HỆ THỐNG CHIẾU SÁNG BÊN NGOÀI TRÊN NISSAN VERSA SEDAN ĐỜI 2012
EXL-1 DRIVER CONTROLS C D E F G H I J K M SECTION EXL A B EXL N O P CONTENTS EXTERIOR LIGHTING SYSTEM PRECAUTION 4 PRECAUTIONS 4 Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TEN- SIONER" 4 Precaution for Work 4 PREPARATION 5 PREPARATION 5 Special Service Tool 5 SYSTEM DESCRIPTION 6 COMPONENT PARTS 6 Component Parts Location 6 Component Description 7 SYSTEM 8 HEADLAMP SYSTEM 8 HEADLAMP SYSTEM : System Diagram 8 HEADLAMP SYSTEM : System Description 8 WITH DAYTIME LIGHT SYSTEM 8 WITH DAYTIME LIGHT SYSTEM : System Dia- gram 9 WITH DAYTIME LIGHT SYSTEM : System De- scription 9 FRONT FOG LAMP SYSTEM 9 FRONT FOG LAMP SYSTEM : System Diagram 9 FRONT FOG LAMP SYSTEM : System Descrip- tion 9 TURN SIGNAL AND HAZARD WARNING LAMP SYSTEM 10 TURN SIGNAL AND HAZARD WARNING LAMP SYSTEM : System Diagram 10 TURN SIGNAL AND HAZARD WARNING LAMP SYSTEM : System Description 10 PARKING, LICENSE PLATE AND TAIL LAMP SYSTEM 10 PARKING, LICENSE PLATE AND TAIL LAMP SYSTEM : System Diagram 10 PARKING, LICENSE PLATE AND TAIL LAMP SYSTEM : System Description 11 DIAGNOSIS SYSTEM (BCM) 12 COMMON ITEM 12 COMMON ITEM : CONSULT Function (BCM - COMMON ITEM) 12 BUZZER 13 BUZZER : CONSULT Function (BCM - BUZZER) 13 HEADLAMP 13 HEADLAMP : CONSULT Function (BCM - HEAD LAMP) 13 FLASHER 14 FLASHER : CONSULT Function (BCM - FLASH- ER) 14 COMB SW 14 COMB SW : CONSULT Function (BCM - COMB SW) 14 BCM 15 BCM : CONSULT Function (BCM - BCM) 15 BATTERY SAVER 15 BATTERY SAVER : CONSULT Function (BCM - BATTERY SAVER) 15 DIAGNOSIS SYSTEM (IPDM E/R) 17 Diagnosis Description 17 CONSULT Function (IPDM E/R) 18 ECU DIAGNOSIS INFORMATION 20 BCM, IPDM E/R 20 List of ECU Reference 20 Revision: July 2011 2012 Versa Sedan EXL-2 WIRING DIAGRAM 21 HEADLAMP 21 Wiring Diagram 21 DAYTIME LIGHT SYSTEM 26 Wiring Diagram 26 FRONT FOG LAMP 31 Wiring Diagram 31 TURN SIGNAL AND HAZARD WARNING LAMP SYSTEM 35 Wiring Diagram 35 PARKING, LICENSE PLATE AND TAIL LAMPS SYSTEM 40 Wiring Diagram 40 STOP LAMP 47 Wiring Diagram 47 BACK-UP LAMP 50 Wiring Diagram 50 BASIC INSPECTION 53 DIAGNOSIS AND REPAIR WORKFLOW 53 Work Flow 53 DTC/CIRCUIT DIAGNOSIS 56 POWER SUPPLY AND GROUND CIRCUIT 56 BCM (BODY CONTROL MODULE) 56 BCM (BODY CONTROL MODULE) : Diagnosis Procedure 56 IPDM E/R (INTELLIGENT POWER DISTRIBU- TION MODULE ENGINE ROOM) 56 IPDM E/R (INTELLIGENT POWER DISTRIBU- TION MODULE ENGINE ROOM) : Diagnosis Pro- cedure 56 HEADLAMP (HI) CIRCUIT 58 Description 58 Component Function Check 58 Diagnosis Procedure 58 HEADLAMP (LO) CIRCUIT 60 Description 60 Component Function Check 60 Diagnosis Procedure 60 PARKING LAMP CIRCUIT 63 Description 63 Component Function Check 63 Diagnosis Procedure 63 TURN SIGNAL LAMP CIRCUIT 66 Description 66 Component Function Check 66 Diagnosis Procedure 66 FRONT FOG LAMP CIRCUIT 69 Component Function Check 69 Diagnosis Procedure 69 SYMPTOM DIAGNOSIS 72 EXTERIOR LIGHTING SYSTEM SYMPTOMS 72 Symptom Table 72 BOTH SIDE HEADLAMPS DO NOT SWITCH TO HIGH BEAM 74 Description 74 Diagnosis Procedure 74 BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON 75 Description 75 Diagnosis Procedure 75 PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED ON 76 Description 76 Diagnosis Procedure 76 BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON 77 Description 77 Diagnosis Procedure 77 PERIODIC MAINTENANCE 78 HEADLAMP AIMING ADJUSTMENT 78 Description 78 Aiming Adjustment 78 FRONT FOG LAMP AIMING ADJUSTMENT 80 Description 80 Aiming Adjustment Procedure 80 REMOVAL AND INSTALLATION 81 FRONT COMBINATION LAMP 81 Exploded View 81 Removal and Installation 81 Replacement 81 Disassembly and Assembly 82 FRONT