Microsoft Word C033398e doc Reference number ISO 104 2002(E) © ISO 2002 INTERNATIONAL STANDARD ISO 104 Third edition 2002 02 01 Rolling bearings — Thrust bearings — Boundary dimensions, general plan R[.]
ISO 104 INTERNATIONAL STANDARD Third edition 2002-02-01 Rolling bearings — Thrust bearings — Boundary dimensions, general plan Roulements — Butées — Dimensions d'encombrement, plan général Reference number ISO 104:2002(E) `,,`,-`-`,,`,,`,`,,` - Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS Not for Resale © ISO 2002 ISO 104:2002(E) PDF disclaimer This PDF file may contain embedded typefaces In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy The ISO Central Secretariat accepts no liability in this area Adobe is a trademark of Adobe Systems Incorporated Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing Every care has been taken to ensure that the file is suitable for use by ISO member bodies In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below © ISO 2002 All rights reserved Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyright@iso.ch Web www.iso.ch Printed in Switzerland `,,`,-`-`,,`,,`,`,,` - ii Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS © ISO 2002 – All rights reserved Not for Resale ISO 104:2002(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies) The work of preparing International Standards is normally carried out through ISO technical committees Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part The main task of technical committees is to prepare International Standards Draft International Standards adopted by the technical committees are circulated to the member bodies for voting Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of patent rights ISO shall not be held responsible for identifying any or all such patent rights ISO 104 was prepared by Technical Committee ISO/TC 4, Rolling bearings This third edition cancels and replaces the second edition (ISO 104:1994) The changes are editorial in order to bring content, terminology and presentation in line with ISO Directives, Part 3, 1997 Annex A of this International Standard is for information only `,,`,-`-`,,`,,`,`,,` - iii © ISO 2002 –forAll rights reserved Copyright International Organization Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS Not for Resale `,,`,-`-`,,`,,`,`,,` - Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS Not for Resale INTERNATIONAL STANDARD ISO 104:2002(E) Rolling bearings — Thrust bearings — Boundary dimensions, general plan Scope This International Standard specifies the major boundary dimensions of single-direction and double-direction thrust bearings with flat back faces In addition, it gives the minimum bore diameters of housing washers and maximum outside diameters of shaft washers of bearings in dimension series 11, 12, 13, 14, 22, 23 and 24 Guidelines for the extension of this International Standard for single-direction thrust bearings are given in annex A Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this International Standard For dated references, subsequent amendments to, or revisions of, any of these publications not apply However, parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below For undated references, the latest edition of the normative document referred to applies Members of ISO and IEC