Automobile training 34 wiper washer

Automobile training 34 wiper washer Automobile training 34 wiper washer Automobile training 34 wiper washer Automobile training 34 wiper washer Automobile training 34 wiper washer Automobile training 34 wiper washer Automobile training 34 wiper washer Automobile training 34 wiper washer Automobile training 34 wiper washer Automobile training 34 wiper washer Automobile training 34 wiper washer Automobile training 34 wiper washer Automobile training 34 wiper washer Automobile training 34 wiper washer Automobile training 34 wiper washer Automobile training 34 wiper washer Automobile training 34 wiper washer Automobile training 34 wiper washer Automobile training 34 wiper washer Automobile training 34 wiper washer Automobile training 34 wiper washer

WIPER AND WASHER – WIPER AND WASHER SYSTEM WW–1 WIPER AND WASHER SYSTEM PRECAUTION WASHER NOZZLE ADJUSTMENT PRECAUTION (a) Do not clean or adjust the washer nozzle using objects such as needles or safety pins, because; (1) The washer nozzle tip is made of resin and could be damaged (2) Adjustment is not necessary as the washer nozzle is a spray type (b) If the washer nozzle is clogged with substances such as car wax, remove it and clean the nozzle hole with a soft resin brush or similar tool WW WW–2 WIPER AND WASHER – WIPER AND WASHER SYSTEM PARTS LOCATION REAR WASHER NOZZLE HACHBACK: FRONT WIPER MOTOR FRONT WASHER NOZZLE WW REAR WIPER MOTOR WASHER MOTOR WIPER SWITCH MAIN BODY ECU (INSTRUMENT PANEL J/B) - WIP FUSE - RR WIP FUSE - WSH FUSE E114278E04 WIPER AND WASHER – WIPER AND WASHER SYSTEM WW–3 SEDAN: WASHER NOZZLE WW WASHER MOTOR FRONT WIPER MOTOR WIPER SWITCH MAIN BODY ECU (INSTRUMENT PANEL J/B) - WIP FUSE - WSH FUSE B142259E01 WW–4 WIPER AND WASHER – WIPER AND WASHER SYSTEM SYSTEM DIAGRAM Front Wiper and Washer: WSH To Battery WIP To Battery Front Washer Motor Windshield Wiper Switch Assembly WW Front Washer Switch Front Wiper Switch +B +2 +1 +S INT1 INT2 WF B1 MIST OFF OFF ON EW INT LO HI +S +B +2 +1 +S +2 +1 +S INT1 INT2 B1 EW WF B Front Wiper Motor E114280E04 WIPER AND WASHER – WIPER AND WASHER SYSTEM WW–5 Rear Wiper and Washer: WSH To Battery RR WIP To Battery Rear Washer Motor WW Windshield Wiper Switch Assembly WR +IR EW Washer Rear Wiper and Washer Switch OFF ON ON + Washer B +1 Rear Wiper Motor E114281E07 WW–6 WIPER AND WASHER – WIPER AND WASHER SYSTEM PROBLEM SYMPTOMS TABLE HINT: Use the table below to help determine the causes of the problem symptom The potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table Check each symptom by checking the suspected areas in the order they are listed Replace parts as necessary Wiper and washer system Symptom Front wipers and washer system not operate Suspected area WIP fuse WW-2 WSH fuse WW-2 Windshield wiper switch assembly (for hatchback) WW-39 Windshield wiper switch assembly (for sedan) WW-35 Wire harness WW Front wipers not operate in LO or HI WW-2 Windshield wiper switch assembly (for hatchback) WW-39 Windshield wiper switch assembly (for sedan) WW-35 Front wiper motor (for hatchback) WW-19 Front wiper motor (for sedan) WW-11 WW-2 Windshield wiper switch assembly (for hatchback) WW-39 Windshield wiper switch assembly (for sedan) WW-35 Front wiper motor (for hatchback) WW-19 Front wiper motor (for sedan) WW-11 WW-2 Windshield wiper