Laser engineering

Laser engineering

Journal of Lasers in Engineering, vol.6, pp. 161-187, 1997 1 LASER CLADDING PROCESS AND IMAGE PROCESSING F. MERIAUDEAU* F. TRUCHETET* D. GREVEY** and A.B. VANNES *** * Laboratoire GERE - Université de Bourgogne- 12 rue de la Fonderie- 71200 Le Creusot - France. Tel : (33) 85-80-30-30, Fax : (33) 85-80-36-15, email: F.Meriaudeau@gere.u-bourgogne.fr ** Laboratoire ThemoMécanique - Université de Bourgogne- 12 rue de la Fonderie- 71200 Le Creusot - France. Tel : (33) 85-80-30-30, Fax : (33) 85-80-36-15 *** CALFETMAT, MMP, Ecole Centrale de Lyon, BP 131, 69131 Ecully, France ABSTRACT The laser cladding process involves many processing parameters. We present in this paper a low cost system based on two CCD cameras, a standard acquisition card and a Personal Computer which enables the operator to interact with the process and processing parameters. Geometrical information can be extracted such as the height or the width of the track. Moreover, one of the camera is used to carry out temperature measurements. In addition we present three different methods of measuring the speed of the particles in the powder spray. INTRODUCTION The laser cladding process, which consists in adding a melted powder to a substrate in order to improve or change the behaviour of the material against one or several surface agressions, involves a lot of parameters. In order to perform good deposition some parameters need to be controlled during the process. In the first part we will see how the operating parameters influence the shape of the tracks. We will give a short summary of what one can find in the literature and we will also present the results obtained with our experimental set-up. CCD cameras have already been used to obtain information during processes such as laser welding, laser cladding or drilling. We shall show that a very cheap system based on a standard frame grabber,two CCD cameras and a Personal Computer can be used to provide the operator with important information during the laser cladding process. In the second part of the paper, we show that one camera previously calibrated with a black body enables the surface temperature to be determined. Moreover, the surface temperature can be used, using Beer Lambert’s law, to detect variations in the powder mass feed rate. With such a system it is possible to detect a fluctuation of 2 to 3g/min in the mass flow rate. The other camera provides information related to the powder distribution. A simple algorithm applied to the data acquired from the CCD matrix camera enables very weak fluctuations within both gas flows (carrier or shroud gas) to be observed. Journal of Lasers in Engineering, vol.6, pp. 161-187, 1997 2 As described in part four, this camera is also used to carry out geometrical measurements during the process. Geometrical parameters such as the height (build up), the width as well as the Half Height Width of the track are obtained in real time and enable the operator to obtain information related to the process parameters such as the speed of processing or the mass flow rate. As is known the speed of the particles is also a very important parameter. Indeed, this determines the irradiation time of the particles before reaching the surface, thus leading to different states of the powder, such as liquid or solid. If the particles are still solid, the irradiation time determines whether or not the particles have a uniform. In this part a special emphasis is placed on speed measurement. Indeed three different methods involving CCD cameras are presented measuring the speed of the particles. The accuracy of the different methods and the computation time required by those methods is discussed. In the last section the work is summarized and future developments discussed. IMPORTANT PARAMETERS In many industrial applications, the surface is the determining factor in the life time of the component. In such cases, it is important to be able to improve the surface properties [1] to [4]. One of the many known solutions [5] to [8], is to deposit a specific alloy which has the requisite properties. This is termed cladding. The main problem with this technique is the number of parameters and their influence on thequality of the clad tracks. Many