© ISO 2016 Tractors, machinery for agriculture and forestry, powered lawn and garden equipment — Symbols for operator controls and other displays — Part 3 Symbols for powered lawn and garden equipment[.]
INTERNATIONAL STANDARD ISO 3767-3 Third edition 2016-09-01 Tractors, machinery for agriculture and forestry, powered lawn and garden equipment — Symbols for operator controls and other displays — Part 3: Symbols for powered lawn and garden equipment Tracteurs, matériels agricoles et forestiers, matériel moteur pour jardins et pelouses — Symboles pour les commandes de l’opérateur et autres indications — Partie 3: Symboles pour matériel moteur pour jardins et pelouses Reference number ISO 3767-3:2016(E) © ISO 2016 ISO 3767-3:2016(E) COPYRIGHT PROTECTED DOCUMENT © ISO 2016, Published in Switzerland All rights reserved Unless otherwise specified, no part o f this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission Permission can be requested from either ISO at the address below or ISO’s member body in the country o f the requester ISO copyright o ffice Ch de Blandonnet • CP 401 CH-1214 Vernier, Geneva, Switzerland Tel +41 22 749 01 11 Fax +41 22 749 09 47 copyright@iso.org www.iso.org ii © ISO 2016 – All rights reserved ISO 3767-3:2016(E) Contents Page Foreword iv Scope Normative references Terms and definitions General Colour Development of new symbols Adaptation of symbols as digital display icons Lawn and garden tractor symbols Riding lawn mower symbols 10 10 Grass-cutting equipment symbols 10 11 Tiller symbols 14 12 Snow removal equipment symbols 15 Bibliography 16 © ISO 2016 – All rights reserved iii ISO 3767-3:2016(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies) The work o f preparing International Standards is normally carried out through ISO technical committees Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters o f electrotechnical standardization The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part In particular the different approval criteria needed for the di fferent types o f ISO documents should be noted This document was dra fted in accordance with the editorial rules of the ISO/IEC Directives, Part (see www.iso.org/directives) Attention is drawn to the possibility that some o f the elements o f this document may be the subject o f patent rights ISO shall not be held responsible for identi fying any or all such patent rights Details o f any patent rights identified during the development o f the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents) Any trade name used in this document is in formation given for the convenience o f users and does not constitute an endorsement For an explanation on the meaning o f ISO specific terms and expressions related to formity assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary in formation The committee responsible for this document is ISO/TC 23, Tractors and machinery for agriculture and forestry, SC 14, Operator controls, operator symbols and other displays, operator manuals This third edition cancels and replaces the second edition (ISO 3767-3:1995), which has been technically revised Many new symbols have been added A list of all the parts in the ISO 3767 series can be found on the ISO website iv © ISO 2016 – All rights reserved INTERNATIONAL STANDARD ISO 3767-3:2016(E) Tractors, machinery for agriculture and forestry, powered lawn and garden equipment — Symbols for operator controls and other displays — Part 3: Symbols for powered lawn and garden equipment Scope T h i s c ument s ta nda rd i z e s s ymb ol s for NO TE s ymb ol s and garden equipment ISO agr ic u ltu l s ymb o l s NO TE 767-1 fore s tr y m ach i ner y, for trac to rs covers com mon m ach i ner y, a nd a nd m ach i ner y m a nu a l p or tab le fore s tr y u s e on op erator control s and o ther d i s plays on p owere d lawn p owere d ISO th at l awn 767- app l y a nd covers to mu l tip le ga rden s ymb o l s typ e s e qu ip ment of ISO for fore s tr y agr ic u ltu l 767-2 trac tors covers m ach i ner y ISO s ymb ol s 767-5 a nd for covers m ach i ne s I S O 70 0 a nd I E C 417 c a n b e co n s u lte d for add itio n a l i nter n atio n a l l y s ta nda rd i z e d s ymb o l s o f potential relevance to powered lawn and garden equipment Normative references T he fol lowi ng c u ments are re ferre d to i n the tex t i n s uch a way th at s ome or a l l o f thei r content s titute s re qu i rements o f th i s c u ment For date d re ference s , on ly the e d ition cite d app l