maintain registers of currently valid International Standards ISO 582:1995, Rolling bearings — Chamfer dimensions — Maximum values ISO 1132-1:2000, Rolling bearings — Tolerances — Part 1: Terms and definitions ISO 5593:1997, Rolling bearings — Vocabulary `,,`,-`-`,,`,,`,`,,` - ISO 15241:2001, Rolling bearings — Symbols for quantities Terms and definitions For the purposes of this International Standard, the terms and definitions given in ISO 1132-1, ISO 5593 and ISO 15241 apply © ISO 2002 – All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS Not for Resale ISO 104:2002(E) Symbols height of central shaft washer D outside diameter of housing washer D1 bore diameter of housing washer D1s smallest single bore diameter of housing washer d bore diameter of shaft washer, single-direction bearing d1 outside diameter of shaft washer, single-direction bearing d1s max largest single outside diameter of shaft washer d2 bore diameter of central shaft washer, double-direction bearing d3 outside diameter of central shaft washer, double-direction bearing d3s max largest single outside diameter of central shaft washer r back face chamfer dimension of shaft washer (single-direction bearing) and housing washer rs smallest single back face chamfer dimension of shaft washer (single-direction bearing) and housing washer r1 face chamfer dimension of central shaft washer r1s smallest single face chamfer dimension of central shaft washer T bearing height, single-direction bearing T1 bearing height, double-direction bearing 5.1 `,,`,-`-`,,`,,`,`,,` - B Boundary dimensions General The symbols shown in Figures and and the values given in Tables to denote nominal dimensions unless specified otherwise The corresponding largest single chamfer dimensions to the rs and r1s dimensions in Tables to are given in ISO 582 The exact shape of the chamfer surface is not specified, but its contour in an axial plane shall not be allowed to project beyond an imaginary circular arc, of radius rs min, tangential to the washer back face and the bore or outside cylindrical surface of the washer For the washer face and the bore cylindrical surface, the same applies to r1s Chamfer dimensions r and r1 apply only at the corners indicated in Figures and No dimensions are given for other corners, however, they should not be sharp Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS © ISO 2002 – All rights reserved Not for Resale ISO 104:2002(E) 5.2 Single-direction thrust bearings Dimensions represented in Figure shall be as given in Tables to Figure — Single-direction thrust bearing 5.3 Double-direction thrust bearings Dimensions represented in Figure shall be as given in Tables to Figure — Double-direction thrust bearing `,,`,-`-`,,`,,`,`,,` - © ISO 2002 –forAll rights reserved Copyright International Organization Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS Not for Resale ISO 104:2002(E) Table — Single-direction bearings — Diameter series Dimensions in millimetres Dimensions in millimetres Dimension series D rs 70 90 10 12 12 16 18 20 22 0,3 0,3 0,3 0,3 0,3 5 5 15 17 20 25 30 26 28 32 37 42 0,3 0,3 0,3 0,3 0,3 35 40 45 50 55 47 52 60 65 70 60 65 70 75 80 Dimension series 10 d D rs 70 90 — — — — — 7 7 460 480 500 530 560 500 520 540 580 610 1 1,1 1,1 18 18 18 23 23 24 24 24 30 30 30 30 30 38 38 5 6 — — — — — 7 