investigations have been devoted to establish which parameters need to be controlled during the process in order to improve the quality of the track. We cite here some articles, [9] to [12], from an exhaustive literature. It can be stated that the main parameters are the speed processing, the powder feed rate , the laser power and the beam diameter. Depending on the configuration adopted: predeposed powder, coaxially blown powder, laterally blown, the parameters do not have the same effect. Moreover, if for example a coaxially blown powder system is used, one must control the carrier gas flow and the shroud gas flow. Small variations in the powder flow rate result in large fluctuations in the geometry and the microstructure of the tracks produced. At slower processing speeds (see figure 3), the surface reaches a higher temperature, leading to a deeper penetration and thus a higher dilution and lower specific properties. Judicious combination of the treatment parameters such as the laser power, the beam diameter, the processing speed and the powder feed rate enables the operator to control the process in order to obtain a dense cladding with a good metallurgical bond to the substrate. Variations in the parameters both lead to variations in the general shape of the tracks [13], [14], and also in the microstructure [15], [16]. Journal of Lasers in Engineering, vol.6, pp. 161-187, 1997 3 0 0,5 1 1,5 2 2,5 3 0 200 400 600 800 1000 1200 1400 Output Power (w) surface (mm2) figure 1: Variation of track section plotted against output power of the Nd:YAG laser 0 0,5 1 1,5 2 2,5 3 3,5 4 4,5 5 0 5 10 15 20 25 30 35 mass flow rate (g/min) surface (mm2) figure 2: Variation of track section plotted against powder flow rate 0 0,5 1 1,5 2 2,5 3 3,5 4 4,5 5 0 0,5 1 1,5 2 2,5 3 3,5 4 4,5 5 processing speed (mm/s) section (mm2) figure 3: Variation of track section plotted against processing speed Journal of Lasers in Engineering, vol.6, pp. 161-187, 1997 4 In order to reduce fluctuations and improve the reliabilty of the product, many researchers have trying to find good and reliable sensors. During the last few years many sensors have been tried but, the high cost of such equipment, the lack of real time or on line control has led manufacturies to seek other solutions. Some information in the literature shows how to control the laser power using an integrating sphere [9]. The powder feed rate can be controlled during the process using various methods: Grunenwalds and al [17] proposed a powder delivery system characterized by high flexibility and accuracy, Steen [18], [19], [20] and others [21], [22] used optical methods. High speed CCD camera are sometimes used and spectroscopy are required in the case of a plasma creation. Thus ways have been developed in order to control the mass feed rate, surface temperature, laser power and other pertinent parameters, involved in the laser cladding process over the past few years. However the price of this kind of sensors is still too high. We shall see below that the use of two CCD matrix cameras and some image processing tools is sufficient to detect variations of the main parameters. TEMPERATURE MEASUREMENTS In 1901 Max Planck developed an equation which describes a relationship between the intensity of electromagnetic radiation and its wavelength for any surface temperature. Planck's equation forms the basis for works done the field of radiometry. Max Planck's equation describes a continuum of radiation wavelengths (Fig. 4). Due to the temperature range in laser cladding our region of interest lies between 0.7 and 15 µm, the part of the electromagnetic spectrum in which most radiometric surface temperature measurements are made. 0.1 1 10 100 1000 10000 100000 1000000 0 1 2 3 4 5 6 7 8 9 10 11 12 13 Wavelength (µ µµ µm) Spectric energetic radiance (W/m 2 /sr/ µ µ µ µ m) T=3000K T=1800K T=1200K T=800K T=500K T=300K Figure 4: Graphical representation of Planck’s law Journal of Lasers in Engineering, vol.6, pp. 161-187, 1997 5 As we have shown earlier in references [24], [25], the surface temperature is a very important parameter which needs to be controlled. In order to provide contactless temperature measurement various radiometers can be used [26], but the use of a CCD camera enables the