1. Trang chủ
  2. » Kỹ Thuật - Công Nghệ

Bakers pride eel oven PX 14 bếp nướng mặt trên

24 211 0

Đang tải... (xem toàn văn)

Tài liệu hạn chế xem trước, để xem đầy đủ mời bạn chọn Tải xuống

THÔNG TIN TÀI LIỆU

Thông tin cơ bản

Định dạng
Số trang 24
Dung lượng 2,95 MB

Nội dung

bản catalog gốc của nhà máy . dựa vào tài liệu các bạn có thể lấy số liệu cho bản vẽ thiết kế bếp ăn công nghiệp . ngoài ra còn có các bản vẽ chi tiết cấu tạo , chi tiết mạch điện . dành cho các kỹ thuật viên sử chữa. vì là bản gốc cho lên có thết sử dụng làm hướng đẫn sử dụng và làm đanh sách mua vật tư sửa chữa. bếp công nghiệp và các thiết bị sửa đụng trong đó là một vấn đề lớn cho các kỹ thật viên thiết kế bởi vì thế tài liệu này rất cần thiết cho các bạn .

INSTALLATION AND OPERATING INSTRUCTIONS COUNTER TOP ELECTRIC OVENS INTENDED FOR OTHER THAN HOUSEHOLD USE Models: PX-14, PX-16, P-18, BK-18, P-22S, P-22BL, P-24S, P-44S, P-44BL, P-46S, P-48S, DP-2 RETAIN THIS MANUAL FOR FUTURE REFERENCE OVEN MUST BE KEPT CLEAR OF COMBUSTIBLES AT ALL TIMES ! FOR YOUR SAFETY: Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance ! ! WARNING: Improper installation, adjustment, alteration, service or maintenance can cause property damage, injury or death Read the Installation, Operating and Maintenance Instructions thoroughly before installing or servicing this equipment Initial heating of oven may generate smoke or fumes and must be done in a well ventilated area Overexposure to smoke or fumes may cause nausea or dizziness ! Note: Only Pizza or Bread can have direct contact with ceramic decks All other food products must be placed in a pan or container to avoid direct contact with ceramic decks LA SSIFIE D C This equipment has been engineered to provide you with year round dependable service when used according to the instructions in this manual and standard commercial kitchen practices C P/N U4008A 1/08 BAKERS PRIDE OVEN CO., INC 30 Pine Street New Rochelle, NY 10801 (914) 576-0200 Phone (914) 576-0605 Fax (800) 431-2745 US & Canada www.bakerspride.com Web Address CONTENTS INSTALLATION INSTRUCTIONS SECTION ITEM Location Electrical Connections Requirements for Installation Initial Start Up PAGE 2 3 OPERATING INSTRUCTIONS SECTION ITEM General Baking General Baking Tips Special Features Cleaning Service and Trouble Shooting Installation of Decks PAGE 4 5 WIRING DIAGRAMS & SCHEMATICS ITEM PAGE P Series - Chamber - Ph, W or Ph, W (Wiring Diagram) P Series - Chamber - Ph, W - Star (Wiring Diagram) P Series - Chamber - Ph, W - Star (Wiring Diagram) P Series - Chamber - Ph, W or Ph, W (Wiring Diagram) 10 P Series Counter Top Ovens - Chamber (Schematic) 11 P Series Counter Top Ovens - Chamber (Schematic) 11 PX-14 & PX-16 (Wiring Diagram & Tables) 12 PARTS LISTS & WARRANTY ITEM PX -14, PX-16 (New Style) PX -14, PX-16 (Old Style) P18-S & BK18 P-22BL, P-22S & P-24S P-44S, P-44BL & P-48S DP-2 Warranty PAGE 13 14 15-16 17-18 19-20 21-22 23 IMPORTANT FOR FUTURE REFERENCE Please complete this information and retain this manual for the life of the equipment For Warranty Service and/or Parts, this information is required Model Number Serial Number Date Purchased INSTALLATION INSTRUCTIONS Minimum Clearance for Installation From combustible or non-combustible construction: Right side, Left side and Back: 3” (76mm) LOCATION Due to the heat a counter-top oven may produce, it must be placed on a non-combustible surface Do not store combustible materials on top of any oven ELECTRICAL CONNECTIONS Suitable means, which will disconnect all ungrounded conductors of the circuit simultaneously, must be provided by the installer Make sure electrical supply corresponds with that specified on the rating plate located in the rear of the oven When installed, the unit must be connected by an earthing cable to all other units within the complete installation and thence to an independent earth connection Use copper conductors only, rated at 90° C If a line cord is used for the installation of the unit in Europe, it should be a minimum of H07RN-F type conforming to EN60 335-1 and/or local codes Use minimum conductor size as below: ! ! For models PX-14, PX-16, P-18, BK-18 and P-24S: 14 Gauge (1.5mm) for 220-240V, single phase supply For models P-22S, P-22BL, P-44S, P-44BL, P-46S, P-48S and DP-2: 10 Gauge (2.5mm) for 220-240/380-415V, phase supply REQUIREMENTS FOR INSTALLATION For portable units (Model PX-14 and PX-16) there are no special requirements For shipping purposes the optional 4” (100mm) legs are not mounted For mounting legs, follow steps a through g a b c d e f g Remove the outer shipping carton and paper and place the oven on the floor or other flat surface Remove legs, baking decks and any other materials from inside the unit With sufficient help, tilt the unit back far enough to mount the two front legs and tighten with an adjustable wrench After the front legs are tight, lift rear of unit approximately 5” (125mm) off the surface and block in position using wood or some other solid material Now mount the two rear legs and tighten Using the proper lifting equipment, move the unit to its final location Adjust the bottom portion of legs to make level Slide baking decks into each shelf (View on Page 7) INITIAL START UP After the electrical connections have been made, the oven will need approximately to hours to burn off Initial heating of the oven may generate smoke or fumes and must be done in a well ventilated area CAUTION: OVEREXPOSURE TO SMOKE OR FUMES MAY CAUSE NAUSEA AND DIZZINESS For initial heating of the new oven, follow the steps below: ! ! ! ! Place the oven in a well ventilated area Open the oven doors and remove any instructions or samples shipped within the unit Make sure the oven cavity is empty and the baking decks