8 600 630 670 710 750 650 680 730 780 820 1,1 1,1 1,5 1,5 1,5 23 23 27 32 32 30 30 36 42 42 38 38 45 53 53 0,3 0,3 0,3 0,3 0,3 6 7 — — — — — 10 10 10 800 850 900 950 000 870 920 980 030 090 1,5 1,5 2 2,1 32 32 36 36 41 42 42 48 48 54 53 53 63 63 70 75 80 85 90 95 0,3 0,3 0,3 0,3 0,3 7 7 — — — — — 10 10 10 10 10 060 120 180 250 320 150 220 280 360 440 2,1 2,1 2,1 3 41 45 45 50 — 54 60 60 67 — 70 80 80 85 95 85 90 100 110 120 100 105 120 130 140 0,3 0,3 0,6 0,6 0,6 7 9 — — — — — 10 10 14 14 14 400 500 600 700 800 520 630 730 840 950 4 4 — — — — — — — — — — 95 105 105 112 120 130 140 150 160 170 150 160 170 180 190 0,6 0,6 0,6 0,6 0,6 9 9 — — — — — 14 14 14 14 14 900 000 120 240 360 060 160 300 430 550 5 5 — — — — — — — — — — 130 130 140 150 150 180 190 200 220 240 200 215 225 250 270 0,6 1 1 11 11 14 14 — — — — — 14 17 17 22 22 500 700 — — 160 260 280 300 320 340 290 310 340 360 380 1 1 14 14 18 18 18 — — 24 24 24 22 22 30 30 30 360 380 400 420 440 400 420 440 460 480 1 1 18 18 18 18 18 24 24 24 24 24 30 30 30 30 30 T T Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS 10 © ISO 2002 – All rights reserved Not for Resale `,,`,-`-`,,`,,`,`,,` - d ISO 104:2002(E) Table — Single-direction bearings — Diameter series Dimensions in millimetres Dimensions in millimetres Dimension series Dimension series d D rs 71 91 d D rs 71 91 d1s max D1s 10 12 15 17 20 24 26 28 30 35 0,3 0,3 0,3 0,3 0,3 6 6 — — — — — 9 9 10 24 26 28 30 35 d1s max D1s 11 13 16 18 21 530 560 600 630 670 640 670 710 750 800 3 3 50 50 50 54 58 67 67 67 73 78 85 85 85 95 105 635 665 705 745 795 534 564 604 634 674 25 30 35 40 45 42 47 52 60 65 0,6 0,6 0,6 0,6 0,6 8 9 — — — — — 11 11 12 13 14 42 47 52 60 65 26 32 37 42 47 710 750 800 850 900 850 900 950 000 060 4 4 63 67 67 67 73 85 90 90 90 95 112 120 120 120 130 845 895 945 995 055 714 755 805 855 905 50 55 60 65 70 70 78 85 90 95 0,6 0,6 1 10 11 11 11 — — — — — 14 16 17 18 18 70 78 85 90 95 52 57 62 67 72 950 000 060 120 180 120 180 250 320 400 5 5 78 82 85 90 100 103 109 115 122 132 135 140 150 160 175 115 175 245 315 395 955 005 065 125 185 75 80 85 90 100 100 105 110 120 135 1 1 11 11 11 14 16 — — — — 21 19 19 19 22 25 100 105 110 120 135 77 82 87 92 102 250 320 400 500 600 460 540 630 750 850 6 6 — — — — — — — — — — 175 175 180 195 195 455 535 620 740 840 255 325 410 510 610 110 120 130 140 150 145 155 170 180 190 1 1 16 16 18 18 18 21 21 24 24 24 25 25 30 31 31 145 155 170 178 188 112 122 132 142 152 700 800 900 000 120 970 080 180 300 430 7,5 7,5 7,5 7,5 7,5 — — — — — — — — — — 212 220 220 236 243 960 070 170 290 420 710 810 910 010 130 160 170 180 190 200 200 215 225 240 250 1,1 1,1 1,1 1,1 18 20 20 23 23 24 27 27 30 30 31 34 34 37 37 198 213 222 237 247 162 172 183 193 203 240 360 500 570 700 850 9,5 9,5 9,5 — — — — — — 258 265 272 560 690 840 250 370 510 220 240 260 280 300 270 300 320 350 380 1,1 1,5 1,5 1,5 23 27 27 32 36 30 36 36 42 48 37 45 45 53 62 267 297 317 347 376 223 243 263 283 304 320 340 360 380 400 400 420 440 460 480 2 2 36 36 36 36 36 48 48 48 48 48 63 64 65 65 65 396 416 436 456 476 324 344 364 384 404 420 440 460 480 500 500 540 560 580 600 2,1 2,1 2,1 2,1 36 45 45 45 45 48 60 60 60 60 65 80 80 80 80 495 535 555 575 595 424 444 464 484 504 11 T T `,,`,-`-`,,`,,`,`,,` - © ISO 2002 – All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS 11 Not for Resale ISO 104:2002(E) Table — Single-direction bearings — Diameter series Dimensions in millimetres Dimensions in millimetres Dimension series Dimension series d D rs 72 92 d D rs 72 92 d1s max D1s 10 12 16 20 22 26 28 0,3 0,3 0,3 0,6 0,6 6 7 — — — — — 9 11 11 16 20 22 26 28 d1s max D1s 12 14 460 480 500 530 560 620 650 670 710 750 5 5 73 78 78 82 85 95 103 103 109 115 130 135 135 140 150 615 645 665 705 745 465 485 505 535 565 15 17 20 25 30 32 35 40 47 52 0,6 0,6 0,6 0,6 0,6 8 10 10 — — — — — 12 12 14 15 16 32 35 40 47 52 17 19 22 27 32 600 630 670 710 750 800 850 900 950 000 6 6 90 100 103 109 112 122 132 140 145 150 160 175 180 190 195 795 845 895 945 995 605 635 675 715 755 35 40 45 50 55 62 68 73 78 90 1 1 12 13 13 13 16 — — — — 21 18 19 20 22 25 62 68 73 78 90 37 42 47 52 57 800 850 900 950 000 060 120 180 250 320 7,5 7,5 7,5 7,5 9,5 118 122 125 136 145 155 160 170 180 190 205 212 220 236 250 055 115 175 245 315 805 855 905 955 005 60 65 70 75 80 95 100 105 110 115 1 1 16 16 16 16 16 21 21 21 21 21 26 27 27 27 28 95 100 105 110 115 62 67 72 77 82 060 120 180 250 320 400 460 520 610 700 9,5 9,5 9,5 9,5 9,5 155 — — — — 206 206 206 216 228 265 — — — — 395 — — — — 065 — — — — 85 90 100 110 120 125 135 150 160 170 1,1 1,1 1,1 1,1 18 20 23 23 23 24 27 30 30 30 31 35 38 38 39 125 135 150 160 170 88 93 103 113 123 400 500 600 700 800 790 920 040 160 280 12 12 15 15 15 — — — — — 234 252 264 276 288 — — — — — — — — — — — — — — — 130 140 150 160 170 190 200 215 225 240 1,5 1,5 1,5 1,5 1,5 27 27 29 29 32 36 36 39 39 42 45 46 50 51 55 187 197 212 222 237 133 143 153 163 173 180 190 200 220 240 250 270 280 300 340 1,5 2 2,1 32 36 36 36 45 42 48 48 48 60 56 62 62 63 78 247 267 277 297 335 183 194 204 224 244 260 280 300 320 340 360 380 420 440 460 2,1 2,1 3 45 45 54 54 54 60 60 73 73 73 79 80 95 95 96 355 375 415 435 455 264 284 304 325 345 360 380 400 420 440 500 520 540 580 600 4 5 63 63 63 73 73 85 85 85 95 95 110 112 112 130 130 495 515 535 575 595 365 385 405 425 445 12 T T `,,`,-`-`,,`,,`,`,,` - Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS 12 © ISO 2002 – All rights reserved Not for Resale ISO 104:2002(E) Table — Single-direction bearings — Diameter series Dimensions in millimetres Dimensions in millimetres Dimension series Dimension series d D rs 73 93 d D rs 73 93 d1s max D1s 10 12 20 24 26 30 32 0,6 0,6 0,6 0,6 0,6 8 9 — — — — — 11 12 12 14 14 20 24 26 30 32 d1s max D1s 10 12 460 480 500 530 560 710 730 750 800 850 6 7,5 7,5 112 112 112 122 132 150 150 150 160 175 195 195 195 212 224 705 725 745 795 845 465 485 505 535 565 15 17 20 25 30 37 40 47 52 60 0,6 0,6 1 10 10 12 12 14 — — — — — 15 16 18 18 21 37 40 47 52 60 15 19 22 27 32 600 630 670 710 750 900 950 000 060 120 7,5 9,5 9,5 9,5 9,5 136 145 150 160 165 180 190 200 212 224 236 250 258 272 290 895 945 995 055 115 605 635 675 715 755 35 40 45 50 55 68 78 85 95 105 1 1,1 1,1 15 17 18 20 23 — 22 24 27 30 24 26 28 31 35 68 78 85 95 105 37 42 47 52 57 800 850 900 950 000 180 250 320 400 460 9,5 12 12 12 12 170 180 190 200 — 230 243 250 272 276 300 315 335 355 — 175 245 315 395 — 805 855 905 955 — 60 65 70 75 80 110 115 125 135 140 1,1 1,1 1,1 1,5 1,5 23 23 25 27 27 30 30 34 36 36 35 36 40 44 44 110 115 125 135 140 62 67 72 77 82 060 120 180 250 320 540 630 710 800 900 15 15 15 19 19 — — — — — 