Tài liệu DSX Modular Rear Cross-Connect RZX-3 Modules doc

10/03 • 100571 600 mm Products 111 www.adc.com • +32-2-712-65-00 • +32-2-712-65-42 DSX Modular Rear Cross-Connect RZX-3 Modules RZX-3 is designed as a total system solution – not just components. Focused on simplifying the solution, the system approach provides ease of expansion, streamlines cross-connect jumper installation and reduces premature jumper exhaustion. And with one part number ordering, engineering, purchasing and installation labor is greatly reduced. Highest Density With the possibility of 336 midsize jack ports utilizing BNC connector interfaces in a 2.2 m rack, the new RZX-3 has more capacity than any other midsize DSX available. Cable Management Superior cable management all within the 600 mm footprint. Flexibility With its “plug and play” architecture, the RZX-3 system is fully modular throughout chassis, circuit frames and jacks. Individual BNC circuit frames remove easily from the chassis, providing the most simplified and cost-effective restoral capabilities available. Durability ADC’s robust DSX jack is constructed with mechanical support to ensure long service life, unlike the lower quality solder-type connections on a printed circuit board often found in other systems. The die-cast coaxial jacks are rigorously tested with over 10,000 insertion/withdrawal cycles. The solid cylinder design has a closed entry contact to prevent spring contact overstress. Reliability ADC doesn't use Teflon insulators, ensuring true 75 Ohm impedance. RZX-3’s sealed jack has firewall protection preventing environmental contaminants from disturbing switch contacts. Make-Before-Break Switching Contacts Make-before-break contacts ensure that high speed signals never go open or unterminated during in- service patching. DS3 signals are always terminated to a 75 Ohm load, preventing signal oscillation that can lead to bit errors during patching. RZX-3 Chassis 10/03 • 100571 600 mm Products 112 www.adc.com • +32-2-712-65-00 • +32-2-712-65-42 Each module provides an IN and OUT switching jack for direct access to the network element’s input and output signals. These jacks provide a means to temporarily break the connection between network elements that are cross-connected together and allow access to the signals for test and patching operations. A MONITOR jack with a high impedance bridge network (21.5 dB below the active signal) is connected to the OUT jack for nonintrusive access to the output signal of each network element. 3-Port: IN and OUT switching jacks and a single MONITOR jack 4-Port: IN and OUT switching jacks and a dual MONITOR jack 6-Port: IN and OUT switching jacks and a dual MONITOR jack The rear cross-connect modules have jacks for temporary access on the front of the modules, permanent equipment cable interface connections on the rear of the modules, and semi-permanent cross-connect interface connections on the rear of the modules. RZX-3 modules have rear BNC or 1.6/5.6 connectors staggered high and low across the chassis in order to obtain the ultimate in system density. Modules may be ordered individually or in multipack kits. Module kits include a combination of BNC or 1.6/5.6 high and BNC or 1.6/5.6 low modules. DSX Modular Rear Cross-Connect RZX-3 Modules Description Dual monitor Single monitor Dual monitor Dual monitor Odd Chassis Position DSX-4R-MB160 DSX-4R-MG130 DSX-4R-MG140 DSX-4R-MG160 Even Chassis Position DSX-4R-MB260 DSX-4R-MG230 DSX-4R-MG240 DSX-4R-MG260 Ordering Information Module Type 6-port module, BNC 3-port module, 1.6/5.6 4-port module, 1.6/5.6 6-port module, 1.6/5.6 3 Port Module 4 Port Module 3-Port — provides monitoring to OUT jack only 4-Port — provides monitoring for both IN and OUT jacks