are properly installed With the oven doors open, turn the temperature knobs to 400° F (205° C) for one hour Close the oven door Increase the temperature to 500° F (260° C) for at least ½ hours This procedure will dry out the insulation and deck material and will help to insure optimum baking results thereafter OPERATING INSTRUCTIONS Note: Only Pizza or Bread can have direct contact with ceramic decks All other food products must be placed in a pan or container to avoid direct contact with ceramic decks GENERAL BAKING Models: P-18, BK-18, P-22S, P-22BL, P-24S, P-44S, P-44BL, P-46S, P-48S, PX-14 and PX-16 Preheat the oven by setting the thermostat to the desired temperature When the thermostat light goes out and has cycled three times, the oven is ready for use These ovens have been designed to bake both fresh and frozen products Frozen fruit pies should be taken directly from the freezer and placed into the oven Cooking time will vary with the size of the pie, but under normal conditions a frozen pie should bake approximately in the same time as a fresh pie These ovens work well for toasting, melting cheese, baking frozen entrees, roasting small meat items, etc The temperature range for pizza baking is usually between 500° F (260° C) and 575° F (300° C) depending on the individual product Allow the pizza to bake until the cheese bubbles and the bottoms are evenly brown (Rotate if necessary) The design of the PX-14 and PX-16 is such that normal baking temperature may be too high for good results Set the thermostat approximately 25° F (15° C) BELOW normal setting Adjust temperature as needed Do not keep the oven door open too long when loading since heat will escape, resulting in slower baking When production requirements are low, keep the temperature low to prevent the bottoms from burning As demand increases, temperature should be raised for faster recovery Fresh dough generally requires a slightly lower baking temperature and longer bake time than defrosted pre-baked crusts GENERAL BAKING TIPS ! ! ! ! ! ! ! ! ! Pizza crusts should be fully defrosted before baking Wet areas on the bottom of a pizza will cause them to stick to the deck Avoid spills For fresh dough pizza, flour or corn meal on the peel will prevent sticking and ease placement of the pizza on the deck Increasing bake temperature during heavy production assists in maintaining temperature After the rush is over, reduce temperature to prevent burning Heavily topped pizzas require longer bake times at lower temperatures Placing a screen under pizza will allow the top to cook without overcooking the bottom Frequently scrape and brush off decks to remove burned residue which can cause an off flavor to the product Residue build-up can slow bake times A deck scraper/brush specifically designed for this is available from BAKERS PRIDE Clean heavily soiled pizza decks by scraping down, brushing off, removing from oven, turning over and putting back This procedure will burn off the decks and should be repeated every six months DO NOT USE WATER TO CLEAN THE DECKS as this could cause the decks to crack Using shiny pans or screens will produce products with light bottom color We strongly suggest that all pans and screens be seasoned before use SPECIAL FEATURES Timer: An electric timer is provided to give an audible, continuous signal at the end of a preset time up to 15 minutes (18 minutes with 50Hz supply) on pizza ovens, or 60 minutes (72 minutes with 50Hz supply) on bake ovens, Optional Electronic Timer: A Digital electronic 99 minute timer can be provided on all models to give an audible signal at the end of a pre-set time Note: TIMER DOES NOT CONTROL THE OVEN For PX-14 and PX-16 only: Individual switches are provided to turn off the top or the bottom heating element This allows baking items that not require direct top or bottom heat For DP-2 only: Optional infinite control switches can be provided for fine balancing of top and bottom heat CLEANING Periodic cleaning is suggested to keep your oven in good shape ALWAYS CLEAN THE OVEN WHEN IT IS COLD WHEN CLEANING STAINLESS STEEL, ALWAYS WIPE IN THE DIRECTION OF THE GRAIN Scrapers, brushes and stainless steel cleaner can be ordered from BAKERS PRIDE for this purpose From time to time the spillage should be scraped out For hard to clean spillage, the following is suggested: ! ! ! Turn the thermostat up to the highest setting and let the oven run for ½ hour with the door closed Allow the oven to cool down Brush the residue from deck Note: DO NOT USE WATER TO CLEAN DECKS CRACKING MAY RESULT Stainless steel surfaces should be cleaned with BAKERS PRIDE STAINLESS STEEL CLEANER SERVICE AND TROUBLE SHOOTING The ovens are designed to be as trouble free as possible Keeping the oven clean is all that is normally required All servicing should be performed by a factory authorized technician only However, if your oven stops operating, please check the following: ! ! Power supply cord is plugged into the supply receptacle Power supply fuse/circuit breaker has not tripped If the oven still does not operate, take the following steps: ! ! Disconnect the power supply to the unit by removing the supply cord and/or turning off the main switch Contact the factory, factory representative or an authorized service agency Note: Infinite control switches must be in a set position (other than off) in model DP-2 with optional infinite switches, for elements to operate A system wiring diagram is a part of this manual and is provided on the back of the unit For further information and to purchase the deck scraper/brush, or stainless steel cleaner, call BAKERS PRIDE at: (914) 576-0200 TROUBLESHOOTING CHART PROBLEM PROBABLE CAUSE SOLUTION Indicator light is out Set temperature has been reached Take no