DVB-T2 (Digital Video Broadcasting – Second Generation Terrestrial) is the extension of the television standard DVB-T. This system transmits compressed digital audio, video, and other data in PLPs (physical layer pipes), using OFDM modulation with channel coding and interleaving. This paper provides the performance evaluation of DVB-T2 for outdoor reception by the received signal measurement.
See discussions, stats, and author profiles for this publication at: https://www.researchgate.net/publication/292881640 Performance evaluation of DVB-T2 for outdoor reception Conference Paper · February 2016 CITATION READS 66 2 authors, including: Bundit Ruckveratham King Mongkut's Institute of Technology Ladkrabang 7 PUBLICATIONS 4 CITATIONS SEE PROFILE All content following this page was uploaded by Bundit Ruckveratham on 03 February 2016 The user has requested enhancement of the downloaded file All in-text references underlined in blue are added to the original document and are linked to publications on ResearchGate, letting you access and read them immediately Performance evaluation of DVB-T2 for outdoor reception Bundit Ruckveratham Sathaporn Promwong Department of Telecommunication Engineering, Faculty of Engineering King Mongkut’s Institute of Technology Ladkrabang Bangkok, Thailand bundit1973@hotmail.com Department of Telecommunication Engineering, Faculty of Engineering King Mongkut’s Institute of Technology Ladkrabang Bangkok, Thailand kpsathap@kmitl.ac.th Abstract - DVB-T2 (Digital Video Broadcasting – Second Generation Terrestrial) is the extension of the television standard DVB-T This system transmits compressed digital audio, video, and other data in PLPs (physical layer pipes), using OFDM modulation with channel coding and interleaving This paper provides the performance evaluation of DVB-T2 for outdoor reception by the received signal measurement The field measurements were taken in Bangkok of Thailand, along 50 locations The receiver used to analyze the DVB-T2 signal providing several quality measurements (Power, C/N, MER, BER, constellation diagram, etc.).The results of the study could be useful for the improvement of DVB-T2 broadcast such as transmitter adjustment and gap filler transmitter installation to optimize the efficiency of digital television broadcasting Keywords— DVB-T2, Field strength, C/N, MER, BER I INTRODUCTION The standard television broadcasting for today have been chosen to digital transmission DVB-T2 (Digital Video Broadcasting – Second Generation Terrestrial) [1] system is the one of the popular digital television broadcasting system that used around the world This system was developed from DVBT (Digital Video Broadcasting — Terrestrial) [2] by DVB (Digital Video Broadcasting) DVB-T2 system can simultaneous transmission of multiple services and can be set different configuration and resistant for interference by the configuration selected DVB-T2 system is capable of broadcasting either fixed reception or mobile reception, depending on the configuration parameter Therefore, it supports for SD (Standard-definition television), HD (highdefinition television), UHD (Ultra-high-definition television), mobile TV, radio, or any combination of multiple digital broadcasting The broadcast efficiency evaluation is necessary for monitoring the results of the broadcasting In other research, there are research papers for evaluation minimum C/N signal can be received by the variation configuration parameters [3] The measurement performance of the portable reception [4] as well as the measurement for different location of urban and rural area However, few studies have reported on performance evaluation of DVB-T2 especially for outdoor reception The field measurements were taken in Bangkok of Thailand, along 50 locations The main topic for research are analyze the efficiency of the broadcast and evaluation the suitable configuration parameters of DVB-T2 that NBTC (National Broadcasting and Telecommunication Commission) recommend for broadcast the digital television in Thailand [5] The rest of the paper is organized as follows Section II explain about the parameter used for broadcasting Section III proposes the field measurement and analysis Additionally, Section IV shows performance of the result of measurement signals Finally, conclusions are drawn in Section V II THE PARAMETERS USED FOR BROADCASTING The Parameters of broadcasting is very important for the effect of received signal The DVB-T2 modulation parameters for transmission in Thailand was set by the NBTC The total of transmit data is 27.4 