ie s For u ndate d re ference s , the late s t e d ition o f the re ference d c ument (i nclud i ng a ny amend ments) appl ie s ISO 3767-1:2016, Tractors, machinery for agriculture and forestry, powered lawn and garden equipment — Symbols for operator controls and other displays—Part 1: Common symbols IEC 80416-1, Basic principles for graphical symbols for use on equipment — Part 1: Creation of graphical symbols for registration ISO 80416-2, Basic principles for graphical symbols for use on equipment — Part 2: Form and use ofarrows IEC 80416-3, Basic principles for graphical symbols for use on equipment — Part 3: Guidelines for the application of graphical symbols Terms and definitions For the pu r p o s e s o f th i s c u ment, the fol lowi ng term s and defi n ition s apply ISO and IEC maintain terminological databases for use in standardization at the following addresses: — IEC Electropedia: available at http://www.electropedia.org/ — ISO Online browsing platform: available at http://www.iso.org/obp © ISO 2016 – All rights reserved ISO 3767-3:2016(E) 3.1 symbol graphical symbol visually perceptible figure used to transmit in formation independent o f language Note to entry: It may be produced by drawing, printing or other means Letters, numerals and mathematical symbols may be used as symbols or symbol elements For some specific applications, groups o f letters (for example, AUTO, STOP) are used as symbols or symbol elements Note to entry: Letters and numerals are not registered by ISO/TC 145/SC or published in ISO 7000 unless they are symbol elements embedded in graphical symbols 3.2 icon digital display icon digitized (pixelated) representation o f a graphical symbol, usually used on a reconfigurable electronic display screen or graphical user inter face (GUI) Note to entry: A single symbol can be represented by multiple icons, each o f a di fferent size, pixel count or colourization 4.1 General Except where indicated in subsequent clauses, symbols shall be used as shown in this document 4.2 Selected symbols, which are shown in outline form in this document, may be filled in actual use for enhanced clarity o f reproduction and improved visual perception by the operator, except as otherwise specified for individual symbols, and in accordance with IEC 80416-3 Limitations inherent in some reproduction and display technologies can require increased line width or other minor modifications o f symbols Such modifications are allowed, provided that the symbol remains conceptually unchanged in its basic graphical elements and is easily discernible by the operator 4.3 4.4 To improve the appearance and perceptibility o f a graphical symbol, or to coordinate with the design o f the equipment to which it is applied, it can be necessary to modi fy the symbol as indicated in IEC 80416-3 (for example, to change the line width or to round the corners o f the symbol) Such modifications are allowed, provided that the essential perceptible characteristics o f the symbol are maintained 4.5 For actual use, all symbols shall be reproduced large enough to be easily discernible by the operator Follow IEC 80416-1 for the proper sizing o f symbols Symbols grouped together in a display or on a set o f controls should be scaled to the same degree relative to the corner marks o f the symbol original as shown in this document in order to maintain the correct visual relationship among the symbols Symbols shall be used in the orientation shown in this document, unless rotation or mirror imaging is specifically allowed for individual symbols Most symbols are constructed using a building block approach in which various symbols and symbol elements are combined in a logical manner to produce a new symbol 4.6 In some cases, symbols may be used in conjunction, without being combined into a composite symbol, to convey the same meaning as the composite symbol 4.7 4.8 Symbols are generally intended to replace a word or words with a graphical image that has the same meaning for all operators, regardless of their native language However, the use of a graphical symbol to identi fy a control or display does not preclude the use o f words in conjunction with that control or display © ISO 2016 – All rights reserved ISO 3767-3:2016(E) I f a symbol shows a machine or parts o f a machine from a side view, a machine moving from right to le ft across the symbol area shall be assumed I f a symbol shows a machine or parts o f a machine from an overhead view, a machine moving from