action The thermostat has turned off the power to the heat control switches, indicator lamps, contactors and heating elements When oven starts to cool, all functions will be restored Turn switches to a position other than "OFF" This will allow indicator lamps, contactors and heating elements to operate Replace fuse or reset circuit breaker The infinite top and bottom heat control switches are "OFF" (DP-2 w/Infinite Switches only) No power Oven too Hot Power supply fuses or circuit breakers are blown or have been tripped Power cord is unplugged Power supply fuses or circuit breakers are blown or have been tripped Power cord is unplugged Thermostat set too high Thermostat may be defective Bottom of pies are undercooked Bottom of pies burn before toppings are cooked Pies cook unevenly Bottom infinite switch set too low (DP-2 w/Infinite Switches only) Top Infinite switch set too high (DP-2 w/Infinite Switches only) Deck temperature too hot especially during slow periods Bottom infinite switch set too high (DP-2 w/Infinite Switches only) Top Infinite switch set too low (DP-2 w/Infinite Switches only) Area's adjacent to oven walls are generally hotter Plug in power cord Replace fuse or reset circuit breaker Plug in power cord Lower the thermostat setting Allow ample time for heat to regulate Call local authorized Bakers Pride Service Agent Increase setting Decrease setting Reduce Thermostat setting by 50° - 75° below normal bake temperature When decks cool begin cooking and immediately increase the thermostat setting by 50° - 75° Decrease setting Increase setting Rotate pies (180°), once during each bake or keep to the center of oven INSTALLATION OF DECKS DECK DECK ELECTRICAL WIRING DIAGRAMS, SCHEMATICS AND TABLES P-SERIES CHAMBER - PH, W OR PH, W - ELECTRICAL WIRING DIAGRAM & TABLES L2 L3 WT11 WT22 OR 240V OR UC BK8 BK14 WT13 BR15 UPPER BAKE CHAMBER P48S 200 208 240 208 208 240 200 BUZZER TIMER 250V BK16 BR17 208 240 200 P44S 208 240 200 P44SH 208 240 BK18 BK18 230 200 208 230 200 208 230 200 208 230 200 THERMOSTAT EGO POLE BR3 BR1 BK2 WT22 WT11 CIRCUIT PILOT BREAKER LIGHT PILOT LIGHT BR7 BR5 WT24 BR17 BK18 ELECTRONIC TIMER 250V (OPT) BK4 CIRCUIT THERMOSTAT BREAKER EGO POLE BK4 BK2 BK14 WT22 WT11 WT13 BR3 BR1 ROBERTSHAW THERMOSTATS BK4 BR17 BK18 ELECTRONIC TIMER 250V (OPT) 22.0 AMP - W LIGHT USA L1 L1 CAN 6-30P 19.0 6-30P 6-30P 25.5 6-30P 34.6 L3 11.0 11.0 22.0 11.4 11.4 22.0 9.3 9.3 18.7 9.7 9.7 18.7 6-50P 15.7 15.7 18.7 16.2 16.2 18.7 25.3 25.3 21.5 26.1 26.1 21.5 24.3 24.3 20.7 25.0 25.0 20.7 32.1 6-50P 230 L2 18.0 18.0 21.5 18.6 18.6 21.5 17.3 17.3 20.7 17.9 17.9 20.7 36.0 36.8 34.6 35.4 31.3 L3 10.8 10.8 21.5 11.2 11.2 21.5 10.3 10.3 20.7 10.7 10.7 20.7 28.8 29.4 27.6 28.2 25.0 L2 12.6 12.6 25.3 13.0 13.0 25.3 12.1 12.1 24.3 12.5 12.5 24.3 22.3 6-30P 208 COIL LOCATION AMP - NO LIGHT 21.5 21.9 20.7 21.1 18.7 PHASE - WIRE PLUG & NO 25.3 25.7 24.3 24.7 39.8 40.6 38.2 39.0 6-50P 22.0 22.0 18.7 22.7 22.7 18.7 27.1 27.1 25.3 27.9 27.9 25.3 26.1 26.1 24.3 26.9 26.9 24.3 35.3 6-50P 6-50P 23.6 23.6 22.0 24.3 24.3 22.0 WATT PER HEATING COIL & TOTAL WATT PER UNIT DP2 P48S P46S P44S P44SH 1,075 - 1,075 1,075 1,075 UC - UPPER CTR 1,075 - 1,450 1,450 1,450 UB - UPPER BOTT 1,450 1,075 1,075 1,075 1,450 LT - LOWER TOP 1,075 - 1,075 - 1,075 1,075 LC - LOWER CTR 1,075 - 1,450 1,450 LB - LOWER BOTT 1,450 1,075 1,075 1,075 1,450 TOTAL NO LIGHT 5,050 4,300 5,750 7,200 7,950 TOTAL W LIGHT 5,080 4,330 5,795 7,260 8,010 UT - UPPER TOP BR3 AMPERE COILS NO L W L 200 200 P46S BK20 BR27 2, OR AS REQUIRED LIGHT SWITCH (OPT) BK16 VOLT A/C UNIT DP2 BK28 BK16 BR15 LIGHT SWITCH (OPT) MODEL UT 21 WT BK10 208V UPPER HEATING COILS BK2 BR1 WT 21 BK26 BR17 250V LAMPS (OPT) BR27 BR7 BR25 BK28 I PHASE - WIRE OR UB WT24 BR29 BR5 LC BUZZER TIMER 250V BK16 BR23 WT22 WT11 LT LOWER LB BAKE CHAMBER 200V TERMINAL BLOCK PHASE LOWER HEATING COILS BK2 BR1 BR23 BK10 TERMINAL BLOCK PHASE BK30 L1 L2 BR19 L1 DWG 1012-120 10/09/00 P-SERIES CHAMBER - PH, W - STAR - ELECTRICAL WIRING DIAGRAM & TABLES L1 N L2 BR1 BK2 WT 11 BUZZER WT13 UPPER BAKE CHAMBER BK16 BK28 UNIT COILS P46S P44S P44SH BK18 BK18 BR1 BK2 BR1 BK2 WT11 BL31 BK4 WT42 BK40 BR41 BL35 BK18 ELECTRONIC TIMER 250V (OPT) CIRCUIT PILOT BREAKER LIGHT BK12 BR37 WT24 L2 L3 N L1 L2 L3 N 22.0 - - - - - - 22.0 22.3 - - - - - - 22.3 9.3 0.0 12.6 3.3 9.7 0.0 12.6 2.9 230 230 230/400 230 230 230 230/400 230 18.7 - - - - - - 18.7 19.0 - - - - - - 19.0 9.3 0.0 9.3 - - - 9.7 0.0 9.3 0.4 230 230 25.0 - - - - - - 25.0 25.5 - - - - - - 25.5 230/400 230 230 230 230/400 230 230 230 230/400 230 COIL LOCATION BR1 PILOT LIGHT BK2 ROBERTSHAW THERMOSTATS OR AS REQUIRED CIRCUIT THERMOSTAT BREAKER EGO POLE BR39 BK8 WT13 9.3 6.3 9.3 3.0 9.9 6.3 9.3 3.6 31.3 - - - - - - 31.3 32.0 - - - - - - 32.0 9.3 12.6 9.3 3.3 10.0 12.6 9.3 3.3 BL35 BK18 ELECTRONIC TIMER 250V (OPT) 34.6 - - - - - - 34.6 35.3 - - - - - - 35.3 9.3 12.6 12.6 3.3 10.0 12.6 12.6 2.6 WATT PER HEATING COIL & TOTAL WATT PER UNIT DP2 P48S P46S P44S P44SH 1,075 - 1,075 - 1,075 1,075 1,075 UC - UPPER CTR 1,450 1,450 1,450 UB - UPPER BOTT 1,450 1,075 1,075 1,075 1,450 LT - LOWER TOP 1,075 - 1,075 - 1,075 - 1,075 1,075 LC - LOWER CTR 1,450 1,450 LB - LOWER BOTT 1,450 1,075 1,075 1,075 1,450 TOTAL NO LIGHT 5,050 4,300 5,750 7,200 7,950 TOTAL W LIGHT 5,080 4,330 5,795 7,260 8,010 UT - UPPER TOP THERMOSTAT EGO POLE L1 AMPERE - W LIGHT BL35 TIMER 250V LIGHT SWITCH (OPT) BK16 LIGHT SWITCH (OPT) UB BK20 BL34 BL52 BK16 BK 26 BL35 DP2 P48S UC BK8 (BL53) BL33 BL52 BL36 BL36 BK12 WT24 BR37 BUZZER TIMER 250V BK16 BL32 BL35 BK28 1) 3N AMPERE - NO LIGHT VOLT A/C UT 2, OR AS REQUIRED BL52 LB BL34,45,45 5,4 BL52 LC (230V 400V UPPER HEATING COILS (BL53) 4,4 LOWER HEATING COILS 250V LAMPS (OPT) BL BR1 BK2 WT11 TERMINAL BLOCK PHASE LT LOWER BAKE CHAMBER