Mbps Each of the multiplexer (MUX) contain for eight channels There are divided by the standard definition television for channels with transfer data rate of each channel is approximately 1.28 -1.6 Mbps The Highdefinition television for channels with data transfer data rates of each channel is approximately 5.92-7.2 Mbps The transmission data rate depending on the modulation parameters configuration The parameters for DVB-T2 broadcasting summarized in Table I Table I The DVB-T2 modulation parameters for Thailand Parameter Bandwidth FFT Mode Pilot Pattern Guard Interval Constellation Constellation Rotation Code Rate Value MHz 16k Extended PP2 19/128 64 QAM Off 3/5 III THE FIELD MEASUREMENT AND ANALYSIS A The transmitter and antenna The field measurements were taken in Bangkok of Thailand, along 50 locations in Bangkok, from the 13th to 22th of October, 2014 Bangkok is a large city with a population of about 10 million people This city provides different reception environments, from dense urban areas to open space in the suburbs environments The main transmitter is located at the Baiyoke 2, latitude 13o 45 '16.77 "N, longitude 100o 32' 25.34" E The antenna height is 328 meters above the sea level, the antenna beam is 0.3 degrees The transmitter consisted with the DVB-T2 modulator and power amplifier The frequency of broadcasting comprising MUX There are channel 36 (594 MHz), 40 (626 MHz), 44 (658 MHz) and 52 (722 MHz) and the transmitter power is kW for each of MUX The antenna gain is 14.31 dBd and radiation pattern is horizontal polarization B Modulation Error Ratio The Modulation Error Ratio (MER) is used to indicate the efficiency of digital television transmission [6] The MER can be measured from the samples terminal of the transmitter and can be measured from the receiver of the field as well The Modulation format is QAM (Quadrature amplitude modulation) The MER performance shown in figure The constellation points used to inspect the errors amplitude and phase Those errors of vector are the result of the distortion frequency divided by the sum of the squares of the magnitudes of the symbol error vectors (δI j ,δQ j ) The result, expressed as a power ratio in dB, is defined as the Modulation Error Ratio (MER) (1) The standard deviation of MER is used to inspection the interference in the receive channel If the standard deviation of MER is high that mean the receive channel is more interference and low interference when the value of the standard of deviation is low (2) When 𝜎 is the standard deviation of MER, 𝑥 is the each MER value from each of sub frequency of OFDM (Orthogonal frequency-division multiplexing) 𝑥 ̅ is the average of the MER and N is the number of all sub frequency C Signal Detection The MER was measured from the DVB-T2 receiver analyzer via the antenna The received signal after demodulation will be measurement The approximate of MER at 20 dB to give Bit error rate (BER) about x 10 -2 This is the estimate of minimum threshold that accept to receive the digital television of DVB-T2 and television can watch normally By this point, is defined as the bBER or BER before LDPC (lowdensity parity-check) The BER after LDPC decoding is defined as the aBER or after BER that can be reduced the BER to x 10-7 After that, BEH (Bose-Chaudhuri-Hocquenghen) can be reduced the BER to x 10-11 [8] The block diagram of measurement is shown in figure Figure The block diagram of the measurement signal Figure The Constallation rotate and non rotate in DVB-T2 The error Vector of the IQ signal that comparison between the ideal signal and the error signal [7] The sum of the squares of the magnitudes of the ideal symbol vectors (I j , Q j ) is Those of measurement used receive antenna high meters above the ground level The receive antenna installed on the car roof The receiver analyzer measurement is Promax HD Ranger that is used for measurement for 50 locations around Bangkok The measurement taken from different distances and different environment from1 km to 38 km The locations of measurement are shown in figure and interference caused by the area where measurement, because some location has tall buildings and density of buildings That was making difficult for signal reception The comparison of frequencies is presented by the frequency of 722 MHz have more attenuation by distance more than the frequency 594 MHz and 658 MHz as the trend lines are shown Figure The positions of measurement, green mark is field measurement and red mark is transmitter station IV THE RESULT OF MEASUREMENT All of field measurements are use