SINUMERIK 802D Brief Instructions Milling User Documentation 11.2000 Edition SINUMERIK 802D Milling Valid for Control SINUMERIK 802D 11.2000 Edition Software version SINUMERIK® documentation Printing history Brief details of this edition and previous editions are listed below The status of each edition is shown by the code in the "Remarks" column Status code in the "Remarks" column: A B C New documentation Unrevised reprint with new Order No Revised edition with new status Edition Order No Remark 11.00 6FC5298-1AA40-0BP0 A This manual is included in the documentation on CD-ROM (DOCONCD) Edition Order No Remark 08.01 6FC5298-6CA00-0BG1 C Trademarks ® ® ® ® SIMATIC , SIMATIC HMI , SIMATIC NET , SIROTEC , ® ® SINUMERIK and SIMODRIVE are registered trademarks of Siemens AG Other names in this publication might be trademarks, whose use by a third party for his own purposes may violate the rights of the registered holder Further information is available on the Internet under: http://www.ad.siemens.de/sinumerik This publication was produced with WinWord V 7.0 and Designer V 8.0 Other functions not described in this documentation might be executable in the control This does not, however, represent an obligation to supply such functions with a new control or when servicing Subject to technical change without prior notice The reproduction, transmission or use of this document or its contents is not permitted without express written authority Offenders will be liable for damages All rights, including rights created by patent grant or registration of a utility model or design are reserved © Siemens AG 2000 All Rights Reserved General Information 11.00 Introduction How to use this booklet This manual is a brief instruction manual which describes all of the important operator control and programming steps Detailed description of the operator control and programming for Sinumerik 802D: • User Manual, Turning, Order No 6FC5698-2AA00-0BP0 • User Manual, Milling Order No 6FC5698-2AA10-0BP0 Description schematic This description is structured as follows: Operator control Prerequisites Operating sequence Programming Programming of the function Meaning of the parameters Explanatory illustration with an example of a workpiece Siemens AG 2000 All rights reserved SINUMERIK 802D Brief Instructions Milling (BNKF) - 11.00 Edition 0-5 List of sections 11.00 List of sections Setting-Up 1-9 Tool offsets and compensation .1-10 Measure tool 1-11 Determine workpiece zero 1-12 Enter the zero offset 1-13 Generate/Edit Program 2-15 Set-up/open program 2-16 Insert/edit block .2-17 Copy/insert/delete block 2-18 Search/number the block 2-19 Start/simulate program 2-20 Commission/Correct Program 3-23 Select program .3-24 Correct program 3-25 Block search 3-26 Trace machining on the screen 3-27 Program Path Data 4-29 Absolute and incremental dimensions, G90, G91 4-30 Zero offset, G54 to G59 4-31 Selection of working plane G17 to G19 4-32 Programming Axis Motion 5-33 Rapid traverse, G0 5-34 Linear interpolation, G1 5-35 Circular interpolation, G2/G3 5-36 Circular interpolation through intermediate point, CIP 5-38 Rigid tapping, G331/G332 5-39 Tapping with floating tap holder, G63 .5-40 Polar coordinates G110, G111, G112 5-41 Tool Offsets and Compensation 6-43 Tool call 6-44 Cutter radius path compensation, G41/G42 6-45 Tool nose radius compensation, G41/G42 .6-46 Approach/exit contour, NORM/KONT .6-47 Move along the contour, G450/G451 6-48 0-6 Siemens AG 2000 All rights reserved SINUMERIK 802D Brief Instructions Milling (BNKF) - 11.00 Edition 11.00 List of sections List of sections Coordinate Systems 7-49 Frame concept 7-50 Shift/rotate coordinates, TRANS/ROT 7-51 Mirroring the coordinate axes, MIRROR 7-52 Increasing/reducing size of contour, SCALE 7-53 Programming Preparatory Functions 8-55 Exact stop, G9/G60 .8-56 Feed in continuous path mode, G64 .8-57 Programming the spindle motion 8-58 Subroutine technique 8-59 Attachment 9-61 List of M commands 9-62 List of G functions 9-63 Notes 9-68 Siemens AG 2000 All rights reserved SINUMERIK 802D Brief Instructions Milling (BNKF) - 11.00 Edition 0-7 0-8 ♥ Siemens AG 2000 All rights reserved SINUMERIK 802D Brief Instructions Milling (BNKF) - 11.00 Edition Setting-Up Tool offsets and compensation 1-10 Measure tool 1-11 Determine workpiece zero 1-12 Enter the zero offset 1-13 Siemens AG 2000 All rights reserved SINUMERIK 802D Brief Instructions Milling (BNKF) - 11.00 Edition 1-9 Setting-Up 11.00 Tool offsets and compensation Prerequisite: JOG mode selected Selection OFFSET PARAM Tool list Select OFFSET PARAM operating area Select "Tool list" menu Functions Measure tool Determine the tool offset data Delete tool Delete the tool offsets Expanded Display all of the tool parameters Cut Set-up additional cuts Search Search for tool New tool Set-up new tool Enter the new values 1-10 Siemens AG 2000 All rights reserved SINUMERIK 802D Brief Instructions Milling (BNKF) - 11.00 Edition ... SINUMERIK 802D Milling Valid for Control SINUMERIK 802D 11.2000 Edition Software version SINUMERIK? ? documentation Printing history Brief details of this edition and previous editions... rights reserved SINUMERIK 802D Brief Instructions Milling (BNKF) - 11.00 Edition 0-7 0-8 ♥ Siemens AG 2000 All rights reserved SINUMERIK 802D Brief Instructions Milling (BNKF) - 11.00 Edition 1 Setting-Up... reserved SINUMERIK 802D Brief Instructions Milling (BNKF) - 11.00 Edition 1-13 Setting-Up 1-14 11.00 Siemens AG 2000 All rights reserved SINUMERIK 802D Brief Instructions Milling (BNKF) - 11.00 Edition