1. Trang chủ
  2. » Kỹ Thuật - Công Nghệ

WT mâm XE và vỏ XE TRÊN NISSAN VERSA SEDAN 2012

45 407 0

Đang tải... (xem toàn văn)

Tài liệu hạn chế xem trước, để xem đầy đủ mời bạn chọn Tải xuống

THÔNG TIN TÀI LIỆU

Thông tin cơ bản

Định dạng
Số trang 45
Dung lượng 1,11 MB

Nội dung

MÂM XE VÀ VỎ XE TRÊN NISSAN VERSA SEDAN ĐỜI 2012

Trang 1

C

D

F

G

H

I

J

K

L

M

B

WT

N

O

P

CONTENTS

ROAD WHEELS & TIRES

PRECAUTION 3

PRECAUTIONS 3

Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TEN-SIONER" 3

Service Notice and Precautions for TPMS 3

Service Notice and Precautions for Road Wheel 3

PREPARATION 5

PREPARATION 5

Special Service Tool .5

Commercial Service Tool .5

SYSTEM DESCRIPTION .6

COMPONENT PARTS 6

Component Parts Location 6

Component Description 6

BCM 6

Remote Keyless Entry Receiver .6

Transmitter 7

Low Tire Pressure Warning Lamp 7

SYSTEM 8

TIRE PRESSURE MONITORING SYSTEM 8

TIRE PRESSURE MONITORING SYSTEM : Sys-tem Diagram 8

TIRE PRESSURE MONITORING SYSTEM : Sys-tem Description .8

DIAGNOSIS SYSTEM (BCM) 9

COMMON ITEM 9

COMMON ITEM : CONSULT Function (BCM - COMMON ITEM) 9

AIR PRESSURE MONITOR 10

AIR PRESSURE MONITOR : CONSULT Function (BCM - AIR PRESSURE MONITOR) 10

AIR PRESSURE MONITOR : Self Diagnosis With-out CONSULT .11

ECU DIAGNOSIS INFORMATION 14

BCM 14

List of ECU Reference 14

WIRING DIAGRAM 15

TIRE PRESSURE MONITORING SYSTEM 15

Wiring Diagram 15

BASIC INSPECTION .19

DIAGNOSIS AND REPAIR WORK FLOW 19

Work Flow 19

TRANSMITTER WAKE UP OPERATION 20

Description 20

Work Procedure 20

ID REGISTRATION PROCEDURE 21

Description 21

Work Procedure 21

DTC/CIRCUIT DIAGNOSIS .23

C1704, C1705, C1706, C1707 LOW TIRE PRESSURE 23

DTC Logic 23

Diagnosis Procedure .23

C1708, C1709, C1710, C1711 TRANSMITTER (NO DATA) 24

DTC Logic 24

Diagnosis Procedure .24

C1716, C1717, C1718, C1719 TRANSMITTER (PRESSURE DATA) 27

DTC Logic 27

Diagnosis Procedure .27

Trang 2

C1729 VEHICLE SPEED SIGNAL 28

DTC Logic 28

Diagnosis Procedure .28

LOW TIRE PRESSURE WARNING LAMP 29

Component Function Check .29

Diagnosis Procedure .29

POWER SUPPLY AND GROUND CIRCUIT 30

Diagnosis Procedure .30

SYMPTOM DIAGNOSIS .31

TPMS SYMPTOMS 31

Symptom Table .31

LOW TIRE PRESSURE WARNING LAMP DOES NOT TURN ON 32

Diagnosis Procedure .32

LOW TIRE PRESSURE WARNING LAMP DOES NOT TURN OFF 33

Diagnosis Procedure .33

LOW TIRE PRESSURE WARNING LAMP BLINKS 34

Diagnosis Procedure .34

ID REGISTRATION CANNOT BE COMPLET-ED 35

Diagnosis Procedure 35

NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING 36

NVH Troubleshooting Chart 36

PERIODIC MAINTENANCE 37

ROAD WHEEL 37

Inspection 37

REMOVAL AND INSTALLATION 38

ROAD WHEEL TIRE ASSEMBLY 38

Adjustment 38

TRANSMITTER 41

Exploded View .41

Removal and Installation 41

TIRE PRESSURE RECEIVER 44

Removal and Installation 44

SERVICE DATA AND SPECIFICATIONS (SDS) 45

SERVICE DATA AND SPECIFICATIONS (SDS) 45

Road Wheel .45

Tire Air Pressure .45

Trang 3

Information necessary to service the system safely is included in the SR and SB section of this Service ual.