Module Rear View IN MONITOR MONITOR OUTOUT MONITOR IN MONITOR MONITOR IN OUT X-OUT X-IN 6-Port — provides monitoring for both IN and OUT jacks and access to the cross-connect 10/03 • 100571 600 mm Products 113 www.adc.com • +32-2-712-65-00 • +32-2-712-65-42 The RZX-3 rear cross-connect system supports 24 terminations in a single chassis. For easy circuit identification, LEDs are mounted on the front and the rear of the chassis. The chassis has a rear cable tray to accommodate maximum cable density. DSX Modular Rear Cross-Connect RZX-3 Chassis Description Empty chassis accommodates 24 terminations Catalog Number DSX4R-D24 Ordering Information Features • Empty classes mounts in 600 mm DSX-3 skeleton bay (IBR-3RSC001) • Red flashing LED on front and rear of the chassis for easy circuit identification • Rear cable tray to accommodate the maximum cable density Each position of the preterminated chassis is equipped with a circuit frame including BNC receptacles. Network elements are cabled during initial installation. When service turn-up is required, a jack kit is plugged into the circuit frame to complete the circuit and provide jack access for testing and patching. Each jack kit consists of an upper and lower jack. Preterminated Option Description Preterminated chassis Allows network elements to be cabled to the chassis without deploying the jacks. This allows the cost of jacks to be deferred until revenue is generated. Ordering Information Catalog Number DSX4R-24B0-D24 RZX-3 Chassis 10/03 • 100571 600 mm Products 114 www.adc.com • +32-2-712-65-00 • +32-2-712-65-42 ADC offers skeleton bays, preassembled bays with all cable and jumper management, but no chassis or modules. Preprovisioning all cable management ensures that existing jumpers need never be touched when chassis are added to the bay. Jumper routing is never restricted since all wireways are preprovisioned. DSX Modular Rear Cross-Connect RZX-3 Skeleton Bay The end guard offers protection and a finished appearance to the beginning and end of the lineup. RZX-3 End Guard Description 600 mm skeleton bay Preassembled with all cable and jumper management. The frame supports 14 chassis or a total of 336 terminations. Chassis and modules are ordered separately. Ordering Information Catalog Number IBR-D3S002 Description RZX-3 end guard Catalog Number RAC-0B0748 Ordering Information 10/03 • 100571 600 mm Products 115 www.adc.com • +32-2-712-65-00 • +32-2-712-65-42 Features • Provides bidirectional, nonintrusive signal testing • Supports E1 (2.048 Mbps), E3 (34.368 Mbps), or STM-1 (155.52 Mbps) signal rate applications • Modular design allows for capital investment to coincide with revenue growth • Mounts in standard 600 mm bays • Quality cable management and circuit identification markings Digital Distribution Frame System Application The Digital Distribution Frame system (DDF) is used primarily in collocation environments and customer premises as a connection point between NEs. Each NE is semi-permanently cabled to IN/OUT connectors in either the front or rear of each module. The digital signal is accessed through the two MON OUT connectors on the front of each module for testing and monitoring. These dual monitor ports allow access to both directions of the circuit from a single location. This saves valuable technician time when the other side of the termination is located far away, in another room, or is inaccessible. Network Element A Tx OUT OUT IN Rx IN Network Element Z Tx OUT Rx IN DMM MON Z-OUT MON A-OUT OUT IN Test Unit 10/03 • 100571 600 mm Products 116 www.adc.com • +32-2-712-65-00 • +32-2-712-65-42 Features • Front, dual monitor ports on all module styles • BNC or 1.6/5.6 connectors provide true 75 Ohm characteristic impedance • All module styles are compatible with any DMM 600 mm chassis style DMM-BBNCMF Rear and Front View DMM-BBNCF Rear and Front View DMM-BBNCBLK Rear and Front View DMM-1656MF Rear and Front View DMM-1656F Rear and Front View DMM-1656BLK Rear and Front View Connector Type BNC BNC BNC bulkhead 1.6/5.6 1.6/5.6 1.6/5.6 bulkhead Blank plate Catalog Number DMM-BBNCMF DMM-BBNCF DMM-BBNCBLK DMM-1656MF DMM-1656F DMM-1656BLK DMM-BLANK IN/OUT Connector Locations Rear Front and Rear Front and Rear Rear Front and Rear Front and Rear N/A Ordering Information Digital Distribution Frame System Modules 10/03 • 100571 600 mm Products 117 www.adc.com • +32-2-712-65-00 • +32-2-712-65-42 Digital Distribution Frame System Standard Configuration D3C-0024T Front View Features • 288 total circuits in fully loaded bay • Cable bars and front cable trays, with cable tie- downs, reduce cable congestion and simplify maintenance • Circuit designation labels above connectors and on cable tray ensure proper cable routing and identification • Bay equipped with cable troughs, vertical wiring ducts, and equipment cable tie-down bars • Zone 4 earthquake-rated rack with EIA mounting spacing Description Unloaded chassis Accommodates up to 24 modules 600 mm skeleton bay Accommodates up to 12 chassis Catalog Number D3C-0024T IBR-D3C002 Dimensions (HxWxD) 113 x 482.6 x 228.6 mm (4.4" x 19" x 9") 2200 x 600 x 475 mm (86.6" x 23.6" x 18.7") Ordering Information IBR-D3C002 Side View 475 mm (18.7") 600 mm [23.6] 2200 mm [86.6] 449.6 mm [17.7] 1 5 10 15 20 25 30 35 40 45 LOWER CABLE TROUGH UPPER CABLE TROUGH RESERVED FOR MISCELLANEOUS APPLICATIONS IBR-D3C002 Front View 10/03 • 100571 600 mm Products 118 www.adc.com • +32-2-712-65-00 • +32-2-712-65-42 Digital Distribution Frame System Wall Mount Box D3C-WBOX06 Front View Features • Used as a demarcation point when NEs are supplied by the service provider and by the customer • Separate locks on each door secure connections from unwanted access Description Unloaded wall mount box Accommodates up to 6 modules Catalog Number D3C-WBOX06 Dimensions (HxWxD) 267 x 203 x 114 mm (10.5" x 8" x 4.5") Ordering Information Note: Modules are ordered separately Specifications ELECTRICAL Insertion Loss: Better than 5 dB, 100 KHz to 100 MHz Better than 8 dB, 100 MHz to 300 MHz Return Loss: Better than -20 dB, 100 KHz to 300 MHz Monitor Loading Effect: < .4 dB change in insertion loss to 300 MHz Monitor Level: 21.5 ± 1.5 dB, 100 KHz to 300 MHz Isolation: < -55 dB at 22.368 MHz Cross Talk: < -55 dB at 22.368 MHz Phase Delay < 4 nanoseconds to 300 MHz Pulse Template: Conform to CCITT Recomm. G.703 MECHANICAL Retention Force: 7 lbs. minimum Retention Torque: 4" per lbs. minimum ENVIRONMENTAL Thermal Shock: -40ºC to +60ºC operating -55ºC to +85ºC non-operating Moisture Resistance: 0% to 95% 10/03 • 100571 600 mm Products 119 www.adc.com • +32-2-712-65-00 • +32-2-712-65-42 DSX-3 Patch Cords PCH-MMXB-003 Description DSX-3 patch cords Used to patch between DSX-3 jacks • Midsize plugs • With RG59 type cable Catalog Number PCH-MMXB-XXX Replace XXX with desired patch cord length (001 to 050 feet). DSX-3 Patch Cords (with RG59 type cable) Ordering Information Factory-Terminated Rear Cross-Connect Jumpers Catalog Number XCC- ___ ___ X ___ - ___ *Standard Jumper Lengths: 3', 6', 9', 12', 15', 18', 20', 25', 30', 35', 40', 45', 50' (.92, 1.83, 2.75, 3.66, 4.58, 5.49, 6.1, 7.63, 9.15, 10.68, 12.2, 13.73, 15.25 m) Ordering Example: Catalog number XCC-BBXD-015: 15' (4.58 m) dual cross-connect jumper using 735 type coaxial cable with tracer messenger wire, (2) BNC connectors and tracer pin factory-terminated on both ends of cable. Connector Interface Type on First End of Jumper Factory-terminated BNC connector