Fuel Charging and Controls — 2.5L Duratec-HE (122kW/165PS) 303-04A-1 - MI4 303-04A-1 SECTION 303-04A Fuel Charging and Controls — 2.5L Duratec-HE (122kW/165PS) - MI4 VEHICLE APPLICATION: 2011.50 Ranger CONTENTS PAGE DESCRIPTION AND OPERATION Fuel Charging and Controls 303-04A-2 REMOVAL AND INSTALLATION Fuel Rail Throttle Body (23 198 0) 303-04A-4 303-04A-6 Fuel Charging and Controls — 2.5L Duratec-HE (122kW/165PS) 303-04A-2 303-04A-2 - MI4 DESCRIPTION AND OPERATION Fuel Charging and Controls Item Part Number Description Item Fuel rail Fuel injector 2011.50 Ranger Part Number Description Fuel injector retaining clip - Fuel injector O-ring seals G1434275en Fuel Charging and Controls — 2.5L Duratec-HE (122kW/165PS) 303-04A-3 - MI4 303-04A-3 DESCRIPTION AND OPERATION Item Description Throttle body Throttle Body The throttle plate position is controlled by a signal from the powertrain control module (PCM) which receives an input from the accelerator pedal position (APP) sensor The system is fully electronic and does not use any cables The signal from the PCM is used to control a DC motor within the throttle body which is connected to the throttle plate through gears The throttle body also gives inputs back to the PCM This information allows the PCM to compensate for factors such as carbon build up within the throttle body and throttle body wear The throttle body also provides information to the PCM to enable the flagging of a diagnostic trouble code (DTC) 2011.50 Ranger G1434275en Fuel Charging and Controls — 2.5L Duratec-HE (122kW/165PS) 303-04A-4 303-04A-4 - MI4 REMOVAL AND INSTALLATION Fuel Rail Materials Name Specification Engine Oil - 5W-30 WSS-M2C913-C Removal NOTE: Removal steps in this procedure may contain installation details Refer to: Gasoline and Gasoline-Ethanol Fuel Systems Health and Safety Precautions (100-00 General Information, Description and Operation) Refer to: Intake Manifold (303-01 Engine - 2.5L Duratec-HE (122kW/165PS) - MI4, Removal and Installation) Refer to: Fuel System Pressure Release (310-00 Fuel System - General Information 2.5L Duratec-HE (122kW/165PS) - MI4, General Procedures) Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures) Torque: 10 Nm 2011.50 Ranger G1272502en Fuel Charging and Controls — 2.5L Duratec-HE (122kW/165PS) 303-04A-5 303-04A-5 - MI4 REMOVAL AND INSTALLATION Torque: 23 Nm 10 CAUTION: Only use the specified material to lubricate the seals Material: engine oil WSS-M2C913-C (Engine Oil - 5W-30) Installation To install, reverse the removal procedure 2011.50 Ranger G1272502en Fuel Charging and Controls — 2.5L Duratec-HE (122kW/165PS) 303-04A-6 303-04A-6 - MI4 REMOVAL AND INSTALLATION Throttle Body(23 198 0) Removal NOTE: Removal steps in this procedure may contain installation details NOTE: The gasket is to be reused unless damaged Torque: 10 Nm Installation To install, reverse the removal procedure NOTE: Make sure that the pedals remain in the rest position during the initialization Turn the ignition key to position II and wait for one minute to initialize the throttle body Turn the ignition key to the OFF position 2011.50 Ranger G1272503en