bottom to top across the symbol area shall be assumed 4.9 Symbols on controls and displays shall have a good contrast to their background A white or lightcoloured symbol on a black or dark-coloured background is pre ferred for most controls Displays may use either a white or light-coloured symbol on a black or dark-coloured background or a black or darkcoloured symbol on a white or light-coloured background, depending upon which alternative provides the best visual perception When a symbol image is reversed (for example, from black-on-white to whiteon-black or vice versa) this reversal shall be done for the entire symbol 4.10 4.11 I f symbols are cast, moulded, embossed or stamped into a surface, the symbols shall be visually distinct from that surface without dependence on colour Symbols shall be located on or adjacent to the control or display that is being identified Where more than one symbol is required for a control, the symbols shall be located in relation to the control such that movement o f the control towards the symbols shall e ffect the function depicted by that symbol 4.12 4.13 Arrows used in symbols shall form to the requirements o f ISO 80416-2 IEC 80416-1 shall be consulted for the general principles for creating symbol originals IEC 80416-3 should be consulted for guidelines for the application o f symbols 4.14 ISO/IEC registration numbers are shown for symbols which are registered in ISO 7000 or IEC 60417 NOTE Symbol originals are approved and registered either by ISO/TC 145/SC and published in ISO 7000 or by IEC/SC 3C and published in IEC 60417 In some cases, modified or application symbols, rather than the registered symbol originals, are standardized in this document 4.15 When letters or numerals are used in a symbol, the font shown shall not be considered definitive Other fonts may be used so long as the letters and numerals remain legible 4.16 Symbols in this document are shown within marks that delimit the corners o f the 75 mm square basic pattern from IEC 80416-1 Corner marks are not part o f the symbol, but are provided to ensure consistent presentation o f all symbol graphics Colour When used on illuminated displays, the following colours shall have the meanings indicated: — red denotes a failure, serious malfunction or operating condition that requires immediate attention; — yellow or amber denotes a condition outside normal operating limits; — green denotes a normal operating condition Development of new symbols Prior to developing a new symbol, a search should be conducted for previously standardized symbols with the same or similar meaning to what is needed ISO 7000 and IEC 60417 (both available in database form) are compilations o f internationally standardized symbols which can be use ful both for finding appropriate symbols that not appear in ISO 3767 and for generating concepts that can be used in the development o f new symbols 6.1 © ISO 2016 – All rights reserved ISO 3767-3:2016(E) New symbols shall be developed in accordance with the principles o f ISO 3767-1:2016, Annex A IEC 80416-1 should be consulted for general principles for the creation o f symbols Arrows shall be in 6.2 accordance with ISO 80416-2 Different arrow forms have different meanings according to ISO 804162 Care should be taken to use the correct arrow form Following the guidelines of ISO 3767-1:2016, Annex A makes possible the development o f symbols appropriate in graphical form and content for international standardization and ISO 7000 registration Symbols proposed for standardization in this document shall include a short explanation o f the unction or expected use o f the symbol 6.3 f NOTE IEC 80416-1 uses the term “description” for this type o f in formation and provides guidelines for writing descriptions for symbols intended for standardization in ISO 7000 or IEC 60417 The descriptions for symbols standardized in this document can serve as examples Adaptation of symbols as digital display icons Symbols can be adapted for use as digital display icons on visual display units, reconfigurable displays or other electronic displays Such adaptations should follow the principles o f ISO 80416-4 Special care should be taken to ensure that digital display icons preserve the visual impression o f the symbol from which the icon is adapted The same principles regarding use o f colour with symbols apply to the use o f colour with digital display icons Lawn and garden tractor symbols No 8.1 Graphical symbol ISO/IEC registration number Symbol title and description Lawn and garden tractor (side view of machine) To identi fy the tractor from a side (profile) view Use as a base symbol for developing tractor symbols that use a side (profile) view 8.2 ISO 7000-3477 ISO 7000-3478 Lawn and garden tractor (overhead view of machine) To identi fy the tractor from an overhead (plan) view Use as a base symbol for developing tractor symbols that use an overhead (plan) view 8.3 Lawn and garden tractor, forward movement (side view of machine) ISO 7000-3479 To identi fy the control that moves the tractor in a forward direction To indicate that the tractor is moving forward The tractor is shown in a side (profile) view 8.4 Lawn and garden tractor, rearward movement (side view of machine) ISO 7000-3480 To identi fy the control that moves the tractor in a rearward direction To indicate that the tractor is moving rearward The tractor is shown in a side (profile) view © ISO 2016 – All rights reserved ISO 3767-3:2016(E) No Graphical symbol 8.5 ISO/IEC registration number Symbol title and description ISO 7000-3481 Lawn and garden tractor, forward movement (overhead view of machine) To identi fy the control th at mo ve s the trac to r i n a forward direction To indicate that the tractor is moving forward T h i s s ymb ol i s vie we d from the p ers p e c tive o f a person looking at the tractor from above the machine 8.6 Lawn and garden tractor, rearward movement (overhead view of machine) ISO 7000-3482 To identi fy the control th at mo ve s the trac to r i n a rearward direction To indicate that the tractor is moving rearward T h i s s ymb ol i s vie we d from the p ers p e c tive o f a person looking at the tractor from above the machine 8.7 Lawn and garden tractor, ground speed ISO 7000-3483 To identi fy the d i s p l ay th at s hows the grou nd s p e e d o f the tractor To indicate the ground speed of the tractor 8.8 Lawn and garden tractor, ground speed, automatic operating mode ISO 7000-3484 To identi fy the control th at ac tivate s the autom atic mode for tractor ground speed 8.9 ISO 7000-3259 Lawn and garden tractor, front wheel drive To identi fy the control for the trac tor front whe el drive To indicate the operational status of the tractor front wheel drive function 8.10 Lawn and garden tractor, front wheel drive, automatic operation To identi fy the control for ISO 7000-3485 the autom atic op eratio n o f the tractor front wheel drive To indicate that the tractor front wheel drive is in automatic operation mode Front wheel drive is engaged and disengaged auto m atic a l l y b a s e d o n o p erati ng co nd ition s © ISO 2016 – All rights reserved ISO 3767-3:2016(E) No 8.11 Graphical symbol ISO 7000-3260 Tractor blade To identi fy the control garden tractor 8.12 ISO/IEC registration number Symbol title and description for the b l ade o n the l awn a nd ISO 7000-3486 Tractor blade, raise To identi fy the control th at i s e s the b l ade on the lawn and garden tractor To indicate that the tractor blade is being raised or is in the raised position 8.13 ISO 7000-3487 Tractor blade, lower To identi fy the control th at lowers the b l ade on the lawn and garden tractor To indicate that the tractor blade is being lowered or is in the lowered position 8.14 ISO 7000-3261 Tractor blade, hold To identi fy the control th at hold s the trac to r b l ade i n a s p e c i fie d p o s ition To indicate that the tractor blade is in the hold condition 8.15 T r a c t o r b l a d e , f l o a ISO 7000-3488 t To identi fy the control th at a l lows the trac to r b l ade to move up and down with the contour of the ground To i n d i c ate th a t th e tr ac to r b l ad e i s i n the fl o at condition 8.16 ISO 7000-1572 Power take-off (PTO) To identi fy the control for the p ower ta ke - o ff ( P TO) s ys tem To indicate the operational status of the PTO S ymb ol m ay b e u s e d with a nu mer ic a l i nd ic ato r o f 8.17 rated PTO rotational speed See 8.20, 8.21 and 8.22 Power take-off (PTO), direction of rotation, clockwise ISO 7000-1664 To indicate that the PTO shaft rotates clockwise For anti-clockwise rotation, use mirror image of ISO 7000-1664 (see 8.18) Direction of rotation is from the perspective of a person looking at the end of the PTO shaft © ISO 2016 – All rights reserved ISO 3767-3:2016(E) No Graphical symbol 8.18 8.19 Symbol title and description Power take-off (PTO), direction of rotation, anti-clockwise To indicate that the PTO shaft rotates anti-clockwise For clockwise rotation, use