Man-WARNING:

• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in the event of a collision which would result in air bag inflation, all maintenance must be performed by

an authorized NISSAN/INFINITI dealer.

• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system For removal of Spiral Cable and Air Bag Module, see the SR section.

• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual SRS wiring harnesses can be identified by yellow and/or orange harnesses or har- ness connectors.

PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS

WARNING:

• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a hammer Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing serious injury.

Igni-• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the battery, and wait at least 3 minutes before performing any service.

• Low tire pressure warning lamp blinks for 1 minute, then turns ON when occurring any malfunction exceptlow tire pressure Erase the self-diagnosis memories for Tire Pressure Monitoring System (TPMS), or regis-ter the ID to turn low tire pressure warning lamp OFF For ID registration, refer to WT-21, "Work Procedure"

• ID registration is required when replacing or rotating wheels, replacing tire pressure sensor or BCM Refer to

WT-21, "Work Procedure"

• Replace grommet seal, valve core and valve cap of tire pressure sensor in TPMS, when replacing each tire

by reaching the wear limit Refer to WT-41, "Removal and Installation"

• Because the tire pressure sensor conforms to North America radio law, the following items must beobserved

- The sensor may be used only in North America

- It may not be used in any method other than the specified method

- It must not be disassembled or modified

• Genuine NISSAN aluminum wheel is designed for each type of vehicle Use it on the specified vehicle only

• Use Genuine NISSAN parts for the road wheels, valve caps and wheel nuts

• Always use them after adjusting the wheel balance For the balance weights, use Genuine NISSAN num wheel weights

alumi-• Use caution when handling the aluminum wheels, because they can be easily scratched When removingdirt, do not use any abrasives, a wire brush, or other items that may scratch the coating Use a neutral deter-gent if a detergent is needed

• After driving on roads scattered with anti-icing salts, wash off the wheels completely

Trang 4

< PRECAUTION >

PRECAUTIONS

• Never apply oil to nut and bolt threads

• When tightening the valve cap there is a risk of damaging the valve cap if a tool is used Tighten by hand

Trang 5

The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.

Transmitter activation tool

• Transmitter wake-up operation

• ID registration procedure

(J-50190)

Signal Tech II

• Activate and display TPMS transmitter IDs

• Display tire pressure reported by the TPMS transmitter

• Read TPMS DTCs

• Register TPMS transmitter IDs

• Test remote keyless entry keyfob relative signal strength

SEIA0462E

ALEIA0131ZZ

PBIC0190E

Trang 6

< SYSTEM DESCRIPTION >

COMPONENT PARTS

SYSTEM DESCRIPTION

COMPONENT PARTS

The BCM reads the tire pressure signal received by the remote keyless entry receiver, and controls the low tirepressure warning lamp and the buzzer operations It also has a self-diagnosis function to detect a system mal-function

The remote keyless entry receiver receives the tire pressure signal transmitted by the transmitter in eachwheel

4 Combination meter (with type B) 5 Combination meter (with type A)

BCM WT-6, "BCM"

Remote keyless entry receiver WT-6, "Remote Keyless Entry Receiver"

Transmitter WT-7, "Transmitter"

Low tire pressure warning lamp WT-8, "TIRE PRESSURE MONITORING SYSTEM : System Description"

Combination meter Transmits the vehicle speed signal via CAN communication to BCM.

Receives the low tire pressure warning lamp signal via CAN communication from BCM.

Trang 7

The combination meter receives tire pressure status from the BCM using CAN communication When a lowtire pressure condition is sensed by the BCM, the combination meter low tire pressure warning lamp is acti-vated.