operator to get an average temperature as does a radiometer but it also provides temperature information for some precise areas. The calibration of the temperature measurement system was described in our references [28], [27]. The principle is to use the luminance emitted by the component and applying Planck’s law to be able to calculate the temperature[29], [30]. Since we do not require absolute measurements, errors made on the emissivity do not detract the efficiency of our system [31]. During cladding the camera scans the melt pool and provides an indication of the temperature. The surface temperature shows if a temperature high enough in order to melt all the particles has been reached. This is very important when different powders with different fusion temperatures are mixed since unmelted particles can initiate cracks in the clad leading to poor mechanical properties. Real time surface temperature measurements are performed using a simple algorithm based on the stastitical momentum conservation [32] (Wen’s algorithm) which detects the two gaussians (cold and hot area) provided by the histogram(see figure 5). [ ] M N f x y l l ji = ∑∑ 1 ( , ) (1) M l is the momentum of order l, N the number of pixels, and f(x,y) the grey level intensity of the pixel based on x=i and y=j. If P i is the proportion of pixels with the grey level intensity i (P i =n i /N), one can write the four first momentums of the image: M 0 =1 (2) M P i i i i 1 0 255 = = = ∑ * (3) M P i i i i 2 2 0 255 = = = ∑ * (4) M P i i i i 3 0 255 3 = = = ∑ * (5) A binarized image has only two populations Z 1 and Z 2 . If one notes q 1 (respectively q 2 ) the pixel proportion of grey level Z 1 (respectively Z 2 ); if one looks at the statistical momentum conservation; the system which needs to be solved is: M q z q z M q z q z M q z q z M q z q z 0 1 1 0 2 2 0 1 1 1 1 2 2 1 2 1 1 2 2 2 2 3 1 1 3 2 2 3 = + = + = + = + (6) After having found the linear system from the above non linear equations (6). The new system which has to be solved can be written: Journal of Lasers in Engineering, vol.6, pp. 161-187, 1997 6 M C M C M M C M C M 0 0 1 1 2 1 0 2 1 3 + = − + = − (7) C 0 and C 1 being known, one can evaluate the solutions Z 1 and Z 2 from the following equation Z C Z C 2 1 0 0+ + = (8) When Z 1 and Z 2 are found, it is very simple to calculate q 1 and q 2 from the two first equations of the system 6. Thus knowing q 1 and q 2 , Wen’s threshold is obtained when the repartition function is equal to q 1 . As soon as wen’s threshold has been figured out, the average grey level (corresponding to the temperature due to the linear relation of the temperature and the grey level in our system [26], [27]) is provided by the usual relation: G G Nb Nb i i i Wen threshold i i Wen threshold = = = ∑ ∑ * ' ' 255 255 (9) where: G i is the grey level i Nb i is the number of pixels having level value i 0 500 1000 1500 2000 2500 3000 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 210 220 230 240 250 Grey level intensity Number of Pixels Histogram of the image Wien's Threshold Figure 5. Temperature histogram As said before, the melt pool temperature is very important, because it tells to the operator if the melting temperature of all powder components has been reached. Moreover due to the fact that our CCD camera is placed at 45° (see figure 9) above the scene we are also able to detect variations in the processing parameters. Indeed, an increase in the mass feed rate lead to a decrease in the transmitted energy. In addition to this the track has a higher build up, thus a weaker area orientated to the camera. Journal of Lasers in Engineering, vol.6, pp. 161-187, 1997 7 As one can see on the graphics displayed below our system enables us to detect very weak variations in the mass flow rate (2 to 3 g/min (see figure 6). The authors would like to say here, that the results presented on the temperatures require an average on 3 images (120ms) This is due to the movements within the melt pool and the presence of bursting bubbles (see figures 7 and 8) during the process which lead to wide temperature variations. Thus in order to make some good comparisons, it is required to average over 3 images to smooth the temperature variations due to the different movements. 