Thông tin tài liệu
builtt bbuild SLABS SLABS Liteform Slabform Linear Simplex table ST50 table ST110 table Support structures for slabs Props T28 towers MP shoring structures MP high load capacity towers Omnimode Accessories and spare parts 18 32 40 48 54 62 70 76 82 86 96 Slabs_LITEFORM LITEFORM and the new reinforcement system for traditional slabs and slabs cast in place present the advantages of improving efficiency, reducing the assembly time and increasing safety on site Company | Projects | Products LITEFORM It is a security lightweight formwork for traditional and cast in site slabs, it has been designed with the purpose to increase safety on site, improve productivity and reduce slab implementation times The system is especially suited for residential construction with rafter and hollow block slabs but it is also suitable for monolithic concrete slab Safe (it is assembled from below), handy and easy to be assembled (aluminium panels are very light), modular and highly productive, LITEFORM is the reinforcement system for slabs ideal for small and medium-companies for any type of slabs Slabs_LITEFORM The use of the LITEFORM system increases the safety and tidiness on site Company | Projects | Products STRENGTHS SAFE d!#%& "*") "*' 2( $1* ")*1"# ))"% '> )))"% '?* " (%"))"% ' takes place from the bottom with no risk of falling from above* d * " (" 2!" )&! $1 "*,""$ * " (%" )*( $1"() #,) &#) * #$ $1 * " ( !0 or plywood slab for casting safely the monolithic slabs The clearance between stringers is only 85 mm d* " (%") +"$#$C) &)2( !"* * #,),#(0 $1) " '"+"$, * ,"*)2( !" d* " $ $"))$ (" 2!" ," 1 *# $ + 2 !#%&#$"$*) $ 2% $ 2%(" 2!" the assembly and disassembly times d * " %# 2 ( *' # * " )')*"% $ *) ") $")) *# " ))"% " #,) 1 productivity d, * * "2)"# & ',## &$" ) !!#( $1*#* " ") 1$>* "%#$# * !) ) a smooth finish d ",!!"))#( ") #,!("* $1%2 * & "1"#%"*( ") $) %& "$ $*2 * +",'?* " frames can be reinforced in longitudinal and transverse direction d * " )&"! )%$* $1 " # LITEFORM allows increasing the productivity of the site, recovering during the dismantling stage all the panels just after a few days from casting and leaving only the props for concrete consolidation With the material recovered, and with the addition of another set of props, it is possible to reinforce another portion of slab d* " 3" " $ (#& " !$"2* ." , * $'*'&"# &(#&)&(")"$*#$) *" d* "LITEFORM frames allow reaching any measure LIGHT MODULAR PRODUCTIVE LITEFORM * The EEC regulating accident prevention in the workplace establishes serious penalties for companies that not adopt safety systems The Liteform system has been designed to safeguard the personnel involved from any danger of falling from a height Slabs_LITEFORM CHARACTERISTICS Weight of LITEFORM falling head 5.3 kg It is suitable for monolithic slabs up to 26 cm thick (without lightening) and conventional brick slabs.The expected loads can change from 4.5 to 7.0 kN/m2 with values for single prop from to 15 kN It included the use of Class B or Class D props (according to EN 1065) It can be used with any type of Liteform shore head A special latch prevents accidental release of the head from the shore +"$ * " ) ." # * " (%"> * ) )2 ! "$* % $ % amount of props (1 every m2) to significantly reduce the material to be handled with respect to traditional reinforcements Weight of LITEFORM fixed head 2.0 kg LITEFORM SYSTEM WITH VERY FEW COMPONENTS AND REDUCED WEIGHT Aluminium frames cm Weight kg Aluminium infill panels cm Weight kg 200x100 19,0 bars 180x30 6,8 200x75 15,1 bars 150x30 5,8 200x50 9,8 bars 180x30 4,4 bars 150x20 3,8 *Class B steel props are recommended pursuant to EN1085 Standard Steel props cm* 180/300 load 13,33 – 30 kN 200/350 load 11,43 – 30 kN Weight kg 15 19 Company | Projects | Products Slabs_LITEFORM ASSEMBLY Before installation, the props must be reinforced with the related dismantling heads or fixed head It is sufficient to insert the head into the props the hooking device, prevents the accidental ejection and rotation of the head Reinforce the props with the related dismantling or fixed heads and place a first row of props by using the tripods (Fig 1) Position the frames on the heads (it is )2 ! "$*#$ '#$"#&"(*#(L?* ")&"! ##0 $1 #,)) " $)* * #$>, * #2*( )0# !! "$* ) && $1#2*# * " " (#%* "&(#&K 1=
Ngày đăng: 03/11/2019, 10:20
Xem thêm:
