Tài liệu Reinforcing the Cabinet pptx

OptiX OSN 3500 Installation Manual Contents Contents 5 Reinforcing the Cabinet 1 5.1 Combining the Adjacent Cabinets 2 5.2 Reinforcing the Cabinet to the Cabling Frame 4 5.2.1 Reinforcement Mode 4 5.2.2 Reinforcing the Cabinet by Method 1 5 5.2.3 Reinforcing the Cabinet by Method 2 8 5.2.4 Reinforcing the Cabinet by Method 3 10 5.2.5 Reinforcing the Cabinet by Method 4 12 5.3 Checking the Installation 14 Issue 05 (2006-11-20) Huawei Technologies Proprietary i Figures Position of joint plates 2 Combining the adjacent cabinets 3 Installation mode 4 Reinforcing the cabinet by method 1 6 Expected result 7 Reinforcing the cabinet by method 2 9 Expected result 10 Reinforcing the Cabinet by Method 3 11 Expected result 12 Reinforcing the cabinet by method 4 13 Expected result 14 T2-0416xx- 20050330-C- 1.20 Huawei Technologies Proprietary iii 5 Reinforcing the Cabinet About This Chapter This chapter guides you to reinforce the installed cabinets. For stability purpose, cabinets must be reinforced by the following methods.  Combining the adjacent cabinets with joint plates.  Reinforcing the cabinet to the cabling frame. The following table lists the contents of this chapter. Section Description 5.1Combining the Adjacent Cabinets Describes operations and procedures of combining the adjacent cabinets. 5.2Reinforcing the Cabinet to the Cabling Frame Describes operations and procedures of installing the cabinet shockproof components. 5.3Checking the Installation Describes the checklist of the installation. T2-0416xx- 20050330-C- 1.20 Huawei Technologies Proprietary 1 5 Reinforcing the Cabinet OptiX OSN 3500 Installation Manual 5.1 Combining the Adjacent Cabinets Purpose This procedure guides you to combine the adjacent cabinets with joint plates. Tools /Materials Joint plate Cross screwdriver Prerequisites The installation of cabinets is finished. Required/As needed As needed.  Note The adjacent cabinets must be combined with joint plates. Two joint plates are delivered with every cabinet. Step 1 Remove the joint plate from the top of the cabinet. Before delivery, the joint plates have been attached to the cabinet. See Figure 1.1. Joint plate Figure 1.1 Position of joint plates Step 2 Insert the M5 x 10 tapping screws into the joint plate and further into screw holes on the top of the two adjacent cabinets. Screw them tight to fix the joint plate. See Figure 1.1. 2 Huawei Technologies Proprietary Issue 05 (2006-11-20) OptiX OSN 3500 Installation Manual 5 Reinforcing the Cabinet Figure 1.1 Combining the adjacent cabinets End Issue 05 (2006-11-20) Huawei Technologies Proprietary 3 5 Reinforcing the Cabinet OptiX OSN 3500 Installation Manual 5.2 Reinforcing the Cabinet to the Cabling Frame This section guides you to reinforce a cabinet to the cabling frame. 5.2.1 Reinforcement Mode Select an installation mode according the following items:  Whether there are troughs at sides of the cabling frame.  The height the cabinet. Figure 1.1 shows the selection of installation mode. Start Any trough at cabling frame side? No 2600mm-high cabinet? 2600mm-high cabinet? Yes No End Yes No Yes Reinforcing a 2600mm-high cabinet (Method 1) Reinforcing a 2200mm-high or 2000mm-high cabinet (Method 2) Reinforcing a 2600mm-high cabinet (Method 3) Reinforcing a 2200mm-high or 2000mm-high cabinet (Method 4) Figure 1.1 Installation mode 4 Huawei Technologies Proprietary Issue 05 (2006-11-20) OptiX OSN 3500 Installation Manual 5 Reinforcing the Cabinet 5.2.2 Reinforcing the Cabinet by Method 1 Purpose This procedure guides you to reinforce the cabinets to the cabling frame. Tools /Materials Fixing bracket Insulation plate Diamond-shaped nut M8 x 20 bolt M8 x 25 bolt Prerequisites The cabinets have been installed