Tài liệu KRONE - TrueNet Performance requirements ppt

Section TrueNet™ Structured Cabling Systems TrueNet™ Cabling n The TrueNet Structured Cabling System is the industry’s most revolutionary local area network (LAN) technology—precisely because it is the only system that moves beyond traditional adherance to TIA/EIA industry standards to what is really important to the end-user…data throughput n The TrueNet Cabling System is the only system specifically designed to prevent bandwidth loss in LANs n TrueNet Structured Cabling Systems consist of an integrated system of horizontal cable, patch cords, terminal blocks, jacks and patch panels— all precisely tuned to protect the efficiency of the network n The TrueNet Warranty certifies zero bit error data transmissions in the physical layer by performing active testing on all installed systems at the end-users’ locations n TrueNet Systems are available for proposed Category (C6T™) and Category 5e (C5eT™) requirements KRONE Product Catalog MK005-01.I07 http://www.kroneamericas.com 2-1 TrueNet™ Structured Cabling Systems TrueNet™ Cabling A New Concept in Network Technology A System Breakthrough That Allows Maximum Network Throughput Impedance Mismatched Channel TrueNet Structured Cabling Systems are a truly revolutionary new concept in network technology A TrueNet System provides far more than proposed Category 6, 5e or compliance — it actually helps users get the most out of their active equipment, the bandwidth they paid for The System is an integrated, precisely tuned system of horizontal cable, patch cords, jacks, terminal blocks and patch panels — everything from NIC to server The result is the industry’s only impedance-matched system that provides a clear path for uninterrupted data throughput TrueNet Impedance Matched Channel And the KRONE TrueNet System guarantees zero bit error data transmission — a promise fully backed by a single-source, enduser warranty No one else in the industry matches this level of performance…or assurance…of network efficiency New Tests Reveal Key Determinants of Network Performance Today, there’s a new generation of testing equipment that looks at the entire network while it’s under operation These “active” tests show that the degree to which all network components are impedance matched has a great effect on the throughput of the network In addition, they reveal that many, if not most, of today’s high-speed networks are operating well below peak performance KRONE research with active network test equipment confirms that mixing and matching components that individually meet TIA/EIA standards does not ensure efficient network performance Optimal network throughput can only be achieved with components that are 100±3 ohms impedance matched The charts shown (above, right) demonstrate the impedance match/mismatch phenomenon The mismatched channel illustration depicts what can happen when a 107 ohm patch cord is connected to a 97 ohm horizontal cable Typically, energy is reflected at the connection point, causing signal degradation, data errors and data retransmissions These occurrences can have a serious impact on network performance Impedance-matched components allow your data to travel throughout the network with minimal reflection and loss Maximum Percent of Retransmissions 0% 1% 2% 3% 4% 5% Data Capacity Ethernet LAN Worth (Based on $1 Million Equipment Investment) 100Mb/s 20Mb/s 4Mb/s 0.8Mb/s 0.16Mb/s 0.032Mb/s $1,000,000 $200,000 $40,000 $8,000 $1,600 $320 Effect of data retransmission on network throughput — 80% degradation from only 1% retransmission The TrueNet cabling system, depicted by the matched channel illustration, shows how matched 100±3 ohm components allow the signal to travel without reflection and loss Data retransmissions dramatically reduce the throughput of the network As shown in the table (right), even a 1% rate of retransmission can slow a 100Mb/s Ethernet network to just 20Mb/s — turning a $1 million network equipment investment into a $200,000 investment 2-2 http://www.kroneamericas.com KRONE Product Catalog MK005-01.I07 TrueNet™ Structured Cabling Systems A New Concept in Network Technology TrueNet™ Cabling Factors Affecting Network Throughput Electrical characteristics such as impedance, ACR, and delay skew are important However, the true test of any structured wiring plan is how well the original data is retained as it travels within the physical layer Common inconsistencies in structured cabling, such as impedance mismatches, cause data errors This impedance mismatch causes instability across the frequency spectrum How the TrueNet System Protects Network Throughput KRONE has solved network retransmission problems by designing a structured cabling system to impedance-matching standards that are more rigorous than the current standards, and which include IEEE system guidelines not found in the traditional TIA/EIA structured cabling standards These TrueNet C6T™ and C5eT™ solutions incorporate tuned components, including patch cables, jacks, termination