MODEL L3 TERMINAL BLOCK PHASE BR39 L1 BR54 N DWG 1012-124 10/11/00 P-SERIES CHAMBER - PH, W - STAR - ELECTRICAL WIRING DIAGRAM & TABLES L1 BR54 N N L2 L1 L3 BL52 BK28 BK 26 BUZZER TIMER 250V BK16 BK2 WT22 BR1 BK18 P18S BL35 P24S BL34 P22SH P22S LIGHT SWITCH (OPT) BK16 UNIT COILS 230 230 230/400 230 230 230 230/400 230 L3 7.4 - - - - - 0.0 3.7 3.7 N 7.4 0.0 L1 L2 L3 N 7.6 - - - - - - 7.6 0.2 3.7 0.2 3.7 12.4 - - - - - - 12.4 12.7 - - - - - - 12.7 3.7 4.3 4.3 0.6 3.7 4.7 4.3 1.0 230 9.3 - - - - - - 9.3 9.5 - - - - - - 9.5 230 4.7 0.0 4.8 0.2 230 230 230/400 230 230 230 230/400 230 BE - BOT ELEMENT 0.0 4.7 0.2 4.8 15.7 - - - - - - 15.7 16.0 - - - - - - 16.0 4.7 6.3 4.7 1.4 4.7 6.7 4.7 4.7 6.3 6.3 1.6 4.7 6.7 6.3 BK18 850 - P24S P22S P22SH 1,075 1,075 1,000 1,075 - 1,450 1,450 P18S 850 850 1,000 1,075 1,075 1,450 BR1 2,850 2,150 3,600 3,975 WT22 TOTAL W LIGHT 1,715 2,880 2,165 3,630 4,005 BK4 CIRCUIT BREAKER BR12 BR37 WT24 PILOT LIGHT BR1 ROBERTSHAW THERMOSTAT CIRCUIT BREAKER 2.0 WATT PER HEATING COIL & TOTAL WATT PER UNIT 1,700 BK2 2.0 17.3 - - - - - - 17.3 17.6 - - - - - - 17.6 TOTAL NO LIGHT BL31 BL35 BK18 ELECTRONIC TIMER 250V (OPT) L2 230 TE - TOP ELEMENT L1 AMPERE - W LIGHT 230/400 COIL LOCATION BK18 THERMOSTAT EGO POLE AMPERE - NO LIGHT VOLT A/C BL32 BL36 BK12 BR37 BE BL31,32,34 BL52 CE (BL53) 2,3 1) 3N MODEL 250V LAMPS (OPT) OR AS REQUIRED 1,3 HEATING COILS TE (230V 400V TERMINAL BLOCK PHASE WT24 BL BR1 BK2 WT22 TERMINAL BLOCK PHASE DWG 1012-128 10/11/00 P-SERIES CHAMBER - PH, W or PH, W - ELECTRICAL WIRING DIAGRAM & TABLES L2 L1 L3 L1 L2 (N) TERMINAL BLOCK PHASE TERMINAL BLOCK PHASE VOLT A/C CE WT22 COILS 100 120 100 L3 AMP - W LIGHT L1 L2 L3 AMPERE NO L W L 17.0 17.4 USA CAN JAPAN 14.2 14.5 5-15P 5-20P 5-20P 6-15P 6-15P 6-15P 5-15P 5-20P 5-20P 6-15P 6-20P 6-15P BS 1363A CEE 7-VII 6-15P 6-15P 6-15P BS 1363A CEE 7-VII 8.5 0.0 8.5 8.7 0.2 8.5 208 8.2 0.0 8.2 8.4 0.2 8.2 8.5 8.2 8.7 8.4 230 8.1 0.0 8.1 8.2 0.1 8.1 8.1 8.2 100 120 100 18.0 18.8 120 200 14.3 208 13.7 15.0 N/A 250V LAMPS (OPT) OR AS REQUIRED BR27 WT24 BR7 BK28 BK26 BR17 208 240 BR15 200 P24S 208 240 200 P22S LIGHT SWITCH (OPT) BK16 208 240 200 208 240 BK18 BR3 THERMOSTAT EGO POLE BR1 BK2 WT24 9.3 14.7 5.4 9.3 4.8 8.9 14.1 5.2 8.9 14.3 14.7 13.7 14.1 230 13.5 200 10.8 208 10.3 4.7 8.8 13.9 5.1 230 10.2 200 18.0 208 17.3 8.8 13.5 13.9 0.0 10.8 11.0 0.2 10.8 0.0 10.3 10.5 0.2 10.3 10.8 11.0 10.3 10.5 0.0 10.2 10.4 0.2 10.2 10.2 10.4 7.2 10.8 18.4 7.7 10.8 7.0 10.3 17.7 7.4 10.3 18.0 18.4 17.3 17.7 230 17.1 200 19.9 208 19.1 6.9 10.2 17.4 7.2 10.2 17.1 17.4 7.2 12.6 20.3 7.7 12.6 7.0 12.1 19.5 7.4 12.1 19.9 20.3 19.1 19.5 230 18.8 6.9 12.0 19.2 7.2 12.0 18.8 19.2 UK N/A EUROPE N/A CEE 7-VII CIRCUIT BREAKER PILOT LIGHT CIRCUIT BREAKER BR3 BR1 BR7 BR5 BR3 BR1 BK16 TO SWITCH (OPT) WT22 WT24 ROBERTSHAW THERMOSTAT SINGLE POLE WITH SWITCH BK2 (WT22 NOT USED) ROBERTSHAW THERMOSTAT SINGLE POLE NO SWITCH PHASE ONLY A N/A 6-30P 6-20P 6-20P 6-20P 6-20P 6-30P 6-20P P18S-1 P18S-2 600 850 CE - CTR ELEMENT 850 - BE - BOT ELEMENT 850 600 600 TOTAL NO LIGHT 1,700 TOTAL W LIGHT 1,715 N/A N/A N/A N/A N/A WATT PER HEATING COIL & TOTAL WATT PER UNIT BK18 TE - TOP ELEMENT BK18 BR7 BR5 5.0 COIL LOCATION BR3 WT22 BR17 BK18 ELECTRONIC TIMER 250V (OPT) L2 208 240 200 P18S-2 P22SH AMP - NO LIGHT L1 120 200 200 P18S-1 BR25 BK16 UNIT PLUG CONFIGURATION & NUMBER BE BUZZER 10 TIMER 250V BK18 WT 21 BR29 TE BR5 1 OR OR OR OR BK2 BK10 BR1 WT22 BK10 BK2 BR1 100V 120V 200V 208V 230V 240V PH - W PHASE - WIRE MODEL HEATING COILS DWG 1012-127 10/9/00 P24S P22S P22SH 1,075 1,075 1,000 1,075 - 1,450 1,450 1,000 1,075 1,075 1,450 1,800 2,850 2,150 3,600 3,975 1,830 2,880 2,165 3,630 4,005 P-SERIES - CHAMBERS - ELECTRICAL WIRING SCHEMATICS DWG 1012-126 10/11/00 200V 208V 240V L1 1 L2 200V 208V 240V L1 3 UT UPPER CHAMBER L3 N 400V UT UC P UC TH UB UB TH UT TH L L LS L M B CB CB M B T CB LS LS LS L M M B T P P LT LC TH LB TH TH LT LT LC LC LB LB TH L2 (N) 200V 208V 240V L1 L L CB LS CB TH L2 L3 L1 B L CB B T LS CB T P TE TE TE CE CE CE BE BE BE TH TH LEGEND N, L1, L2, L3 = FROM TERMINAL BLOCK TH = THERMOSTAT POLE (3 POLE) P = THERMOSTAT INDICATOR LIGHT CB = CIRCUIT BREAKER M = SYNCHRONOUS TIMER (OR TIMER MOTOR) T = INTERVAL TIMER CONTACTS (IF PROVIDED) B = BUZZER (IF PROVIDED) LS = LIGHT SWITCH DPST ON-OFF (IF PROVIDED) L = INTERIOR LIGHTS (IF PROVIDED) L3 M CB P TH L2 L M T 3N N LS L CB P TH 400V 3 M B TH DWG 1012-129 10/11/00 L LS TH HEATER COILS UT = UPPER CHAMBER, TOP ELEMENT UC = UPPER CHAMBER, CENTER ELEMENT (P44 & P46 ONLY) UB = UPPER CHAMBER, BOTTOM ELEMENT LT = LOWER CHAMBER, TOP ELEMENT LC = LOWER CHAMBER, CENTER ELEMENT (P44 ONLY) LB = LOWER CHAMBER, BOTTOM ELEMENT P-SERIES - CHAMBER - ELECTRICAL WIRING SCHEMATICS 1 1 1 TH TH LEGEND N, L1, L2, L3 = FROM TERMINAL BLOCK TH = THERMOSTAT POLE (3 POLE) P = THERMOSTAT INDICATOR LIGHT CB = CIRCUIT BREAKER M = SYNCHRONOUS TIMER (OR TIMER MOTOR) T = INTERVAL TIMER CONTACTS (IF PROVIDED) B = BUZZER (IF PROVIDED) LS = LIGHT SWITCH DPST ON-OFF (IF PROVIDED) L = INTERIOR LIGHTS (IF PROVIDED) LS T P TH LS L M B T 100V 120V 200V 208V 230V 240V CB L L B L1 T CB CB L L LS L M B T TH L L LS LS TH UB TH LS L3 L2 TH UC TH TH LS L1 3N P P LOWER CHAMBER L2 TH HEATER COILS TE = TOP ELEMENT CE = CENTER ELEMENT (IF PROVIDED) BE = BOTTOM ELEMENT 11 TH TH TH PX-14 & PX-16 WIRING DIAGRAM & TABLES L1 Brn Blu Grn/Yel (Blk) (Wht) (Grn) -Line CordFor NEMA plugs see tables A4 er L2 (N) or: Blu-H1 E3 Gry Bottom Heating Coil S2 S1 Bottom Switch Pilot Light H3 Bottom Switch Top Switch A3 H1 Timer Motor Q1-Connector Q3-Butt Connector H5 H3 Q4-Twin Adapter Terminal 12 100/1 S2 Thermostat NEMA Plug Configuration & Number Europe Japan USA Canada UK Heating Coils Timer Motor Volts A/C Amp / Phase Watts / Volts Volts / Hz 750/100 15 