Available online at www.sciencedirect.com ScienceDirect Energy Procedia 96 (2016) 592 – 600 SBE16 Tallinn and Helsinki Conference; Build Green and Renovate Deep, 5–7 October 2016, Tallinn and Helsinki Integrated design of museum’s indoor climate in medieval Episcopal Castle of Haapsalu Margus Nappa, Targo Kalameesa,*, Teet Tarkb, Endrik Arumägia a Tallinn University of Technology, Ehitajate tee 5, Tallinn 12616, Estonia Hevac OÜ, Laki 16, Tallinn 10621, Estonia Abstract The ruins of medieval Episcopal Castle of Haapsalu in Estonia are planned to be taken into use as a museum Due to conservational, architectural or economic reasons, it is difficult or sometimes also impossible to install climate systems into historic buildings Before the design process, indoor climate measurements have been carried out to get an overview of the current situation, the needs for changes, to get data for model calibration and to work out the design strategy Combined heat, air, and moisture simulations were performed with IDA-ICE software together with different indoor climate control strategies and different outdoor climatic conditions (typical year, warm summer, cold winter, humid autumn) The interaction of indoor air and moisture performance of building envelope was taken into account Simulation model was calibrated based on field measurements and the results of simulations showed reasonable agreement with field measurements By simulations, different climate control systems were analyzed and their necessity and the extent of performance were determined The main target is to find out capability of passive measures for climate conditions to avoid active drying and humidifying Results showed that: with only passive indoor climate measured the indoor climate is strongly dependent of the outdoor climate as well as the massive limestone walls with large thermal and moisture capacity Without indoor climate systems there is extensive indoor temperature and relative humidity fluctuation throughout the year To ensure suitable indoor climate, room heating, humidification during winter period, and dehumidification during summer and autumn periods is needed It was difficult to provide strict required indoor climate conditions for museums through the year only with passive measures © 2016 The Authors Published by Elsevier Ltd ThisLtd is an open access article under the CC BY-NC-ND license © 2016 The Authors Published by Elsevier (http://creativecommons.org/licenses/by-nc-nd/4.0/) Peer-review under the responsibility of the organizing committee of the SBE16 Tallinn and Helsinki Conference Peer-review under responsibility of the organizing committee of the SBE16 Tallinn and Helsinki Conference Keywords: indoor climate; energy simulations; museums; monumental buildings; * Corresponding author Tel.: +372 620 2403 E-mail address: targo.kalamees@ttu.ee 1876-6102 © 2016 The Authors Published by Elsevier Ltd This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/licenses/by-nc-nd/4.0/) Peer-review under responsibility of the organizing committee of the SBE16 Tallinn and Helsinki Conference doi:10.1016/j.egypro.2016.09.105 Margus Napp et al / Energy Procedia 96 (2016) 592 – 600 593 Introduction The design of indoor climate in museums is a complex, multidisciplinary problem Integrated design is needed to guarantee the conservation of objects and architecture as well as to reach high performance in energy efficiency, indoor climate and moisture safety in building physics The solution should fulfil the need for preservation of interior objects and the building itself as well provide appropriate climate conditions for human comfort Indoor climate is strictly conditioned in modern museums [1,2] It is attractive to house museums in monumental buildings that also have heritage value Usually these heritage buildings were not originally built for the purpose of being a museum While designing suitable indoor climate in monumental buildings, it is necessary to pay extra attention to using the space for building service systems Building’s massive walls with large thermal transmittance and large heat and moisture capacity are essential to take into account Poor indoor climate design can cause damage to the artefacts in a museum The deterioration of wooden objects [3–5], mould growth [6,5], and indoor air pollution [7] can occur There have been many case studies on museums in monumental buildings Schellen and Martens [8] conducted a case study in the Netherlands and investigated the indoor climate and HVAC systems in local monumental museums In their study, Kramer et al [9] showed how different ASHRAE’s museum climate classes influence energy use and protect artefacts Arumägi et al analysed the renovation possibilities of indoor climate in the Old Observatory in