blocks, horizontal cables and termination hardware TrueNet’s total system tuning protects data integrity and enhances network throughput Tested On-Site and Backed by a Zero Bit Error* Warranty The TrueNet System is backed by an industry-leading warranty program that addresses what is really important to the network user: data throughput KRONE assures that each installed TrueNet Structured Cabling System achieves maximum throughput performance by conducting active network testing on-site No other warranty program offers this kind of peace-of-mind to the end-user Electrical instability can hurt data integrity This potentially causes data retransmission to occur, which, in turn, causes a reduction in Ethernet throughput TrueMatch™ — A Revolutionary Innovation in Technology TrueNet™ Cable is based on TrueMatch technology, a series of over 10 patented product design and manufacturing innovations that fine-tune the cable to various system components (such as connectors) to achieve a 100±3 ohms differential impedance throughout the cabling system The resulting system allows the signal to travel the physical layer cleanly, with fewer performance-robbing data retransmissions With the revolutionary TrueMatch process, each pair is manufactured separately — then individually sized and tuned with an identical, tight twist ratio and combined within the jacket TrueMatch cables are as close to perfect as is possible TrueMatch Assures that: n The copper conductors of each TrueNet cable have a near-perfect (99% round) circumference, plus a near-perfect distance variation (99–100%) within the insulation n The conductors and insulation diameters of each pair are individually fine-tuned to achieve the 100±3 ohms impedance requirements The“20/5” TrueNet Warranty, offered directly to the end-user, covers all aspects of the structured cabling system for horizontal and backbone networks that support data and voice, both copper and fiber, including patch cords, horizontal cabling, jacks, and patch panels It’s the industry’s first throughput warranty that covers zero bit errors over the passive components of the network for a full five years, plus a separate 20-year electrical performance, application assurance and product warranty * Overall bit error rate guaranteed for a 5-year period not to exceed a limit of 10-12th (due to the structured cabling under warranty) KRONE Product Catalog MK005-01.I07 http://www.kroneamericas.com 2-3 TrueNet™ Cabling TruePatch™ Patch Cords A Simple, Effective Way to Boost Performance and Reliability Impedance vs Frequency As an integral part of the TrueNet™ Structured Cabling System, or when used individually, TruePatch Patch Cords provide a vital system upgrade and solve a problem found in many networks: a random selection of unmatched, low-performance/low-reliability patch cords New research shows that even one marginal patch cord can substantially slow down an entire network These same tests also show that overall network performance can be improved simply by replacing existing patch cords with high-performance, impedance-matched TruePatch Patch Cords (right) These tests show that impedance mismatches which occur at the transition between patch cords and jacks have a dramatic impact on network performance The figure on the top, right shows a randomly chosen horizontal cable with a randomly chosen patch cord The frequency curve shows wild oscillations But by just placing a TruePatch Patch Cord with the same horizontal, the impedance curve is much smoother (bottom, right) TruePatch Patch Cords utilize TrueMatch™ technology but they also feature some unique design innovations: n The copper conductors in TruePatch Patch Cords are stranded for superior flexibility, then compacted into a near-round shape to enhance the impedance values A dual layer insulation prevents the separation of the copper strands — even with repeated flexing Separate patents are The copper strands pending on these unique innovations are compacted, presenting a round n A high pressure, injection-molded boot locks each pair in place inside the conductor for increased impedance plug, resulting in an extra-strong performance A dual termination insulation layer prevents strand n An extra-long strain relief prevents separation kinking at the plug head, maintaining the required 1" bending radius Before TruePatch Impedance vs Frequency Same channel viewed after the installation of TruePatch To achieve maximum performance, however, all TruePatch Patch Cords are offered in lengths which are proven to minimize signal reflection (4, 7, 10 and 15 feet) 2-4 http://www.kroneamericas.com KRONE Product Catalog MK005-01.I07 TrueNet™ Structured Cabling Systems Channel Options TrueNet C6T delivers exceptional system performance by including features that protect signal integrity and strength The IEEE specifications for signal amplitude will be especially important for Gigabit Ethernet (which uses multilevel encoding) In addition, these features may also enable lower voltage NIC cards to transmit a clean