... đồ khối quét dòng, Hư hỏng thường gặp của khối quét dòng, nguyên nhân và phương pháp kiểm tra sửa chữa 1. Nhiệm vụ của khối quét dòng Nhiệm vụ chính của khối quét dòng là tạo ra các mmức
... unlocking condi-
tion.
3. Cut and pry off the side panel outer.
S Cut at the rear pillar and side outer(rear side of frame
door opening) along the bold lines as shown with a hand-
saw and snips ... necessary, remove the fuel tank and off
lines.
2. Pull out and straighten the damaged area to approxi-
mately the original shape.
S Attach the car to the frame straightener by tightening the
underb...
... gồm 3 chương:Chương 1 - Kết cấu hạ tầng Đường Sắt và kế hoạch quản lý, sửa chữa, bảo trì kết cấu hạ tầng Đường Sắt.Chương 2 - Tình hình thực hiện kế hoạch quản lý, sửa chữa, bảo trì kết cấu hạ ... năm đầu của kế hoạch 5 năm 2006 – 2010. Chương 3 - Giải pháp đảm bảo thực hiện kế hoạch quản lý, sửa chữa, bảo trì kết cấu hạ tầng Đường Sắt giai đoạn 2008 – 2010Các số liệu sử...
... information.
.
CAUTION : Detailed descriptions of standard work-
shop procedures, safety principles and service op-
erations are not included. Please note that this manu-
al does contain warnings and cautions against ... not could GM DAEWOO in-
vestigate all such ways. Anyone using service proce-
dures or tools, whether or not recommended by GM
DAEWOO, must satisfy himself thoroughly that nei...
... level of quality.
.
When bodywork is damaged, the customer rightly ex-
pects it to be expertly repaired to the same quality stan-
dards.
.
At the same time, for his safety, the customer expects
you ... knowledge of materials,
measuring and straightening methods, possible distor-
tion, optimum corrosion prevention and much more be-
sides.
.
This publication is designed to help you update your...
... sections
come apart?
3. Are there any creases or distortion in the front wheel-
house or side frame? Have any of the connected sec-
tions come apart?
4. Is there any bending or twisting of the whole front
area?
5. ... there any oil or water leakage and damage to the en-
gine, transmission or brakes?
12. Is there any irregular noise in the gear changing opera-
tion, engine and transmission rot...
... 1.6mm
Minimum inter-
vals
11mm 16mm 20mm 24mm
Fig. 2
Fig. 1 Welders
NUBIRA/LACETTI WELDING AND TOOLS 3–3
S Plate thickness and tip diameter
Plate thickness 0.6mm 0.9mm 1.2mm 1.6mm
Minimum inter-
vals
4.5Ø ... performing spot welding, make absolutely sure
that you conform to the conditions governed by the cur-
rent, conductivity time, welding pressure, holding time,
and shutdown time recommend...
... and grease re-
mover.
.
4. Coat with primer.
Note : Apply to bare
sheet metal and put-
tied area.
Epoxy–based primer and harden-
er, epoxy thinner.
S Mix and thin the primer accord-
ing to the ... accord-
ing to the manufacturer’s direc-
tions.
Apply 2–4 coats, allowing sufficient flash time
between coats.
Force dry at 60–70RC(140–158RF) for at
least 30 minutes.
Spray to
a thick-
ness ... the...