ISO 7000-1664 (see 8.17) Direction of rotation is from the perspective of a person looking at the end of the PTO shaft Power take-off (PTO), rotational speed ISO/IEC registration number Mirror image of ISO 7000-1664 ISO 7000-3194 To identi fy the co ntrol th at s e ts or adj u s ts the rotational speed of the PTO shaft To indicate the rotational speed of the PTO S ymb o l element “n/m i n” m ay b e rep l ace d b y a 8.20 numerical indicator of PTO rated rotational speed See 8.20, 8.21 and 8.22 Power take-off (PTO), rated rotational speed 540 r/min To identi fy the control for Application of ISO 7000-3194 the P TO rate d at r/m i n To indicate the operational status of the PTO rated at 540 r/min 8.21 Power take-off (PTO), rated rotational speed 000 r/min To identi fy the control for the Application of ISO 7000-3194 P TO rate d at 0 r/min To indicate the operational status of the PTO rated at 000 r/min 8.22 Power take-off (PTO), rated rotational speed 000 r/min To identi fy the control for the Application of ISO 7000-3194 P TO rate d at 0 r/min To indicate the operational status of the PTO rated at 000 r/min 8.23 Power take-off (PTO), clockwise rotational speed ISO 7000-3432 To identi fy the co ntrol th at s e ts or adj u s ts the clockwise rotational speed of the PTO shaft To indicate the clockwise rotational speed of the PTO shaft S ymb o l element “n/m i n” m ay b e rep l ace d b y a numerical indicator of PTO rated rotational speed in the clockwise direction See 8.25, 8.27 and 8.29 Direction of rotation is from the perspective of a person looking at the end of the PTO shaft © ISO 2016 – All rights reserved ISO 3767-3:2016(E) No 8.24 Graphical symbol Symbol title and description Power take-off (PTO), anti-clockwise rotational speed ISO/IEC registration number ISO 7000-3433 To identi fy the control th at s e ts o r adj u s ts the anti-clockwise rotational speed of the PTO shaft To indicate the anti-clockwise rotational speed of the PTO shaft S ymb ol element “n/m i n” m ay b e rep l ace d b y a 8.25 numerical indicator of PTO rated rotational speed in the anti-clockwise direction See 8.26, 8.28 and 8.30 Direction of rotation is from the perspective of a person looking at the end of the PTO shaft Power take-off (PTO), rated clockwise rotational speed, 540 r/min To identi fy the control 8.26 the P TO rate d at r/m i n in the clockwise direction To indicate that the PTO operates in the clockwise direction of rotation at a rotational speed of 540 r/min To indicate the operational status of the PTO rated at 540 r/min in the clockwise direction Direction of rotation is from the perspective of a person looking at the end of the PTO shaft Power take-off (PTO), rated anti-clockwise rotational speed, 540 r/min To identi fy the control 8.27 for for Power take-off (PTO), rated clockwise rotational speed, 000 r/min for Application of ISO 7000-3433 the P TO rate d at r/m i n in the anti-clockwise direction To indicate that the PTO operates in the anti-clockwise direction of rotation at a rotational speed of 540 r/min To indicate the operational status of the PTO rated at 540 r/min in the anti-clockwise direction Direction of rotation is from the perspective of a person looking at the end of the PTO shaft To identi fy the control Application of ISO 7000-3432 Application of ISO 7000-3432 the P TO rate d at 000 r/min in the clockwise direction To indicate that the PTO operates in the clockwise direction of rotation at a rotational speed of 000 r/min To indicate the operational status of the PTO rated at 000 r/min in the clockwise direction Direction of rotation is from the perspective of a person looking at the end of the PTO shaft © ISO 2016 – All rights reserved ISO 3767-3:2016(E) No Graphical symbol 8.28 Symbol title and description Power take-off (PTO), rated anti-clockwise rotational speed, 000 r/min To identi fy the co ntrol 8.29 Power take-off (PTO), rated clockwise rotational speed, 000 r/min Power take-off (PTO), rated anti-clockwise rotational speed, 000 r/min for Application of ISO 7000-3432 the P TO rate d at 000 r/min in the clockwise direction To indicate that the PTO operates in the clockwise direction of rotation at a rotational speed of 000 r/min To indicate the operational status of the PTO rated at 000 r/min in the clockwise direction Direction of rotation is from the perspective of a person looking at the end of the PTO shaft To identi fy the co ntrol 8.31 for Application of ISO 7000-3433 the P TO rate d at 000 r/min in the