signal (see below comparison of signal amplitude for a mismatched vs TrueNet System) TrueNet C6T takes TrueMatch™ technology even further It provides the tightest levels of impedance-matching available, and adds KRONE’s patent-pending star separator This helically-twisted separator improves pair-to-pair isolation and reduces pair-to-pair, powersum and alien (cable-to-cable) crosstalk for best performance in noisy networks like Gigabit Ethernet In addition, heavier 23-gauge copper is used for better signal strength The TrueNet C6T Solution delivers: n A complete end-to-end channel n Extra bandwidth, better attenuation n Zero bit errors n ISO/IEC 11801, Class E compliance n Proposed Category compliance C6T RJ45 Modular Solution TrueNet™ C6T Cable Hub/Switch Plug ’n’ Play Patch Panel with HighBand™ Jacks HighBand™ Jacks TruePatch™ C6T C6T IDC Block Solution HighBand™ Ultim8™ Blocks TrueNet™ C6T Cable Hub/Switch TruePatch™ C6T HighBand™ Jacks TruePatch™ C6T Mismatched Signal Amplitude TrueNet Signal Amplitude The mismatched channel allows signal amplitude to fall out of IEEE specifications The TrueNet channel preserves signal amplitude within IEEE specifications KRONE Product Catalog MK005-01.I07 TruePatch™ C6T TrueNet was designed in concert with the first generation of Gigabit Ethernet cards which will use complicated digital signal processing (DSP) chips for signal decoding TrueNet C6T takes Gigabit Ethernet one step further: signal transmission over TrueNet C6T is so good that the need for DSPs is reduced, allowing active equipment manufacturers to build nextgeneration, low-cost Gigabit Ethernet equipment without extra chips TrueNet™ Cabling C6T — For the Ultimate Gigabit Ethernet Network http://www.kroneamericas.com 2-5 TrueNet™ Structured Cabling Systems TrueNet™ Cabling Channel Options TrueNet C6T System Components Product HighBand™ RJ45 Keystone Jack UMS Mounting System Hi Density Keystone Patch Panel Patch Plus Patch Panel w/Cable Mgmt Plug ’n’ Play Patch Panel Plug ’n’ Play Patch Panel Ultim8™ Block Ultim8 Field Assembly Kit Ultim8 Field Assembly Kit TruePatch™ Patch Cords – Wired Straight Through TruePatch Patch Cords – Wired Straight Through TruePatch Patch Cords – Wired Straight Through TruePatch Patch Cords – Wired Straight Through TruePatch Patch Cords TruePatch Patch Cords TruePatch Patch Cords TruePatch Patch Cords TruePatch Patch Cords TruePatch Patch Cords TruePatch Patch Cords TruePatch Patch Cords Plenum Reels Non-plenum Reels Angled Faceplate Angled Faceplate Flush Mount Faceplate Flush Mount Faceplate Flush Mount Faceplate Flush Mount Faceplate Color Key For * substitute 01-white 02-ivory 03-gray 04-black 05-red 06-blue 07-green 08-yellow 09-purple 10-orange 2-6 For ** substitute 01-white 02-ivory 03-gray 04-black Description Part Number T568 A/B — 24-Port 24-Port 24-Port 48-Port 8-Pair 96-Pair 160-Pair 6645 6657 6450 6653 6653 6653 6468 6636 6636 Ultim8 Plug-to-Ultim8 Plug, feet TP6TH***04 3-4 Ultim8 Plug-to-Ultim8 Plug, feet TP6TH***07 3-4 Ultim8 Plug-to-Ultim8 Plug, 10 feet TP6TH***10 3-4 Ultim8 Plug-to-Ultim8 Plug, 15 feet Ultim8 Plug-to-RJ45, feet Ultim8 Plug-to-RJ45, feet Ultim8 Plug-to-RJ45, 10 feet Ultim8 Plug-to-RJ45, 15 feet RJ45-to-RJ45, feet RJ45-to-RJ45, feet RJ45-to-RJ45, 10 feet RJ45-to-RJ45, 15 feet 4-Pair, 23 AWG 4-Pair, 23 AWG 4-Port 8-Port 2-Port 4-Port 6-Port 12-Port, Dual Gang TP6TH***15 TP6TB***04 TP6TB***07 TP6TB***10 TP6TB***15 TP6TA***04 TP6TA***07 TP6TA***10 TP6TA***15 TN6TP**02 TN6TR**02 6644 174-** 6644 178-** 6644 152-** 6644 154-** 6644 156-** 6644 157-** 3-4 3-4 3-4 3-4 3-4 8-10 8-10 8-10 8-10 10-3 10-4 9-6 9-6 9-7 9-7 9-7 9-8 2 2 1 800-** 165-00 054-01 760-24 003-24 003-48 060-06 596-06 510-06 Catalog Pages 9-2 7-3 8-7 8-7 8-7 8-7 3-2 3-3 3-3 For *** substitute BL-blue GY-gray WT-white GN-green YL-yellow RD-red http://www.kroneamericas.com KRONE Product Catalog MK005-01.I07 TrueNet™ Structured Cabling Systems Channel Options TM The TrueNet C5eT Cabling System is KRONE’s entry level throughput enhanced solution This system fully meets the requirements of Category 5e, plus it adds throughput optimizing features of 100Base-T operation C5eT RJ45 Modular Solution TrueNet™ C5eT Cable Hub/Switch The proof of TrueNet C5eT System performance is in the test results The graphs (below) depict the rise time of both an impedance mismatched and matched (TrueNet) system The mismatched channel falls out of the IEEE spec; the TrueNet System keeps rise time within the IEEE specs, preserving signal integrity Plug ’n’ Play Patch Panel with K600 Jacks TruePatch™ C5eT K600 Jacks The TrueNet C5eT Solution delivers: n A complete end-to-end channel n Extra bandwidth, better attenuation n Zero bit errors (enhanced DSP electronics required for 1000Base-T) n TIA/EIA-568-A Category 5e compliance n ISO/IEC 11801, Class D compliance TrueNet™ Cabling The Throughput Optimized Category C5eT Network TruePatch™ C5eT TrueNet™ C5eT Cable Hub/Switch Enhanced Patch Panel TruePatch™ C5eT K600 Jacks TruePatch™ C5eT Mismatched Signal Rise Time C5eT