WARNING CHIME SYSTEM WARNING CHIME SYSTEM : System Diagram WARNING CHIME SYSTEM : System Description LIGHT REMINDER WARNING CHIME LIGHT REMINDER WARNING CHIME : System Diagram LIGHT REMINDER WARNING CHIME : System Description SEAT BELT WARNING CHIME SEAT BELT WARNING CHIME : System Diagram SEAT BELT WARNING CHIME : System Description PARKING BRAKE RELEASE WARNING CHIME PARKING BRAKE RELEASE WARNING CHIME : System Diagram PARKING BRAKE RELEASE WARNING CHIME : System Description DIAGNOSIS SYSTEM (COMBINATION METER) Description CONSULT Function (METER/M&A) Revision: October 2012 F G H I List of ECU Reference .16 WIRING DIAGRAM 17 J WARNING CHIME SYSTEM 17 Wiring Diagram 17 K BASIC INSPECTION 25 DIAGNOSIS AND REPAIR WORKFLOW 25 Work Flow 25 L DTC/CIRCUIT DIAGNOSIS 27 POWER SUPPLY AND GROUND CIRCUIT 27 M COMBINATION METER 27 COMBINATION METER : Diagnosis Procedure 27 WCS BCM (BODY CONTROL MODULE) 27 BCM (BODY CONTROL MODULE) : Diagnosis Procedure 28 O METER BUZZER CIRCUIT 29 Description .29 Component Function Check 29 Diagnosis Procedure 29 SEAT BELT BUCKLE SWITCH SIGNAL CIRCUIT 30 Description .30 Component Function Check 30 WCS-1 2013 Pathfinder NAM P Diagnosis Procedure 30 Component Inspection 31 THE SEAT BELT WARNING CONTINUES SOUNDING, OR DOES NOT SOUND 34 SYMPTOM DIAGNOSIS 32 Description 34 Diagnosis Procedure 34 WARNING CHIME SYSTEM SYMPTOMS 32 Symptom Table 32 THE LIGHT REMINDER WARNING DOES NOT SOUND 33 Description 33 Diagnosis Procedure 33 Revision: October 2012 THE PARKING BRAKE RELEASE WARNING CONTINUES SOUNDING, OR DOES NOT SOUND 35 Description 35 Diagnosis Procedure 35 WCS-2 2013 Pathfinder NAM PRECAUTIONS < PRECAUTION > PRECAUTION A PRECAUTIONS Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" B INFOID:0000000008945485 The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collision Information necessary to service the system safely is included in the SR and SB section of this Service Manual WARNING: • To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in the event of a collision which would result in air bag inflation, all maintenance must be performed by an authorized NISSAN/INFINITI dealer • Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system For removal of Spiral Cable and Air Bag Module, see the SR section • Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness connectors PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS WARNING: • When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a hammer Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing serious injury • When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the battery and wait at least minutes before performing any service C D E F G H I J K L M WCS O P Revision: October 2012 WCS-3 2013 Pathfinder NAM COMPONENT PARTS < SYSTEM DESCRIPTION > SYSTEM DESCRIPTION COMPONENT PARTS Component Parts Location INFOID:0000000008509979 AWNIA2728ZZ Combination switch (lighting and turn signal switch) Combination meter Seat belt buckle switch (driver seat) Front door switch LH BCM (view with combination meter removed) Parking brake switch ABS actuator and electric unit (control unit) Revision: October 2012 WCS-4 2013 Pathfinder NAM COMPONENT PARTS < SYSTEM DESCRIPTION > Component Description INFOID:0000000008509980 A Unit Description B Combination switch (lighting and turn signal switch) Transmits the lighting switch signal to the BCM Combination meter • Receives a buzzer output signal from the BCM with CAN communication line and sounds the buzzer • Receives the seat belt buckle switch signal from the seat belt buckle switch (driver seat) and transmits it to the BCM via CAN communication • Judges whether the parking brake is released using the vehicle speed signal and the parking brake switch signal, and sounds the buzzer