FOG LAMP 83 Exploded View 83 Removal and Installation 83 Replacement 83 COMBINATION SWITCH 85 Exploded View 85 Removal and Installation 85 HAZARD SWITCH 86 Exploded View 86 Removal and Installation 86 REAR COMBINATION LAMP 87 Exploded View 87 Revision: July 2011 2012 Versa Sedan EXL-3 C D E F G H I J K M A B EXL N O P Removal and Installation 87 Disassembly 87 Replacement 88 HIGH-MOUNTED STOP LAMP 90 Exploded View 90 Removal and Installation 90 Replacement 90 LICENSE PLATE LAMP 91 Exploded View 91 Removal and Installation 91 Replacement 91 SERVICE DATA AND SPECIFICATIONS (SDS) 92 SERVICE DATA AND SPECIFICATIONS (SDS) 92 Bulb Specifications 92 Revision: July 2011 2012 Versa Sedan EXL-4 < PRECAUTION > PRECAUTIONS PRECAUTION PRECAUTIONS Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" INFOID:0000000007732311 The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted. Information necessary to service the system safely is included in the SR and SB section of this Service Man- ual. WARNING: • To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in the event of a collision which would result in air bag inflation, all maintenance must be performed by an authorized NISSAN/INFINITI dealer. • Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag Module, see the SR section. • Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har- ness connectors. PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS WARNING: • When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni- tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing serious injury. • When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the battery, and wait at least 3 minutes before performing any service. Precaution for Work INFOID:0000000007732312 • When removing or disassembling each component, be careful not to damage or deform it. If a component may be subject to interference, be sure to protect it with a shop cloth. • When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component with a shop cloth or vinyl tape to protect it. • Protect the removed parts with a shop cloth and prevent them from being dropped. • Replace a deformed or damaged clip. • If a part is specified as a non-reusable part, always replace it with new one. • Be sure to tighten bolts and nuts securely to the specified torque. • After installation is complete, be sure to check that each part works properly. • Follow the steps below to clean components. - Water soluble dirt: Dip a soft cloth into lukewarm water, and wring the water out of the cloth to wipe the dirty area. Then rub with a soft and dry cloth. - Oily dirt: Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%), and wipe the dirty area. Then dip a cloth into fresh water, and wring the water out of the cloth to wipe the detergent off. Then rub with a soft and dry cloth. • Do not use organic solvent such as thinner, benzene, alcohol, or gasoline. • For genuine leather seats, use a genuine leather seat cleaner. Revision: July 2011 2012 Versa Sedan PREPARATION EXL-5 < PREPARATION > C D E F G H I J K M A B EXL N O P PREPARATION PREPARATION Special Service Tool INFOID:0000000007732964 The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here. Tool number (Kent-Moore No.) Tool name Description — ( J-46534 ) Trim tool set For removing trim AWJIA0483ZZ Revision: July 2011 2012 Versa Sedan EXL-6 < SYSTEM DESCRIPTION > COMPONENT PARTS SYSTEM DESCRIPTION COMPONENT PARTS Component Parts Location INFOID:0000000007688758 AWLIA1889ZZ Revision: July 2011 2012 Versa Sedan COMPONENT PARTS EXL-7 < SYSTEM DESCRIPTION > C D E F G H I J K M A B EXL N O P Component Description INFOID:0000000007697741 1. BCM 