288 306 318 330 348 — — — — — — — — — — — — — — — 85 90 100 110 120 150 155 170 190 210 1,5 1,5 1,5 2,1 29 29 32 36 41 39 39 42 48 54 49 50 55 63 70 150 155 170 187 205 88 93 103 113 123 400 500 600 000 140 270 19 19 19 — — — 360 384 402 — — — — — — — — — 130 140 150 160 170 225 240 250 270 280 2,1 2,1 2,1 3 42 45 45 50 50 58 60 60 67 67 75 80 80 87 87 220 235 245 265 275 134 144 154 164 174 180 190 200 220 240 300 320 340 360 380 4 4 54 58 63 63 63 73 78 85 85 85 95 105 110 112 112 295 315 335 355 375 184 195 205 225 245 260 280 300 320 340 420 440 480 500 540 5 5 73 73 82 82 90 95 95 109 109 122 130 130 140 140 160 415 435 475 495 535 265 285 305 325 345 360 380 400 420 440 560 600 620 650 680 6 6 90 100 100 103 109 122 132 132 140 145 160 175 175 180 190 555 595 615 645 675 365 385 405 425 445 13 T `,,`,-`-`,,`,,`,`,,` - T © ISO 2002 – All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS 13 Not for Resale ISO 104:2002(E) Table — Single-direction bearings — Diameter series Dimensions in millimetres Dimensions in millimetres Dimension series d D rs 74 Dimension series d 94 14 T d1s max D1s D rs 74 94 14 T d1s max D1s 25 30 35 40 45 60 70 80 90 100 1 1,1 1,1 1,1 16 18 20 23 25 21 24 27 30 34 24 28 32 36 39 60 70 80 90 100 27 32 37 42 47 670 710 750 800 850 150 220 280 360 440 15 15 15 15 15 218 230 236 250 — 290 308 315 335 354 375 400 412 438 — 145 215 275 355 — 675 715 755 805 — 50 55 60 65 70 110 120 130 140 150 1,5 1,5 1,5 2 27 29 32 34 36 36 39 42 45 48 43 48 51 56 60 110 120 130 140 150 52 57 62 68 73 900 950 000 060 120 520 600 670 770 860 15 15 15 15 15 — — — — — 372 390 402 426 444 — — — — — — — — — — — — — — — 75 80 85 90 100 160 170 180 190 210 2,1 2,1 2,1 38 41 42 45 50 51 54 58 60 67 65 68 72 77 85 160 170 177 187 205 78 83 88 93 103 180 250 320 400 950 050 160 280 19 19 19 19 — — — — 462 480 505 530 — — — — — — — — — — — — 110 120 130 140 150 230 250 270 280 300 4 4 54 58 63 63 67 73 78 85 85 90 95 102 110 112 120 225 245 265 275 295 113 123 134 144 154 160 170 180 190 200 320 340 360 380 400 5 5 73 78 82 85 90 95 103 109 115 122 130 135 140 150 155 315 335 355 375 395 164 174 184 195 205 220 240 260 280 420 440 480 520 6 6 90 90 100 109 122 122 132 145 160 160 175 190 415 435 475 515 225 245 265 285 300 320 340 360 380 540 580 620 640 670 7,5 7,5 7,5 7,5 109 118 125 125 132 145 155 170 170 175 190 205 220 220 224 535 575 615 635 665 305 325 345 365 385 400 420 440 460 480 710 730 780 800 850 7,5 7,5 9,5 9,5 9,5 140 140 155 155 165 185 185 206 206 224 243 243 265 265 290 705 725 775 795 845 405 425 445 465 485 500 530 560 600 630 870 920 980 030 090 9,5 9,5 12 12 12 165 175 190 195 206 224 236 250 258 280 290 308 335 335 365 865 915 975 025 085 505 535 565 605 635 Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS `,,`,-`-`,,`,,`,`,,` - Not for Resale © ISO 2002 – All rights reserved ISO 104:2002(E) Table — Single-direction bearings — Diameter series Dimensions in millimetres Dimensions in millimetres Dimension series d D rs Dimension series d 95 D rs T 52 60 73 85 100 1 1,1 1,1 1,1 21 24 29 34 39 40 45 50 55 60 110 120 135 150 160 1,5 2 2,1 2,1 42 45 51 58 60 65 70 75 80 85 170 180 190 200 215 2,1 3 63 67 69 73 78 90 100 110 120 130 225 250 270 300 320 4 5 82 90 95 109 115 140 150 160 170 340 360 380 400 6 122 125 132 140 180 190 200 220 240 420 440 