SFN (Single frequency network) [9] That means each of measurement point was measured by the one signal source and addition with reflect signal (Multipart) In some cases, the received signal strength in some locations are equal but the MER of received signal may not equal Because those areas are obscured by Interference of environment Figure The comparison of distance and C/N Figure shows the comparison between the distance and C/N The trend lines are shown when the distance increases the C/N are reduced Although in some cases for example, at the distance of approximately 18 kilometers The C/N is approximately 30 dB from the measurement, while at the distance of 12 km the C/N is approximately 27 dB It shows that at a distance closer than the received signal is below Because the point of measurement location at distance of 12 km have more obscure and interference by environment more than the measurement point at distance of 18 km This is the obstruction Figure The comparison of distance and MER The comparison of distance and MER is presented by if the distance increase the MER will decrease because the delay time of signal and the reflections of multipath effect on the environment is effect for received signal The delay time and the multipath effect making the phase and amplitude of frequency is shifted Those of results making the IQ signal were changed The results of MER affected from the distance change is shown in figure For example at the location point of distance is approximately 23 kilometers is presented by the MER is approximately 31 dB while at the location point of distance is approximately 11 kilometers the MER is approximately dB, because the area of the measurement at distance is approximately 23 kilometers the location is open space and no interference, as a results that give the MER measurements is approximately 31 dB, while at a distance is approximately 11 kilometers the MER is quite low and approximately dB, because that area has been overshadowed by interference The results as shown in Figure The trend lines shows the frequency of 722 MHz is increases the distance will make the MER is dropping faster than the frequency of 594 MHz and 658 MHz That means the high frequency are interference affected more than the low frequency The before Bit Error Rate (bBER) is used to measurement the BER before sent to the LDPC block The performance quality of received signal for digital television transmission DVB-T2 is indicated by the measurement of bBER The results are shown in figure When the MER is higher will make the bBER is decreased For example, at the point of MER is approximately 7.5 dB that make the bBER is approximately x 10-2 that is shown the bBER is more error very quickly The comparison between the MER at 18 dB to 35 dB will make the bBER is approximately 3x10-3 and the error of bBER is very low That means the minimum of MER is approximately 18 dB can be normally for receive DVB-T2 signal The comparison of frequencies is not different from the measurement The trend lines are shown in figure Figure The cumulative distribution function of MER Figure The comparison of MER and bBER From The measurement signal frequency of 50 locations and frequencies for this research Previous the results, that represents when the MER is approximately 18 dB that is suitable for received signal normally and few video error Therefore, the probability of cumulative distribution function (CDF) of received signal that shown in figure The frequency of 594 MHz can be given the MER is approximately 22 dB The frequency of 658 MHz can be given the MER is approximately 23 dB and The frequency of 722 MHz can be given the MER is approximately 18 dB That means the frequency of 722 MHz provide the MER for received signal is lower than other frequencies because the high frequency can be easily disturbed from environment than the low frequency Figure The comparison of MER and standard deviation of MER The standard deviation of MER represents the disturbance measurement in the MHz channel frequency bandwidth of DVB-T2 Figure shown when the standard deviation of MER is high will make the MER is low too, that means the error of data transmission has increased Figure The comparison of C/N, MER and standard deviation of MER at the frequency 658 MHz Figure shows the comparison between parameters of measurement There are C/N, MER and Standard deviation of MER This figure is a perspective of the evaluation signal analysis From the figure 9, this is the analysis of the frequency of 658 MHz that can be explained by when the C/N have high