LoopStar ® 714 and LoopStar ® 718 Extend Ethernet Services to All Customers Over Readily Available T1/E1 Facilities We all hear about the glut of fiber in the ground today. Unfortunately not much of it really exists in the last mile. T1s and E1s are still the primary mode of transport for a majority of locations. So how do you provide economical business-class Ethernet services to your off-net customer locations that can only be reached through T1s or E1s? How do you offer Ethernet bandwidth and cost savings to customers who thought they could only get Frame Relay service, speeds and pricing? The LoopStar 714 and LoopStar 718 are tailored to help service providers reach their off-net customers and reduce service fees at the same time. The LoopStar 714 offers highly manageable 10/100 customer access and up to four T1/E1s (eight T1/E1s for the LoopStar 718) for the network connection. These T1/E1s are bonded using the standard Multilink Point-to-Point Protocol (MLPPP), offering up to 12 Mb/s (T1) or 16 Mb/s (E1) of service. Additional lines can be added as necessary, and with a simple-to-use Graphical User Interface (GUI), provisioning new circuits has never been easier. And the LoopStar products come equipped with LoopStar 700 intelligent management, designed to support remote service provisioning, verification, and troubleshooting. From RMON counters and Ethernet / WAN loopbacks to a built-in Ethernet port Time Domain Reflectometry (TDR) test, from complete Layer 2+ classification and service definition to link quality monitoring and reporting, the LoopStar 714 and LoopStar 718 provide the flexibility and scalability to deliver customer- specific solutions and support with pinpoint accuracy. Flexible and Differentiated Ethernet Solutions Offering business-class Ethernet services by providing strong Class of Service (CoS) features, the LoopStar 714 and LoopStar 718 can be used for: • Point-to-point and hub-and-spoke deployments • Full range of 4,096 Virtual LANs • Layer 2 Virtual Private Networks (VPNs) • Traffic prioritization and classification For example, with the advanced traffic classification features of the LoopStar 714 and LoopStar 718, Voice over IP (VoIP) traffic can be given priority over Internet access traffic. The LoopStar products support up to 10 rule- based classifications based on any of the following inputs: VLAN ID, VLAN P-bits, ToS bits and DiffServ Code Points. In addition to this classification scheme, rate limiting and policing are also provided to round out a full suite of tools for customer provisioning and service. SPEC SHEET SPEC SHEET www.adc.com • +1-952-938-8080 • 1-800-366-3891 Features • Multilink Point-to-Point Protocol (MLPPP) • ‘Plug-and-play’ platform and design • LoopStar 700 Intelligent Management Capabilities • LoopStar 700 Traffic Management • LoopStar 700 Performance and Fault Management 01/06 • 102157AE LoopStar ® 714 and LoopStar ® 718 LoopStar ® 714 and LoopStar ® 718 Extend Ethernet Services to All Customers Over Readily Available T1/E1 Facilities 2 www.adc.com • +1-952-938-8080 • 1-800-366-3891 Benefits • Cost-effective approach to deliver Ethernet services over NxT1 and NxE1 • ‘Plug-and-Play’ design for easy installation, configuration and management • Proven management software with comprehensive and robust features • Standard MLPPP bonding means T1/E1s can be added as customer bandwidth needs grow • Simple replacement for Frame Relay services • Bond from 1-8 T1/Es to provide bandwidth ranging from 1.5 Mb/s to 16 Mb/s; automatic removal / restoration of failed links • Compact design makes it simple to install at the customer premise, either as a wall-mounted or rack-mounted unit • Allow for easy access to configure or disable access and ports from anywhere; secure in-band management access from anywhere on the network • Customer traffic classification, supporting up to 10 traffic rules per device, as well as VLAN management, traffic queuing, rate limiting and policing • Support for both Layer 1 and Layer 2 performance monitoring statistics, as well as facility alarms available over both the in-band management channel and the local management console port • Built-in loopbacks and a built-in Ethernet port Time Domain Reflectometer keep service calls to a minimum Easy Fit into Existing OAM&P Infrastructure In conjunction with the LoopStar 700 suite’s in-band management VLAN channel, robust GUI and full SNMP connectivity, the LoopStar 714 and LoopStar 718 are easy to configure, manage and monitor. Performance monitoring is supported for both the T1/E1 and Ethernet interfaces. Fault management is covered through the use of equipment and facility alarms available over both the in-band management channel and through the local management console port. The LoopStar 714 and LoopStar 718 provide a strong set of carrier operational support tools, which extend beyond standard T1/E1 loopback testing and reach all the way to the user-facing Ethernet port. The LoopStar 714 and LoopStar 718 complement the LoopStar 700 product line, enabling service providers to create new business service revenues by delivering high-margin Ethernet services to all of their customers, no matter where they are located on the network. Bonded T1/E1s T1/E1 Ethernet Switch/Router Ethernet VoIP PBX Core LS 750 LS 714 LS 718 The LoopStar 714 and LoopStar 718 offer business-class Ethernet to any size location. 