460 500 540 6 7,5 7,5 7,5 145 150 155 170 180 260 280 300 320 340 580 620 670 710 750 9,5 9,5 9,5 9,5 12 190 206 224 236 243 360 380 400 420 440 780 820 850 900 950 12 12 12 15 15 250 265 272 290 308 460 480 500 530 560 980 000 060 090 150 15 15 15 15 15 315 315 335 335 355 T 600 630 670 710 15 15 15 15 375 388 388 412 © ISO 2002 – All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS 220 280 320 400 `,,`,-`-`,,`,,`,`,,` - 17 20 25 30 35 95 Not for Resale ISO 104:2002(E) Table — Double-direction bearings — Diameter series — Dimension series 22 Dimensions in millimetres d2 da D rs r1s T1 B d3s max D1s 10 15 20 25 30 15 20 25 30 35 32 40 47 52 62 0,6 0,6 0,6 0,6 0,3 0,3 0,3 0,3 0,3 22 26 28 29 34 7 32 40 47 52 62 17 22 27 32 37 30 35 40 45 50 40 45 50 55 60 68 73 78 90 95 1 1 0,6 0,6 0,6 0,6 0,6 36 37 39 45 46 9 10 10 68 73 78 90 95 42 47 52 57 62 55 55 60 65 70 65 70 75 80 85 100 105 110 115 125 1 1 0,6 1 1 47 47 47 48 55 10 10 10 10 12 100 105 110 115 125 67 72 77 82 88 75 85 95 100 110 90 100 110 120 130 135 150 160 170 190 1,1 1,1 1,1 1,1 1,5 1 1,1 1,1 62 67 67 68 80 14 15 15 15 18 135 150 160 170 189,5 93 103 113 123 133 120 130 140 150 150 140 150 160 170 180 200 215 225 240 250 1,5 1,5 1,5 1,5 1,5 1,1 1,1 1,1 1,1 81 89 90 97 98 18 20 20 21 21 199,5 214,5 224,5 239,5 249 143 153 163 173 183 160 170 190 190 200 220 270 280 300 2 2 2 109 109 110 24 24 24 269 279 299 194 204 224 a d is the bore diameter of shaft washer of corresponding diameter series 2, single-direction bearing, given in Table `,,`,-`-`,,`,,`,`,,` - 10 Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS © ISO 2002 – All rights reserved Not for Resale ISO 104:2002(E) Table — Double-direction bearings — Diameter series — Dimension series 23 Dimensions in millimetres d2 da D rs r1s T1 B d3s max D1s 20 25 30 30 35 25 30 35 40 45 52 60 68 78 85 1 1 0,3 0,3 0,3 0,6 0,6 34 38 44 49 52 10 12 12 52 60 68 78 85 27 32 37 42 47 40 45 50 55 55 50 55 60 65 70 95 105 110 115 125 1,1 1,1 1,1 1,1 1,1 0,6 0,6 0,6 0,6 58 64 64 65 72 14 15 15 15 16 95 105 110 115 125 52 57 62 67 72 60 65 70 75 85 75 80 85 90 100 135 140 150 155 170 1,5 1,5 1,5 1,5 1,5 1 1 79 79 87 88 97 18 18 19 19 21 135 140 150 155 170 77 82 88 93 103 95 100 110 120 130 110 120 130 140 150 190 210 225 240 250 2,1 2,1 2,1 2,1 1,1 1,1 1,1 1,1 110 123 130 140 140 24 27 30 31 31 189,5 209,5 224 239 249 113 123 134 144 154 140 150 150 160 170 160 170 180 190 200 270 280 300 320 340 3 4 1,1 1,1 2 153 153 165 183 192 33 33 37 40 42 269 279 299 319 339 164 174 184 195 205 `,,`,-`-`,,`,,`,`,,` - a d is the bore diameter of shaft washer of corresponding diameter series 3, single-direction bearing, given in Table 11 © ISO 2002 – All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS Not for Resale ISO 104:2002(E) Table — Double-direction bearings — Diameter series — Dimension series 24 Dimensions in millimetres d2 da D rs r1s T1 B d3s max D1s 15 20 25 30 35 25 30 35 40 45 60 70 80 90 100 1 1,1 1,1 1,1 0,6 0,6 0,6 0,6 0,6 45 52 59 65 72 11 12 14 15 17 60 70 80 90 100 27 32 37 42 47 40 45 50 50 55 50 55 60 65 70 110 120 130 140 150 1,5 1,5 1,5 2 0,6 0,6 0,6 1 78 87 93 101 107 18 20 21 23 24 110 120 130 140 150 52 57 62 68 73 60 65 65 70 80 75 80 85 90 100 160 170 180 190 210 2,1 2,1 2,1 1 1,1 1,1 1,1 115 120 128 135 150 26 27 29 30 33 160 170 179,5 189,5 