WIRELESS DOOR LOCK CONTROL SYSTEM MCL20,23,25 HỆ THỐNG ĐIỀU KHIỂN CỬA MCL20,23,25

WIRELESS DOOR LOCK CONTROL SYSTEM > OPERATION CHECK for Preparation Click here NOTICE WHEN CHECKING THE FOLLOWING a i ii iii Power door lock/unlock function: The wireless door lock control function operates only when the following conditions are met: No key is inserted in the ignition key cylinder All the doors are closed The power door lock system operates normally HINT: The unlock function operates even when a door is open b Power window open function: The wireless door lock control function operates only when the following conditions are met: i ii iii c No key is inserted in the ignition key cylinder Any door is unlocked The power window system operate normally Power window close function: The wireless remote control function operates only when the following conditions are satisfied i ii iii iv d No key is inserted into the ignition ley cylinder All the doors are closed All the doors are locked The power window system operates normally Power slide door and power back door open function: The wireless door lock control function operates only when the following conditions are met: i ii No key is inserted in the ignition key cylinder The power slide door or power back door main switch is ON (switch free: orange paint on the top of the switch appears) iii The slide door or back door is between the fully closed position and the half-open position (When the door is in the fully closed position, the door will be unlocked) iv The power slide door system and power back door system operates normally e Power slide door and power back door close function: The wireless door lock control function operates only when the following conditions are met: i ii iii iv No key is inserted in the ignition key cylinder The power slide door or power back door main switch is ON (switch free: orange paint on the top of the switch appears) The slide door or back door is between the half-open position and the fully open position The power slide door system and power back door system operates normally f Remote panic function: The wireless door lock control function operates only when the following condition is met: i The ignition switch is turned off HINT: The key can be inserted, however it must be in the off position g The wireless door lock control operational area differs depending on the situation i The operational area differs depending on the user and the ways the transmitter is held In certain areas, the remote control function will only operate partially for the operational area, which will be reduced due to the vehicle body shape and the influence of the surrounding environment Since the transmitter uses faint radio waves, strong radio waves or noise in the frequency used by the transmitter may reduce the operational area and the remote control may not function When the battery is weakened, the operational area is reduced and the remote control may not function ii iii iv HINT: If the door control transmitter has been left in a place that is exposed to direct sunlight, such as on the instrument panel, it may cause the battery to be weakened or cause other related problems CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS HINT: • • The switch described in this text is a switch for transmitting signals This switch is built into the door control transmitter All the functions listed below must be checked in comparison with the remote control operational area a Make sure that the vehicle is placed in conditions that allow the wireless control function to be operated b Check basic functions i Check whether the LED of the transmitter comes on times when each switch is pressed times HINT: If the LED does not come on when the switch has been pressed times or more, it may have a dead battery ii iii iv v Check that all the doors lock when LOCK is pressed Check that only the driver side door unlocks when UNLOCK is pressed once and that the other doors unlock when UNLOCK is pressed again within seconds Check that the power slide door opens or closes when the power slide door switch is held down for 0.8 seconds or more Check that the power slide door reverses right when the power slide door switch is pressed while the door is automatically moving (no delay) vi vii viii ix c i d i ii e i f i g Check that the power back door opens or closes when the power back door switch is held down for 0.8 seconds or more Check that the power door reverses right when the back door switch is pressed while the door is automatically moving (no delay) Check that all the power windows close when the LOCK switch is held down for 2.4 seconds and they stop operation when the switch is released (manual operation) Check that all the power windows open when the UNLOCK switch is held down for 2.4 seconds and they stop operation when the switch is released (manual operation) Check the chattering prevention function Check that the corresponding operation occurs only once and is not repeated continuously while the switch is held However, when the switch is operated repeatedly at second intervals, check that the corresponding operation is carried out Check the automatic locking function Check that the doors lock automatically as long as none of the doors have been opened or all the doors have not been locked within approximately 30 seconds after all the doors are unlocked by pressing the UNLOCK switch Check that the automatic locking function does not operate when any door has been opened or all the doors have been locked within approximately 30 seconds after all the doors are locked by pressing the UNLOCK switch Check the switch operation fail-safe function Check that the doors can not be locked by the switch while the key is in the ignition key cylinder However, this does not apply when the system is in the recognition code registration mode Check the operation stop function when a door is open or not completely closed Check that the doors are not locked by the switch while any door is open or not completely closed and the wireless door lock buzzer sounds for 10 seconds Check the repeat function i Check that all the doors attempt to automatically lock once again second after the LOCK switch has been pressed while the movement of the driver side door control knob, which is in the unlocked