2. Combination switch (lighting and turn signal switch) 3. Combination meter 4. Hazard switch 5. IPDM E/R, Daytime light relays 1 and 2 (if equipped), Front fog lamp relay (if equipped) 6. Stop lamp switch 7. Front combination lamp LH, RH 8. Front fog lamp LH, RH (if equipped) 9. Rear combination lamp LH, RH 10. License plate lamp LH, RH 11. High mounted stop lamp Part name Description BCM Controls the exterior lighting system. Combination meter • Blinks the turn signal indicator lamp and outputs the turn signal operating sound with integrated buzzer according to the re- quest from BCM (via CAN communication). • Turns the tail lamp indicator lamp and high beam indicator lamp ON according to the request from BCM (via CAN communica- tion). Combination switch (lighting and turn signal switch) Refer to BCS-7, " COMBINATION SWITCH READING SYSTEM : System Description". Hazard switch Hazard flasher request signal is output to the BCM. IPDM E/R Controls the integrated relay, and supplies voltage to the load ac- cording to the request from BCM (via CAN communication). Stop lamp switch Stop lamp signal is output to the rear combination lamps and high- mounted stop lamp. Revision: July 2011 2012 Versa Sedan EXL-8 < SYSTEM DESCRIPTION > SYSTEM SYSTEM HEADLAMP SYSTEM HEADLAMP SYSTEM : System Diagram INFOID:0000000007689720 HEADLAMP SYSTEM : System Description INFOID:0000000007689721 LOW BEAM OPERATION When the lighting switch is in 2ND position, the BCM receives input requesting the headlamps to illuminate. This input is communicated to the IPDM E/R across the CAN communication lines. The CPU of the IPDM E/R controls the headlamp low relay coil which supplies power to the low beam headlamps. HIGH BEAM OPERATION/FLASH-TO-PASS OPERATION With the lighting switch in the 2ND position and placed in HIGH position, the BCM receives input requesting the headlamp high beams to illuminate. The flash to pass feature can be used any time and also sends a sig- nal to the BCM. This input is communicated to the IPDM E/R across the CAN communication lines. The CPU of the combination meter controls the ON/OFF status off the HIGH BEAM indicator. The CPU of the IPDM E/R controls the headlamp high relay coil which supplies power to the high beam headlamps. The combination meter receives a high beam request signal (ON) through the CAN communication lines and turns the high beam indicator lamp ON. EXTERIOR LAMP BATTERY SAVER CONTROL With the combination switch (lighting and turn signal switch) in the 2ND position and the ignition switch is turned from ON or ACC to OFF, the battery saver feature is activated. Under this condition, the headlamps remain illuminated for 5 minutes unless the lighting switch position is changed. If the lighting switch position is changed, then the headlamps are turned off. This setting can be changed by CONSULT. Refer to BCS-17, " HEADLAMP : CONSULT Function (BCM - HEAD LAMP)". WITH DAYTIME LIGHT SYSTEM ABLIA2706GB Revision: July 2011 2012 Versa Sedan SYSTEM EXL-9 < SYSTEM DESCRIPTION > C D E F G H I J K M A B EXL N O P WITH DAYTIME LIGHT SYSTEM : System Diagram INFOID:0000000007689724 WITH DAYTIME LIGHT SYSTEM : System Description INFOID:0000000007689725 The headlamp system is equipped with a daytime light relay 1 that activates the high beam headlamps at approximately half illumination whenever the engine is operating and the lighting switch is in the OFF position. If the parking brake is applied before the engine is started the daytime lights will not be illuminated. The day- time lights will illuminate once the parking brake is released. With the lighting switch in the 2nd position the headlamps function the same