anti-clockwise direction To indicate that the PTO operates in the anti-clockwise direction of rotation at a rotational speed of 000 r/min To indicate the operational status of the PTO rated at 000 r/min in the anti-clockwise direction Direction of rotation is from the perspective of a person looking at the end of the PTO shaft To identi fy the control 8.30 for ISO/IEC registration number Application of ISO 7000-3433 the P TO rate d at 000 r/min in the anti-clockwise direction To indicate that the PTO operates in the anti-clockwise direction of rotation at a rotational speed of 000 r/min To indicate the operational status of the PTO rated at 000 r/min in the anti-clockwise direction Direction of rotation is from the perspective of a person looking at the end of the PTO shaft Power take-off (PTO), failure To indicate a failure or malfunction of the power take-off (PTO) ISO 1572 (see 8.16) with the colour red is an ISO 7000-3434 a ltern ative to th i s s ymb ol 8.32 Power take-off (PTO), load ISO 7000-3195 To identi fy the control th at s e ts the lo ad (to rque) o f the power take-off (PTO) To indicate the load (torque) of the PTO Metric torque units (Nm) are shown; non-metric torque u n its ( lb - ft) m ay b e s ub s titute d © ISO 2016 – All rights reserved ISO 3767-3:2016(E) Riding lawn mower symbols No Graphical symbol 9.1 ISO/IEC registration number Symbol title and description Riding lawn mower (overhead view of machine) To identi fy the l awn mower view Us e a s a b a s e s ymb ol for from ISO 7000-3489 a n o verhe ad ( p l a n) de velopi n g l awn mower s ymb ol s th at u s e a n overhe ad ( p l a n) view ISO 7000-3490 Riding lawn mower, forward direction of movement (overhead view of machine) 9.2 To identi fy the control th at move s the l awn mower i n a forward direction To indicate that the lawn mower is moving forward T h i s s ymb ol i s viewe d from the p ers p e c tive o f a person looking at the lawn mower from above the machine 9.3 ISO 7000-3491 Riding lawn mower, rearward direction of movement (overhead view of machine) To identi fy the control th at move s the l awn mower i n a rearward direction To indicate that the lawn mower is moving rearward T h i s s ymb ol i s viewe d fro m the p ers p e c ti ve o f a person looking at the lawn mower from above the machine 10 Grass-cutting equipment symbols No 10.1 Graphical symbol ISO 7000-3492 Mower deck To identi fy the control 10.2 ISO/IEC registration number Symbol title and description for op eration o f the mower deck ISO 7000-3493 Mower deck, raise To identi fy the control th at i s e s the mower de ck To indicate that the mower deck is being raised or is in the raised (up) position 10.3 ISO 7000-3494 Mower deck, lower To identi fy the control th at lowers the mower de ck To indicate that the mower deck is being lowered or is in the lowered (down) position 10 © ISO 2016 – All rights reserved ISO 3767-3:2016(E) No Graphical symbol 10.4 Symbol title and description ISO/IEC registration number ISO 7000-2114 Cutting unit To identi fy the co ntrol for the b o om-mou nte d c utti ng unit of grass-cutting equipment 10.5 Cutting unit, raise ISO 7000-2115 To identi fy the control th at i s e s the b o om-mou nte d cutting unit without changing the horizontal angle of the cutting unit To indicate that the cutting unit is being raised or is in the raised (up) position 10.6 Cutting unit, lower ISO 7000-2116 To identi fy the control th at lowers the b o om-mou nte d cutting unit without changing the horizontal angle of the cutting unit To indicate that the cutting unit is being lowered or is in the lowered (down) position 10.7 Cutting unit, hold ISO 7000-2117 To identi fy the control th at hold s the b o om-mou nte d c utti ng u n it i n a fi xe d p o s ition To indicate that the cutting unit is in the hold condition 10.8 C u t t i n g u n i t , f l o a t ISO 7000-2118 To identi fy the control th at a l lows the b o om-mou nte d cutting unit to move up and down with the contour of the ground To indicate that the cutting un it is in the flo at condition 10.9 10.10 Cutting unit, transport position ISO 7000-2119 Cutting unit, raise to transport position ISO 7000-2120 To indicate that the boom-mounted cutting unit is in the position for transport To identi fy the co ntrol th at i s e s the b o om-mou nte d cutting unit to the transport position To indicate that the cutting unit is being raised to the transport position 10.11 Cutting unit, lower from transport position ISO 7000-2121 To