100 110 120 130 140 150 160 170 180 190 200 7 9 11 13 15 17 19 21 mass feed rate (g/min) grey level intensity Figure 6: Variation of the grey level intensity (temperature) versus the mass feed rate. Figures 7 and 8: visualisation of the melt pool.The lap between the two images is 40 ms. One can easily see the temperature difference due to pool movements and bursting bubbles. Bursting bubbles Journal of Lasers in Engineering, vol.6, pp. 161-187, 1997 8 figure 9: Set up of the experiment POWDER SUPPLY We use another CCD camera in order to check other different parameters. Using a coaxial delivery system [8], [10] we have to cope with variations occuring in the carrier gas flow or with the shroud gas flow. Once one has set an adequat carrier gas flow, fluctuations in the shroud gas flow induce large variations in the powder spray geometry and modify strongly the process results. In order to help the operator to set up correctly the shroud gas flow, we developed a short acquisition system. For this, we take some acquisition of the powder spray geometry using a CCD camera which is placed in front of the cladding nozzle. Experimentally, the substrate is located at 18 mm underneath the nozzle to insure a good quality coating [8]. On the acquired images, we realize an average in order to remove some points which are not reprensative of the distribution (this is done in order to perform this task automaticaly).The averaged image of the cross section is thresheld so that the width of the powder spray can be measured automatically. Some of the results obtained are displayed on the figure 12, as one can see the technics enable us to get very accurate information relative in this case to the shroud gas flow. temperature measurements Shape measurements (grazing angle) 45 ° Journal of Lasers in Engineering, vol.6, pp. 161-187, 1997 9 0 50 100 150 200 250 0 50 100 150 200 250 300 350 length (pixels) grey Level Intensity Figure 10: Transversal cross section of the powder beam of a single image 0 20 40 60 80 100 120 140 160 180 0 50 100 150 200 250 300 length (pixels) grey level intensity Figure 11: Transversal cross section of an average of three images 0 50 100 150 200 250 300 350 400 450 500 2 3 4 5 6 7 8 9 10 gaz flow rate (l/min) width of the powder beam(pixels) Figure 12: Variations of the width powder beam versus the shroud gas flow the correct value corresponds to image 2 Not representative and very hard to do not to take into account in an automatic processing threshold width of the powder spray 1 2 3 Journal of Lasers in Engineering, vol.6, pp. 161-187, 1997 10 SHAPE MEASUREMENTS CCD cameras have found many applications in the field of measuring the geometrical characteristics of an object, and reveal sometimes paramount information which are not accessible by another meaning. Indeed, as we have shown through the aforedisplayed curves 1 to 3, we have a changement in the track section when variations in the parameters occur. Moreover, in order to be more accurate we display below on the figure 13 the variations of the height of the tracks versus the variations of the important parameters such as the processing speed. In order to control these parameters during the process, the CCD camera is placed at a grazing angle. Thus the camera can see the formation of the tracks in real time. Using these acquisitions we are able to detect variations of the height and of the width of the track. Those parameters are provided by the use of an edge detector [34] (Roberts) and an algorithm which is able to find the width of the tracks (the wider part) and knowing the width one can find the height. The algorithm can also easily measures the Half Height Width (figure 14-15) as well as the cross section of the track and consequently we determine the process efficiency. As shown on the results (see figure 11) the system is able to detect very small in the processing speed. 0 0,2 0,4 0,6 0,8 1 1,2 1,4 1,6 0 0,02 0,04 0,06 0,08 0,1 0,12 0,14 0,16 0,18 0,2 processing speed (m/min) Height (mm) Série1 Série2 Série3 Série4 Results found by postmortem metallurgical analysis Found by image processing Figure 13. Variation track height provided by the CCD camera versus the processing speed [...]