209,5 78 83 88 93 103 90 95 100 110 120 110 120 130 140 150 230 250 270 280 300 4 4 1,1 1,5 2 166 177 192 196 209 37 40 42 44 46 229 249 269 279 299 113 123 134 144 154 130 135 140 160 170 180 320 340 360 5 2,1 226 236 245 50 50 52 319 339 359 164 174 184 a d is the bore diameter of shaft washer of corresponding diameter series 4, single-direction bearing, given in Table `,,`,-`-`,,`,,`,`,,` - 12 Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS © ISO 2002 – All rights reserved Not for Resale ISO 104:2002(E) Annex A (informative) Guidelines for the extension of this International Standard for single-direction thrust bearings A.1 General For any new dimension not numerically determined in this International Standard, the following guidelines should be used The formulae given for outside diameter and height should not, however, be used for definite determination of the boundary dimension values; they may often require to be modified in order to maintain the continuity of this International Standard to obtain suitable bearing proportions, and to permit selection of preferred dimensions Accordingly, any new dimensions will have to be approved by ISO A.2 Bore diameters Bore diameters, d, of shaft washers, above d = 500 mm, should be selected from the R 40 series of preferred numbers given in ISO A.3 Outside diameters Outside diameters, D, of housing washers should be calculated, in millimetres, from the formula: D = d + fD d 0,8 where the factor fD has the appropriate value given in Table A.1 Table A.1 — Values of fD Diameter series fD 0,36 0,72 1,2 1,84 2,68 3,8 Outside diameter dimensions already appearing in this International Standard should be chosen for preference New outside diameter dimensions should be rounded as shown in Table A.2 Table A.2 — Rounding for D D mm Rounded to the nearest > u — 0,5 mm 80 mm 80 230 mm 230 — 10 mm `,,`,-`-`,,`,,`,`,,` - 13 © ISO 2002 –forAll rights reserved Copyright International Organization Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS Not for Resale ISO 104:2002(E) A.4 Bearing heights Bearing heights, T, should be calculated, in millimetres, using the formula: T = fT D−d where the factor fT has the appropriate value in Table A.3 Table A.3 — Values of fT Height series fT 0,9 1,2 1,6 New height dimensions should be rounded as shown in Table A.4 Table A.4 — Rounding for T T mm > Rounded to the nearest u — 0,1 mm 0,5 mm 500 mm 500 — mm Smallest single chamfer dimension rs should be selected from the rs values listed in ISO 582 and, in principle, be that value which is nearest to, but not larger than the smaller of the two values: % of the height T and % of the sectional width (D – d)/2 14 Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS © ISO 2002 – All rights reserved Not for Resale `,,`,-`-`,,`,,`,`,,` - A.5 Smallest single chamfer dimension ISO 104:2002(E) Bibliography [1] ISO 3:1973, Preferred numbers — Series of preferred numbers `,,`,-`-`,,`,,`,`,,` - 15 © ISO 2002 –forAll rights reserved Copyright International Organization Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS Not for Resale ISO 104:2002(E) ICS 21.100.20 Price based on 15 pages © ISO 2002 – All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO No reproduction or networking permitted without license from IHS `,,`,-`-`,,`,,`,`,,` - Not for Resale