identi fy the co ntrol th at lowers the b o om-mou nte d cutting unit from the transport position To indicate that the cutting unit is being lowered from the transport position © ISO 2016 – All rights reserved 11 ISO 3767-3:2016(E) No 10.12 Graphical symbol ISO/IEC registration number Symbol title and description ISO 7000-0949 Grass-cutting equipment, cutting element To identi fy the control for the ho ri z o nta l ro tatio n a l cutting element of grass-cutting equipment To indicate the operational status of the cutting element T h i s s y m b o l m ay b e u s e d w i th s y m b o l s fo r e n g a ge o r d i s e n g a ge e i th e r a s s e p a r ate s y m b o l s o r i n a c o m b i n e d s y m b o l E x a mp l e s o f c o m b i n e d s y m b o l s are ISO 7000-2109 (see 10.13) and ISO 7000-2110 (see 10.14) 10.13 Grass-cutting equipment, cutting element, engage ISO 7000-2109 To identi fy the control th at engage s the b l ade o r o ther grass-cutting element To indicate that the grass-cutting element is engaged (operating) 10.14 ISO 7000-2110 Grass-cutting equipment, cutting element, disengage To identi fy the control th at d i s engage s the b l ade o r other grass-cutting element To indicate that the grass-cutting element is disengaged (not operating) 10.15 Grass-cutting equipment, cutting element, height adjustment ISO 7000-0950 To identi fy the control that sets or adj u s ts the height o f the grass-cutting element, which is the distance between the rotational cutting element and the ground To indicate the height of the cutting element 10.16 Grass-cutting equipment, cutting element, height adjustment, high cut ISO 7000-3495 To identi fy the control th at s e ts o r adj u s ts the height of the high-cut position of the grass-cutting element To identi fy the control that places the cutting element of the grass-cutting equipment to the high-cut position To identi fy the h igh- c ut p o s ition o f the c utti ng element height adj u s tment control To indicate that the cutting element is in the high-cut position 10.17 Grass-cutting equipment, cutting element, height adjustment, low cut ISO 7000-3496 To identi fy the control th at s e ts o r adj u s ts the height of the low-cut position of the grass-cutting element To identi fy the control th at p l ace s the c utti ng element of the grass-cutting equipment to the low-cut position To identi fy the low- c ut p o s ition o f the c utti ng element height adj u s tment control To indicate that the cutting element is in the low-cut position 12 © ISO 2016 – All rights reserved ISO 3767-3:2016(E) No Graphical symbol 10.18 ISO/IEC registration number Symbol title and description ISO 7000-3430 Grass-cutting equipment, cylinder drive To identi fy the control for op eration o f the c yl i nder d r ive o f re el-typ e gra s s - c utti n g e qu ip ment To i nd ic ate the op erationa l s tatu s o f the c yl i nder d rive T h i s s y m b o l m ay b e u s e d w i th s y m b o l s fo r e n ga ge o r d i s e n ga ge e i the r a s s e p a r ate s y m b o l s o r i n a c o m b i ne d s y m b o l E x a mp l e s o f c o m b i ne d s y m b o l s are ISO 7000-3497 (see 10.19) and ISO 7000-3498 (see 10.20) 10.19 Grass-cutting equipment, cylinder drive, engage ISO 7000-3497 To identi fy the co ntrol th at engage s the c yl i nder d r ive in its normal operating direction To i nd ic ate th at the c yl i nder d r ive i s en gage d 10.20 Grass-cutting equipment, cylinder drive, disengage ISO 7000-3498 To identi fy the co ntrol th at d i s en gage s the c yl i nder drive To i nd ic ate th at the c yl i nder d r ive i s d i s en gage d 10.21 Grass-cutting equipment, cylinder drive, reverse ISO 7000-3499 To identi fy the control th at re vers e s the d i re c tion o f ro tation o f the c yl i nder o f re el- typ e gra s s - c utti ng equipment To i nd ic ate th at the c yl i nder d r ive i s i n re vers e operating mode T h i s s y m b o l m ay b e u s e d w i th s y m b o l s fo r e n ga ge o r d i s e n ga ge e i th e r a s s e p a r ate s y m b o l s o r i n a c o m b i n e d s y m b o l E x a mp l e s o f c o m b i n e d s y m b o l s are ISO 7000-2111 (see 10.22) and ISO 7000-2112 (see 10.23) 10.22 Grass-cutting equipment, cylinder drive, reverse, engage ISO 7000-2111 To identi fy the control th at engage s the c yl i nder d r ive in the reverse from its normal direction of rotation To i nd ic ate th at the c yl i nder d r ive i s en gage d i n the reverse direction 10.23 Grass-cutting equipment, cylinder