Tartu [10] A RH-sensitive heating and ventilation system was developed to keep the RH and temperature at target level For the preservation of the artefacts in a museum, complex and large climate systems are needed There are many possibilities to provide indoor climate in medieval buildings with valuable interior [11, 12] Due to conservational, architectural or economic reasons, it is difficult or sometimes also impossible to install these systems into historic buildings In this study, indoor climate simulations for the museum in Episcopal Castle of Haapsalu are conducted to investigate the indoor climate and the necessity of different climate systems in monumental museum The main target is to find out capability of passive measures for climate conditions to avoid active drying and humidifying Methods 2.1 Building and measurements Episcopal Castle of Haapsalu was established in the 13th century and it is one of the oldest castles in Estonia (Fig 1) It has massive walls typical of a medieval stronghold castle The castle is located in the city centre of Haapsalu and today, it accommodates a museum and the dome church a b Fig (a) Episcopal Castle of Haapsalu; (b) first floor plan view of the castle 594 Margus Napp et al / Energy Procedia 96 (2016) 592 – 600 Indoor climate measurements in the Castle of Haapsalu were carried out in autumn 2015 to obtain data for the calibration of indoor climate simulation model Temperature and relative humidity were measured with HOBO U12 001 data loggers with the interval of 15 minutes In total, loggers were used: located in the dome church, in the castle cellar, on the first floor of the castle (Fig 1, b), and one on the third floor of the castle 2.2 Simulation Since the envelope of the church has a massive heat and moisture capacity, it is essential to use dynamic computer simulation to calculate the church’s indoor climate and energy usage IDA Indoor Climate and Energy software [13, 14] was used for indoor climate and energy simulations This software is meticulously validated [15– 20] allowing the modelling of a multi-zone building, internal and solar loads, outdoor climate, HVAC systems, dynamic simulation of heat transfer and air flows It has also been used in many energy performance and indoor climate applications [21–25] In the programme, a mathematical model was created of the building where the movement of air, heat, and moisture through the structures and rooms and energy for heating, ventilation, and humidification-dehumidification were taken into account In the mathematical model, three different wall types were used The walls have been divided into 17…19 layers and to calculate moisture transfer, the common wall model RCWall should be replaced with the HAMWall model [26] There were two external simulation walls and two internal walls Because HAMWall can only be used as an external wall, one meter insulation layer was used as an outer layer of internal walls to cut the heat transfer with external environment Structure material properties and hygric properties are presented in Table and Table Table Structures, materials, and their thermal properties Structure Exterior wall Attic floor Floor Door Materials (from indoor to outdoor) Thickness d, m Thermal conductivity O, W / (m·K) Specific heat c, J / (kg·K) Density U, kg / m3 Render 0.025 0.8 790 1800 Lime stone masonry 1.45 1.5 880 2300 Render 0.025 0.8 790 1800 Render 0.025 0.8 790 1800 Limestone arch 0.4 1.5 880 2300 Render 0.025 0.8 790 1800 Lime stone slab 0.25 1.5 880 2300 Soil 1.0 2.0 1000 2000 Wood 0.05 0.13 1.0 510 Table Material’s hygric properties Water vapour transmission1 Material G0, m /s B -7 Limestone 1.89x10 Render 2.929x10-6 Wood 7.3x10 -7 6.4x10 -7 3.8x10-6 2.9x10 -6 Sorption isotherm2 C RH1, % w1, kg/m3 RH2, % w2, kg/m3 4.7 82 80 100 100 10 20 57 100 82 4.75 84 72 100 100 Water vapour Gv = G0 + B(RH/100)c, m2/s, where G0, m2/s is if RH=0%, B and C are constants and RH, % Water vapour capacity relation to relative humidity is given with three lines: start: w=0kg/m 3, RH=0%, first breakpoint: w1; RH1, second breakpoint: w2; RH2=100% 595 Margus Napp et al / Energy Procedia 96 (2016) 592 – 600 Table Simulation cases + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + for h + People: 2x per day + + m2 + + + Water surface + + 25 m2 + Water surface + min: 40% + + Humidification + + Night: 0.3 /(s·m2) Ventilation supply + + Day; 2.5 l/(s·m2) Winter +10 °C + + l/(s·m2) Cold winter + + 70 % RH Humid autumn + Conservation heating Warm summer Ventilation 10 °C EstonianTRY Heating Simulation case Outdoor climate + + 2.3 Climate and simulation models Because of the massive and complex construction of the building, only one typical room was investigated in the simulation The validation of the simulation model