if necessary BCM Based on the signals received from various units and switches, transmits the buzzer output signal to the combination meter via CAN communication Front door switch LH Transmits the front door switch LH signal to the BCM Seat belt buckle switch (driver seat) Transmits the seat belt buckle switch (driver seat) signal to the combination meter Parking brake switch Transmits the parking brake switch signal to the combination meter ABS actuator and electric unit (control unit) Transmits the vehicle speed signal to the combination meter via CAN communication C D E F G H I J K L M WCS O P Revision: October 2012 WCS-5 2013 Pathfinder NAM SYSTEM < SYSTEM DESCRIPTION > SYSTEM WARNING CHIME SYSTEM WARNING CHIME SYSTEM : System Diagram INFOID:0000000008509981 AWNIA2541GB WARNING CHIME SYSTEM : System Description INFOID:0000000008509982 DESCRIPTION • The buzzer for the warning chime system is installed in the combination meter • The buzzer sounds when the combination meter receives a buzzer output signal from the BCM • The BCM receives signals from various units and transmits a buzzer output signal to the combination meter with CAN communication line if it judges that the warning buzzer should be activated LIGHT REMINDER WARNING CHIME LIGHT REMINDER WARNING CHIME : System Diagram INFOID:0000000008509983 AWNIA2539GB LIGHT REMINDER WARNING CHIME : System Description INFOID:0000000008509984 DESCRIPTION With the ignition switch in the OFF or ACC position, driver door open, and lighting switch in parking or headlamp position, the light warning chime will sound • BCM detects the ignition switch in the OFF or ACC position, the front door switch LH ON, and the lighting switch in parking or headlamp position, and then transmits the buzzer output signal (light reminder warning chime) to the combination meter with CAN communication line • When the combination meter receives the buzzer output signal (light reminder warning chime), it sounds the buzzer WARNING OPERATION CONDITIONS If all of the following conditions are fulfilled: • Lighting switch is in parking or headlamp position • Ignition switch is in OFF or ACC • Front door switch LH is ON Revision: October 2012 WCS-6 2013 Pathfinder NAM SYSTEM < SYSTEM DESCRIPTION > WARNING CANCEL CONDITIONS A Warning is canceled if any of the following conditions is fulfilled: • Lighting switch OFF • Ignition switch ON • Front door switch LH is OFF B SEAT BELT WARNING CHIME SEAT BELT WARNING CHIME : System Diagram INFOID:0000000008509985 C D E AWNIA2542GB SEAT BELT WARNING CHIME : System Description F INFOID:0000000008509986 G DESCRIPTION With the ignition switch turned ON and driver seat belt unfastened, the seat belt warning chime will sound for approximately seconds • BCM receives seat belt buckle switch (driver seat) signal from combination meter with CAN communication line • BCM detects the ignition switch turned ON and the seat belt buckle switch (driver seat) is ON, and then transmits buzzer output signal (seat belt warning chime) to combination meter with CAN communication line • When the combination meter receives the buzzer output signal (seat belt warning chime), it sounds the buzzer H I J WARNING OPERATION CONDITIONS If all of the following conditions are fulfilled: • Ignition switch OFF→ON • Seat belt buckle switch (driver seat) is ON (seat belt not fastened) K WARNING CANCEL CONDITIONS L Cancels the warning if any of the following conditions is fulfilled: • Ignition switch OFF • Seat belt buckle switch (driver seat) is OFF (seat belt fastened) M PARKING BRAKE RELEASE WARNING CHIME PARKING BRAKE RELEASE WARNING CHIME : System Diagram INFOID:0000000008509987 WCS O P AWNIA2578GB PARKING BRAKE RELEASE WARNING CHIME : System Description INFOID:0000000008509988 DESCRIPTION