switch assembly (for hatchback) WW-39 Windshield wiper switch assembly (for sedan) WW-35 Front washer motor (for hatchback) WW-51 Front washer motor (for sedan) WW-45 Rear wiper and washer system not operate WW-2 Windshield wiper switch assembly (for hatchback) WW-39 Windshield wiper switch assembly (for sedan) WW-35 Front wiper motor (for hatchback) WW-19 Front wiper motor (for sedan) WW-11 - Front wiper motor (for hatchback) WW-19 Front wiper motor (for sedan) WW-11 Wire harness - RR WIP fuse WW-2 WSH fuse WW-2 Windshield wiper switch assembly WW-39 Wire harness Rear wiper motor does not operate - WIP fuse Wire harness Front wiper arms not return to their original positions when wiper switch turned off - WSH fuse Wire harness Front wipers not operate when washer switch on - WIP fuse Wire harness Front washer motor does not operate - WIP fuse Wire harness Front wipers not operate in INT See page - RR WIP fuse WW-2 Windshield wiper switch assembly WW-39 Rear wiper motor WW-29 Wire harness - WW–7 WIPER AND WASHER – WIPER AND WASHER SYSTEM Symptom Rear washer motor does not operate Suspected area WW-2 Windshield wiper switch assembly WW-39 Rear washer motor WW-51 Wire harness Rear wiper arm does not return to its original position when rear wiper switch turned off See page WSH fuse Rear wiper motor Wire harness WW-29 - WW WW–8 WIPER AND WASHER – FRONT WIPER MOTOR (for Sedan) FRONT WIPER MOTOR (for Sedan) BODY ELECTRICAL WIPER AND WASHER COMPONENTS FRONT WIPER ARM AND BLADE ASSEMBLY RH FRONT WIPER ARM HEAD CAP 26 (265, 19) FRONT WIPER ARM AND BLADE ASSEMBLY LH FRONT WIPER ARM HEAD CAP WW 26 (265, 19) COWL SIDE VENTILATOR SUB-ASSEMBLY RH COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY COWL SIDE VENTILATOR SUB-ASSEMBLY LH 5.4 (55, 48 in.*lbf) x3 5.5 (56, 49 in.*lbf) FRONT WIPER MOTOR AND LINK 5.5 (56, 49 in.*lbf) FRONT WIPER MOTOR N*m (kgf*cm, ft*lbf) : Specified torque E129678E02 WIPER AND WASHER – FRONT WIPER MOTOR (for Sedan) WW–9 ON-VEHICLE INSPECTION Mark for Blade Position INSPECT FRONT WIPER MOTOR (a) Check the automatic stop position (1) Operate the front wiper motor, then stop the operation (2) Check the automatic stop position when the front wiper motor operation has stopped Standard: Front wiper arm stops in the position shown in the illustration WW Mark for Blade Position E129693E01 WW–10 WIPER AND WASHER – FRONT WIPER MOTOR (for Sedan) REMOVAL Protective Tape Protective Tape DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL REMOVE FRONT WIPER ARM HEAD CAP (a) Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the front wiper arm head caps REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH (a) Operate the wiper, then stop the windshield wiper motor in the automatic stop position (b) Remove the nut and front wiper arm REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH HINT: Use the same procedure as for the LH side REMOVE COWL SIDE VENTILATOR SUB-ASSEMBLY LH (a) Using a screwdriver with its tip wrapped in protective tape, disengage the claws and remove the cowl side ventilator sub-assembly LH REMOVE COWL SIDE VENTILATOR SUB-ASSEMBLY RH HINT: Use the same procedure as for the LH side REMOVE COWL TOP VENTILATOR LOUVER SUBASSEMBLY (a) Disengage the clips, the claws and the hooks (b) Remove the cowl top ventilator louver subassembly WW E127832E01 