level therefore the MER will be high level as well The MER is the maximum level at approximately 30 dB, but even if the C/N have high level meanwhile the standard deviation of MER have high level too, that means the propagation of received signal is disturbed The standard of deviation is indicative of the noise of the receive channel has increased by the interference of environment Thus, the MER would have a low level The standard deviation of MER is the key variable that makes the MER has decreased and that represents the interference in the propagation channels REFERENCES [1] [2] [3] [4] V CONCLUSION This paper presents the performance evaluation of DVB-T2 for outdoor reception, which was conducted after the NBTC has set the appropriate parameter for broadcast the digital television in Thailand The signal analysis from this paper demonstrated the effect of C/N, MER and bBER from received signal by the different distance, locations and environment The frequencies of the transmitter for broadcasting represent the difference of frequencies have different effect and attenuation in the propagation channels The results of this study represents the efficiency signal of high frequency will be reduced by attenuation rather than the low frequency at the distance equally This study of signal analysis was measured in Bangkok metropolitan area In this city have tall buildings and dense urban areas This analysis provide information for outdoor reception characteristics therefore may not cover the measurement and analysis for rural area The area outside the Bangkok have the low noise and low interference, for this reason the results of this analysis could not covered the above mentioned The future research will analyze and evaluate the signal in areas outside the city and rural areas, which have not density of building and population However, for this research The results of the study could be useful for the improvement of DVB-T2 broadcast such as transmitter adjustment and gap filler transmitter installation to optimize the efficiency of digital television broadcasting View publication stats [5] [6] [7] [8] [9] Digital Video Broadcasting (DVB): Frame Structure Channel Coding and Modulation for a Second Generation Digital Terrestrial Television Broadcasting System (DVB-T2), ETSI Standard EN 302 755 V1.3.1, Apr.2012 Digital Video Broadcasting (DVB): Frame Structure Channel Coding and Modulation for Digital Terrestrial Television, ETSI Standard EN 300 744 V1.6.1, Jan 2009 Eizmendi, I ; Prieto, G ; Berjon-Eriz, G ; Landa, I ;Velez, M , “Empirical DVB-T2 Thresholds for Fixed Reception,” Broadcasting, IEEE Transactions on (Volume:59 , Issue: 2), pp 306 - 316, 13 March 2013 Berjon-Eriz,G ; Perez de Albeniz, I ; Eizmendi, I ; Prieto, G ; Velez,M., “DVB-T2 field trials results for portable indoor reception using T2-Lite and multiple PLP,” Broadband Multimedia Systems and Broadcasting (BMSB), 2013 IEEE International Symposium, pp 1-5, 5-7 June 2013 A Ingun, “DVB-T2 field trial and optimized parameters in Thailand,” in Electrical Engineering Congress (iEECON), 2014 International, pp 1-4, 19-21 March 2014 TR 101 290 V1.2.1 (2001-05) Digital Video Broadcasting (DVB); Measurement guidelines for DVB systems, Tech Report ETSI, 2001 Eizmendi,I ; Velez, M ; Gómez -Barquero, D ; Morgade, J ;BaenaLecuyer, V ; Slimani, M ; Zoellner, J , “DVB-T2: The Second Generation of Terrestrial Digital Video Broadcasting System”, Broadcasting, IEEE Transactions on (Volume:60 , Issue: 2), pp 258271, April 2014 Digital Video Broadcasting (DVB): Implementation Guidelines for a Second Generation Digital Terrestrial Television Broadcasting System (DVB-T2), ETSI Technical Specification TS 102 831 V1.1.1, Oct 2010 Morgade, J ; Angueira, P ; Arrinda, A ; Pfeffer, R ; Steinmann, V ; Frank, J ; Brugger, R., “SFN-SISO and SFN-MISO Gain Performance Analysis for DVB-T2 Network Planning”, Broadcasting, IEEE Transactions on (Volume:60 , Issue: 2), pp 272-286, January 2014 .. .Performance evaluation of DVB-T2 for outdoor reception Bundit Ruckveratham Sathaporn Promwong Department of Telecommunication Engineering, Faculty of Engineering King Mongkut’s Institute of. .. measurement performance of the portable reception [4] as well as the measurement for different location of urban and rural area However, few studies have reported on performance evaluation of DVB-T2. .. interleaving This paper provides the performance evaluation of DVB-T2 for outdoor reception by the received signal measurement The field measurements were taken in Bangkok of Thailand, along 50 locations