IADC Drilling Manual Part 3 pdf

... Contractors IADC Drilling Manual - Eleventh Edition MAXIMUM TORSIONAL LOAD (ft-lbs) 3- 1/2" 20 160 15 36 0 13 130 4" 25 480 19 690 16 930 4-1/2" 33 31 0 25 740 22 150 5" 44 750 34 ... Nom. Wall) 3- 1/2" 297 660 230 490 198 30 0 4" 31 3 490 244 640 211 35 0 4-1/2" 37 3 520 291 570 251 890 5" 442 420 34 5 910 299 160 B-144 Inter...

Ngày tải lên: 11/08/2014, 08:21

... Z-26 IADC Glossary - S Z -30 IADC Glossary - T Z -34 IADC Glossary - U Z -36 IADC Glossary - V Z -36 IADC Glossary - W Z -36 IADC Glossary - X Z -38 IADC Glossary - Y Z -38 IADC Glossary - Z Z -38 5 International ... Glossary Z-1 IADC Glossary - A Z -3 IADC Glossary - B Z-4 IADC Glossary - C Z-7 IADC Glossary - D Z-10 IADC Glossary - E Z- 13 IADC Glossary - F Z-...

Ngày tải lên: 11/08/2014, 08:21

... designation of 30 (516, 37 .1). A rectangular mesh screen with mesh counts of 70 x 30 , openings of 160 x 500 microns, and open area of 33 .5 percent would have a designation of 70 x 30 (160 x 500, 33 .5). ... Association of Drilling Contractors IADC Drilling Manual - Eleventh Edition Flow Rate Conversions V-62 International Association of Drilling Contractors IADC Drilling...

Ngày tải lên: 11/08/2014, 08:22

... string washout. B -30 International Association of Drilling Contractors IADC Drilling Manual - Eleventh Edition Figure B1-15 Figure B1-16 Figure B1-17 B-12 International Association of Drilling Contractors IADC ... pin with the information shown in Figure B1 -3. B-50 International Association of Drilling Contractors IADC Drilling Manual - Eleventh Edition Table B2 -3 C...

Ngày tải lên: 11/08/2014, 08:21

... Contractors IADC Drilling Manual - Eleventh Edition Figure D1 -3 Bending Strength Ratios of 1-1/2" and 1 -3/ 4" Drill Collars D-22 International Association of Drilling Contractors IADC Drilling Manual ... of Drilling Contractors IADC Drilling Manual - Eleventh Edition Table D3-1a Hexagon Kellys - Drive Section Table D3-1b Hexagon Kellys - Upper Box Connection...

Ngày tải lên: 11/08/2014, 08:21

... Table G1-3a and G1-3b F-14 International Association of Drilling Contractors IADC Drilling Manual - Eleventh Edition E-12 International Association of Drilling Contractors IADC Drilling Manual ... manufacturer. F-8 International Association of Drilling Contractors IADC Drilling Manual - Eleventh Edition Tables Related to Brake Rim Wear: Tables F-xx E- 23 International...

Ngày tải lên: 11/08/2014, 08:21

... Association of Drilling Contractors IADC Drilling Manual - Eleventh Edition Figure J3-4 File-Gard Rod in Corrosive Drilling Fluid FIGURE J3-4: This File-Gard rod was run in a corrosive drilling fluid. Notice ... System J- 13 I. Suction Mud System J- 13 II. Discharge System J-17 III. Drilling Fluids And Their Effect On Expendable Pump Parts J-18 J -3 Pump Parts, Theory and Fun...

Ngày tải lên: 11/08/2014, 08:21

... required at the lowest speed. K-28 International Association of Drilling Contractors IADC Drilling Manual - Eleventh Edition a. Before drilling out any casing shoe, test entire casing to operator's ... plug. J-95 International Association of Drilling Contractors Chapter J: Pumps This Page Left Intentionally Blank K-12 International Association of Drilling Con...

Ngày tải lên: 11/08/2014, 08:22

... of Drilling Contractors IADC Drilling Manual - Eleventh Edition Table K1-8-7 Cameron Ram BOPs - Operating Characteristics K-88 International Association of Drilling Contractors IADC Drilling Manual ... above pre-charge pressure. Therefore; Minimum System Pressure = 233 5 + 200 = 2 535 psi Maximum System Pressure = 233 5 + 2000 = 433 5 psi The stored usable fluid in our subsea...

Ngày tải lên: 11/08/2014, 08:22

... of Drilling Contractors IADC Drilling Manual - Eleventh Edition Cut-Off Program For 1 -3/ 8" Rotary Drilling Line; Goal of 24.0 T-M/Ft Cut Table - M5-p13b Wire Rope Cut-off Program, 1 -3/ 8" ... used following this particular program. M-72 International Association of Drilling Contractors IADC Drilling Manual - Eleventh Edition Cut-Off Program For 1 -3/ 8" Rot...

Ngày tải lên: 11/08/2014, 08:22