... addition to this manual. • The Operator’s Manual • The Parts Catalog • Operation Manual of the Engine • Parts Catalog of the Engine • Hitachi Training Material MANUAL COMPOSITION ... READER • This manual is written for an experienced technician to provide technical information needed to maintain and repair this machine. • Be sure to thoroughly read this manual for cor-rect ... Material MANUAL COMPOSITION • This manual consists of three portions: the Techni-cal Manual (Operational Principle), the Technical Manual (Troubleshooting) and the Workshop Man-ual....
... type and concentration of antifreeze.19 Do not use engine antifreeze in the screenwasher system, as it will cause damage to thevehicle paintwork. Screen wash antifreeze isavailable from most ... against frost,rust and corrosion.18 After filling with antifreeze, a label shouldbe attached to the radiator stating the type ofantifreeze and the date installed. Anysubsequent topping-up should ... Super Plusantifreeze is used for filling and topping-up, asit has been specially formulated for use inFord mixed metal engines (see “Lubricantsand fluids”).17 A solution of 45% antifreeze must...
... CONSUMABLESPackaging04•"CIRCUIT PLUS"Varnish for the repair of heated rear screens•"CONTACT PLUS"Varnish for the repair of heated rear screen sup-ply tabsBottleKit77 01 ... gasketto settle.2) Cylinder head tightening:- slacken bolt by bolt until they are complete-ly free then tighten all of the bolts to 2.5daN.m, then carry out an angular tighteningof 108° ± ... ADJUSTABLEPARALLELISMUNLADENUNLADENAdjusted byrotating track rodsleeves1 turn= 30’(3 mm)- - MANUAL STEERINGALL TYPES EXCEPT B539 - C539 - L539 - B53D - C53D - D53D - L53D07(Toe-out)For...
... incorporated in the computer via the load potentiometer. In the event of afault refer to workshop repairmanual T.A. M.POSITION OF FOOT1 → 22 → 33 → 22 → 1No-load (PL) 23 40 27 15Full-load ... fitting the differential sealB.Vi.1058 Plug for fitting the differential seal91755R85965R21-29 MANUAL GEARBOXESGearbox (Removal - Refitting)21Remove the three bolts securing the rear centremounting ... side-member and the engine cradle.Raise the engine.Turn the gearbox to the front slightly so as to free the final drive section then remove the gearboxfrom the vehicle.After uncoupling the gearbox...
... compensatoradjustment checkReplacement of compensatorFault chartSTEERINGAxial ball joints Manual steering boxAnti-rattle bearing on manual steering boxPower assisted steering boxSteering box plungerSteering ... care notto damage the driveshaft gaiter.Place the upper cup bolts in the appropriate holes.A manual steeringB power steeringTighten, to torque :- the shock absorber lower mounting bolts ... TYRESSTEERINGMECHANICAL ELEMENT CONTROLS77 11 190 850 NOVEMBER 1996 Edition Anglaise"The repair methods given by the manufacturer in this document are based on thetechnical specifications...
... operate?yesyesnono yes Repair the wiringbetween track B3of connection R34and track A1 of thepressostat. Repair the wiring betweentrack B3 of connection R34and the fuse box. Repair the wiringbetween ... R99.Track B4 on connector R99 and vehicle earthM11.yes Repair the wiring between track A1 ofconnector R99 and track 1 on relay 690.yes Repair the wiring between track A1 on blackconnector R99 ... this is the case, remove the compressorand check its oil level (see method in the A/Cworkshop repair manual) , drain the oil in thepipes and the condenser, change the dehydratingbottle and adjust...
... the mastic)then free it from the upper rubbing strip.NOTE: when changing a door or the trim, trimsealing mastic part number 77 01 421 049 must bereapplied (see "BODYWORK REPAIRS" ... centre pillar (1) see section 71 B- the mounting screws,- the lower seat belt mounting.By hand, free the rear part of the trim from the surrounding seal and remove clips (B).Proceed in the same ... which is held by 4 screws,- the 4 screws holding the speaker mounting,- the mounting (6) and free the storagecompartment from the lower snap fastenings(7), by pushing it upwards.Disconnect...
... MOUNTINGDuring repairing of the rear, with the rear sub-frame removed, the jig allows positioning of the1/2 unit (assembled wheel arch).92638SFUEL TANK MOUNTING CROSS MEMBERDuring repairing of ... positioning of the fuel tank crossmember. 92639S92640SREAR SIDE MEMBER REAR END PANELDuring repairing of the rear, the jig allowspositioning of the side member or the rear unit. 40-37GENERALLifting40LASHING ... line: L - D - B (position of body jig bench bracket at Z, in relation to this line).The bodywork repair body jig brackets and their positions on the bench are designed in accordance withthese...