was done with outdoor measurements from October to November 2015 Four different climate conditions were used to test how different climate conditions affect the indoor climate: EstonianTRY (Estonian test reference year for energy simulations [27]), warm summer, humid autumn, and cold winter All simulation cases are presented in Table Targets for indoor climate were: ti>10 °C and RH 40-70 % Winter period heating of +10 °C was taken as a base line Local room unit was added to the simulation with the set point of +10 ºC Supply air temperature was also limited to +10 ºC To this end, a heater was added to air handling unit to heat up the inlet air to +10 ºC Conservation heating was added to prevent the relative humidity to rise above the desired set point Local room heating unit was added to the simulation The heater was controlled with relative humidity When room relative humidity exceeded the given set point of 70% RH, the heater would start to work to decrease the RH level in the room Two different ventilation airflow rates were used in the different cases of simulations: constant airflow rate of l/(s·m2) and variable airflow rates for day and night were used when 2.5 l/(s·m2) was used from 10:00 to 18:00 and during night, airflow rate of 0.3 l/(s·m2) was used Different airflow rates were used to simulate more real conditions, where during day time, greater air change would be used during museum visiting hours Room humidification (not in air handling unit) was used for some cases to prevent the RH to below desired limit Humidifier was added to the air handling unit in the simulation Set point of 40% RH was used for humidification Water surface was used to simulate the massive heat and moisture capacity and moisture transfer between the room and the walls Water surface of 25 m2 was received with the model calibration Water surface of m2 was used in two simulations to see how indoor climate and the energy consumption of climate control systems would change after longer period of time when the massive walls have dried out and the moisture transfer from walls to the room reduced People were added to the simulation to see how their presence would change the indoor climate Two 20 people groups were added to the simulations for two hours, from 11:00 to 13:00 and 14:00 to 16:00 596 Margus Napp et al / Energy Procedia 96 (2016) 592 – 600 Results and Discussion 3.1 Calibration of the model The model was calibrated according to the field measurements that were carried out in the Castle of Haapsalu between the period from 24 October to 23 November 2015 The calibration showed that there are few differences between the simulated and measured indoor temperature Simulation temperature is slightly more affected by the change of outdoor temperature, but regardless of the fact that there is good agreement between the temperature of measured and calibrated model There was also satisfactory agreement between the measured and simulated moisture content [28] 3.2 Indoor climate simulations 3.2.1 Simulation case The purpose of this case was to determine the need of drying and humidifying systems With the first simulation room heating and minimum supply air temperature were applied The set point for both was +10 °C The simulation was done with all four outdoor climate conditions Highest room heating power was 60 W/m2 to maintain the indoor temperature of +10 °C The highest heating power applied to the supply air was also with the cold climate, 35 W/m Relative humidity (Fig 2, b), on the other hand, is very unstable and lies between 18…100% Throughout the year in 41% of the time the relative humidity is above 70% Lower RH in winter period is due to room heating Simulations show great moisture transfer fluctuation between the room and walls and mainly influenced by the outdoor climate Nevertheless, the average moisture transfer with different climate conditions is still 0.7…0.9 g/m3 from walls to room and it is derived from walls large water content With the supply air inlet air temperature being +10 °C and the airflow of l/(s·m2), the heating capacity with different climate conditions is between 24…36 W/m2 and the yearly energy consumption with cold climate 38 kWh/(m2·a) Because of large heat losses local heating unit is still needed to hold the minimum of +10 °C in the room The heating capacity for local unit with different climate conditions is between 46…61 W/m2 and the highest energy consumption is with cold winter, 151 kWh/(m2·a) a b Fig Simulation nr.1: a) temperature, b) relative humidity Margus Napp et al / Energy Procedia 96 (2016) 592 – 600 597 3.2.2 Simulation case With simulation case 2, conservation heating (CH) was added to the first simulation With CH, the indoor RH was controlled throughout the year to keep it RHd70% by