— RELION® PROTECTION AND CONTROL 615 series Technical Manual Document ID: 1MRS756887 Issued: 2018-12-20 Revision: N Product version: 5.0 FP1 © Copyright 2018 ABB All rights reserved Copyright This document and parts thereof must not be reproduced or copied without written permission from ABB, and the contents thereof must not be imparted to a third party, nor used for any unauthorized purpose The software or hardware described in this document is furnished under a license and may be used, copied, or disclosed only in accordance with the terms of such license Trademarks ABB and Relion are registered trademarks of the ABB Group All other brand or product names mentioned in this document may be trademarks or registered trademarks of their respective holders Warranty Please inquire about the terms of warranty from your nearest ABB representative www.abb.com/relion Disclaimer The data, examples and diagrams in this manual are included solely for the concept or product description and are not to be deemed as a statement of guaranteed properties All persons responsible for applying the equipment addressed in this manual must satisfy themselves that each intended application is suitable and acceptable, including that any applicable safety or other operational requirements are complied with In particular, any risks in applications where a system failure and/or product failure would create a risk for harm to property or persons (including but not limited to personal injuries or death) shall be the sole responsibility of the person or entity applying the equipment, and those so responsible are hereby requested to ensure that all measures are taken to exclude or mitigate such risks This product has been designed to be connected and communicate data and information via a network interface which should be connected to a secure network It is the sole responsibility of the person or entity responsible for network administration to ensure a secure connection to the network and to take the necessary measures (such as, but not limited to, installation of firewalls, application of authentication measures, encryption of data, installation of anti virus programs, etc.) to protect the product and the network, its system and interface included, against any kind of security breaches, unauthorized access, interference, intrusion, leakage and/or theft of data or information ABB is not liable for any such damages and/or losses This document has been carefully checked by ABB but deviations cannot be completely ruled out In case any errors are detected, the reader is kindly requested to notify the manufacturer Other than under explicit contractual commitments, in no event shall ABB be responsible or liable for any loss or damage resulting from the use of this manual or the application of the equipment Conformity This product complies with the directive of the Council of the European Communities on the approximation of the laws of the Member States relating to electromagnetic compatibility (EMC Directive 2004/108/EC) and concerning electrical equipment for use within specified voltage limits (Low-voltage directive 2006/95/EC) This conformity is the result of tests conducted by ABB in accordance with the product standard EN 60255-26 for the EMC directive, and with the product standards EN 60255-1 and EN 60255-27 for the low voltage directive The product is designed in accordance with the international standards of the IEC 60255 series Table of contents Table of contents Section Introduction 33 This manual 33 Intended audience 33 Product documentation 34 Product documentation set 34 Document revision history 34 Related documentation 35 Symbols and conventions .35 Symbols .35 Document conventions 36 Functions, codes and symbols 36 Section 615 series overview 43 Overview 43 Product series version history 44 PCM600 and relay connectivity package version 47 Local HMI 47 Display .48 LEDs 49 Keypad 49 Web HMI 50 Authorization 51 Audit trail 52 Communication .54 Self-healing Ethernet ring 55 Ethernet redundancy 56 Process bus .58 Secure communication 60 Section Basic functions 61 General parameters 61 Self-supervision 72 Internal faults 72 Warnings 75 LED indication control .76 Function block 76 Functionality 77 Programmable LEDs 77 Function block 77 Functionality 77 615 series Technical Manual Table of contents Signals .80 Settings 82 Monitored data 83 Time synchronization 84 Time master supervision GNRLLTMS .84 Function block 84 Functionality 84 Signals 86 Settings 86 Parameter setting groups 88 Function block 88 Functionality 88 Test mode .90 Function blocks 90 Functionality 90 Application configuration and Test mode 91 Control mode 91 Application configuration and Control mode 91 Authorization 92 LHMI indications 92 Signals .92 Fault recorder FLTRFRC 93 Function block 93 Functionality 94 Settings 94 Monitored data 95 Nonvolatile memory 103 Sensor inputs for currents and voltages 103 Binary input 105 Binary input filter time 105 Binary input inversion 106 Oscillation suppression 107 Binary outputs .107 Power output contacts 108 Dual single-pole power outputs PO1 and PO2 108 Double-pole power outputs PO3 and PO4 with trip circuit supervision 109 Dual single-pole high-speed power outputs HSO1, HSO2 and HSO3 109 Signal output contacts 110 Internal fault signal output IRF 110 Signal outputs SO1 and SO2 in power supply module 111 Signal outputs SO1, SO2, SO3 and SO4 in BIO0005 111 Signal outputs SO1, SO2 and SO3 in BIO0006 112 615 series Technical Manual Table of contents RTD/mA inputs 113 Functionality 113 Operation principle 113 Selection of input signal type 113 Selection of output value format 114 Input linear scaling 114 Measurement chain supervision 115 Self-supervision 115 Calibration 116 Limit value supervision 116 Deadband supervision 117 RTD temperature vs resistance 118 RTD/mA input connection 119 RTD/mA card variants 120 Signals .124 Settings 125 Monitored data 126 SMV function blocks 127 IEC 61850-9-2 LE sampled values sending SMVSENDER 127 Functionality 127 Settings 128 IEC 61850-9-2 LE sampled values receiving SMVRCV 128 Function block 128 Functionality 128 Signals 128 ULTVTR function block 128 Function block 128 Functionality 129 Operation principle 129 Signals 130 Settings 130 Monitored data 131 RESTVTR function block 131 Function block 131 Functionality 131 Operation principle 131 Signals 132 Settings 132 Monitored data 132 GOOSE function blocks 132 GOOSERCV_BIN function block 133 Function block 133 Functionality 133 615 series Technical Manual Table of contents Signals 133 GOOSERCV_DP function block 134 Function block 134 Functionality 134 Signals 134 GOOSERCV_MV function block 134 Function block 134 Functionality 134 Signals 134 GOOSERCV_INT8 function block 135 Function block 135 Functionality 135 Signals 135 GOOSERCV_INTL function block 135 Function block 135 Functionality 135 Signals 136 GOOSERCV_CMV function block 136 Function block 136 Functionality 136 Signals 136 GOOSERCV_ENUM function block 137 Function block 137 Functionality 137 Signals 137 GOOSERCV_INT32 function block 137 Function block 137 Functionality 137 Signals 137 Type conversion function blocks 138 QTY_GOOD function block 138 Function block 138 Functionality 138 Signals 138 QTY_BAD function block 139 Function block 139 Functionality 139 Signals 139 QTY_GOOSE_COMM function block 139 Function block 139 Functionality 140 Signals 140 T_HEALTH function block 140 615 series Technical Manual ... 615 Monitored data 615 Technical data 615 Technical revision history 616 Negative-sequence overvoltage protection NSPTOV 616 Identification 616 615 series Technical. .. 269 Technical data 270 Technical revision history 270 Three-phase thermal overload protection, two time constants T2PTTR 270 615 series Technical Manual Table... 299 Settings 300 Monitored data 301 Technical data 301 Technical revision history 301 615 series Technical Manual Table of contents Earth-fault protection