drive, reverse, disengage ISO 7000-2112 To identi fy the co ntrol th at d i s en gage s the c yl i nder drive from its operation in the reverse of its normal direction of rotation To i nd ic ate th at the c yl i nder d r ive i s d i s en gage d the reverse direction © ISO 2016 – All rights reserved from 13 ISO 3767-3:2016(E) No Graphical symbol 10.24 ISO/IEC registration number Symbol title and description ISO 7000-2113 Grass-cutting equipment, cylinder, on-cut adjustment To identi fy the control th at s e ts or adj u s ts the distance between the cutting blades and the strike p l ate o f a re el-typ e mower To indicate the distance between the cutting blades and the strike plate 10.25 Rotary line trimmer To identi fy the control trimmer 10.26 for ISO 7000-3431 op eratio n o f the ro ta r y l i ne ISO 7000-2592 Rotary line trimmer, output shaft speed To identi fy the control th at s e ts o r adj u s ts the ro tatio n a l s p e e d o f the output s h a ft o f the ro ta r y l i ne trimmer To indicate the output shaft speed 11 Tiller symbols No 11.1 Graphical symbol ISO/IEC registration number Symbol title and description ISO 7000-2122 Tiller tines To identi fy the control for op eratio n o f the ti ne s o f ground tilling equipment To indicate the operational status of the tiller tines 14 © ISO 2016 – All rights reserved ISO 3767-3:2016(E) 12 Snow removal equipment symbols No Graphical symbol 12 Symbol title and description ISO 7000-2123 Snow thrower, impeller To identi fy the co ntrol for ISO/IEC registration number op eration o f the i mp el ler o f a snow thrower To indicate the operational status of the impeller 12 Snow thrower, auger collector To identi fy the control for ISO 7000-2124 op eration o f the s now thrower To indicate the operational status of the collector auger T h i s s ymb ol i s the s a me a s I S O 70 0 -2 14 e xcep t th at th i s s ymb ol i s ro tate d to hor i z o nta l 12 Snow thrower, discharge chute To identi fy the control for thrower discharge chute 12 ISO 7000-3262 op eration o f the s now Snow thrower, discharge chute, height adjustment ISO 7000-3263 To identi fy the control th at adj u s ts the a n gle at wh ich the discharge chute expels snow 12 Snow thrower, discharge chute, height adjustment, up ISO 7000-2125 To identi fy the co ntrol th at i nc re a s e s the a ngle at which the discharge chute expels snow To indicate that the discharge chute is being adj u s te d up wa rd 12 Snow thrower, discharge chute, height adjustment, down ISO 7000-2126 To identi fy the co ntrol th at de c re a s e s the a ngle at which the discharge chute expels snow To i nd ic ate th at the d i s ch a rge chute i s b ei ng adj u s te d downward 12 Snow thrower, discharge chute, rotate left ISO 7000-2127 To identi fy the control th at ro tate s the d i s ch a rge chute to expel snow to the left of the snow thrower Arrow indicating rotation of the discharge chute is viewed from the perspective of a person looking at the discharge chute from above the machine 12 Snow thrower, discharge chute, rotate right ISO 7000-2128 To identi fy the control th at ro tate s the d i s ch a rge chute to expel snow to the right of the snow thrower Arrow indicating rotation of the discharge chute is viewed from the perspective of a person looking at the discharge chute from above the machine © ISO 2016 – All rights reserved 15 ISO 3767-3:2016(E) Bibliography [1] [2] [3] [4] [5] [6] ISO 3767-2, Tractors, machinery for agriculture and forestry, powered lawn and garden equipment — Symbols for operator controls and other displays—Part 2: Symbols for agricultural tractors and machinery ISO 3767-4, Tractors, machinery for agriculture and forestry, powered lawn and garden equipment — Symbols for operator controls and other displays — Part 4: Symbols for forestry machinery ISO 3767-5, Tractors, machinery for agriculture and forestry, powered lawn and garden equipment — Symbols for operator controls and other displays — Part 5: Symbols for manual portable forestry machines ISO 7000, 1) Graphical symbols for use on equipment — Registered symbols ISO 80416-4, Basic principles for graphical symbols for use on equipment — Part 4: Guidelines for the adaptation of graphical symbols for use on screens and displays (icons) IEC 60417,1) Graphical symbols for use on equipment 1) f Browsing Platform (OBP), www.iso.org/obp The grap hical symb o l co llectio ns o 16 I S O 0 and I E C 41 can b e p reviewed and p urchas ed o n the O nline © ISO 2016 – All rights reserved