200/1 120/60 100/1 120/60 120/1 15 5-15P 750/200 7.5 220-240/1 250/60 200/1 250/60 208-240/1 9.7 6-15P 750/220 BS 1363A CEE7-VII 900/100 125/60 900/100 125/60 900/200 250/60 900/220 250/60 900/220 250/60 5-20P 6-15P 8.1 Heating Coils Timer Motor Watts / Volts Volts / Hz 6-15P 750/220 6-15P H2 18 5-20P 8.1 nt me Ele m tto Bo NEMA Plug Configuration & Number Europe Japan USA Canada UK 6-15P 208-240/1 H1 5-15P 750/110 12.5 5-15P en t PX-16 5-15P 120/1 lem pE To Bottom Switch PX-14 Volts A/C Amp / Phase S1 Q5-Twin Adapter Terminal H5 Brn-A3 eC ord C1 To Top Switch Brn H3 NOTE: All wires to be 14 AWG 600V 200°C Color as shown above To T1 H1 E2 L in H4 Q2-Connector E3 Buz z Brn-T1 Q2-P1085A GND L1 A4 Q4 Brn-S2 A4 E3 Q5 er Q1-P1085A E2 Brn H5 Brn-S1 Top Heating Coil Blu-H2 Blu-H4 Top Switch L2 Terminal Block Timer Motor sta t P1069A E2 Gry C1 Blu Q3-Butt Connector Pilot Light L1 L2 (N) A1 H1 H2 C1 Buz z H1 T he rm o A1 Blu Gnd Terminal Block T1 A3 A1 H4 250/60 220-240/1 6-15P 9.7 BS 1363A CEE7-VII PARTS LISTS & EXPLODED VIEWS Electric Counter Top Oven (New Style) PX-14/16 PX-14 Beginning: Serial #4633, 12/09/99 (120V) or Serial #6547, 11/22/99 (208/240V) PX-16 Beginning: Serial #959, 11/11/99 (120V) or Serial #1783, 12/01/99 (208/240V) 18 17 30 29 28 27 26 25 10 11 13 16 19 21 MINUTES 15 14 13 12 11 10 650 300 600 550 350 500 20 23 22 24 13 12 Item Part # Description 10 11 12 13 14 15 16 17 18 D5023X D5123X S1153X M1335X P1003X D5027U D5127X U1308A U1309A M1383A M1384A M1119X S1311X M1037X S1038X P1127X D5038U D5138U Crumb Pan Assy w/Knob (PX-14) Crumb Pan Assy w/Knob (PX-16) Knob (Crumb Pan) Audio Alarm Terminal Block, Pole Control Panel Assy, Front (PX-14) Control Panel Assy, Front (PX-16) Control Panel Overlay, 60hz Control Panel Overlay, 50hz Timer, Electro-Mechanical, 15 Minutes, 120V Timer, Electro-Mechanical, 15 Minutes, 220V Thermostat, EGO, 300-650 deg (No Knob) Knob (Thermostat & Timer) Switch, Toggle, On/Off Rubber Boot, On/Off Switch (Export) Pilot Light, Amber Rear Panel Assy, (PX-14) Rear Panel Assy, (PX-16) 450 400 14 15 31 32 33 34 35 Item Part # Description 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 D5043U S1392A U1044X D5037U D5141U S1031X L1065X L1148X L1066X L1149X L1067X L1156X P6004X P6383A P6005X P6006X P6343X Capillary Retainer Assy Leg, each Bakers Pride Nameplate, 8" Peel Tray Assy w/Wire Rack & Hdl (PX-14) Peel Tray Assy w/Wire Rack & Hdl (PX-16) Handle, w/Nut & Bolt Element, PX-14, 120V/750W (2) Element, PX-16, 120V/900W (2) Element, PX-14, 220V/750W (2) Element, PX-16, 220V/900W (2) Element, PX-14, 100V/750W (2) Japan Element, PX-16, 200V/900W (2) Japan Line Cord, 125V/15A Line Cord, 125V/20A (Canada) Line Cord, 250V/15A Line Cord, CEE7-VII (Europe) Line Cord w/Fuse, 13A/240V (U.K.) Note: When ordering, ALWAYS specify Part #, Model #, Serial # and Voltage/Phase 13 10/05 Electric Counter Top Oven (Old Style) PX-14/16 PX-14 Before: Serial #4633, 12/09/99 (120V) or Serial #6547, 11/22/99 (208/240V) PX-16 Before: Serial #959, 11/11/99 (120V) or Serial #1783, 12/01/99 (208/240V) 28 27 26 25 24 23 14 17 15 16 19 MINUTES POINTER L’ETOILE, PUIS REGLER LE TEMPS 0 15 1 15 21 20 1414 5 1212 11 11 10 10 9 8 *4 1313 TURN POINTER TO STAR, THEN SET FOR TIME 650 300 600 650 550 600 500 550 22 Item Part # 33 32 31 30 29 11 10 400 450400 13 12 18 300 350 350 450 500 Description Item Part # Description D5023X Crumb Pan Assy w/Knob (PX-14) 18 S1392A Leg, each D5123X Crumb Pan Assy w/Knob (PX-16) 19 U1044X Bakers Pride Nameplate, 8" S1153X Knob (Crumb Pan) 20 D5037U Peel Tray Assy w/Wire Rack (PX-14) P1003X Terminal Block, Pole M1017X Timer, Mech, 15 Minutes (w/Knob/Plate) 21 D5141U Peel Tray Assy w/Wire Rack (PX-16) 22 S1031X Handle, w/Nut & Bolt S1052X Knob, Timer 23 L1065X Element, PX-14, 120V/750W (2) S1025X 24 L1148X Element, PX-16, 120V/900W (2) M1120X Plate, Timer Thermostat, EGO, 650F deg (w/Knob) 25 L1066X Element, PX-14, 220V/750W (2) M1119X Thermostat, EGO, 370C deg (w/Knob) 26 L1149X 10 S1155X Knob, Thermostat (650F) 27 L1067X Element, PX-16, 220V/900W (2) Element, PX-14, 100V/750W (2) Japan 11 S1154X Knob, Thermostat (370C) 28 L1156X Element, PX-16, 200V/900W (2) Japan 12 M1037X Switch, Toggle, On/Off 29 P6004X Line Cord, 125V/15A 13 S1038X Rubber Boot, On/Off Switch (Export) 30 P6383A Line Cord, 125V/20A (Canada) 14 P1127X Pilot Light, Amber 31 P6005X Line Cord, 250V/15A 15 D5038U Rear Panel Assy, (PX-14) 32 P6006X Line Cord, CEE7-VII (Europe) 16 D5138U Rear Panel Assy, (PX-16) 33 P6343X Line Cord w/Fuse, 13A/240V (U.K.) 17 D5043U Capillary Retainer Assy Note: When ordering, ALWAYS specify Part #, Model #, Serial # and Voltage/Phase 14 10/05 P18-S, BK18 Exterior/Door/Controls (Electro-Mechanical Timers) 29 30 31 32 13 26 36 14 15 16 17 18 19 25 37 23 24 35 MIN 28 0UT MIN ES UTES 300 650 12 UT MIN ES MIN UTES 27 20 21 22 300 650 BAKERS PRIDE 450 11 450 33 34 10 Item Part # Description 10 11 12 13 14 15 16 17 18 19 Thermostat w/Knob, EGO (Standard) P-18 20 Thermostat w/Knob, EGO (High Heat) P-18 21 Thermostat w/Knob, KA-72, 550deg (BK-18) 22 Knob (Thermostat & Timer) 23 Timer, Elec-Mech, 60 Min, 120V (BK-18) 24 Timer, Elec-Mech, 60 Min, 220V (BK-18) 25 Timer, Elec-Mech, 15 Min, 120V (P-18) 26 Timer, Elec-Mech, 15 Min, 220V (P-18) 27 Control Panel 28 Circuit Breaker, Amp 29 Audio Alarm (Discontinued) 30 Pilot Light, Amber 31 Terminal Block, Pole 32 Line Cord 125V/15A (US) P & BK 33 Line Cord 250V/15A (US & Japan) P & BK 34 Line Cord 125V/20A (Canada) 35 Line Cord 250V/20A (Canada) 36 Line Cord, 230V/16A "C" Type (CE) 37 Line Cord, 230V/13A (UK) N/S M1098X M1192X M1110X S1311X M1381A M1382A M1383A M1384A D3157K M1330A M1335X P1127X P1089A P6004X P6005X P6383X P6009X P6006X P6343X Item Part # U1302X U1307A U1314A U1297A U1296A S3019X D3106X S3001X