heating the room to the point where relative humidity is reduced to an acceptable value Because the RH is the highest in summer and autumn with the period average of 75% then the heating capacity is the highest in this period, between 40…52 W/m2 in different climate conditions The energy consumption is the highest in cold climate, 53 kWh/(m2·a) CH also increases indoor temperature to reduce RH Annual average temperature increase is 1.3 °C and during the summer-autumn period when the RH is the highest, the average temperature increase is 2.2 °C Short term maximum temperature increase is 8.1 °C CH is capable to reduce the RH to the desired level Nevertheless, it is more efficient to use it in colder climate while there is desire to heat the room as well In the summer period, the usage of CH is not suitable as it will increase already high indoor temperature 3.2.3 Simulation cases 3–4 In simulation and 4, the water surface area was reduced to simulate the situation where for longer period of time the climate control systems in the room would have dried out the massive limestone walls and the moisture movement from the walls to the room would have reduced Water surface area of m per room was used Annual average moisture transfer from walls to the room was reduced by 0.77 g/m3, from 0.83 g/m3 to 0.06 g/m3 and the annual RH was reduced by 7% Indoor temperature difference was virtually unnoticeable Total annual energy consumption with supply air heating, room heating, and CH was reduced from 186 to 172 kWh/(m2·a) (without drying or humidifying in air handling unit) 3.2.4 Simulation case The airflow was changed in the fifth simulation from constant airflow of l/(s·m2) to variable airflow: 2.5 l/(s·m2) at the day time from 10:00 to 18:00, and 0.3 l/(s·m2) at night In addition, humidification was added to the room to keep the minimum RH of 40% in the room For this simulation only extreme climate conditions were used: warm summer and humid autumn Room heating is necessary to prevent the temperature to drop below the desired limit Heating reduces the RH in the room increasing the air potential to hold water vapour Therefore, humidification is necessary in the colder period where the outdoor moisture content is lower In summer period, larger airflow rate during the day time increases the indoor temperature The maximum indoor temperature is 28 °C in warm summer and above 24 °C, i.e 25% of the time in July RH in the summer time is 37% of time above 70% and in the autumn 41% of the time above 70% Ventilation airflow changes have also increased the maximum heating capacity of the ventilation heating unit from 32 W/m2 to 68 W/m2 with the humid autumn climate The maximum room heating capacity is 154 W/m2 Annual energy consumption compared to simulation case has increased from 132 kWh/(m2·a) to 192 kWh/(m2·a) This was also caused partly due to the changes in ventilation airflow rates 3.2.5 Simulation cases 6–7 With the simulation case 6, visitors were divided into two groups for two hours per day to the simulation to see how the heat and moisture production of the people would affect the indoor climate The room temperature reaches the maximum of 29.0 °C and in July, the temperature is 43% of the time above 24°C This is 18% more than it was with a simulation without people When CH is added with simulation case 7, the highest temperature in July is 29.6 °C and it is 60% of the time above 24°C that is 16% higher that with simulation case Simulations show that in summer period, temperature and RH values are quite high (Fig 3) This high temperature and RH conditions are not suitable for museums because they cause discomfort for visitors and museum staff High relative humidity levels with high enough temperature and also thrive mould growth [4,6] Therefore, in summer, cooling and dehumidification are needed 598 Margus Napp et al / Energy Procedia 96 (2016) 592 – 600 a b Fig Simulation nr.6: a) temperature, b) relative humidity Table Conclusion of simulation results Sim case Average temperature, ti °C D, J, F M, A, M J, S, Mont h J, A O, 10 11 10 12 10 10 Average RH, Capacity, Time when RH > 70%, % RHi, % M, A, M J, S, J, A O, N D, J, F 17 11 42 56 20 13 41 55 11 17 11 35 11 19 12 35 10 11 18 11 10 12 19 10 12 21 Energy use, kWh/(m2∙a) W/m2 M, A, M J, S, J, A O, N D, J, F 79 70 25 82 68 63 0 50 73 64 13 49 66 59 0 48 60 76 70 12 50 65 75 74 13 49 60 66 65 Heatin g Vent Heating Vent 54 61 36 155 38 61 36 190 38 63 61 36 156 38 0 61 36 176 38 28 73 52 154 69 195 19 40 69 63 149 69 158 19 0 0 149 67 191 19 N 3.2.6 The summary of simulation cases The summary of simulation results is presented in Table 4 Conclusion In this study research was carried out to analyse the indoor climate and the necessity of climate control systems in the museum of