IDC FT Block Solution TrueNet™ C5eT Cable Feed Thru (FT) Block Hub/Switch TruePatch™ C5eT K600 Jacks The mismatched channel’s corrupted signal causes rise time to fall out of IEEE specifications TruePatch™ C5eT TrueNet Signal Rise Time The TrueNet channel keeps rise time within specifications, preserving signal integrity KRONE Product Catalog MK005-01.I07 http://www.kroneamericas.com 2-7 TrueNet™ Structured Cabling Systems TM TrueNet™ Cabling Channel Options TrueNet C5eT System Components Product Description Enhanced Patch Panel, Cat 5e Enhanced Patch Panel, Cat 5e Enhanced Patch Panel, Cat 5e Enhanced Patch Panel, Cat 5e UMS/Mini Patch Panel UMS/Mini Patch Panel UMS/Mini Patch Panel UMS/Mini Patch Panel Kit UMS/Mini Patch Panel Kit UMS/Mini Patch Panel Kit UMS/Mini Patch Panel Kit K600 Jack 25-Pair FT (Feed-Thru) Block TruePatch™ Patch Cords TruePatch Patch Cords TruePatch Patch Cords TruePatch Patch Cords TruePatch Patch Cords TruePatch Patch Cords TruePatch Patch Cords TruePatch Patch Cords TruePatch Patch Cords TruePatch Patch Cords TruePatch Patch Cords TruePatch Patch Cords Plenum Reels Plenum Reelex PVC Reels PVC Reelex Angled Faceplate Angled Faceplate Flush Mount Faceplate Flush Mount Faceplate Flush Mount Faceplate Flush Mount Faceplate Color Key For * substitute 01-white 02-ivory 03-gray 04-black 05-red 06-blue 07-green 08-yellow 09-purple 10-orange 2-8 For ** substitute 01-white 02-ivory 03-gray 04-black 24-Port, (6) 4-Port Groups 48-Port, (12) 4-Port Groups 24-Port, (4) 6-Port Groups 48-Port, (8) 6-Port Groups 6-Port (105mm) 6-Port (160mm) 12-Port (160mm) 6-Port (105mm) w/Mtg Kit 12-Port (160mm) w/Mtg Kit 24-Port (160mm) w/Mtg Kit 48-Port (160mm) w/Mtg Kit RJ45 4-Pair color coded FT Plug-to-FT Plug, 4-Pair, feet FT Plug-to-FT Plug, feet FT Plug-to-FT Plug, 10 feet FT Plug-to-FT Plug, 15 feet FT Plug-to-RJ45, feet FT Plug-to-RJ45, feet FT Plug-to-RJ45, 10 feet FT Plug-to-RJ45, 15 feet RJ45-to-RJ45, feet RJ45-to-RJ45, feet RJ45-to-RJ45, 10 feet RJ45-to-RJ45, 15 feet 4-Pair, 24 AWG 4-Pair, 24 AWG 4-Pair, 24 AWG 4-Pair, 24 AWG 4-Port 8-Port 2-Port 4-Port 6-Port 12-Port, Dual Gang Part Number 6653 466-24 6653 466-48 6653 646-24 6653 646-48 6653 606-00 6653 606-02 6653 612-00 6653 806-00 6653 812-00 6653 824-00 6653 848-00 6467 081-* 6631 135-05 TP5ETF***04 TP5ETF***07 TP5ETF***10 TP5ETF***15 TP5ETB***04 TP5ETB***07 TP5ETB***10 TP5ETB***15 TP5ETA***04 TP5ETA***07 TP5ETA***10 TP5ETA***15 TN5ETP***02 TN5ETP***XXII TN5ETR***XX02 TN5ETR***XXII 6644 174-** 6644 178-** 6644 152-** 6644 154-** 6644 156-** 6644 157-** Catalog Pages 8-2 8-2 8-2 8-2 8-4 8-4 8-4 8-3 8-3 8-3 8-3 9-3 4-2 4-6 4-6 4-6 4-6 4-6 4-6 4-6 4-6 8-11 8-11 8-11 8-11 10-6 10-6 10-9 10-9 9-6 9-6 9-7 9-7 9-7 9-8 For *** substitute BL-blue GY-gray WT-white GN-green YL-yellow RD-red http://www.kroneamericas.com KRONE Product Catalog MK005-01.I07 TrueNet™ Performance Specifications Channel Specifications TrueNet™ Cabling TrueNet C6T/C5eT Channel Performance Specifications Individual cable component (passive electrical) specifications are found within Section 10, Bulk Copper Cable The following specifications relate to active channel situations using two C6T configuration scenarios: n HighBand™ Jack to HighBand Jack n Ultim8™ Termination Block to HighBand Jack Four C5eT configuration scenarios are also included: n Enhanced Patch Panel to K600 Jack n K600 Jack to K600 Jack n UMS/Mini Patch Panel to K600 Jack n 25-Pair FT (Feed-Thru) Block to K600 Jack In accordance with IEEE Input Specification Limits, active network specifications (100Base-T) for each configuration include: positive amplitude, negative amplitude, amplitude symmetry, rise time, fall time, rise time/fall time symmetry and jitter Passive electrical specifications relative to a 100-meter channel are also provided KRONE Product Catalog MK005-01.I07 http://www.kroneamericas.com 2-9 TrueNet™ Performance Requirements C6T Supported Applications: Active Network Specifications n IEEE Input Specification Limits/100Base-T n n 10/100/1000Base-T (IEEE 802.3xx) 4/16 Mbps Token Ring 25,155,622 Mbps ATM Spec Positive Amplitude: Negative Amplitude: Amplitude Symmetry: Rise Time: Fall Time: Rise Time/Fall Time Symmetry: Jitter: TrueNet™ Cabling HighBand™ Jack to HighBand Jack Min 0.95V 0.95V 0.98% ns ns ns 0% Max 1.05V 1.05V 1.02% ns ns 0.5 ns 1.4% 100-Meter Channel Passive Electrical Specifications Freq (MHz) Attenuation (dB) [min] 10 16 20 25 31.25 62.5 100 150 200 250 2.1 4.0 5.6 6.3 8.0 9.0 10.1 11.3 16.3 21.0 26.1 30.6 34.6 PowerSum NEXT (dB) PowerSum ACR (dB) [typical] [min] [typical] [min] [typical] [min] [typical] 1.6 3.6 5.1 5.8 7.4 8.3 9.3 10.5 15.3 19.7 24.7 29.1 33.1 70.3 60.6 55.6 54.0 51.0 49.0 47.4 45.7 40.6 37.1 34.0 31.9 30.2 82.1 72.4 67.5 65.9 62.6 61.0 59.4 57.9 53.0 49.7 46.8 44.8 43.2 68.2 56.6 50.0 47.7 42.6 40.0 37.3 34.4 24.3 16.2 8.0 1.3 -4.5 74.0 72.1 67.9 66.0 61.4 58.9 56.1 53.2 42.4 33.9 25.8 19.5 14.4 21 21 21 21 21 21 20 19 16 14 12 11 10 30 30 30 30 30 30 29 28 25 23 22 20 19 Characteristic Impedance For Cable: Channel