Q3021X D3105K S1316U Q2041A U1044X S1014X S1014Y T3150A D3162U D3163U D2069X Description Control Panel Overlay, EGO (P-18) Control Panel Overlay, EGO Hi-Heat (P-18) Control Panel Overlay (BK-18) 18 Minute Timer Overlay (50 cycles) 72 Minute Timer Overlay (50 cycles) Bushing, Door Door Assy w/Handle Door Rod Door Rod Spacer Kit (1 Kit per Door) Outer Back Door Handle Assy, 10" Screw, 1/4-20 x 1/2 Rd Hd (Door Handle) Bakers Pride Nameplate, 8" 4" Adjustable Leg (Set/4) 4" Adjustable Leg (each) Intermediate Wire Rack (Option, BK18) Wire Rack Support Assy, Left (Option) Wire Rack Support Assy, Right (Option) Stacking Kit DECK ARRANGEMENT BY MODEL 1/4” ZA PIZ 1/4” MIN 1/2” UTES MIN KE UTES 300 650 300 650 BA BAKERS PRIDE BAKERS PRIDE 450 450 P18S BK18 Note: When ordering, ALWAYS specify Part #, Model #, Serial # and Voltage/Phase 15 10/05 P18, BK18 16 15 Interior Components & Accessories 12 12 17 17 11 11 10 10 9 22 1 20 20 13 13 33 21 21 66 4 1 24 24 18 18 22 22 19 19 88 Item Part # 66 Description Item 4 33 22 11 22 22 14 14 23 23 Part # Description L1024X Element 115V/600W (US/Can) P-18, T,C & B 13 K1355X Baffle & Top Elem Clips (5) BK L1171X Element 115V/850W (US/Can) BK-18, T & B 14 P1042A Element Clip, 5/16", Center & Bottom L1025X Element 208-240V/850W (US/Can/CE)P Top, BK T&B 15 T1120Y Ceramic Deck, 17 1/2 x 17 3/4 x 1/2 (each) L1026X Element 208-240V/1KW (US/Can/CE) P-18 C & B 16 T1120X Ceramic Deck, 17 1/2 x 17 3/4 x 1/2 (set/2) L1112X Element 200V/850W (Japan) P-18 Top 17 D3140Z Fresh Dough Baffle L1113X Element 200V/1000W (Japan) P-18 C & B 18 D3152T Hearth Frame Assy T5118X Steel Bake Deck (BK18 Only) 19 D4039K Deck Support T5107Y Deck Scraper Brush 20 D3151K Element Support P1019X Porcelain Spacer 21 D3131K Baffle Trim 10 Q3016A Washer, Star, #6 22 D3142K Deck Trim 11 Q1002A Nut, 6-32 23 D1134K Capillary Cover 12 S1061X 6-32 Terminal Cap 24 Q4021X Clip 3/16", Temp Sensor (2) Note: When ordering, ALWAYS specify Part #, Model #, Serial # and Voltage/Phase 16 10/05 P-22BL, P-22S, P-24S NEW STYLE EXTERIOR/DOOR/CONTROLS (Electro-Mechanical Timers) THIS PARTS LIST PERTAINS TO THE FOLLOWING UNITS: 31 33 32 16 15 37 26 28 38 38 34 34 13 MIN 17 18 19 UT MIN ES 300 650 MIN BAKERS PRIDE 450 24 23 450 Starting Serial # All #7131 #4160 #17288 25 39 35 36 12 Date N/A 11/2/99 11/2/99 2/29/00 20 21 22 UTES 300 650 Voltage All 208VAC 230VAC All 27 14 14 0UT MIN ES UTES 10 Model # P-22BL P-22S P-22S P-24S 30 29 CONTROL PANEL WITH DIGITAL TIMER (OPTIONAL) DIEHL micro 09 : 15 11 MIN - 20 21 22 300 650 SEC BAKERS PRIDE START-STOP + 450 14 12 DECK ARRANGEMENT BY MODEL 3/4” ZA PIZ 3/4” MIN 1/4” MIN 300 BAKERS PRIDE 450 P-22BL 10 11 12 13 14 15 16 17 18 19 20 M1098X M1192X M1110X M1342X S1311X M1384A M1382A M1275X M1274X D1157K D1156K M1330A M1335X P1127X P1003X P1004X P6009X P6385A P6005X U1302X BA 1/2” UTES 650 Item Part # ZA PIZ 1/4” UTES MIN UTES 300 650 300 650 KE BAKERS PRIDE BAKERS PRIDE 450 450 P-22S Description Thermostat w/Knob, 650F (EGO) Thermostat w/Knob, CE "430C" (High Heat) Thermostat w/Knob, 550F, KA-72 (P-24S) Thermostat Kit w/Knob, 250F (Special) Knob (T-stat "F", 15 Min Timer: Rot-Elec) Timer, Electro-Mech, 15 Min, (P-22S & P-22BL) Timer, Electro-Mech, 60 Min (P-24S) Timer, Electronic (Digital Readout) 60 cycle Timer, Electronic (Digital Readout) 50 cycle Control Panel (Rot/Elect Timer) Control Panel (Electronic Timer) Circuit Breaker, 3A Audio Alarm (Discontinued) Pilot Light, Amber Terminal Block, Pole, Phase Terminal Block, Pole, Phase Line Cord, 250V/20A (USA & Canada) Line Cord, 250V/30A (Can 208V only)P22S/BL Line Cord, 250V/15A (P-24S) Control Panel Overlay, 22S & 22BL P-24S Item Part # Description 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 U1307A U1314A U1297A U1296A S3019X D1106X S1020X D1143U S3001X Q3021X D1105K S1316U Q2041A U1044X S1014X S1014Y T3139X D1162U D1163U D2069X Control Panel Overlay, Hi Heat, 22S & 22BL Control Panel Overlay, P-24S 18 Minute Timer Overlay (50 cycle) 72 Minute Timer Overlay (50 cycle) Door Bushing Door Assy (No Window) Window Assy (Door) Door Assy (w/Window) Door Rod Door Rod Spacer Kit (1 Kit per Door) Outer Back Door Handle Screws, 1/4-20 x 1/2 RH (Door Handle) Bakers Pride Nameplate, 8" 4" Adjustable Leg (Set/4) 4" Adjustable Leg (each) Intermediate Wire Rack (Option, P-24) Wire Rack Support Assy, Left (Option) Wire Rack Support Assy, Right (Option) Stacking Kit Note: When ordering, ALWAYS specify Part #, Model #, Serial # and Voltage/Phase 17 10/05 P-22BL, P-22S, P-24S NEW STYLE Interior Components & Accessories 10 16 13 12 19 Brick Lined Models Only 22 17 20 18 23 15 14 11 20 21 24 Item Part # Description Item Part # Description L1072X L1071X Element, 208V/1075W, Top & Bottom Element, 208V/1450W, Center 13 T1120Y Deck, ea 17 3/4 x 17 1/2 x 1/2 (P-22BL Only) 14 T1121Y Deck, 20 13/16 x 20 13/16 x 1/2 (each) L1035X Element, 230V/1075W, Top & Bottom 15 T1121X Deck, 20 13/16 x 20 13/16 x 1/2 (set/2) L1034X Element, 230V/1450W, Center 16 D4040X Fresh Dough Baffle L1116X Element, 200V/1075W, Top & Bottom (Japan) 17 D1152T Hearth Frame Assy (No Element) L1117X Element, 200V/1450W, Center (Japan) 18 D4039K Deck Support P1019A Porcelain Spacer 19 D4031X Baffle Trim Q3016A Q1002A Washer, Star, #6 Nut, 6-32 20 21 D1142K D1134K Hearth Trim Capillary Cover 10 S1061X Terminal Cap, 6-32 22 Q4021X Clip, 3/16" 11 K1355X Element Clip 23 T1222K Steel Bake Deck (Optional) 12 D1158U Ceramic Top Frame Assy (B/L Only) 24 T5107Y Deck Scraper Brush Note: When ordering, ALWAYS specify Part #, Model #, Serial # and Voltage/Phase 18 10/05 P-44S, P-44BL, P-46S, P-48S EXTERIOR/DOOR/CONTROLS 35 NEW STYLE 28 31 18 17 41 29 38 Model # P-44BL P-44S P-44S P-46S P-48S Voltage All 208VAC 230VAC All All Starting Serial # All #9503 #6475 #17309 #17161 