medieval Episcopal Castle of Haapsalu in Estonia The main target is to find out capability of passive measures for climate conditions to avoid active drying and humidifying Measurements and dynamic indoor climate and energy simulations showed following findings: x Short term field measurements and indoor climate simulations show that without the climate control systems in the Castle of Haapsalu the indoor temperature and relative humidity are unsuitable for museum exhibitions as well as for staff and visitors x Simulations show that the indoor climate is largely dependent of the outdoor climate as well as the massive limestone walls with large thermal and moisture capacity Margus Napp et al / Energy Procedia 96 (2016) 592 – 600 x Simulations indicate extensive indoor temperature fluctuation throughout the year without indoor climate systems Low room temperature was during the colder period In summer period, the indoor temperature of the room reaches quite high levels x Without indoor climate systems relative humidity annual fluctuation is between 18…100% Relative humidity is low in the colder periods due to the heating In summer and autumn periods, the indoor relative humidity is high and highly influenced by outdoor climate and ventilation x During extreme warm period, indoor temperature can increase above 27° C and can reach up to 1500 ºC·h x It was difficult to provide strict required indoor climate conditions for museums through the year only with passive measures Based on indoor climate and energy simulations we could make following recommendations for future design: x To ensure suitable indoor climate, room heating is needed Room units are needed to ensure the desired indoor temperature during the cold period that is suitable for the museum exhibitions as well for staff and visitors Supply air heating is required for air handling units to avoid cold air supply to the rooms x For suitable RH levels, winter period humidification is needed Due to the heating in winter period, RH can drop below the desired limit Low RH levels are unsuitable for museum exhibitions as it can cause cracking of moisture sensitive materials x Dehumidification in needed during summer and autumn periods Massive limestone walls as well as visitors increase the indoor relative humidity When cooling is added, the RH levels would rise even more and condensation on walls can occur Therefore, dehumidification is needed to keep the RH below the desired limit x Because in medieval castle it was difficult to provide strict required indoor climate conditions for museums through the year, very sensitive objects is needed keep in climatic chambers Acknowledgements This research was supported by the Estonian Centre of Excellence in Zero Energy and Resource Efficient Smart Buildings and Districts, ZEBE, grant TK146 funded by the European Regional Development Fund, and by the Estonian Research Council, with Institutional research funding grant IUT1−15 The research utilises the measured and simulated data from study financed by SA Läänemaa ja Haapsalu Muuseumid References [1] ASHRAE, ASHRAE Handbook - HVAC Applications (SI) - Chapter: Museums, Galleries, Archives, and Libraries, 2011 [2] EN 15757 Conservation of cultural property Specifications for temperature and relative humidity to limit climate-induced mechanical damage in organic hygroscopic materials, 2010 [3] Konsa K, Tirrul I, Hermann A Wooden objects in museums: Managing biodeterioration situation, International Biodeterioration & Biodegradation; 2014;86:165–170 doi:10.1016/j.ibiod.2013.06.023 [4] Mecklenburg M.F, Tumosa CS Structural response of painted wood surfaces to changes in ambient relative humidity, in: Painted Wood: History and Conservation; 1998: 464–483 [5] Kalamees T, Väli A, Kurik L, Napp M, Arumägi E, Kallavus U The influence of indoor climate control on risk for damages in naturally ventilated historic churches in cold climate International Journal of Architectural Heritage; 2015 doi:10.1080/15583058.2014.1003623 [6] Gaylarde CC, Morton LHG Deteriogenic biofilms on buildings and their control: A review Biofouling; 1999;44:59–74 doi:10.1080/08927019909378397 [7] Ryhl-Svendsen M Indoor air pollution in museums: a review of prediction models and control strategies Reviews in Conservation; 2006;7: 27–41 doi:10.1179/sic.2006.51.Supplement-1.27 [8] Martens M, Schellen H A sound indoor climate for a museum in a monumental building = Un sano clima interno per un museo in un edificio monumentale, in: Indoor Environment and Preservation: Climate Control in Museums and Historic Buildings = Ambiente Interno E Conservazione: Il Controllo Del Clima Nei Musei E Negli Edifici Storici; 2010: 183–189 599 600 Margus Napp et al / Energy Procedia 96 (2016) 592 – 600 [9] Kramer R, Schellen