Sửa chữa DAEWOO-LACETTI 2010 - P12

Ngày tải lên: 30/10/2012, 08:47

... gồm 3 chương:Chương 1 - Kết cấu hạ tầng Đường Sắt và kế hoạch quản lý, sửa chữa, bảo trì kết cấu hạ tầng Đường Sắt.Chương 2 - Tình hình thực hiện kế hoạch quản lý, sửa chữa, bảo trì kết cấu hạ ... năm đầu của kế hoạch 5 năm 2006 – 2010. Chương 3 - Giải pháp đảm bảo thực hiện kế hoạch quản lý, sửa chữa, bảo trì kết cấu hạ tầng Đường Sắt giai đoạn 2008 – 2010Các số liệu sử...

Ngày tải lên: 08/09/2012, 13:39

... colours 90GENERALPaintwork products used 90GENERALPaintwork products used 90GENERALSealing and anti-gravel products 90GENERALSealing and anti-gravel products 90GENERALThe concept of colour 90GENERALThe concept of colour 90GENERALThe

Ngày tải lên: 22/10/2012, 15:42

... information. . CAUTION : Detailed descriptions of standard work- shop procedures, safety principles and service op- erations are not included. Please note that this manu- al does contain warnings and cautions against ... not could GM DAEWOO in- vestigate all such ways. Anyone using service proce- dures or tools, whether or not recommended by GM DAEWOO, must satisfy himself thoroughly that nei...

Ngày tải lên: 30/10/2012, 08:47

... level of quality. . When bodywork is damaged, the customer rightly ex- pects it to be expertly repaired to the same quality stan- dards. . At the same time, for his safety, the customer expects you ... knowledge of materials, measuring and straightening methods, possible distor- tion, optimum corrosion prevention and much more be- sides. . This publication is designed to help you update your...

Ngày tải lên: 30/10/2012, 08:47

... sections come apart? 3. Are there any creases or distortion in the front wheel- house or side frame? Have any of the connected sec- tions come apart? 4. Is there any bending or twisting of the whole front area? 5. ... there any oil or water leakage and damage to the en- gine, transmission or brakes? 12. Is there any irregular noise in the gear changing opera- tion, engine and transmission rot...

Ngày tải lên: 30/10/2012, 08:47

... 1.6mm Minimum inter- vals 11mm 16mm 20mm 24mm Fig. 2 Fig. 1 Welders NUBIRA/LACETTI WELDING AND TOOLS 3–3 S Plate thickness and tip diameter Plate thickness 0.6mm 0.9mm 1.2mm 1.6mm Minimum inter- vals 4.5Ø ... performing spot welding, make absolutely sure that you conform to the conditions governed by the cur- rent, conductivity time, welding pressure, holding time, and shutdown time recommend...

Ngày tải lên: 30/10/2012, 08:47

... and grease re- mover. . 4. Coat with primer. Note : Apply to bare sheet metal and put- tied area. Epoxy–based primer and harden- er, epoxy thinner. S Mix and thin the primer accord- ing to the ... accord- ing to the manufacturer’s direc- tions. Apply 2–4 coats, allowing sufficient flash time between coats. Force dry at 60–70RC(140–158RF) for at least 30 minutes. Spray to a thick- ness ... the...

Ngày tải lên: 30/10/2012, 08:47

... Therefore, replace- ment of the component affects the front wheel align- ment and maintains the rigidity of the front section. When assembling it, either use a jig or follow dimen- sions on the ... locator shockabsorber. Therefore, replace- ment of the component affects the front wheel align- ment. When assembling it, either use a jig or follow di- mensions on the body repair chart for positi...

Ngày tải lên: 30/10/2012, 08:47

... vehicle’s outer appearance. Before replac- ing the roof, make sure that the body is horizontal. Be- fore welding the roof panel, adjust the frame door open- ing flanges so that they contact the ... spot welds with disc sander and repair all cracks, holes or other de- fects by welding also repair the rear longitudinal and ex- tension rear longitudinal if necessary. CAUTION : To prevent eye ......

Ngày tải lên: 30/10/2012, 08:47