Date N/A 11/12/99 11/12/99 3/1/00 2/18/00 27 43 30 20 19 15 44 42 THIS PARTS LIST PERTAINS TO THE FOLLOWING UNITS: 36 37 32 (No Lights, Electro-Mechanical Timers) MIN 16 UTES 300 650 650 16 26 25 33 21 22 23 24 UTES 300 450 MIN 34 450 44 39 40 11 12 CONTROL PANEL WITH LIGHTS & DIGITAL TIMERS (OPTIONAL) 15 15 16 16 DIEHL micro 0 DIEHL micro 09 : 15 MIN 09 : 15 300 650 SEC 650 300 MIN START-STOP SEC START-STOP - + - 450 13 14 Item Part # Description 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 M1098X M1192X M1342X M1110X S1311X M1384A M1382A M1275X M1274X M1259X D2157K D2101K D2156K D2102K M1330A P1127X P1003X P1004X P6399A P6385A U1304A U1310A U1316A U1318A Thermostat w/Knob, 650F EGO, 44(2) 46(1) Thermostat w/Knob, CE "430C" High Heat 44 Thermostat Kit w/Knob, 250F (Special) Thermostat w/Knob, 550F KA72, 46 (1), 48 (2) Knob (T-stat "F", 15 Min Timer: Rot-Elec) Timer, Elec-Mech, 15 Min, 44(2) 46(1) Timer, Elec-Mech, 60 Min, 46(1) 48(2) Timer, Electronic (Digital Readout) 60 cycle Timer, Electronic (Digital Readout) 50 cycle Toggle Switch (Lights, On/Off) Control Panel (Rot/Elect Timer-No Lights) Control Panel (Rot/Elect Timer-w/Lights) Control Panel (Electronic Timer-No Lights) Control Panel (Electronic Timer-W/Lights) Circuit Breaker, 3A Pilot Light, Amber Terminal Block, Pole, Phase Terminal Block, Pole, Phase Line Cord, 125/250V, 50A Line Cord, 250V, 30A (P-46 & P-48) Control Panel Overlay (44 & 44BL) Control Panel Overlay, Hi Heat (44 & 44BL) Control Panel Overlay (P-46) Control Panel Overlay (P-48) + 450 10 16 Item Part # Description 25 26 27 28 29 30 31 U1297A U1296A S3019X D1106U S1020X D1143U P1145X P1129X P1147X P1020X P1122X S3001X Q3021X D2105K S1316U Q2041A U1044X S1014X S1014Y T3139A D1162U D1163U M1335A D2069X 18 Minute Timer Overlay (50 cycles) 72 Minute Timer Overlay (50 cycles) Door Bushing Door Assy (No Window) Window Assy (Door) Door Assy (w/Window) Light Fixture (w/240V,15W Bulb) Light Fixture (Old Style, 3” Diameter) Light Bulb, 240V/15W Light Bulb, (Old Style, 115V) Light Bulb, (Old Style, 250V) Door Rod Door Rod Spacer Kit (1 Kit per Door) Outer Back Door Handle Screws, 1/4-20 x 1/2 RH (Door Handle) Bakers Pride Nameplate, 8" 4" Adjustable Leg (Set/4) 4" Adjustable Leg (each) Intermediate Wire Rack (Option 46 & 48) Wire Rack Support Assy, Left (Option) Wire Rack Support Assy, Right (Option) Audio Alarm (Discontinued) Stacking Kit 32 33 34 35 36 37 38 39 40 41 42 43 44 45 Note: When ordering, ALWAYS specify Part #, Model #, Serial # and Voltage/Phase 19 21 22 23 24 10/05 P-44S, P-44BL, P-46S, P-48S NEW STYLE 23 15 12 Interior Components & Accessories 16 13 10 19 Brick Lined Models Only 14 22 17 20 24 18 11 20 21 DECK ARRANGEMENT BY MODEL 3/4” 3/4” 3/4” UTES 300 650 450 650 1/4” MIN UTES 300 P-44BL Item Part # 10 11 12 L1072X L1071X L1035X L1034X L1117X L1116X P1019A Q3016A Q1002A S1061X K1355X D1158U MIN UTES 1/4” ZA PIZ 1/4” 450 1/4” ZA PIZ 1/4” ZA PIZ 3/4” MIN 1/4” ZA PIZ 300 650 450 650 MIN UTES MIN 300 KE 7” BA 300 650 450 P-44S Description BA UTES 650 450 7” BA 7” KE ZA PIZ MIN UTES MIN UTES 450 P-46S 300 650 300 450 650 KE MIN UTES 300 450 P-48S Item Part # Description 13 14 15 16 17 18 19 20 21 22 23 24 T1120Y T1121Y T1121X D4040X D1152T D4039K D4031K D1142K D1134K Q4021X T1222K T5107Y Deck, ea 17 3/4 x 17 1/2 x 1/2 (P-44BL Only) Deck 20 13/16 x 20 13/16 x 1/2 (each) Deck 20 13/16 x 20 13/16 x 1/2 (Set/2) Fresh Dough Baffle Hearth Frame Assy (No Element) Deck Support Baffle Trim Hearth Trim Capillary Cover Clip, 3/16" Steel Deck (Optional) Deck Scraper Brush Element, 208V/1075W, Top & Bottom Element, 208V/1450W, Center Element, 230V/1075W, Top & Bottom Element, 230V/1450W, Center Element, 200V/1075W, Top & Bottom (Japan) Element, 200V/1450W, Center (Japan) Porcelain Spacer Washer, Star, #6 Nut, 6-32 Terminal Cap, 6-32 Element Clip Ceramic Top Frame Assy (P-44BL Only) Note: When ordering, ALWAYS specify Part #, Model #, Serial # and Voltage/Phase 20 10/05 DP-2 EXTERIOR / DOOR / CONTROLS (ELECTRO-MECHANICAL TIMERS) 27 NEW STYLE 26 32 15 23 MIN 14 UTES 18 300 650 650 450 19 20 UTES 300 14 15 MIN 24 450 25 17 16 THIS PARTS LIST PERTAINS TO THE FOLLOWING UNITS: Model # Starting Serial # Date DP-2 19062 5/25/00 30 31 33 34 28 29 11 12 14 CONTROL PANEL WITH DIGITAL TIMERS & INFINITE SWITCHES (OPTIONAL) 10 LOWER CHAMBER DIEHL micro 09 : 15 MIN SEC - + 650 650 300 22 15 Description M1098X M1192X S1311X M1384A M1275X M1274X M1335X M1259X M1367A M1368A S1205X D2101U D4046U D4045U M1330A P1127X P1003X P1004X Thermostat w/Knob, EGO T-stat w/Knob, CE "430C" (High Heat) Knob (Thermostat & Timer) Timer, Elec-Mech, 15 Min (220V) Timer, Electronic, 60Hz (Domestic) Timer, Electronic, 50Hz (CE) Audio Alarm (Discontinued) Toggle Switch (Lights, On/Off) Infinite Switch, 208V Infinite Switch, 240V Knob, Infinite Switch Control Panel (Rot-ElecTimer) Control Panel (Rot-ElecTimer/Infinite Sw.) Control Panel (ElectronicTimer/Infinite Sw.) Circuit Breaker, 3A Pilot Light, Amber Terminal Block, Pole (Domestic) Terminal Block, Pole (CE) 09 : 15 MIN SEC START-STOP - + UPPER CHAMBER 450 21 14 Part # 10 DIEHL micro 10 Item 10 11 12 13 14 15 16 17 300 450 9 10 15 10 START-STOP 0 10 14 20 19 13 Item Part # Description 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 N/S P6385A U1304A U1310A U1289A U1288A U1297A S3019X D4006X P1145X P1147X S3001X Q3021X S1316U Q2041A U1044X S1014Y S1014X D2069X Line Cord, 250V/30A Control Panel Overlay Control Panel Overlay (High-Heat) Overlay, Top Infinite Controls Overlay, Bottom Infinite Controls 18 Minute Timer Overlay (50 cycles) Door Bushing Door Assembly Light Fixture (w/240V, 15W Bulb) Light Bulb, 240V/15W Door Rod Door Rod Spacer Kit (1 Kit per Door) Door Handle Screws, 1/4-20 x 1/2 RH (Door Handle) Bakers Pride Nameplate, 