H, Schijndel J Energy Impact of ASHRAE’s Museum Climate Classes: A Simulation Study on Four Museums with Different Quality of Envelopes Energy Procedia; 2015;78:1317–1322 doi:10.1016/j.egypro.2015.11.147 [10] Arumägi, E., Kalamees, T., Õiger, K., Kallavus, U., Kurik, L Indoor climate analyzis of the Old Observatory in Tartu In: 9th International Conference and Exhibition - Healthy Buildings 2009; Syracuse, NY; United States, 13-17.09.2009 [11] Napp M, Kalamees T Energy use and indoor climate of conservation heating, dehumidification and adaptive ventilation for the climate control of a medieval church in a cold climate Energy and Buildings; 2015;108:61–71 doi:10.1016/j.enbuild.2015.08.013 [12] Napp M, Wessberg M, Kalamees T, Broström T Adaptive ventilation for climate control in a medieval church in cold climate International Journal of Ventilation; 2016;15:1-14, http://dx.doi.org/10.1080/14733315.2016.1173289 [13] Shalin P Modelling and simulation methods for modular continuous system in buildings, KTH, Stockholm, Sweden, 1996 [14] Björsell N, Bring A, Eriksson L, Grozman P, Lindgren M, Sahlin P, et al., IDA indoor climate and energy, in: Proceedings of the IBPSA Building Simulation ’99 Conference, Kyoto, Japan, 1999:1–8 [15] Moinard S, Guyon G Empirical Validation of EDF ETNA and GENEC Test-Cell Models Final Report IEA SHC Task 22 Building Energy Analysis Tools Project A.3., Moret sur Loing, France, 2000 [16] Travesi J, Maxwel G, Klaassen C, Holtz M Empirical validation of Iowa energy resource station building energy analysis simulation models, IEA Task 22, Subtask A, 2001 [17] Achermann M, Zweifel G RADTEST – Radiant heating and cooling test cases Subtask C A report of IEA Task 22 Building Energy Analysis Tools; 2003 [18] Kropf S, Zweifel G Validation of the Building Simulation Program IDA-ICE According to CEN 13791 „ Thermal Performance of Buildings - Calculation of Internal Temperatures of a Room in Summer Without Mechanical Cooling - General Criteria and Validation Procedures “, Hochschule Technik+Architektur Luzern HLK Engineering, 2001 [19] Mateo A, Aranaz T IDA simulation of indoor climate variations in a Church Validation of IDA model University of Gävle, 2011 [20] Woloszyn M, Kalamees T, Abadie MO, Steeman M, Sasic Kalagasidis A The effect of combining a relative-humidity-sensitive ventilation system with the moisture-buffering capacity of materials on indoor climate and energy efficiency of buildings, Building and Environment 2009;44:515–524 doi:10.1016/j.buildenv.2008.04.017 [21] Kuusk K, Kalamees T, Maivel M Cost effectiveness of energy performance improvements in Estonian brick apartment buildings Energy and Buildings; 2014;77: 313–322 doi:10.1016/j.enbuild.2014.03.026 [22] Alev Ü, Eskola L, Arumägi E, Jokisalo J, Donarelli A, Siren K, Broström T, Kalamees T Renovation alternatives to improve energy performance of historic rural houses in the Baltic Sea region, Energy and Buildings 2014;77:58–66 doi:10.1016/j.enbuild.2014.03.049 [23] Liu W, Huang C, Hu Y, Zou Z, Shen L, Sundell J Associations of building characteristics and lifestyle behaviors with home dampnessrelated exposures in Shanghai dwellings Building and Environment 2015;88:106-115 doi:10.1016/j.buildenv.2014.10.028 [24] Arumägi E, Kalamees T Analysis of energy economic renovation for historic wooden apartment buildings in cold climates Applied Energy 2014;11:540–548 doi:10.1016/j.apenergy.2013.10.041 [25] Kuusk K, Kalamees T Retrofit cost-effectiveness: Estonian apartment buildings Building Research & Information 2015:1–15 doi:10.1080/09613218.2016.1103117 [26] Kurnitski J, Vuolle M Simultaneous calculation of heat, moisture, and air transport in a modular simulation environment, Proceedings of the Estonian Academy of Sciences Engineering (2000) 25–47 [27] Kalamees T, Kurnitski J Estonian climate analysis for selecting the test reference year In Proceedings of HB 2006 - Healthy Buildings: Creating a Healthy Indoor Environment for People Lisboa; Portugal; 4-8.06 2006;5:207-212 [28] Kalamees T, Napp M, Arumägi E, Kallavus U, Kurik L Research of indoor climate in Medieval Episcopal Castle of Haapsalu (in Estonian) Tallinn University of Technology Tallinn, 2016 ... reasons, it is difficult or sometimes also impossible to install these systems into historic buildings In this study, indoor climate simulations for the museum in Episcopal Castle of Haapsalu. .. drying and humidifying Methods 2.1 Building and measurements Episcopal Castle of Haapsalu was established in the 13th century and it is one of the oldest castles in Estonia (Fig 1) It has massive... control systems in the museum of medieval Episcopal Castle of Haapsalu in Estonia The main target is to find out capability of passive measures for climate conditions to avoid active drying and