state, is being restricted h Check the hazard warning lights flashing and warning buzzer sounding functions (answer-back) i ii iii iv v When the LOCK switch is pressed, check that the lights flash once and the buzzer sounds once, simultaneously with the locking operation of all the doors When the UNLOCK switch is pressed once, check that the lights flash twice and the buzzer sounds twice, simultaneously with the unlocking operation of the driver side door When the UNLOCK switch is pressed again within seconds, check that the lights flash twice and the buzzer sounds twice, simultaneously with the unlocking operation of all the doors When the LOCK switch is held down 2.4 seconds, check that the buzzer sounds once and all the power windows start closing operation When the UNLOCK switch is held down for 2.4 seconds, check that the buzzer sounds once and all the power windows start opening operation vi When the power back door switch is held down for 0.8 seconds or more, check that the lights flash twice and the buzzer sounds twice, simultaneously with the operation of the power back door Check the remote panic function i i Check that the horn sounds, the headlights and taillights flash and the interior light remains on (when the light switch is turned to the DOOR position) for 60 seconds by the theft alarm function, when the PANIC switch is held down for 0.8 seconds or more Also, check that the horn stops sounding and the lights stop flashing when either switch of the transmitter is pressed WIRELESS DOOR LOCK CONTROL SYSTEM > REGISTRATION for Preparation Click here HINT: • • • • • • Register the recognition code when replacing the door control transmitter or the door control receiver Add mode is used to register new recognition codes while still retaining codes already registered This mode is used when a new transmitter is added If the number of registered codes exceeds 4, the previously registered codes will be erased in order, starting from the first registered code Rewrite mode is used to erase all the previously registered recognition codes in order to register all-new recognition codes This mode is used when the transmitter or the door control receiver is replaced with a new one Confirmation mode is used to confirm how many recognition codes have already been registered before another recognition code is registered Prohibition mode is used to erase all the registered codes and disable the wireless door lock function This mode is used when the transmitter is lost All the following registration procedures must be performed in order PROCEDURE FOR REGISTRATION OF RECOGNITION CODE (MANUAL OPERATION:) a Ensure that the following conditions are met: i ii iii No key is in the ignition key cylinder Driver side door is open (Other doors are closed) Driver side door is unlocked b When the above conditions are met, perform the following: i Insert and remove the key from the ignition key cylinder twice HINT: Complete this step within seconds ii iii iv v Close and open the driver side door twice Insert and remove the key from the ignition key cylinder Close and open the driver side door twice Insert the key into the ignition key cylinder and close all doors HINT: Complete this step within 40 seconds vi Turn the ignition switch from LOCK to ON and back to the LOCK position at approximately second intervals according to the number of times shown below HINT: If the number of ON-LOCK operations of the ignition switch is 0, or or more, there will be no response (power door lock and unlock operation) to show which mode has been selected vii Remove the key from the ignition key cylinder HINT: Complete this step within 40 seconds viii The body ECU automatically performs the power door LOCK-UNLOCK operation within seconds after the mode has been selected and informs the technician of the selected mode using the following response patterns HINT: • • • c When the confirmation mode or prohibition mode has been selected, the registration procedure will be completed In the confirmation mode, when the LOCK-UNLOCK operation is performed twice, the number of registered recognition codes is In the confirmation mode, when codes are registered, the LOCK-UNLOCK operation is automatically performed times Registration of the door control transmitter i ii If the add mode or rewrite mode has been selected, press LOCK and UNLOCK on the transmitter simultaneously Press either of the switches on the door control transmitter again HINT: • • iii Switches must be pressed for at least second each time The second operation must be performed within seconds after the first operation A recognition code must be registered in the door control transmitter within 40 seconds after a selected mode is responded to The body ECU automatically performs the power door LOCK-UNLOCK operation within seconds after the switch on the door control transmitter is turned off, in order to indicate whether registration has been completed correctly or not HINT: If the LOCK-UNLOCK operation is performed twice, registration of the recognition code has failed Perform registration procedures from the beginning once again iv If registration is continued, the next recognition code must be registered in the door control transmitter within 40 seconds HINT: Up to four recognition codes can be registered d Completing the registration mode i The registration mode will cease when any of the following occurs: • • • 40 seconds or more have elapsed after a previous registration mode is input Any of the doors is opened The key is inserted into the ignition key cylinder e Perform the following after registration is completed i Perform the wireless door lock control operation check (Click here) HINT: If the wireless door lock control does not operate, perform the registration procedure again PROCESURE FOR REGISTRATION OF RECOGNITION CODE (USING INTELLIGENT TESTER) a Turn the ignition switch to the ON position b Select the add or rewrite mode according to the intelligent tester display c The number of registered codes is indicated d Registration of the door control transmitter i ii If the add mode or rewrite mode has been selected, press LOCK and UNLOCK on the transmitter simultaneously Press either of the switches on the door control transmitter again HINT: Switches must be pressed for at least second each