already. The cabling frame has been installed. The cabinet is 2600 mm high. The cabling frame has side troughs. Required/As needed As needed. Step 1 Determine where to install the fixing part according to positions of the installed cabinet and the cabling frame. Step 2 Place the diamond-shaped nut into the trough of the cabling frame. Step 3 Place a spring washer and a flat washer onto the M8 x 20 bolt. Step 4 Insert the bolt assembly through the fixing bracket and screw the bolt into the diamond-shaped nut in the trough of the cabling frame. See Step 7Figure 1.1.  Note Do not screw the bolt too tight. Screw it until the bolt cannot fall out. Step 5 Place an insulation plate between the cabinet and the fixing bracket. Step 6 Place a spring washer, a big flat washer and an insulation washer onto the M8 x 25 bolt. Step 7 Insert the bolt assembly through the fixing bracket and insulation plate, and into the nut on the cabinet. See Figure 1.1. Issue 05 (2006-11-20) Huawei Technologies Proprietary 5 5 Reinforcing the Cabinet OptiX OSN 3500 Installation Manual  Note Do not screw the bolt too tight. Screw it until the bolt cannot fall out. 1 4 5 3 7 6 2 1.Cabinet 2. Cabling frame 3. Diamond-shaped nut 4. Fixing bracket 5. M8 x 20 bolt 6. M8 x 25 bolt 7. Insulation plate Figure 1.1 Reinforcing the cabinet by method 1 Step 8 Install other fixing parts, and adjust their relative positions according to the on- site engineering situation. Then screw all bolts tight. See Figure 1.1. 6 Huawei Technologies Proprietary Issue 05 (2006-11-20) OptiX OSN 3500 Installation Manual 5 Reinforcing the Cabinet Figure 1.1 Expected result End Issue 05 (2006-11-20) Huawei Technologies Proprietary 7 5 Reinforcing the Cabinet OptiX OSN 3500 Installation Manual 5.2.3 Reinforcing the Cabinet by Method 2 Purpose This procedure guides you to reinforce the cabinets to the cabling frame. Tools /Materials Fixing bracket Insulation plate Diamond-shaped nut M8 x 20 bolt M8 x 25 bolt Prerequisites The cabinets have been installed already. The cabling frame has been installed. The cabinet is 2200mm or 2000mm high. The cabling frame has side troughs. Required/As needed As needed Step 1 Determine where to install the fixing part according to positions of the installed cabinet and the cabling frame. Step 2 Adjust the height of the adjustable bracket according to the distance between the cabinet and the cabling frame. Step 3 Place the diamond-shaped nut into the determined position in the trough of the cabling frame. Step 4 Place a spring washer and a flat washer onto the M8 x 20 bolt. Step 5 Insert the bolt assembly through the adjustable bracket, and into the diamond- shaped nut in the trough of the cabling frame. Step 6 Insert another M8 x 20 bolt assembly through the fixing bracket and the adjustable plate, and into the corresponding nut with moderate force.  Note Do not screw the bolt too tight. Screw it until the bolt cannot fall out. Step 7 Place an insulation plate between the cabinet and the fixing bracket. See Figure 1.1. 8 Huawei Technologies Proprietary Issue 05 (2006-11-20) [...]... Manual 5 Reinforcing the Cabinet Figure 1.1 Expected result End 5.2.4 Reinforcing the Cabinet by Method 3 Purpose This procedure guides you to reinforce the cabinets to the cabling frame Tools /Materials Fixing bracket Insulation plate M8 x 50 bolt M8 x 25 bolt Clamp Prerequisites The cabinets have been installed already The cabling frame has been installed The cabinet is 2600 mm high The cabling frame... where to install the fixing part according to positions of the installed cabinet and the cabling frame Step 2 Adjust the height of the adjustable bracket according to the distance between the cabinet and the cabling frame 12 Huawei Technologies Proprietary Issue 05 (2006-11-20) OptiX OSN 3500 Installation Manual 5 Reinforcing the Cabinet Step 3 Place a spring washer and a flat washer onto the M8 ×50 bolt... plate between the cabinet and the fixing bracket Step 5 Place a spring washer, a big flat washer and an insulation washer onto the M8 x 25 bolt Step 6 Insert the bolt assembly through the fixing bracket and the insulation plate, and into the nut on the cabinet with moderate force See Step 7Figure 1.1  Note Do not screw the bolt too tight Screw it until the bolt cannot fall out Step 7 Install other fixing... 