The VLSI Handbook P1

... Chen The Communications Handbook, Second Edition, Jerry Gibson The Computer Engineering Handbook, Vojin G. Oklobdzija The Control Handbook , William S. Levine The CRC Handbook ... The Ocean Engineering Handbook , Ferial El-Hawary The RF and Microwave Handbook , Mike Golio The Technology Management Handbook , Richard C. Dorf The Transforms and Appli...

Ngày tải lên: 27/10/2013, 22:15

... of the speed of the output shaft and utilizing the motion of the flyball to control the valve, the amount of steam entering the engine is controlled. As the speed of the engine increases, the ... vehicle) by integrating the sensor with the cruise control and ABS systems. The driver is able to set the speed and the desired distance between the cars ahead of him....

Ngày tải lên: 19/10/2013, 18:15

... added profile control. The integral of the base doping over the base width is known as the Gummel number. The current gain of the transistor is determined by the ratio of the Gummel number in the emitter ... 2006 5:57 PM 1-14 The VLSI Handbook © 2006 by CRC Press LLC of the interface between the polysilicon layer and the monosilicon substrate [48]. Hence, the cl...

Ngày tải lên: 06/11/2013, 08:15

... minimize the ratio of the impedance looking from the voltmeter to the impedance of the test circuit. The LC circuit is then tuned to resonate and the resultant voltage measured. The value of Q may then ... Grasp the conductor in the right hand with the thumb extending along the conductor pointing in the direction of the current. With the fingers partly closed, th...

Ngày tải lên: 25/01/2014, 13:20

... advertisers in the firm devised ways of selling them to the public. With the marketing concept, the story is supposed to start with the consumer. Consumers have the power to shape their own wants without ... opinions of the respondents and the observer. The report is usually a highly selective account of the discussion, which is edited to illustrate the main thesis of t...

Ngày tải lên: 27/08/2012, 09:57

... learned from the past, inspiration and creativity for the state-of -the- art of the present, and insightful visions for the future. This text then equally represents a kind of status report of the various ... The editor, as one of the contributing authors, has aptly summarized the content broadly as “about product variation.” The contained chapters proceed then to wend their...

Ngày tải lên: 19/10/2013, 19:15

... routine. The first parameter is the file handle to write the data to. The data to write is specified as the second parameter. Finally, the third parameter is the length of the data to write. Like this: ... Connection The listen( ) function tells the operating system that the server is ready to accept incoming network connections on the port. The first parameter is...

Ngày tải lên: 20/10/2013, 10:15

... Global Knowledge, for their generous access to the IT industry’s best courses, instructors and training facilities. Ralph Troupe and the team at Rt. 1 Solutions for their invaluable insight into the challenges ... 43 Introduction to Network Administration 44 Designing and Setting Up the Network 45 Managing the Network 46 Protecting the Network 46 Documenting the Network 48 Micr...

Ngày tải lên: 23/10/2013, 15:15

... comparable DC drive. The next step was the introduction of the vector- controlled methods. The goal of these methods is to make the induction machine emulate the DC machine by transforming the stator currents ... MMF vector that rotates at the frequency of the stator currents. The length of the vector is dependent upon the magnitude of the MMF vectors. Observing the...

Ngày tải lên: 23/10/2013, 16:15

... motor are the torque per unit volume of the motor, the operating temperature range, and the severity of the operational duty of the magnet [2]. For maximum power density, the product of the electric ... maintenance and the sparking associated with them. Having the armature windings on the stator helps the conduction of heat from the windings. Because there are no win...

Ngày tải lên: 23/10/2013, 16:15