Revision: October 2012 WCS-7 2013 Pathfinder NAM SYSTEM < SYSTEM DESCRIPTION > • The combination meter receives the vehicle speed signal from the ABS actuator and electric unit (control unit) via CAN communication line • The combination meter judges whether the parking brake is released using the parking brake switch signal from the parking brake switch, and sounds the warning buzzer if necessary WARNING OPERATION CONDITIONS If all of the following conditions are fulfilled: • Vehicle speed is approximately MPH (7 km/h) or higher • Parking brake switch ON WARNING CANCEL CONDITIONS Warning is canceled if any of the following conditions are fulfilled: • Vehicle speed is approximately MPH (3 km/h) or less • Parking brake switch OFF Revision: October 2012 WCS-8 2013 Pathfinder NAM DIAGNOSIS SYSTEM (COMBINATION METER) < SYSTEM DESCRIPTION > DIAGNOSIS SYSTEM (COMBINATION METER) A Description INFOID:0000000008945479 COMBINATION METER SELF-DIAGNOSIS MODE B The following meter functions can be checked during Combination Meter Self-Diagnosis Mode: • Pointer sweep of speedometer, tachometer and gauges • Illumination of all LCD segments and color patterns for meter displays • Illumination of all lamps/LEDs that are controlled by the combination meter (regardless of switch status) C STARTING COMBINATION METER SELF-DIAGNOSIS MODE NOTE: • Check combination meter power supply and ground circuits if self-diagnosis mode does not start Refer to MWI-59, "COMBINATION METER : Diagnosis Procedure" Replace combination meter if power supply and ground circuits are found to be normal and self-diagnosis mode does not start Refer to MWI-82, "Removal and Installation" • Combination meter self-diagnosis mode will function with the ignition switch in ON Combination meter selfdiagnosis mode will exit upon turning the ignition switch to OFF How to Initiate Self-Diagnosis Mode Press and hold the trip reset switch while turning the ignition switch ON After seconds release trip reset switch, then press the trip reset switch times within seconds after the ignition switch is turned ON When the diagnosis function is activated, the meter illuminates all of the following: • Warning lights/indicators • Meter assembly • Information display color bars red, green, blue and white (1) • Odometer, trip A/B odometers and CVT indicator LCD display segments (2) Pressing and holding the trip reset switch performs the pointer sweep test D E F G H I J K AWNIA2543GB CONSULT Function (METER/M&A) INFOID:0000000008945480 L M APPLICATION ITEMS CONSULT can display each diagnostic item using the diagnostic test modes shown METER/M&A Diagnosis mode SELF DIAGNOSTIC RESULT DATA MONITOR WARNING HISTORY CAN DIAG SUPPORT MNTR WCS Description Displays combination meter self-diagnosis results O Displays combination meter input/output data in real time Lighting history of the warning lamp and indicator lamp can be checked The result of transmit/receive diagnosis of CAN communication can be read SELF DIAG RESULT Refer to MWI-29, "DTC Index" DATA MONITOR Display Item List Revision: October 2012 WCS-9 2013 Pathfinder NAM P DIAGNOSIS SYSTEM (COMBINATION METER) < SYSTEM DESCRIPTION > X: Applicable Display item [Unit] SPEED METER SPEED OUTPUT [mph or km/h] MAIN SIGNALS Description X Displays the value of vehicle speed signal X Vehicle speed signal value transmitted to other units via CAN communication ODO OUTPUT [mph or km/h] Odometer signal value transmitted to other units via CAN communication TACHO METER [rpm] X Value of the engine speed signal received from ECM via CAN communication FUEL METER [L] X Fuel level indicated on combination meter W TEMP METER [°F] or [°C] X Displays the value of engine coolant temperature signal, which is input from ECM ABS W/L [On/Off] Displays [ON/OFF] condition of ABS warning indicator VDC/TCS IND [On/Off] Displays [ON/OFF] condition of VDC OFF warning lamp SLIP IND [On/Off] Displays [ON/OFF] condition of SLIP indicator lamp BRAKE W/L [On/Off] Displays [ON/OFF] condition of brake warning indicator FR FOG IND [Off] Displays [ON/OFF] condition of front fog lamp indicator DOOR W/L [ON/OFF] Displays [ON/OFF] condition of door warning message TRUNK/GLAS-H [ON/OFF] Displays [ON/OFF] condition of glass hatch warning message HI-BEAM IND [ON/OFF] Displays [ON/OFF] condition of high beam indicator TURN IND [On/Off] Displays [ON/OFF] condition of turn indicator LIGHT IND [On/Off] Displays [ON/OFF] condition of light indicator OIL W/L [ON/OFF] Displays [ON/OFF] condition of low oil pressure warning message MIL [ON/OFF] Displays [ON/OFF] condition of malfunction indicator CRUISE IND [Off] Displays [ON/OFF] condition of CRUISE indicator in the information display SET IND [On/Off] Displays [ON/OFF] condition of SET indicator in the information display O/D OFF IND [On/Off] Displays [ON/OFF] condition of O/D OFF indicator CVT IND [On/Off] Displays [ON/OFF] condition of CVT indicator in the information display 4WD W/L [On/Off] Displays [ON/OFF] condition of 4WD warning message in the information display FUEL W/L [On/Off] Displays [ON/OFF] condition of low-fuel warning message WASHER W/L [On/Off] Displays [ON/OFF] condition of low washer fluid warning message Revision: October 2012 WCS-10 2013 Pathfinder NAM VENTILATION SYSTEM < SYSTEM DESCRIPTION > Upper Vent : ON • DUAL: OFF • Rear ventilator: Close 18°C (60° Temperature control switch Other than 18°C (60°F) × × — — — — × × — — — — — × × — × × — — — — — × × — — — — — × × × — — — — — — × — — — — — — × A B C Front Air Control D Discharge air flow Air outlet / distribution Mode position VENT Condition Upper Vent: ON 18°C (60°F) Temperature control switch Other than Center (1) Side (2) Rear (3) Front (4) Center (5) × × — — — DEF (6) F × — — — — — × × — × × — — — — — × × — — — — — × × × — — — — — ì ì ã DUAL: OFF ã Rear ventilator: Close E ì 18C (60°F)*1 *2 FOOT G H VTL Rear J K L AWLIA2041ZZ M N O P AWLIA2051ZZ Revision: October 2012 VTL-7 2013 Pathfinder NAM VENTILATION SYSTEM < SYSTEM DESCRIPTION > AWLIA2043ZZ Rear Air Control Discharge air flow Air outlet / distribution Mode position VENT Condition Upper Vent: ON • DUAL: OFF • Rear ventilator: Close FOOT Center (3) Side (7) Center (5) Rear (8) 18°C (60°F) × × — — Other than 18°C × × — — — × × — × — — — — × Temperature control switch (60°F)*1 • *1: Air blow is also supplied to front foot until passenger room temperature stabilizes when temperature setting is other than 18°C (60°F) At that time, air blowing is the same as 18°C (60°F) setting • *2: During automatic defogging control (Forest air system) Revision: October 2012 VTL-8 2013 Pathfinder NAM DUCTS AND GRILLES < REMOVAL AND INSTALLATION > REMOVAL AND INSTALLATION A DUCTS AND GRILLES Exploded View INFOID:0000000008507437 B C Front D E F G H VTL J K L M N O P ALIIA0527ZZ Revision: October 2012 VTL-9 2013 Pathfinder NAM DUCTS AND GRILLES < REMOVAL AND INSTALLATION > Defroster nozzle Side defroster duct (LH) Front heating and cooling unit assembly Front floor connecting duct (LH) Front floor duct (LH) Adaptor duct (to center blower unit) Front floor duct (RH) Front floor connecting duct (RH) 10 Ionizer (if equipped) Center ventilator duct 11 Side defroster duct (RH) DEFROSTER NOZZLE DEFROSTER NOZZLE : Removal and Installation INFOID:0000000008507438 REMOVAL Remove the side defroster ducts (LH/RH) Refer to VTL-10, "SIDE DEFROSTER DUCT : Removal and Installation" Remove the screws and the defroster nozzle INSTALLATION Installation is in the reverse order of removal CENTER VENTILATOR DUCT CENTER VENTILATOR DUCT : Removal and