8" 4" Adjustable Leg (each) 4" Adjustable Leg (Set/4) Stacking Kit Note: When ordering, ALWAYS specify Part #, Model #, Serial # and Voltage/Phase 21 10/05 DP-2 Interior Components NEW STYLE 10 14 17 19 15 15 18 18 12 13 Item Part # Description 10 L1072X L1071X L1034X L1035X L1117X L1116X P1019X Q3016A Q1002A S1061X Element, 208V/1075W, Top Element, 208V/1450W, Bottom Element, 230V/1075W, Top Element, 230V/1450W, Bottom Element, 200V/1075W, Top (Japan) Element, 200V/1450W, Bottom (Japan) Porcelain Spacer Washer, Star, #6 Nut, 6-32 Terminal Cap, 6-32 11 20 16 Item Part # Description 11 12 13 14 15 16 17 18 19 20 K1355X T1121Y T1121X D4040X D1152T D4039K D4031K D4034K Q4021X D1142K Element Clip Hearth Deck 20 13/16 x 20 13/16 x 1/2 (each) Hearth Deck 20 13/16 x 20 13/16 x 1/2 (Set/2) Fresh Dough Baffle Hearth Frame Assy Deck Support Baffle Trim Capillary Cover Clip, 3/16" (Capillary) Deck Trim Note: When ordering, ALWAYS specify Part #, Model #, Serial # and Voltage/Phase 22 10/05 BAKERS PRIDE LIMITED WARRANTY 30 Pine Street New Rochelle, New York 10801 914 / 576 - 0200 ♦ US & Canada: - 800 - 431 - 2745 ♦ fax 914 / 576 - 0605 WHAT IS COVERED This warranty covers defects in material and workmanship under normal use, and applies only to the original purchaser providing that: ♦ The equipment has not been accidentally or intentionally damaged, altered or misused; ♦ The equipment is properly installed, adjusted, operated and maintained in accordance with National and local codes and in accordance with the installation instruction provided with the product; ♦ The serial number rating plate affixed to the equipment has not been defaced or removed WHO IS COVERED This warranty is extended to the original purchaser and applies only to equipment purchased for use in the U.S.A COVERAGE PERIOD Full size gas and electric deck ovens: Two (2) year limited parts and labor: Cyclone Convection Ovens: BCO Models: One (1) Year limited parts and labor; GDCO Models: Two (2) Year limited parts and labor; CO II Models: Two (2) Year limited parts and labor; (5) Year limited door warranty All Other Products: One (1) Year limited parts and labor Warranty period begins the date of dealer invoice to customer or ninety (90) days after shipment date from BAKERS PRIDE whichever comes first WARRANTY COVERAGE This warranty covers on-site labor, parts and reasonable travel time and travel expenses of the authorized service representative up to (100) miles round trip, and (2) hours travel time The purchaser however, shall be responsible for all expenses related to travel, including time mileage and shipping expenses on smaller counter models that may be carried into a Factory Authorized Service Center, including the following models: PX-14 PX-16, PI8, and BK-I8 EXCEPTIONS All removable parts in BAKERS PRIDE Char-broilers, including but not limited to: Burners, Grates Radiants, Stones and Valves, are covered for a period of SIX MONTHS All Ceramic Baking Decks are covered for a period of THREE MONTHS The installation of these replacement decks is the responsibility of the purchaser The extended Cyclone door warranty years through is a parts only warranty and does not include labor, travel, milage or any other charges EXCLUSIONS ♦ Failures caused by erratic voltages or gas supplies, ♦ Unauthorized repair by anyone other than a BAKERS PRIDE Factory Authorized Service Center, ♦ Damage in shipment, ♦ Alteration, misuse or improper installation, ♦ Thermostats and safety valves with broken capillary tubes ♦ Accessories - spatulas, forks steak turners, grate lifters, oven brushes, scrapers, peels etc., ♦ Freight - other than normal UPS charges, ♦ Ordinary wear and tear ♦ Negligence or acts of God, ♦ Thermostat calibrations after (30) days from equipment installation date, ♦ Air and Gas adjustments, ♦ Light bulbs, ♦ Glass doors and door adjustments ♦ Fuses, ♦ Char-broiler work decks and cutting boards, ♦ Tightening of conveyor chains, ♦ Adjustments to burner flames and cleaning of pilot burners, ♦ Tightening of screws or fasteners INSTALLATION Leveling and installation of decks as well as proper installation and check out of all new equipment - per appropriate installation and use materials - is the responsibility of the dealer or installer, not the manufacturer REPLACEMENT PARTS BAKERS PRIDE genuine Factory OEM parts receive a (90) day materials warranty effective from the date of installation by a BAKERS PRIDE Factory Authorized Service Center This Warranty is in lieu of all other warranties, expressed or implied, and all other obligations or liabilities on the manufacturers part BAKERS PRIDE shall in no event be liable for any special, indirect or consequential damages, or in any event for damages in excess of the purchase price of the unit The repair or replacement of proven defective parts shall constitute a fulfillment of all obligations under the terms of this warranty Form #U4177A 1/07 23 BAKERS PRIDE OVEN CO., INC 30 Pine Street New Rochelle, NY 10801 (914) 576-0200 Phone (914) 576-0605 Fax (800) 431-2745 US & Canada www.bakerspride.com Web Address 24 ... Top Ovens - Chamber (Schematic) 11 P Series Counter Top Ovens - Chamber (Schematic) 11 PX- 14 & PX- 16 (Wiring Diagram & Tables) 12 PARTS LISTS & WARRANTY ITEM PX -14, PX- 16 (New Style) PX -14, PX- 16... w/Nut & Bolt Element, PX- 14, 120V/750W (2) Element, PX- 16, 120V/900W (2) Element, PX- 14, 220V/750W (2) Element, PX- 16, 220V/900W (2) Element, PX- 14, 100V/750W (2) Japan Element, PX- 16, 200V/900W (2)... L 1149 X L1067X L1156X P6004X P6383A P6005X P6006X P6343X Capillary Retainer Assy Leg, each Bakers Pride Nameplate, 8" Peel Tray Assy w/Wire Rack & Hdl (PX- 14) Peel Tray Assy w/Wire Rack & Hdl (PX- 16)

Ngày đăng: 12/03/2019, 19:01

TỪ KHÓA LIÊN QUAN

w