Propagation Phase Delay: Channel Delay Skew: Ω) 100Ω Ω (±3Ω @ 100 MHz 548 ns 30 ns n n n 2-10 Return Loss (dB) http://www.kroneamericas.com Minimum values [min] represent the worst case allowable in a TrueNet™ system Minimum TrueNet values are derived from and meet or exceed proposed TIA/EIA Category values Typical values [typical] were obtained from passive testing over a 100-meter channel in a UL certified laboratory under controlled conditions C6T channel and components guaranteed to meet or exceed proposed TIA/EIA Category standards KRONE Product Catalog MK005-01.I07 TrueNet™ Performance Requirements HighBand™ Jack to HighBand Jack Safety/Ratings: (on individual components as appropriate) n UL subject 444 n (UL) c(UL) Type MPR/CMR/CMG or MPP/CMP n NEC 800 type CMR or CMP n ICEA S-90-661 n ISO/IEC Class E n TIA/EIA 568 Category 5e, Category 6*, Draft n NEMA WC 66-1999 Category C6T 100-meter Channel 80 Cat PSNEXT Cat Attenuation dB 60 40 Acceptable Channels: n Two connections, consisting of a main distribution frame and station n Three connections, consisting of a main distribution frame, equipment field and station n Four connections, consisting of a main distribution frame, equipment field, consolidation point and station TrueNet™ Cabling Channel Configurations: 20 0 50 100 150 200 250 Frequency (MHz) Chart depicts representative data utilizing HighBand jack in the telecom closet, 90 meters of TrueNet C6T horizontal cable, HighBand jack at the workstation, and C6T TruePatch™ patch cords Warranty Coverage: n 20-Year Electrical n 5-Year Throughputn 20-Year Electrical Coverage: n Application assurance for network protocols specified by TIA/EIA 568-A n All components and installed channel guaranteed to pass passive electrical specifications: –PowerSum ACRs –PowerSum NEXTs –PowerSum ELFEXTs –Attenuations –Impedances –Delay Skews –Return Losss 5-Year Throughput Coverage: Active Electrical Specifications: CRC (Bit) Errors Zero per IEEE 802.3xx** Rise Time/Fall Time to IEEE 802.3xx** Amplitude to IEEE 802.3xx** **IEEE supplement applicable to network in use NOTE: The tables of discrete values contained in this document are for reference only Actual Compliance testing is based on swept frequency measurements to requirements as defined in TIA/EIA Category 5e documentation This sheet is provided for engineering and information purposes only Actual guaranteed performance is governed by the TrueNet warranty documentation Channel testing conducted by a UL Certified test lab * See TrueNet Warranty documentation for latest draft compliance Renewable 5-year warranty s See warranty documentation for specific specification details n KRONE Product Catalog MK005-01.I07 http://www.kroneamericas.com 2-11 TrueNet™ Performance Requirements C6T Supported Applications: Active Network Specifications n IEEE Input Specification Limits/100Base-T n n 10/100/1000Base-T (IEEE 802.3xx) 4/16 Mbps Token Ring 25,155,622 Mbps ATM Spec Positive Amplitude: Negative Amplitude: Amplitude Symmetry: Rise Time: Fall Time: Rise Time/Fall Time Symmetry: Jitter: TrueNet™ Cabling Ultim8™ Termination Block to HighBand™ Jack Min 0.95V 0.95V 0.98% ns ns ns 0% Max 1.05V 1.05V 1.02% ns ns 0.5 ns 1.4% 100-Meter Channel Passive Electrical Specifications Freq (MHz) Attenuation (dB) [min] 10 16 20 25 31.25 62.5 100 150 200 250 2.1 4.0 5.6 6.3 8.0 9.0 10.1 11.3 16.3 21.0 26.1 30.6 34.6 PowerSum NEXT (dB) PowerSum ACR (dB) [typical] [min] [typical] [min] [typical] [min] [typical] 0.6 3.0 4.4 5.0 6.6 7.5 8.5 9.7 14.4 19.0 24.1 28.7 32.9 70.3 60.6 55.6 54.0 51.0 49.0 47.4 45.7 40.6 37.1 34.0 31.9 30.2 77.8 69.1 64.8 63.4 60.5 59.1 57.7 56.3 51.9 49.0 46.4 44.6 43.3 68.2 56.6 50.0 47.7 42.6 40.0 37.3 34.4 24.3 16.2 8.0 1.3 -4.5 73.0 69.4 64.7 62.8 58.2 55.7 53.0 50.0 39.6 31.5 23.8 18.0 13.2 21 21 21 21 21 21 20 19 16 14 12 11 10 32 32 32 32 32 32 30 29 25 22 20 18 17 Characteristic Impedance For Cable: Channel Propagation Phase Delay: Channel Delay Skew: Ω) 100Ω Ω (±3Ω @ 100 MHz 548 ns 30 ns n n n 2-12 Return Loss (dB) http://www.kroneamericas.com Minimum values [min] represent the worst case allowable in a TrueNet system Minimum TrueNet values are derived from and meet or exceed proposed TIA/EIA Category values Typical values [typical] were obtained from passive testing over a 100-meter channel in a UL certified laboratory under controlled conditions C6T channel and components guaranteed to meet or exceed proposed TIA/EIA Category standards KRONE Product Catalog MK005-01.I07 TrueNet™ Performance Requirements Ultim8™ Termination Block to HighBand™ Jack C6T 100-meter Channel -100 -90 Cat PSNEXT Cat Attenuation -80 -70 dB -60 -50 Acceptable Channels: n Two connections, consisting of a main distribution frame and station n Three connections, consisting of a main distribution frame, equipment field and station n Four connections, consisting of a main distribution frame, equipment field, consolidation point and station TrueNet™ Cabling Channel Configurations: -40 Safety/Ratings: (on individual components as appropriate) n