01/06 • 102157AE LoopStar ® 714 and LoopStar ® 718 LoopStar ® 714 and LoopStar ® 718 Extend Ethernet Services to All Customers Over Readily Available T1/E1 Facilities 3 www.adc.com • +1-952-938-8080 • 1-800-366-3891 Specifications Interfaces: 1 x 10/100Base-T port 1 x 100Base-FX (SM or MM SFP) 8 x T1/E1 interfaces, supports 1 MLPPP bundle (LoopStar 718) 4 x T1/E1 interfaces, supports 1 MLPPP bundle (LoopStar 714) 1 x 10/100 management port Maintenance: T1/E1 loopbacks and PM Ethernet loopbacks and PM Ethernet cable testing with TDR WAN Protocol: RFC1661: Point-to-Point Protocol (PPP) and Link Control Protocol (LCP) RFC1990: PPP Multilink Protocol (ML-PPP) RFC3518: Bridging Control Protocol (BCP) Automatic removal/restoration of failed links Ethernet Services: 802.1p prioritization 802.1Q VLAN tagging/switching/stacking Rate limiting: 128-500 kb/s increments CoS: WRR or strict priority based on VLAN, p-bits or ToS/DSCP Management: IP host with DHCP client for automatic address assignment In-band management VLAN Web-based management interface (GUI) SNMP agent supporting standard MIBs, including RMON FTP client for download LoopStar 700 intelligent management Power Options: AC Power: 100-240 V auto ranging, 47-63Hz DC Power: Dual DC Feeds -48 VDC nominal (-40 to -60 VDC) or 24 VDC Physical: 1 RU (1.75" x 17" x 7.25") Wall-mount or rack-mount (19" and 23") Full front access (ETSI form factor) Temperature hardened (option) -40° to +65° C (operating) -40° to +70° C (storage) Regulatory: UL Listed EN/UL 60950 CE Mark FCC Part 15 Class B NEBS Level 3 certified ADC Telecommunications, Inc., P.O. Box 1101, Minneapolis, Minnesota USA 55440-1101 Specifications published here are current as of the date of publication of this document. Because we are continuously improving our products, ADC reserves the right to change specifications without prior notice. At any time, you may verify product specifications by contacting our headquarters office in Minneapolis. ADC Telecommunications, Inc. views its patent portfolio as an important corporate asset and vigorously enforces its patents. Products or features contained herein may be covered by one or more U.S. or foreign patents. An Equal Opportunity Employer 102154AE 1/06 Original © 2006 ADC Telecommunications, Inc. All Rights Reserved Web Site: www.adc.com From North America, Call Toll Free: 1-800-366-3891 • Outside of North America: +1-952-938-8080 Fax: +1-952-917-3237 • For a listing of ADC’s global sales office locations, please refer to our web site. SPEC SHEET Ordering Information Description Catalog Number LPS-714 AC Package (1 10/100, 1FX, no optics, 4-T1/E1) *Includes: 1 AC power supply and AC power cord, 19” and 23” LPS-714-AC L1 rack mount brackets, license for basic software and documentation LPS-714 DC Package, Temperature Hardened (1 10/100BT, 1FX, no optics, 4-T1/E1) *Includes: Internal dual feed - 48Vdc power supply, 19” and 23” LPS-714-48DC L1 rack mount brackets, license for basic software and documentation LPS-714 24DC Package, Temperature Hardened (1 10/100BT, 1FX, no optics, 4-T1/E1) *Includes: Internal dual feed - 24Vdc power supply, 19” and 23” LPS-714-24DC L1 rack mount brackets, license for basic software and documentation LPS-718 AC Package, (1 10/100BT, 1FX, no optics, 8-T1/E1) *Includes: 1 AC power supply and AC power cord, 19” and 23” LPS-718-AC L1 rack mount brackets, license for basic software and documentation LPS-718 48VDC Temperature Hardened, (1 10/100BT, 1FX, no optics, 8-T1/E1) *Includes: Internal dual feed -48dc power supply, 19” and 23” LPS-718-48DC L1 rack mount brackets, license for basic software and documentation LPS-718 24DC Temperature Hardened, (1 10/100BT, 1FX, no optics, 8-T1/E1) *Includes: Internal dual feed -24Vdc power supply, 19” and 23” LPS-718-24DC L1 rack mount brackets, license for basic software and documentation . LoopStar ® 714 and LoopStar ® 718 LoopStar ® 714 and LoopStar ® 718 Extend Ethernet Services to All Customers Over Readily Available T1/E1 Facilities 3. LoopStar ® 714 and LoopStar ® 718 Extend Ethernet Services to All Customers Over Readily Available T1/E1 Facilities We all hear about the glut