Factory-terminated 16./5.6 connectors B G Coaxial Cable Type C Single 735 with tracer messenger wire (4J, 4U, 4H, 4M compatible) D Dual 735 with tracer messenger wire Jumper Length* XXX Length in feet (001 thru 050) Connector Interface Type on Second End of Jumper Factory-terminated BNC connector Factory-terminated 1.6/5.6 connectors B G XCC-BBXD-003 Connector(s) and tracer pin(s) factory-terminated on both ends. Catalog Number PHC - ___ ___ X ___ - ___ *Standard Patch Cord Lengths: 3', 6', 9', 12', 15', 18', 20', 25', 30', 35', 40', 45', 50' (.92, 1.83, 2.75, 3.66, 4.58, 5.49, 6.1, 7.63, 9.15, 10.68, 12.2, 13.73, 15.25 m) Connector Interface Type on First End of Patch Cord Factory-terminated BNC connector Factory-terminated 16./5.6 connectors B G Coaxial Cable Type C Single 735 with tracer messenger wire (4J, 4U, 4H, 4M compatible) D Dual 735 with tracer messenger wire Patch Cord Length* XXX Length in feet (001 thru 050) Connector Interface Type on Second End of Patch Cord Factory-terminated BNC connector Factory-terminated 1.6/5.6 connectors B G Ordering Example: Catalog number PHC-BBXD-015: 15' (4.58 m) dual cross-connect jumper using 735 type coaxial cable with (2) BNC connectors terminated on both ends of cable. Factory-Terminated Patch Cords 10/03 • 100571 600 mm Products 120 www.adc.com • +32-2-712-65-00 • +32-2-712-65-42 TNC-3 DSX-3 Accessories BNC-RA-3 *In addition to the .042" square pin crimp, all connectors listed above are compatible with a 12 point method of crimping. BNC-3 Catalog Number Straight BNC Connectors BNC-3 BNC-7 BNC-2 BNC-1 BNC-4 Right Angle BNC Connectors BNC-RA-3 BNC-RA-7 BNC-RA-2 BNC-RA-1 BNC-RA-4 Straight TNC Connectors TNC-3 TNC-7 TNC-2 TNC-1 TNC-4 Cable Type 735A 0222 RG59 734 728 735A 0222 RG59 734 728 735A 0222 RG59 734 728 Outer Jack Diameter 0.127" 0.155" 0.241" 0.236" 0.305" 0.127" 0.155" 0.241" 0.236" 0.305" 0.127" 0.155" 0.241" 0.236" 0.305" Center Conductor 26 gauge 24 gauge 23 gauge 20 gauge 20 gauge 26 gauge 24 gauge 23 gauge 20 gauge 20 gauge 26 gauge 24 gauge 23 gauge 20 gauge 20 gauge Sleeve 0.178" 0.197" 0.255" 0.255" 0.324" 0.178" 0.197" 0.255" 0.255" 0.324" 0.178" 0.197" 0.255" 0.255" 0.324" Center Pin* 0.042" 0.042" 0.042" 0.042" 0.042" 0.042" 0.042" 0.042" 0.042" 0.042" 0.042" 0.042" 0.042" 0.042" 0.042" Cable Dimensions Connector Crimp Ordering Information Ordering Information Catalog Number PGS-110005 PGS-110006 Description Tracer pin and sleeve – 1 each Tracer pin and sleeve – 100 piece kit Coaxial Connectors Tracer Pins [...].. .DSX- 3 Accessories Tool Kit Ordering Information Catalog Number Description BNC-TOOL-1 600 mm Products Connection tool kit Includes: • Crimp tool (WT-2) • BNC crimp die set for 735, RG59 and 734 cables... (BT2000) • Carrying case BNC-TOOL-1 Coaxial Tools Ordering Information Catalog Number Description 100571 • LCA-000009 Insertion/withdrawal tool BNC connector TNC connector BT2000 TT1000 Coaxial cable cutter DSX- 3 CCUT Crimp tool 10/03 Adjustable cable termination tray for 19" or 23" chassis WT-2 Crimp die set for WT-2 tool 735, RG59 and 734 cables 0222 cable RG59, 734 and 728 cables WD-2 WD-3 WD-1 Stripping... or TNC connector 735A/0222 cables RG59/734 cables 728 cables STC-13B STC-12B STC-11B Replacement cassette (black) for BNC or TNC connector 735A/0222/RG59/734/728 cables CCS-BLK LCA-000009 BT2000 TT1000 DSX- 3 CCUT WT-2 STC-13B www.adc.com • +32-2-712-65-00 • +32-2-712-65-42 121 . Products 111 www.adc.com • +32-2-712-65-00 • +32-2-712-65-42 DSX Modular Rear Cross-Connect RZX-3 Modules RZX-3 is designed as a total system solution – not just. connections on the rear of the modules, and semi-permanent cross-connect interface connections on the rear of the modules. RZX-3 modules have rear BNC or 1.6/5.6