UL subject 444 n (UL) c(UL) Type MPR/CMR/CMG or MPP/CMP n NEC 800 type CMR or CMP n ICEA S-90-661 n ISO/IEC Class E n TIA/EIA 568 Category 5e, Category 6*, Draft n NEMA WC 66-1999 Category -30 -20 -10 0 50 100 150 200 Frequency (MHz) 250 300 350 Chart depicts representative data utilizing Ultim8 block in the telecom closet, Ultim8 block at the consolidation point, 90 meters of TrueNet horizontal cable, HighBand jack at the workstation, and C6T TruePatch™ patch cords Warranty Coverage: n n 20-Year Electrical 5-Year Throughputn 20-Year Electrical Coverage: n Application assurance for network protocols specified by TIA/EIA 568-A n All components and installed channel guaranteed to pass passive electrical specifications: –PowerSum ACRs –PowerSum NEXTs –PowerSum ELFEXTs –Attenuations –Impedances –Delay Skews –Return Losss 5-Year Throughput Coverage: Active Electrical Specifications: CRC (Bit) Errors Zero per IEEE 802.3xx** Rise Time/Fall Time to IEEE 802.3xx** Amplitude to IEEE 802.3xx** **IEEE supplement applicable to network in use NOTE: The tables of discrete values contained in this document are for reference only Actual Compliance testing is based on swept frequency measurements to requirements as defined in TIA/EIA Category 5e documentation This sheet is provided for engineering and information purposes only Actual guaranteed performance is governed by the TrueNet warranty documentation Channel testing conducted by a UL Certified test lab * See TrueNet Warranty documentation for latest draft compliance n Renewable 5-year warranty s See warranty documentation for specific specification details KRONE Product Catalog MK005-01.I07 http://www.kroneamericas.com 2-13 TrueNet™ Performance Requirements TM C5eT Supported Applications: n n n Active Network Specifications 10/100/1000Base-T (IEEE 802.3xx, 1000Base-T requires enhanced DSP electronics) 4/16 Mbps Token Ring 25,155,622 Mbps ATM IEEE Input Specification Limits/100Base-T Spec Positive Amplitude: Negative Amplitude: Amplitude Symmetry: Rise Time: Fall Time: Rise Time/Fall Time Symmetry: Jitter: TrueNet™ Cabling Enhanced Patch Panel to K600 Jack Min 0.95V 0.95V 0.98% ns ns ns 0% Max 1.05V 1.05V 1.02% ns ns 0.5 ns 1.4% 100-Meter Channel Passive Electrical Specifications Freq (MHz) Attenuation (dB) [min] 10 16 20 25 31.25 62.5 100 2.2 4.5 6.3 7.1 9.1 10.2 11.4 12.9 18.6 24.0 PowerSum NEXT (dB) PowerSum ACR (dB) [typical] [min] [typical] [min] [typical] [min] [typical] 1.6 3.2 4.6 5.2 6.6 7.4 8.4 9.5 13.9 18.1 62.9 53.0 48.0 46.3 42.9 41.2 39.6 37.9 32.7 29.2 83.7 71.5 65.5 63.5 59.4 57.4 55.5 53.5 47.5 43.4 60.7 48.5 41.7 39.2 33.8 31.0 28.2 25.0 14.1 5.2 66.8 67.6 64.1 62.4 57.9 55.3 52.5 49.4 38.0 28.7 19 19 19 19 19 19 18 17 14 12 32.0 32.0 32.0 32.0 32.0 32.0 30.7 29.5 25.7 23.1 Characteristic Impedance For Cable: Channel Propagation Phase Delay: Channel Delay Skew: Ω) 100Ω Ω (±3Ω @ 100 MHz 548 ns 30 ns n n n 2-14 Return Loss (dB) http://www.kroneamericas.com Minimum values [min] represent the worst case allowable in a TrueNet system Minimum TrueNet values are derived from and meet or exceed proposed TIA/EIA Category 5e values Typical values [typical] were obtained from passive testing over a 100-meter channel in a UL certified laboratory under controlled conditions C5eT channel and components guaranteed to meet or exceed proposed TIA/EIA Category 5e standards KRONE Product Catalog MK005-01.I07 TrueNet™ Performance Requirements Safety/Ratings: (on individual components as appropriate) n UL subject 444 n (UL) c(UL) Type MPR/CMR/CMG or MPP/CMP n NEC 800 type CMR or CMP n ICEA S-90-661 n ISO/IEC Class D n TIA/EIA 568-A Category 5e Warranty Coverage: n n 20-Year Electrical 5-Year Throughputn 20-Year Electrical Coverage: n Application assurance for network protocols specified by TIA/EIA 568-A n All components and installed channel guaranteed to pass passive electrical specifications: –PowerSum ACR –PowerSum NEXT –PowerSum ELFEXT –Attenuation –Impedance –Delay Skew –Return Loss C5eT 100-meter Channel 80 Cat 5e PSNEXT Cat 5e Attenuation 60 40 Acceptable Channels: n Two connections, consisting of a main distribution frame and station n Three connections, consisting of a main distribution frame, equipment field and station n Four connections, consisting of a main distribution frame, equipment field, consolidation point and station TrueNet™ Cabling Channel Configurations: TM dB Enhanced Patch Panel to K600 Jack 20 0 50 100 150 200 250 Frequency (MHz) Chart depicts representative data utilizing Enhanced Patch Panel in the telecom closet, 90 meters of TrueNet C5eT horizontal cable, K600 jack at the workstation, and C5eT TruePatch™ patch cords 5-Year Throughput Coverage: Active Electrical Specifications: CRC (Bit) Errors Zero per IEEE 802.3xx** Rise Time/Fall Time to IEEE 802.3xx** Amplitude to IEEE 802.3xx** **IEEE supplement applicable to network in use NOTE: The tables of discrete values contained in this document are for reference only Actual Compliance testing is based on swept frequency measurements to