Trang 8

< SYSTEM DESCRIPTION >

SYSTEM

SYSTEM

TIRE PRESSURE MONITORING SYSTEM

• The BCM has pressure judgment and trouble diagnosis functions When the BCM detects low inflation sure or another unusual symptom, the low tire pressure warning lamp in the combination meter is illumi-nated

pres-• If the tire pressure is less than the specified value, the low tire pressure warning lamp illuminates

• The TPMS (Tire Pressure Monitoring System) is activated when vehicle speed is 40 km/h (25 MPH) or more

INPUT/OUTPUT SIGNAL

LOW TIRE PRESSURE WARNING LAMP CONTROL CONDITION

The BCM uses CAN communication to illuminate the low tire pressure warning lamp in the combination meter

ALEIA0133GB

Component Signal Description

BCM Transmits the low tire pressure warning lamp signal via CAN communication to combination meter.Combination meter Transmits the vehicle speed signal via CAN communication to BCM.

Condition Low tire pressure warning lamp

Ignition switch ON (system normal) Warning light turns on for 1second, then turns off.

Low tire pressure

ON Transmitter ID not registered in BCM.

Tire pressure monitoring system malfunction Warning light blinks 1 minute, then turns on.

Tire pressure sensor is in OFF state (Blinking pattern depends on the positions of nonoperational tire pressure sensors.)Blink

Trang 9

BCM can perform the following functions.

Direct Diagnostic Mode Description

ECU identification The BCM part number is displayed.

Self Diagnostic Result The BCM self diagnostic results are displayed.

Data Monitor The BCM input/output data is displayed in real time.

Active Test The BCM activates outputs to test components.

Work support The settings for BCM functions can be changed.

Configuration • The vehicle specification can be read and saved.• The vehicle specification can be written when replacing BCM.

CAN DIAG SUPPORT MNTR The result of transmit/receive diagnosis of CAN communication is displayed.

System Sub System

Direct Diagnostic Mode

Rear window defogger REAR DEFOGGER × ×

Interior room lamp timer INT LAMP × × ×

Remote keyless entry system MULTI REMOTE ENT × × ×

Turn signal and hazard warning lamps FLASHER × ×

Air conditioner AIR CONDITIONER ×

Combination switch COMB SW ×

Interior room lamp battery saver BATTERY SAVER × × ×

Signal buffer system SIGNAL BUFFER ×

Trang 10

< SYSTEM DESCRIPTION >

DIAGNOSIS SYSTEM (BCM)

AIR PRESSURE MONITOR

AIR PRESSURE MONITOR : CONSULT Function (BCM - AIR PRESSURE

Monitor Item [Unit] Description

AIR PRESS FL [kPa, kg/cm2 or Psi] Indicates air pressure of front LH tire.

AIR PRESS FR [kPa, kg/cm2 or Psi] Indicates air pressure of front RH tire.

AIR PRESS RR [kPa, kg/cm2 or Psi] Indicates air pressure of rear RH tire.

AIR PRESS RL [kPa, kg/cm2 or Psi] Indicates air pressure of rear LH tire.

ID REGST FL1 [Done/Yet] Indicates ID registration status of front LH transmitter.

ID REGST FR1 [Done/Yet] Indicates ID registration status of front RH transmitter.

ID REGST RR1 [Done/Yet] Indicates ID registration status of rear RH transmitter.

ID REGST RL1 [Done/Yet] Indicates ID registration status of rear LH transmitter.

WARNING LAMP [Off/On] Indicates condition of low tire pressure warning lamp in combination meter.

BUZZER [Off/On] Indicates condition of buzzer in combination meter.

WARNING LAMP This test is able to check tire pressure warning lamp operation [On/Off].

ID REGIST WARNING This test is able to check ID registration warning chime operation [On/Off].

FLASHER This test is able to check turn signal lamp operation [Off/LH/RH].

Support Item Description

ID READ The registered ID number is displayed.

ID REGIST Refer to WT-21, "Description"

Trang 12

Low tire

pressure

warning

lamp

The low tire pressure

warning lamp

illumi-nates for 1 second,

then turns OFF.

Wake-up operation for all transmitters is completed.

No procedure.

(No system malfunctions)

The low tire pressure

warning lamp repeats

blinking ON for 2

sec-onds and OFF for 0.2

seconds.

Wake-up operation for all transmitters is not complet- ed.