1.2 Expected result End 5.2.5 Reinforcing the Cabinet by Method 4 Purpose This procedure guides you to reinforce the cabinets to the cabling frame Tools /Materials Fixing bracket Insulation plate M8 x 50 bolt M8 x 20 bolt M8 x 25 bolt Clamp Prerequisites The cabinets have been installed already The cabling frame has been installed The cabinet is 2200mm or 2000mm high The cabling frame has no side troughs... Step 1 Determine where to install the fixing part according to positions of the installed cabinet and the cabling frame Step 2 Place a spring washer and a flat washer onto the M8 x 50 bolt 10 Huawei Technologies Proprietary Issue 05 (2006-11-20) OptiX OSN 3500 Installation Manual 5 Reinforcing the Cabinet Step 3 Insert the bolt assembly through the fixing bracket and the clamp, and screw it with moderate... Installation Manual 5 Reinforcing the Cabinet 4 5 3 6 5 2 1 7 8 1 .Cabinet 5 M8 × 20 bolt 2 Cabling frame 6 Fixing bracket 3 Diamond-shaped nut 7 M8 × 25 bolt 4 Adjustable bracket 8 Insulation plate Figure 1.1 Reinforcing the cabinet by method 2 Step 8 Place a spring washer, a big flat washer and an insulation washer onto the M8 x 25 bolt Step 9 Insert the bolt assembly through the fixing bracket and the insulation... assembly through the fixing bracket and the insulation plate, and into the nut on the cabinet with moderate force See Figure 1.1  Note Do not screw the bolt too tight Screw it until the bolt cannot fall out 5 3 4 6 7 2 1 8 9 1 .Cabinet 5 Adjustable bracket 2 Cabling frame 6 Fixing bracket 3 Clamp 7 M8 x 20 4 M8 × 50 bolt 8 M8 × 25 bolt 9 Insulation plate Figure 1.1 Reinforcing the cabinet by method... Step 8 Install other fixing parts, and adjust their relative positions according to the on- site engineering situation Then screw all bolts tight See Figure 1.1 Issue 05 (2006-11-20) Huawei Technologies Proprietary 13 OptiX OSN 3500 Installation Manual 5 Reinforcing the Cabinet Figure 1.1 Expected result End 5.3 Checking the Installation The following requirements should be met when the cabinet is reinforced... into the nut on the cabinet with moderate force See Step 7Figure 1.1  Note Do not screw the bolt too tight Screw it until the bolt cannot fall out Step 10 Install other fixing parts, and adjust their relative positions according to the on- site engineering situation Then screw all bolts tight See Figure 1.1 Issue 05 (2006-11-20) Huawei Technologies Proprietary 9 OptiX OSN 3500 Installation Manual 5 Reinforcing. .. adjust their relative positions according to the on- site engineering situation Then screw all bolts tight See Figure 1.2 5 3 4 2 1 6 7 1 .Cabinet 5 Fixing bracket 2 Cabling frame 6 M8 × 25 bolt 3 Clamp 7 Insulation plate 4 M8 × 50 bolt Figure 1.1 Reinforcing the Cabinet by Method 3 Issue 05 (2006-11-20) Huawei Technologies Proprietary 11 OptiX OSN 3500 Installation Manual 5 Reinforcing the Cabinet . Reinforcing the Cabinet by Method 1 5 5.2.3 Reinforcing the Cabinet by Method 2 8 5.2.4 Reinforcing the Cabinet by Method 3 10 5.2.5 Reinforcing the Cabinet. Contents Contents 5 Reinforcing the Cabinet 1 5.1 Combining the Adjacent Cabinets 2 5.2 Reinforcing the Cabinet to the Cabling Frame 4 5.2.1 Reinforcement Mode 4 5.2.2 Reinforcing