requirements as defined in TIA/EIA Category 5e documenation This sheet is provided for engineering and information purposes only Actual guaranteed performance is governed by the TrueNet warranty documentation Channel testing conducted by a UL Certified test lab n Renewable 5-year warranty KRONE Product Catalog MK005-01.I07 http://www.kroneamericas.com 2-15 TrueNet™ Performance Requirements TM C5eT Supported Applications: Active Network Specifications n IEEE Input Specification Limits/100Base-T n n 10/100/1000Base-T (IEEE 802.3xx, 1000Base-T requires enhanced DSP electronics) 4/16 Mbps Token Ring 25,155,622 Mbps ATM Spec Positive Amplitude: Negative Amplitude: Amplitude Symmetry: Rise Time: Fall Time: Rise Time/Fall Time Symmetry: Jitter: TrueNet™ Cabling K600 Jack to K600 Jack Min 0.95V 0.95V 0.98% ns ns ns 0% Max 1.05V 1.05V 1.02% ns ns 0.5 ns 1.4% 100-Meter Channel Passive Electrical Specifications Freq (MHz) Attenuation (dB) [min] 10 16 20 25 31.25 62.5 100 2.2 4.5 6.3 7.1 9.1 10.2 11.4 12.9 18.6 24.0 PowerSum NEXT (dB) PowerSum ACR (dB) [typical] [min] [typical] [min] [typical] [min] [typical] 1.7 3.3 4.6 5.2 6.7 7.5 8.5 9.5 14.0 18.2 62.9 53.0 48.0 46.3 42.9 41.2 39.6 37.9 32.7 29.2 80.6 68.9 63.1 61.2 57.3 55.4 53.5 51.7 45.8 41.9 60.7 48.5 41.7 39.2 33.8 31.0 28.2 25.0 14.1 5.2 66.4 64.9 60.5 58.6 53.9 51.2 48.3 45.1 33.8 24.8 19 19 19 19 19 19 18 17 14 12 31.7 31.7 31.7 31.7 31.7 31.7 30.7 29.7 26.7 24.7 Characteristic Impedance For Cable: Channel Propagation Phase Delay: Channel Delay Skew: Ω) 100Ω Ω (±3Ω @ 100 MHz 548 ns 30 ns n n n 2-16 Return Loss (dB) http://www.kroneamericas.com Minimum values [min] represent the worst case allowable in a TrueNet™ system Minimum TrueNet values are derived from and meet or exceed proposed TIA/EIA Category 5e values Typical values [typical] were obtained from passive testing over a 100-meter channel in a UL certified laboratory under controlled conditions C5eT channel and components guaranteed to meet or exceed proposed TIA/EIA Category 5e standards KRONE Product Catalog MK005-01.I07 TrueNet™ Performance Requirements TM K600 Jack to K600 Jack Safety/Ratings: (on individual components as appropriate) n UL subject 444 n (UL) c(UL) Type MPR/CMR/CMG or MPP/CMP n NEC 800 type CMR or CMP n ICEA S-90-661 n ISO/IEC Class D n TIA/EIA 568-A Category 5e Warranty Coverage: n n C5eT 100-meter Channel 80 Cat 5e PSNEXT Cat 5e Attenuation dB 60 40 Acceptable Channels: n Two connections, consisting of a main distribution frame and station n Three connections, consisting of a main distribution frame, equipment field and station n Four connections, consisting of a main distribution frame, equipment field, consolidation point and station TrueNet™ Cabling Channel Configurations: 20 0 50 100 150 200 250 Frequency (MHz) Chart depicts representative data utilizing K600 jack in the telecom closet, 90 meters of TrueNet C5eT horizontal cable, K600 jack at the workstation, and C5eT TruePatch™ patch cords 20-Year Electrical 5-Year Throughputn 5-Year Throughput Coverage: 20-Year Electrical Coverage: n Application assurance for network protocols specified by TIA/EIA 568-A n All components and installed channel guaranteed to pass passive electrical specifications: –PowerSum ACR –PowerSum NEXT –PowerSum ELFEXT –Attenuation –Impedance –Delay Skew –Return Loss Active Electrical Specifications: CRC (Bit) Errors Zero per IEEE 802.3xx** Rise Time/Fall Time to IEEE 802.3xx** Amplitude to IEEE 802.3xx** **IEEE supplement applicable to network in use NOTE: The tables of discrete values contained in this document are for reference only Actual Compliance testing is based on swept frequency measurements to requirements as defined in TIA/EIA Category 5e documenation This sheet is provided for engineering and information purposes only Actual guaranteed performance is governed by the TrueNet warranty documentation Channel testing conducted by a UL Certified test lab n Renewable 5-year warranty KRONE Product Catalog MK005-01.I07 http://www.kroneamericas.com 2-17 TrueNet™ Performance Requirements TM C5eT Supported Applications: Active Network Specifications n IEEE Input Specification Limits/100Base-T n n 10/100/1000Base-T (IEEE 802.3xx, 1000Base-T requires enhanced DSP electronics) 4/16 Mbps Token Ring 25,155,622 Mbps ATM Spec Positive Amplitude: Negative Amplitude: Amplitude Symmetry: Rise Time: Fall Time: Rise Time/Fall Time Symmetry: Jitter: TrueNet™ Cabling UMS/Mini Patch Panel to K600 Jack Min 0.95V 0.95V 0.98% ns ns ns 0% Max 1.05V 1.05V 1.02% ns ns 0.5 ns 1.4% 100-Meter Channel Passive Electrical Specifications Freq (MHz) Attenuation (dB) [min] 10 16 20 25 31.25 62.5 100 2.2 4.5 6.3 7.1 9.1 10.2 11.4 12.9 18.6 24.0 PowerSum NEXT (dB) PowerSum ACR (dB) [typical] [min] [typical] [min] [typical] [min] [typical] 0.5 3.1 4.9 5.6 7.4 8.4 9.5 10.7 15.8 20.5 62.9 53.0 48.0 46.3 42.9 41.2 39.6 37.9 32.7 29.2 69.1 59.2 54.3 52.7 49.4 47.8 46.2 44.6 39.7 36.3 60.7 48.5 41.7 39.2 33.8 31.0 28.2 25.0 14.1 5.2 64.6 60.0 54.8 52.8 47.7 45.0 42.1 39.0 28.1 19.6 19 19 19 19 