as conventional light systems. The BCM monitors inputs from the parking brake switch and the lighting switch to determine when to activate the daytime light system. The BCM sends a daytime light request to the IPDM E/R via the CAN communica- tion lines. The IPDM E/R grounds the daytime light relay 1 which in turn, provides power to the ground side of the LH high beam lamp. Power flows backward through the LH high beam lamp to the IPDM E/R, through fuse 35, fuse 34 and to the RH high beam lamp and on to ground. The high beam lamps are wired in series which causes them to illuminate at a reduced intensity. FRONT FOG LAMP SYSTEM FRONT FOG LAMP SYSTEM : System Diagram INFOID:0000000007689728 FRONT FOG LAMP SYSTEM : System Description INFOID:0000000007689729 FRONT FOG LAMP OPERATION When the combination switch (lighting and turn signal switch) is in front fog lamp ON position and also in 1ST or 2ND position (headlamp is ON), the BCM detects FR FOG ON and the HEAD LAMP 1 or 2 ON. The BCM sends a front fog lamp request ON signal through the CAN communication lines to the IPDM E/R. The IPDM E/R then turns ON the front fog lamp relay sending power to the front fog lamps. AWLIA1885GB AWLIA1886GB Revision: July 2011 2012 Versa Sedan EXL-10 < SYSTEM DESCRIPTION > SYSTEM TURN SIGNAL AND HAZARD WARNING LAMP SYSTEM TURN SIGNAL AND HAZARD WARNING LAMP SYSTEM : System Diagram INFOID:0000000007689732 TURN SIGNAL AND HAZARD WARNING LAMP SYSTEM : System Description INFOID:0000000007689733 TURN SIGNAL OPERATION When the turn signal switch is in LH or RH position with the ignition switch in ON position, the BCM detects the TURN RH or TURN LH ON request. The BCM outputs the flasher output signal to the respective turn signal lamp. The BCM sends a turn indicator signal ON request through the CAN communication lines to the combi- nation meter. The combination meter then activates the appropriate turn signal indicator and audible buzzer. HAZARD LAMP OPERATION When the hazard switch is in ON position, the BCM detects the hazard switch signal ON. The BCM outputs the flasher output signal (right and left). The BCM sends a hazard indicator signal ON request through the CAN communication lines to the combination meter. The combination meter then activates the hazard indicator and audible buzzer. REMOTE KEYLESS ENTRY OPERATION The remote keyless entry receiver transmits hazard lamp signal to BCM, then BCM controls hazard lamps. Refer to DLK-15, " REMOTE KEYLESS ENTRY SYSTEM : System Description". PARKING, LICENSE PLATE AND TAIL LAMP SYSTEM PARKING, LICENSE PLATE AND TAIL LAMP SYSTEM : System Diagram INFOID:0000000007689736 ABLIA2705GB AWLIA1753GB Revision: July 2011 2012 Versa Sedan [...]... INFOID:0000000007688777 B C D E F G H I J K EXL M N O P ABLWA1480GB Revision: July 2011 EXL- 21 2012 Versa Sedan HEADLAMP < WIRING DIAGRAM > ABLIA3120GB Revision: July 2011 EXL- 22 2012 Versa Sedan HEADLAMP < WIRING DIAGRAM > A B C D E F G H I J K EXL M N O ABLIA3121GB P Revision: July 2011 EXL- 23 2012 Versa Sedan HEADLAMP < WIRING DIAGRAM > ABLIA3122GB Revision: July 2011 EXL- 24 2012 Versa Sedan HEADLAMP < WIRING DIAGRAM... M N O P ABLWA1482GB Revision: July 2011 EXL- 31 2012 Versa Sedan FRONT FOG LAMP < WIRING DIAGRAM > ABLIA3128GB Revision: July 2011 EXL- 32 2012 Versa Sedan FRONT FOG LAMP < WIRING DIAGRAM > A B C D E F G H I J K EXL M N O ABLIA3129GB P Revision: July 2011 EXL- 33 2012 Versa Sedan FRONT FOG LAMP < WIRING DIAGRAM > ABLIA3130GB Revision: July 2011 EXL- 34 2012 Versa Sedan TURN SIGNAL AND HAZARD WARNING LAMP... Revision: July 2011 EXL- 28 2012 Versa Sedan DAYTIME LIGHT SYSTEM < WIRING DIAGRAM > A B C D E F G H I J K EXL M