time The second operation must be performed within seconds after the first operation iii The body ECU automatically performs the power door LOCK-UNLOCK operation after the switch on the door control transmitter is turned off, in order to indicate whether registration has been completed correctly or not HINT: If the LOCK-UNLOCK operation is performed twice, registration of the recognition code has failed Perform registration procedures from the beginning once again iv If registration is continued, the next recognition code must be registered in the door control transmitter within 40 seconds HINT: Up to four recognition codes can be registered e Completing the registration mode i • • • f The registration mode will cease when any of the following occurs: 40 seconds or more have elapsed after a previous registration mode is input The intelligent tester is used to order completion The intelligent tester is disconnected Perform the following after registration is completed i Perform the wireless door lock control operation check (Click here) HINT: If the wireless door lock control does not operate, perform the registration procedure again GSIC - Global Service Information Center Page of DOOR CONTROL TRANSMITTER MODULE (for TMC Made) > REGISTRATION for Preparation Click here REGISTER RECOGNITION CODES HINT: z z z z z z Recognition code registration is necessary when the door control transmitter or the door control receiver is replaced with a new one Add Mode is used to register new recognition codes while retaining the previously registered codes This mode is used when new transmitters are added If the number of registered codes exceeds 4, the previously registered codes will be erased in order, starting from the first registered code Rewrite Mode is used to erase all the previously registered recognition codes in order to register new recognition codes This mode is used when the transmitter or the door control receiver is replaced with a new one Confirmation Mode is used to confirm how many recognition codes have already been registered before any additional recognition codes are registered Prohibition Mode is used to erase all the registered codes and disable the wireless door lock function This mode is used when the transmitters are lost The registration procedure described on the following pages must be performed in order a Check that the following conditions are met z No key is in the ignition key cylinder z Only driver side door is open b Insert the key into the ignition key cylinder, and remove it twice within seconds c Perform the following operations within 40 seconds i Close and open the driver side door twice ii Insert the key into the ignition key cylinder, then remove it d Perform the following operations within 40 seconds i Close and open the driver side door twice ii Insert the key into the ignition key cylinder and close all doors e Perform the following operations within 40 seconds i Turn the ignition switch from LOCK to ON and back to LOCK to times at approximately second intervals to select a mode (see the table below) http://stic-web.bm.toyota.co.jp/SelectCar_d/xmlweb/RM00S0E/htmlweb/MANUAL.HTM 11/7/2006 GSIC - Global Service Information Center Page of HINT: If the number of ignition switch on(IG)-LOCK operations is 0, 4, or more, there will be no response (power DOOR LOCK and UNLOCK operation) to show which mode has been selected ii Remove the key from the ignition key cylinder f The main body ECU automatically performs power door LOCK-UNLOCK operations to indicate which mode has been selected http://stic-web.bm.toyota.co.jp/SelectCar_d/xmlweb/RM00S0E/htmlweb/MANUAL.HTM 11/7/2006 GSIC - Global Service Information Center Page of HINT: z In Confirmation Mode, LOCK-UNLOCK operation will occur once for each recognition code that has been registered For example, if recognition codes have been registered, the LOCK-UNLOCK operation will occur twice z In Confirmation Mode, if no recognition codes have been registered, LOCKUNLOCK operation will occur 11 times z If Confirmation Mode or Prohibition Mode is selected, the operation ends after the response to the selected mode is completed g Register a new recognition code (Add Mode or Rewrite Mode) in accordance with the following procedure i Within 45 seconds of Add Mode or Rewrite Mode being selected, press the LOCK and UNLOCK switches on the transmitter switch of the key simultaneously for 1.0 to 1.5 seconds Within seconds of moving your finger away from the switches, press either switch of the key for more than 1.0 second ii Within seconds of the transmitter switch being released, the LOCK-UNLOCK operation will be automatically performed once if the registration of the recognition code is correctly completed If the LOCK-UNLOCK operation is performed twice, the registration of the recognition code has failed, so perform the registration procedure from the beginning once again http://stic-web.bm.toyota.co.jp/SelectCar_d/xmlweb/RM00S0E/htmlweb/MANUAL.HTM 11/7/2006 GSIC - Global Service Information Center Page of h If multiple transmitters need to be registered, repeat the registration of a new recognition code procedure within 45 seconds of the previous registration i If any of the following conditions is met, the Registration Mode will end i The key is inserted into the ignition key cylinder ii Any doors are opened iii 45 seconds or more elapse after code registration j Registration of the recognition codes (Add Mode and Rewrite Mode) is completed http://stic-web.bm.toyota.co.jp/SelectCar_d/xmlweb/RM00S0E/htmlweb/MANUAL.HTM 11/7/2006 GSIC - Global Service Information Center Page of http://stic-web.bm.toyota.co.jp/SelectCar_d/xmlweb/RM00S0E/htmlweb/MANUAL.HTM 11/7/2006 ... iv v Check that all the doors lock when LOCK is pressed Check that only the driver side door unlocks when UNLOCK is pressed once and that the other doors unlock when UNLOCK is pressed again within... pressed WIRELESS DOOR LOCK CONTROL SYSTEM > REGISTRATION for Preparation Click here HINT: • • • • • • Register the recognition code when replacing the door control transmitter or the door control. .. following after registration is completed i Perform the wireless door lock control operation check (Click here) HINT: If the wireless door lock control does not operate, perform the registration procedure