19 19 18 17 14 12 32.4 32.4 32.4 32.4 32.4 32.4 30.8 29.3 24.5 21.3 Characteristic Impedance For Cable: Channel Propagation Phase Delay: Channel Delay Skew: Ω) 100Ω Ω (±3Ω @ 100 MHz 548 ns 30 ns n n n 2-18 Return Loss (dB) http://www.kroneamericas.com Minimum values [min] represent the worst case allowable in a TrueNet™ system Minimum TrueNet values are derived from and meet or exceed proposed TIA/EIA Category 5e values Typical values [typical] were obtained from passive testing over a 100-meter channel in a UL certified laboratory under controlled conditions C5eT channel and components guaranteed to meet or exceed proposed TIA/EIA Category 5e standards KRONE Product Catalog MK005-01.I07 TrueNet™ Performance Requirements Safety/Ratings: (on individual components as appropriate) n UL subject 444 n (UL) c(UL) Type MPR/CMR/CMG or MPP/CMP n NEC 800 type CMR or CMP n ICEA S-90-661 n ISO/IEC Class D n TIA/EIA 568-A Category 5e Warranty Coverage: n n C5eT 100-meter Channel 80 Cat 5e PSNEXT Cat 5e Attenuation 60 40 Acceptable Channels: n Two connections, consisting of a main distribution frame and station n Three connections, consisting of a main distribution frame, equipment field and station n Four connections, consisting of a main distribution frame, equipment field, consolidation point and station TrueNet™ Cabling Channel Configurations: TM dB UMS/Mini Patch Panel to K600 Jack 20 0 50 100 150 200 250 Frequency (MHz) Chart depicts representative data utilizing UMS/Mini Patch Panel in the telecom closet, 90 meters of TrueNet C5eT horizontal cable, K600 jack at the workstation, and C5eT TruePatch™ patch cords 20-Year Electrical 5-Year Throughputn 20-Year Electrical Coverage: n Application assurance for network protocols specified by TIA/EIA 568-A n All components and installed channel guaranteed to pass passive electrical specifications: –PowerSum ACR –PowerSum NEXT –PowerSum ELFEXT –Attenuation –Impedance –Delay Skew –Return Loss 5-Year Throughput Coverage: Active Electrical Specifications: CRC (Bit) Errors Zero per IEEE 802.3xx** Rise Time/Fall Time to IEEE 802.3xx** Amplitude to IEEE 802.3xx** **IEEE supplement applicable to network in use NOTE: The tables of discrete values contained in this document are for reference only Actual Compliance testing is based on swept frequency measurements to requirements as defined in TIA/EIA Category 5e documenation This sheet is provided for engineering and information purposes only Actual guaranteed performance is governed by the TrueNet warranty documentation Channel testing conducted by a UL Certified test lab n Renewable 5-year warranty KRONE Product Catalog MK005-01.I07 http://www.kroneamericas.com 2-19 TrueNet™ Performance Requirements TM C5eT Supported Applications: Active Network Specifications n IEEE Input Specification Limits/100Base-T n n 10/100/1000Base-T (IEEE 802.3xx, 1000Base-T requires enhanced DSP electronics) 4/16 Mbps Token Ring 25,155,622 Mbps ATM Spec Positive Amplitude: Negative Amplitude: Amplitude Symmetry: Rise Time: Fall Time: Rise Time/Fall Time Symmetry: Jitter: TrueNet™ Cabling 25-Pair FT (Feed-Thru) Block to K600 Jack Min 0.95V 0.95V 0.98% ns ns ns 0% Max 1.05V 1.05V 1.02% ns ns 0.5 ns 1.4% 100-Meter Channel Passive Electrical Specifications Freq (MHz) [min] 10 16 20 25 31.25 62.5 100 PowerSum NEXT (dB) Attenuation (dB) 2.2 4.4 6.3 7.1 9.0 10.1 11.3 12.8 18.5 23.8 PowerSum ACR (dB) [typical] [min] [typical] [min] [typical] [min] [typical] 0.9 3.3 5.0 5.7 7.5 8.4 9.6 10.8 15.9 20.7 62.9 53.0 48.0 46.4 43.0 41.3 39.6 37.9 32.7 29.2 69.1 60.2 55.7 54.2 51.2 49.7 48.3 46.8 42.3 39.3 60.6 48.6 41.7 39.2 33.9 31.2 28.3 25.2 14.3 5.3 63.0 59.9 55.3 53.4 48.7 46.2 43.4 40.4 29.9 21.6 19 19 19 19 19 19 18 17 14 12 26 26 26 26 26 26 26 25 22 21 Characteristic Impedance For Cable: Channel Propagation Phase Delay: Channel Delay Skew: Ω) 100Ω Ω (±3Ω @ 100 MHz 548 ns 30 ns n n n 2-20 Return Loss (dB) http://www.kroneamericas.com Minimum values [min] represent the worst case allowable in a TrueNet™ system Minimum TrueNet values are derived from and meet or exceed proposed TIA/EIA Category 5e values Typical values [typical] were obtained from passive testing over a 100-meter channel in a UL certified laboratory under controlled conditions C5eT channel and components guaranteed to meet or exceed proposed TIA/EIA Category 5e standards KRONE Product Catalog MK005-01.I07 ... 17 4-* * 6644 17 8-* * 6644 15 2-* * 6644 15 4-* * 6644 15 6-* * 6644 15 7-* * Catalog Pages 8-2 8-2 8-2 8-2 8-4 8-4 8-4 8-3 8-3 8-3 8-3 9-3 4-2 4-6 4-6 4-6 4-6 4-6 4-6 4-6 4-6 8-1 1 8-1 1 8-1 1 8-1 1 1 0-6 1 0-6 ... 17 4-* * 6644 17 8-* * 6644 15 2-* * 6644 15 4-* * 6644 15 6-* * 6644 15 7-* * 3-4 3-4 3-4 3-4 3-4 8-1 0 8-1 0 8-1 0 8-1 0 1 0-3 1 0-4 9-6 9-6 9-7 9-7 9-7 9-8 2 2 1 80 0-* * 16 5-0 0 05 4-0 1 76 0-2 4 00 3-2 4 00 3-4 8 06 0-0 6... 59 6-0 6 51 0-0 6 Catalog Pages 9-2 7-3 8-7 8-7 8-7 8-7 3-2 3-3 3-3 For *** substitute BL-blue GY-gray WT-white GN-green YL-yellow RD-red http://www.kroneamericas.com KRONE Product Catalog MK00 5-0 1.I07