Perform the wake-up ation for all transmitters at wheels Refer to WT-20,

oper-"Work Procedure"

The low tire pressure

warning lamp blinks

oper-WT-20, "Work Procedure"

The low tire pressure

warning lamp repeats

oper-WT-20, "Work Procedure"

The low tire pressure

warning lamp repeats

blinking for 3 times.

The rear RH wheel mitter is not activated.

trans-Perform the wake-up ation for the transmitter at rear RH wheel Refer to

oper-WT-20, "Work Procedure"

The low tire pressure

warning lamp repeats

blinking for 4 times.

The rear LH wheel ter is not activated.

transmit-Perform the wake-up ation for the transmitter at rear LH wheel Refer to WT-

oper-20, "Work Procedure"

The low tire pressure

warning lamp turns

ON and stays

illumi-nated.

Low tire pressure Check the tire pressure for

all wheels and adjust to the specified value Refer to

WT-45, "Tire Air Pressure"

Trang 13

The low tire pressure

warning lamp repeats

blinking at 0.5-second

intervals for 1 minute,

and then stays

illumi-nated.

The combination meter fuse

is open or removed (or pulled out).

Check and install the bination meter fuse If nec- essary, replace the fuse.

com-The BCM harness tor is removed.

connec-Check the connection ditions of the BCM harness connector, and repair if nec- essary.

con-Tire Pressure Monitoring System (TPMS) malfunc- tion.

• Perform self-diagnosis.

• If necessary, perform transmitter ID registra- tion Refer to WT-21,

"Work Procedure" Turn signal

lamps

The turn signal lamps

do not blink twice

when the transmitter is

when the transmitter

wake-up operation is performed.

Turn the ignition switch ON when performing the trans- mitter wake-up operation.

The activation tool 45295) is not used in the correct position.

(J-Operate the activation tool (J-45295) in the correct po- sition when performing the wake-up operation.

The transmitter is already awake.

No procedure.

Diagnosis

items

Symptom (Ignition switch ON) Low tire pressure warning lamp Cause Action

SEIA0788E

Trang 14

< ECU DIAGNOSIS INFORMATION >

Trang 15

TIRE PRESSURE MONITORING SYSTEM

TIRE PRESSURE MONITORING SYSTEM

ABEWA0069GB

Trang 16

< WIRING DIAGRAM >

TIRE PRESSURE MONITORING SYSTEM

ABEIA0117GB

Trang 17

TIRE PRESSURE MONITORING SYSTEM

Trang 18

< WIRING DIAGRAM >

TIRE PRESSURE MONITORING SYSTEM

ABEIA0119GB

Trang 19

DIAGNOSIS AND REPAIR WORK FLOW

DIAGNOSIS AND REPAIR WORK FLOW

NOTE:

The Signal Tech II Tool (J-50190) can be used to perform the following functions Refer to the Signal Tech IIUser Guide for additional information

• Activate and display TPMS transmitter IDs

• Display tire pressure reported by the TPMS transmitter

• Read TPMS DTCs

• Register TPMS transmitter IDs

Get detailed information from the customer about the symptom (the condition and the environment when theincident/malfunction occurred)

>> GO TO 2

Check the tire pressure for all wheels Refer to WT-45, "Tire Air Pressure"

Is the inspection result normal?

YES >> GO TO 3

NO >> Repair or replace tire(s) or wheel(s)

Check that the low tire pressure warning lamp illuminates for approximately 1 second after the ignition switch

is turned ON, then turns OFF

Does the low tire pressure warning lamp turn OFF?

YES >> Inspection End

NO >> GO TO 4

Perform self diagnostic result Refer to WT-10, "AIR PRESSURE MONITOR : CONSULT Function (BCM - AIRPRESSURE MONITOR)"

Are any DTCs displayed?