Installation INFOID:0000000008507439 REMOVAL Remove the side defroster ducts (LH/RH) Refer to VTL-10, "SIDE DEFROSTER DUCT : Removal and Installation" Remove the screws and the center ventilator duct INSTALLATION Installation is in the reverse order of removal SIDE DEFROSTER DUCT SIDE DEFROSTER DUCT : Removal and Installation INFOID:0000000008507440 REMOVAL Remove the instrument panel assembly Refer to IP-15, "Removal and Installation" Disconnect the harness connector from the ionizer (if equipped) Remove the screws from the side defroster duct Remove the side defroster duct INSTALLATION Installation is in the reverse order of removal FRONT FLOOR DUCT FRONT FLOOR DUCT : Removal and Installation - Front Floor Connecting Duct INFOID:0000000008507441 REMOVAL Remove the center console side finisher Refer to IP-18, "Exploded View" Unclip the harness wiring from the front floor connecting duct (RH) Remove the front floor connecting duct INSTALLATION Installation is in the reverse order of removal FRONT FLOOR DUCT : Removal and Installation - Front Floor Duct INFOID:0000000008507442 REMOVAL Remove front floor trim Refer to INT-21, "Removal and Installation" Revision: October 2012 VTL-10 2013 Pathfinder NAM DUCTS AND GRILLES < REMOVAL AND INSTALLATION > Remove the front floor duct screws Remove the front floor duct A INSTALLATION Installation is in the reverse order of removal B ADAPTOR DUCT ADAPTOR DUCT : Removal and Installation INFOID:0000000008507443 C REMOVAL Remove the center console assembly Refer to IP-18, "Removal and Installation" Release the adaptor duct clip Remove the center console bracket Remove the adaptor duct (to center blower unit) D E INSTALLATION Installation is in the reverse order of removal F Exploded View INFOID:0000000008507444 G Center H VTL J K L ALIIA0528ZZ Center blower unit Center floor connecting duct Center floor duct (RH) Rear center ventilator duct M Center floor duct (LH) REAR CENTER VENTILATOR DUCT REAR CENTER VENTILATOR DUCT : Removal and Installation N INFOID:0000000008507445 O REMOVAL Remove center console rear finisher Refer to IP-18, "Exploded View" P Revision: October 2012 VTL-11 2013 Pathfinder NAM DUCTS AND GRILLES < REMOVAL AND INSTALLATION > Remove the two screws (A) from the rear center ventilator duct (1) ALIIA0540ZZ Remove the rear center ventilator duct INSTALLATION Installation is in the reverse order of removal CENTER FLOOR DUCT CENTER FLOOR DUCT : Removal and Installation - Center Floor Connecting Duct INFOID:0000000008507446 REMOVAL Remove the rear floor trim Refer to INT-21, "Removal and Installation" Remove the center floor connecting duct screws Remove the center floor connecting duct INSTALLATION Installation is in the reverse order of removal CENTER FLOOR DUCT : Removal and Installation - Center Floor Duct INFOID:0000000008507447 REMOVAL Remove the rear floor trim Refer to INT-21, "Removal and Installation" Remove the center floor duct screws Remove the center floor duct INSTALLATION Installation is in the reverse order of removal Exploded View Revision: October 2012 INFOID:0000000008507448 VTL-12 2013 Pathfinder NAM DUCTS AND GRILLES < REMOVAL AND INSTALLATION > Rear A B C D E F G H ALIIA0529ZZ Rear ventilator duct Rear ventilator duct Rear ventilator duct Rear ventilator duct lower Rear heating and cooling unit assembly Rear ventilator duct upper VTL REAR VENTILATOR DUCT UPPER REAR VENTILATOR DUCT UPPER : Removal and Installation J INFOID:0000000008507449 REMOVAL Remove the luggage side lower finisher (RH) Refer to INT-28, "LUGGAGE SIDE LOWER FINISHER : Removal and Installation" Remove the clips that retain the rear ventilator duct upper Remove the rear ventilator duct upper K L INSTALLATION M Installation is in the reverse order of removal REAR VENTILATOR DUCT