... Journal of Lasers in Engineering, vol.6, pp 161-187, 1997 REFERENCES [1] M JEANDIN « Traitements par laser et faisceaux d’électrons » Technique de l’ingénieur, Matériaux et techniques, pp15-22, Dec 89 [2] P G MOORE, L S WEINMAN, « Surface alloying using high-power continuous laser » SPIE, Laser Applications in Materials Processing, San Diego, pp 120-125, 1979 [3] CONFERENCES, « Surface engineering: ... prospects » Surface Engineering, Vol 7, N°2, pp 109-115, 1991 [4] W M; STEEN, « Laser Surface Finishing » Trans IMF, Vol 67, pp 124-126, 1989 [5] W M STEEN, "Adaptative control of laser material processing" LAMP'92, NAGOAKA, pp 439-444, Jun 92 [6] W M STEEN, "Laser surface claddidng" Laser surface treatment of metal,Nato ASI, pp 369-388, 1986 [7] T TAKEDA, K ADACHI, H HISADA, "Laser alloying of aluminium... WEERASINGHE, P MONSON, "Some aspects of the formation of laser clad tracks" SPIE, High power laser and their industrial application, Vol 650, pp 226-234, Apr 1986 [13] Z XIAOYAN, T ZENGYI, Z BEIDI, C KUN, "Parameters investigation of laser cladding coating auto-feeding apparatus" LAMP'92, NAGOAKA, pp 831-836, Jun 92 [14] P.-A VETTER, Th ENGEL, J FONTAINE, "Laser cladding: the relevant parameters for process...Journal of Lasers in Engineering, vol.6, pp 161-187, 1997 width height figures 14 and 15: image acquired at a grazing angle Results after application of an edge detector Due to the fact that an ambiguity may exist on which parameter varies, we add another sensor to check the mass feed rate The sensor is an optical sensor (photovoltaïc cell) to which a laser beam going through the... interesting part of the stream 13 Journal of Lasers in Engineering, vol.6, pp 161-187, 1997 figure 18: trajectory and particle speed In order to investigate the speed of the particles both within the core of the powder distribution and with a reasonable mass feed rate, the authors used a CCD camera with a variable integration time (electronic shutter) and a laser light-sheet in order to inspect the powder... revêtements élaborés sous faisceau laser par projection de poudre sur substrat base aluminium: caractérisation microstructurale, mécanique et tribologique» Thèse de l’INSA, 1994 [11] J-D WAGNIERE, C F MARSDEN, A FRENK, M PICASSO, H J RUSTERHOLZ, "Cartes de procédé pour le recouvrement par laser CO2" Proc of the 5th international conference on welding and melting by electron and laser beams, pp 451-458, Jun... in order to hastily sample the image 19 Journal of Lasers in Engineering, vol.6, pp 161-187, 1997 CONCLUSION We presented through this article a low cost system using two CCD matrix cameras, a standard acquisition card and a Personnal Computer which enables the operator to get information about the process during the warm-up period and during the laser cladding process itself Some of these information... FRENK, « Recouvrement par laser: microstructure et comportement en frottement d’un alliage à base Cobalt » These N° 1101, Ecole Polytechnique Fedérale de Lausanne, 1993 [16] Y P KATTHURIA, A TSUBOI, « Laser cladding of Stellite: a detailed analysis » Europtio, SPIE, Besançon, May 96 [17] B GRUNENWALD, St NOWOTNY, W HENNIG, F DAUSIGER, H HUGEL, "New technological developments in laser cladding" ICALEO'93,... 89-100, 1990 [19] L LI, W.M.STEEN, N Qi, D.J BROOKFIELD, "On-line Laser Weld Sensing For Quality Control" ICALEO, pp 411-421, 1990 [20] L LI, W M STEEN, "Sensing, modelling and closed loop control of powder feeder for laser surface modification" ICALEO'93, pp 965-974, 1993 [21] J Y FENG, B QUAYLE, P.J MODERN, W M STEEN, "Computer control of laser multipowder feeder cladding system for optimal alloy scan... TRUCHETET «CCD technology applied to industrial welding applications» 21 Journal of Lasers in Engineering, vol.6, pp 161-187, 1997 MELECON_96, BARI, Italy,pp 1335-1338, May 1996 [25] F MERIAUDEAU, E RENIER, F TRUCHETET, « Temperature imaging and image processing in steel industry» Submitted for publication to Optical Engineering [26] E RENIER, F MERIAUDEAU, F TRUCHETET, H ANDRZEJEWSKI, P SUZEAU, " Near . Journal of Lasers in Engineering, vol.6, pp. 161-187, 1997 1 LASER CLADDING PROCESS AND IMAGE PROCESSING F. MERIAUDEAU*. have already been used to obtain information during processes such as laser welding, laser cladding or drilling. We shall show that a very cheap system based