N O ABLIA3126GB P Revision: July 2011 EXL- 29 2012 Versa Sedan DAYTIME LIGHT SYSTEM < WIRING DIAGRAM > ABLIA3127GB Revision: July 2011 EXL- 30 2012 Versa Sedan FRONT FOG LAMP < WIRING DIAGRAM > FRONT FOG LAMP A Wiring Diagram INFOID:0000000007688779 B C D E F G H I J K EXL M N O P ABLWA1482GB... DIAGRAM > A B C D E F G H I J K EXL M N O ABLIA3123GB P Revision: July 2011 EXL- 25 2012 Versa Sedan DAYTIME LIGHT SYSTEM < WIRING DIAGRAM > DAYTIME LIGHT SYSTEM Wiring Diagram INFOID:0000000007688778 ABLWA1481GB Revision: July 2011 EXL- 26 2012 Versa Sedan DAYTIME LIGHT SYSTEM < WIRING DIAGRAM > A B C D E F G H I J K EXL M N O ABLIA3124GB P Revision: July 2011 EXL- 27 2012 Versa Sedan DAYTIME LIGHT SYSTEM... DIAGRAM > TURN SIGNAL AND HAZARD WARNING LAMP SYSTEM Wiring Diagram A INFOID:0000000007688780 B C D E F G H I J K EXL M N O P ABLWA1483GB Revision: July 2011 EXL- 35 2012 Versa Sedan TURN SIGNAL AND HAZARD WARNING LAMP SYSTEM < WIRING DIAGRAM > ABLIA3131GB Revision: July 2011 EXL- 36 2012 Versa Sedan ... 2011 EXL- 19 2012 Versa Sedan BCM, IPDM E/R < ECU DIAGNOSIS INFORMATION > ECU DIAGNOSIS INFORMATION BCM, IPDM E/R List of ECU Reference INFOID:0000000007688776 ECU Reference BCS-24, "Reference Value" BCM BCS-35, "Fail-safe" BCS-35, "DTC Inspection Priority Chart" BCS-36, "DTC Index" PCS-10, "Reference Value" IPDM E/R PCS-14, "Fail-Safe" PCS-15, "DTC Index" Revision: July 2011 EXL- 20 2012 Versa Sedan. .. is changed, then the headlamps are turned off This setting can be changed by CONSULT Refer to BCS-21, "BATTERY SAVER : CONSULT Function (BCM - BATTERY SAVER)" D E F G H I J K EXL M N O P Revision: July 2011 EXL- 11 2012 Versa Sedan DIAGNOSIS SYSTEM (BCM) < SYSTEM DESCRIPTION > DIAGNOSIS SYSTEM (BCM) COMMON ITEM COMMON ITEM : CONSULT Function (BCM - COMMON ITEM) INFOID:0000000007688767 APPLICATION ITEM... location C D E F G H I J K EXL Operation M 1 Front wiper LO for 5 seconds → HI for 5 seconds 2 • • • • 10 seconds 3 Headlamp LO for 10 seconds →HI ON ⇔ OFF 5 times 4 A/C compressor (magnet clutch) ON ⇔ OFF 5 times 5 Cooling fan LO for 5 seconds → MID for 3 seconds → HI for 2 seconds Parking lamp License plate lamp Tail lamp Front fog lamp N O P Revision: July 2011 EXL- 17 2012 Versa Sedan DIAGNOSIS SYSTEM... KEYLESS LOCK [On/Off] Indicates condition of lock signal from keyfob PKB SW [On/Off] Indicates park brake switch signal received from combination meter on CAN communication line Revision: July 2011 EXL- 13 2012 Versa Sedan DIAGNOSIS SYSTEM (BCM) < SYSTEM DESCRIPTION > Monitor Item [Unit] Description ENGINE RUN [On/Off] Indicates engine run signal received from ECM on CAN communication line VEHICLE SPEED [km/h/mph]... FLASHER Description This test is able to check turn signal lamp operation [Off/LH/RH] COMB SW COMB SW : CONSULT Function (BCM - COMB SW) INFOID:0000000007688771 DATA MONITOR Revision: July 2011 EXL- 14 2012 Versa Sedan DIAGNOSIS SYSTEM (BCM) < SYSTEM DESCRIPTION > Monitor Item [Unit] Description A TURN SIGNAL R [On/Off] Indicates condition of right turn signal operation of combination switch TURN SIGNAL . 2011 2012 Versa Sedan EXL-6 < SYSTEM DESCRIPTION > COMPONENT PARTS SYSTEM DESCRIPTION COMPONENT PARTS Component Parts Location INFOID:0000000007688758 AWLIA1889ZZ Revision: July 2011 2012 Versa. 86 Removal and Installation 86 REAR COMBINATION LAMP 87 Exploded View 87 Revision: July 2011 2012 Versa Sedan EXL-3 C D E F G H I J K M A B EXL N O P Removal and Installation 87 Disassembly 87 Replacement. (SDS) 92 SERVICE DATA AND SPECIFICATIONS (SDS) 92 Bulb Specifications 92 Revision: July 2011 2012 Versa Sedan EXL-4 < PRECAUTION > PRECAUTIONS PRECAUTION PRECAUTIONS Precaution for Supplemental