LOWER REAR VENTILATOR DUCT LOWER : Removal and Installation INFOID:0000000008507450 N Remove the rear ventilator duct upper Refer to VTL-13, "REAR VENTILATOR DUCT UPPER : Removal and Installation" Remove the rear ventilator duct lower screw Remove the rear ventilator duct lower O REMOVAL INSTALLATION Installation is in the reverse order of removal REAR VENTILATOR DUCT Revision: October 2012 VTL-13 2013 Pathfinder NAM P DUCTS AND GRILLES < REMOVAL AND INSTALLATION > REAR VENTILATOR DUCT : Removal and Installation INFOID:0000000008507451 REMOVAL Remove the luggage side lower finisher (LH) Refer to INT-28, "LUGGAGE SIDE LOWER FINISHER : Removal and Installation" Remove the clips that retain the rear ventilator duct Remove the rear ventilator duct INSTALLATION Installation is in the reverse order of removal REAR VENTILATOR DUCT REAR VENTILATOR DUCT : Removal and Installation INFOID:0000000008507452 REMOVAL Remove rear ventilator duct Refer to VTL-14, "REAR VENTILATOR DUCT : Removal and Installation" Remove rear ventilator duct screw Remove rear ventilator duct INSTALLATION Installation is in the reverse order of removal REAR VENTILATOR DUCT REAR VENTILATOR DUCT : Removal and Installation INFOID:0000000008507453 REMOVAL Remove the storage box Refer to INT-30, "STORAGE BOX : Removal and Installation" Remove the car jack bracket Remove rear ventilator duct Refer to VTL-14, "REAR VENTILATOR DUCT : Removal and Installation" Remove the two screws that retain rear ventilator duct Remove rear ventilator duct INSTALLATION Installation is in the reverse order of removal Revision: October 2012 VTL-14 2013 Pathfinder NAM DUCTS AND GRILLES < REMOVAL AND INSTALLATION > Exploded View INFOID:0000000008507454 A B C D E F G H VTL J ALIIA0533ZZ Instrument panel Side defroster grille (LH) Side ventilator grille (LH) Center ventilator grille (LH) Center ventilator grille (RH) Side ventilator grille (RH) Side defroster grille (RH) K CENTER VENTILATOR GRILLE L CENTER VENTILATOR GRILLE : Removal and Installation INFOID:0000000008507455 REMOVAL M Remove cluster lid D Refer to IP-24, "Removal and Installation" Release the center ventilator grille pawls (A) from cluster lid D using a suitable tool : Pawl N O P ALIIA0541ZZ Remove the center ventilator grille INSTALLATION Installation is in the reverse order of removal Revision: October 2012 VTL-15 2013 Pathfinder NAM DUCTS AND GRILLES < REMOVAL AND INSTALLATION > SIDE VENTILATOR GRILLE SIDE VENTILATOR GRILLE : Removal and Installation INFOID:0000000008507456 REMOVAL Remove the instrument lower panel LH (LH only) Refer to IP-25, "Removal and Installation" Remove the glove box assembly (RH only) Refer to IP-26, "Removal and Installation" Release the side ventilator grille pawls (A) using a suitable tool : Pawl ALIIA0535ZZ Remove the side ventilator grille INSTALLATION Installation is in the reverse order of removal SIDE DEFROSTER GRILLE SIDE DEFROSTER GRILLE : Removal and Installation INFOID:0000000008507457 REMOVAL Release the side defroster grille pawl (A) using a suitable tool : Pawl ALIIA0534ZZ Remove the side defroster grille (LH/RH) INSTALLATION Installation is in the reverse order of removal REAR CENTER VENTILATOR GRILLE REAR CENTER VENTILATOR GRILLE : Removal and Installation INFOID:0000000008507458 REMOVAL Remove center console rear finisher Refer to IP-18, "Exploded View" Remove the rear center ventilator duct from the center console rear finisher Release the clips, then remove the rear center ventilator grille Revision: October 2012 VTL-16 2013 Pathfinder NAM DUCTS AND GRILLES < REMOVAL AND INSTALLATION > Release the pawl (A) to separate the rear center ventilator grille (if necessary) A B C ALIIA0543ZZ D INSTALLATION Installation is in the reverse order of removal REAR VENTILATOR