YES >> Refer to BCS-36, "DTC Index" If two or more DTCs are displayed, refer to BCS-35,

"DTC Inspection Priority Chart"

NO >> GO TO 5

Perform diagnosis applicable to the symptom Refer to WT-31, "Symptom Table"

>> GO TO 6

Perform self diagnostic result again, and check that the malfunction is repaired After checking, erase the selfdiagnosis memory Refer to WT-10, "AIR PRESSURE MONITOR : CONSULT Function (BCM - AIR PRES-SURE MONITOR)"

>> Inspection End

Trang 20

< BASIC INSPECTION >

TRANSMITTER WAKE UP OPERATION

TRANSMITTER WAKE UP OPERATION

This procedure must be performed after replacement of a transmitter or the BCM, or rotation of the wheels

NOTE:

This procedure must be done after replacement of a TPMS transmitter or BCM New replacement transmittersare provided "asleep" and must first be "woken up" using Transmitter Activation Tool J-45295 or Signal Tech IITool J-50190 before ID registration can be performed Use the following procedure when using the TransmitterActivation Tool J-45295

NOTE:

The Signal Tech II Tool (J-50190) can be used to perform the following functions Refer to the Signal Tech IIUser Guide for additional information

• Activate and display TPMS transmitter IDs

• Display tire pressure reported by the TPMS transmitter

• Read TPMS DTCs

• Register TPMS transmitter IDs

1 Turn the ignition switch ON

NOTE:

The position of an inactive transmitter can be identified by checking the blinking timing of the low tire sure warning lamp

pres-2 Place transmitter activation tool (J-45295) (1) against side of tire

at location closest to transmitter

3 Press and hold transmitter activation tool button until indicator

lamp turns OFF (approximately 5 seconds)

NOTE:

Perform wake-up procedure starting from front left wheel, then

repeat procedure for front right wheel, rear right wheel, and rear

left wheel

4 Check that turn signal lamps blink twice when transmitter

wake-up procedure for all wheels is completed

5 Check that low tire pressure warning lamp turns OFF after

trans-mitter wake-up procedure is completed for all wheels

6 Perform the transmitter ID registration procedure Refer to WT-21, "Work Procedure"

JPEIC0089GB

NNEIC0020ZZ

Trang 21

This procedure must be performed after replacing wheels, transmitters or the BCM, or rotating wheels.

NOTE:

The Signal Tech II Tool (J-50190) can be used to perform the following functions Refer to the Signal Tech IIUser Guide for additional information

• Activate and display TPMS transmitter IDs

• Display tire pressure reported by the TPMS transmitter

• Read TPMS DTCs

• Register TPMS transmitter IDs

WITH TRANSMITTER ACTIVATION TOOL

NOTE:

This procedure must be done after replacement of a TPMS transmitter or BCM New replacement transmittersare provided "asleep" and must first be "woken up" using Transmitter Activation Tool J-45295 or Signal Tech IITool J-50190 before ID registration can be performed Use the following procedure when using the TransmitterActivation Tool J-45295

With CONSULT

1 Turn the ignition switch ON

2 On “WORK SUPPORT” select “ID REGIST.”

3 Select Start on “ID REGIST” screen

4 Place transmitter activation tool (J-45295) (1) against side of tire

at location closest to transmitter

5 Press and hold transmitter activation tool button until indicator

lamp turns OFF (approximately 5 seconds)

NOTE:

Perform ID registration procedure starting from front left wheel,

then repeat procedure for front right wheel, rear right wheel, and

rear left wheel

6 When ID registration is complete, check the following pattern at each wheel

7 After the ID registration procedure for all wheels is complete, press “End” to finish ID registration, thencheck that ID registration for all wheels is complete

WITHOUT TRANSMITTER ACTIVATION TOOL

NOTE:

This procedure must be done after replacement of a TPMS transmitter or BCM New replacement transmittersare provided "asleep" and must first be "woken up" using Transmitter Activation Tool J-45295 or Signal Tech IITool J-50190 before ID registration can be performed

With CONSULT

1 Turn the ignition switch ON

2 On “WORK SUPPORT” select “ID REGIST.”

3 Select Start on “ID REGIST” screen

Trang 22

< BASIC INSPECTION >

ID REGISTRATION PROCEDURE

5 Drive the vehicle at a speed greater than 40 km/h (25 MPH) for 3 minutes or more

6 After ID registration for all wheels is complete, press “End” to finish ID registration

7 Adjust the tire pressures for all wheels to the specified value Refer to WT-45, "Tire Air Pressure"

Tire position Tire pressure kPa (kg/cm 2 , psi)

Ngày đăng: 12/04/2014, 16:44

TỪ KHÓA LIÊN QUAN

w