✁ ✂ ✄☎ ✆ ✂ ✝ ✞ ✟ ✠☛✡ ☞ ✌ 1. Colored face is behind. Rabbit ear on both sides. 4. Valley fold down at right angle. 5. Unfold back to step 4. 3-5 in mirror image. 6. Repeat steps 3 to 5 7. Open lower flap while raising 8. Inverse rabbit ear top flap. 9. Squash fold up. 10. Valley fold down. 11. Squash fold the white flap. 2. Swing upper flap down behind. it up, using existing creases. 3. Valley fold lower flap at . right angle. Precrease upper left flap at angle bisector. ✍✎ ✠☛✏ ✡ ✑ ✡ ✒ ✑ ✟ ✓ ✔☛✕ ✖ ✖ ✖ ✗✘ ✙ ✚✛ ✜ ✙ ✢ ✣✥✤ ✦☛✧★ ✩ 24. Squash fold on both sides. 13. Valley fold white flap to the left. 14. Valley fold one flap down (some paper has to be 16. Petal fold.15. Squash fold front flap. 17. Flip white flap to the left. Repeat steps 13 to 16 in mirror image. 13-16 12. Petal fold the white flap. Then flip the back flap up. pulled out.) right angle to form the arms. 18. Valley fold both flaps at 19. Precrease so that both corners meet in the center. Note the black dots, used as reference on step 21. 20. Valley fold down 21. Valley fold up so that the crease meets the black dots marked on step 19. 23. Squash fold the small triangular flap. (part of it is hidden behind the horizontal flap) 22. Turn Over ✪✫ ✦☛✬ ✗ ✧✭ ✧✮ ✭ ✤ ✯ ✰ ★ ✱ ✱ ✱ ✲✳ ✴ ✵✶ ✷ ✴ ✸ ✹✥✺ ✻☛✼ ✽ ✾ 30. Open both flaps. Model wont lie flat. facultative). flaps to front. (These steps are inside poket, raise two triangulars 25. Hide both upper flaps 31. Montain fold behind using existing crease. 32. Close flaps back. 33. Valley fold at angle bissector. 34. Valley fold down. 35. valley fold up. 36. Precrease at right angle. in half while making a rabbit ear at the top to form the head. 37. Mountain fold the model then unfold to step 27. 28. Precrease in half. 29. Precrease in half, 24. Squash fold on both sides. 26. Precrease, then turn over. 27. Valley fold down using crease made on step 26. 23(bis). Valley fold on both sides using existing creases. ✿❀ ✻☛❁ ✲ ✼❂ ✼❃ ❂ ✺ ❄ ❅☛❆ ❇ ❇ ❇ ❈❉ ❊ ❋● ❍ ❊ ■ ❏✥❑ ▲☛▼◆ ❖ 38. Inside reverse fold where indicated, to form the arms. Shape the head using montain fold and pushing it slightly down (it will make it 3D). Crimp the legs to form the feet. 29. Round the body by inserting a finger between the two main flaps. 40. The two pointed flaps can be raised a little and tucked inside one another to somewhat close the model in a rounded shape. 41. finished. ◗ ▲☛❘ ❈ ▼❙ ▼❚ ❙ ❑ ❯ ❱☛❲ ❳ ❳ ❳ . then unfold to step 27 . 28 . Precrease in half. 29 . Precrease in half, 24 . Squash fold on both sides. 26 . Precrease, then turn over. 27 . Valley fold down. used as reference on step 21 . 20 . Valley fold down 21 . Valley fold up so that the crease meets the black dots marked on step 19. 23 . Squash fold the small