GRILLE E REAR VENTILATOR GRILLE : Removal and Installation INFOID:0000000008507459 F REMOVAL Release the rear ventilator grille pawls (A) using a suitable tool : Pawl : Front G H VTL ALIIA0536ZZ J Remove the rear ventilator grille INSTALLATION K Installation is in the reverse order of removal L M N O P Revision: October 2012 VTL-17 2013 Pathfinder NAM BLOWER UNIT < REMOVAL AND INSTALLATION > BLOWER UNIT Exploded View INFOID:0000000008507460 REMOVAL ALIIA0562ZZ Front heating and cooling unit assembly Steering member DISASSEMBLY ALIIA0560ZZ Front heating and cooling unit assembly Front evaporator Heater case side cover Air mix door motor (driver) Distribution module Intake door motor Front blower motor Upper floor connecting duct (RH) Air mix door motor (rear) 10 In-cabin microfilter cover 11 In-cabin microfilter 12 Drain hose 13 Expansion valve grommet 14 Expansion valve 15 Front heater core 16 Air mix door motor (passenger) 17 Aspirator hose 18 Upper floor connecting duct (LH) 19 Heater core pipe cover 20 Mode door motor FRONT BLOWER UNIT Revision: October 2012 VTL-18 2013 Pathfinder NAM BLOWER UNIT < REMOVAL AND INSTALLATION > FRONT BLOWER UNIT : Removal and Installation INFOID:0000000008507461 A REMOVAL Remove the front heating and cooling unit assembly Refer to HA-41, "HEATING AND COOLING UNIT ASSEMBLY : Removal and Installation - Front Heating and Cooling Unit Assembly" Remove front blower unit screws Remove the front blower unit from the front heating and cooling unit assembly B C INSTALLATION Installation is in the reverse order of removal FRONT BLOWER MOTOR D FRONT BLOWER MOTOR : Removal and Installation INFOID:0000000008507462 E REMOVAL Remove glove box assembly Refer to IP-26, "Removal and Installation" Disconnect the harness connector (A) from the front blower motor Remove front blower motor screws (B) and the front blower motor (1) F G H JMIIA0556ZZ VTL INSTALLATION Installation is in the reverse order of removal J CENTER BLOWER UNIT CENTER BLOWER UNIT : Removal and Installation INFOID:0000000008507463 K L M N O P ALIIA0537ZZ Center console assembly Center blower unit Center console rear finisher REMOVAL Remove the center console assembly Refer to IP-18, "Removal and Installation" Revision: October 2012 VTL-19 2013 Pathfinder NAM BLOWER UNIT < REMOVAL AND INSTALLATION > Remove the center console bracket Disconnect the harness connectors from the center blower unit Remove the center blower unit bolts and the center blower unit INSTALLATION Installation is in the reverse order of removal CENTER BLOWER MOTOR CENTER BLOWER MOTOR : Removal and Installation INFOID:0000000008507464 ALIIA0531ZZ Center blower unit upper case Rear shut-off door motor Center blower unit lower case Center blower motor Rear air mix door motor PTC elements heater REMOVAL Remove the center blower unit Refer to VTL-19, "CENTER BLOWER UNIT : Removal and Installation" Disconnect the harness connector from the center blower motor Remove the center blower motor screws Remove the center blower motor INSTALLATION Installation is in the reverse order of removal REAR BLOWER MOTOR Revision: October 2012 VTL-20 2013 Pathfinder NAM BLOWER UNIT < REMOVAL AND INSTALLATION > REAR BLOWER MOTOR : Removal and Installation INFOID:0000000008507465 A B C D E F G H VTL ALIIA0532ZZ Rear heating and cooling unit assembly Rear blower motor Front K REMOVAL J Remove the rear heating and cooling unit assembly Refer to HA-43, "HEATING AND COOLING UNIT ASSEMBLY : Removal and Installation - Rear Heating and Cooling Unit Assembly" Disconnect the harness connector from the rear blower motor Remove the rear blower motor screws and rear blower motor INSTALLATION L M Installation is in the reverse order of removal N O P Revision: October 2012 VTL-21 2013 Pathfinder NAM