E127833 Protective Tape E127834E01 E127838 WW–50 WIPER AND WASHER – WASHER MOTOR (for Hatchback) WW WINDSHIELD WASHER MOTOR AND PUMP ASSEMBLY (REAR SIDE) WINDSHIELD WASHER MOTOR AND PUMP ASSEMBLY (FRONT SIDE) E114481E01 WIPER AND WASHER – WASHER MOTOR (for Hatchback) WW–51 ON-VEHICLE INSPECTION E114464 E114465 INSPECT WINDSHIELD WASHER MOTOR AND PUMP ASSEMBLY (for Front Side) (a) Check the operation of the windshield washer motor and pump front side (1) Fill the washer jar with washer fluid HINT: The operation should be performed with the windshield washer motor and pump installed on the washer jar (2) Connect the positive (+) battery lead to terminal of the windshield washer motor and pump, and the negative (-) battery lead to terminal Check that washer fluid flows from the washer jar Standard: Washer fluid flows from the washer jar If the result is not as specified, replace the windshield washer motor and pump INSPECT REAR WASHER MOTOR AND PUMP ASSEMBLY (for Rear Side) (a) Check the operation of the windshield washer motor and pump rear side (1) Fill the washer jar with washer fluid HINT: The operation should be performed with the windshield washer motor and pump installed onto the washer jar (2) Connect the positive (+) battery lead to terminal of the windshield washer motor and pump, and the negative (-) battery lead to terminal Check that washer fluid flows from the washer jar Standard: Washer fluid flows from the washer jar If the result is not as specified, replace the rear washer motor and pump WW WW–52 WIPER AND WASHER – WASHER MOTOR (for Hatchback) REMOVAL DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL REMOVE FRONT BUMPER COVER (See page ET-24) REMOVE RH HEADLIGHT ASSEMBLY (See page LI97) DRAIN WASHER FLUID (a) Disconnect the washer hoses from the windshield washer motor and pump, and drain the washer fluid REMOVE WINDSHIELD WASHER JAR ASSEMBLY (a) Disconnect the harness clamps (b) Disconnect the connectors (c) Remove the bolts (d) Remove the windshield washer jar REMOVE WINDSHIELD WASHER MOTOR AND PUMP ASSEMBLY (a) Pull the washer motor and pump out of the packing of the washer jar WW E117644 E114467 INSTALLATION E114467 INSTALL WINDSHIELD WASHER MOTOR AND PUMP ASSEMBLY (a) Install the windshield washer motor and pump onto the packing of the washer jar WIPER AND WASHER – WASHER MOTOR (for Hatchback) WW–53 INSTALL WINDSHIELD WASHER JAR ASSEMBLY (a) Install the windshield washer jar E114468 (b) Install the bolts Torque: 5.5 N*m (56 kgf*cm, 49 in.*lbf) (c) Connect the connectors (d) Connect the harness clamps E117645 FILL UP WASHER JAR AND PUMP ASSEMBLY WITH WASHER FLUID (a) Connect the washer hose to the washer motor and pump, and fill the washer jar with washer fluid INSTALL RH HEADLIGHT ASSEMBLY (See page LI104) INSTALL FRONT BUMPER COVER (See page ET-33) CONNECT CABLE TO NEGATIVE BATTERY TERMINAL Torque: 5.4 N*m (55 kgf*cm, 48 in.*lbf) WW WW–54 WIPER AND WASHER – WASHER NOZZLE (for Sedan) WASHER NOZZLE (for Sedan) ON-VEHICLE INSPECTION INSPECT WASHER NOZZLE (a) Start the engine (b) Check where the washer fluid hits the windshield Standard: Washer fluid hits the windshield in the areas shown in the illustration WW B A Upper Point E C Standard Washer Fluid Contact Area Lower Point D G F E127795E01 Specification Area Measurement A 29.2 mm (1.15 in.) B 26.6 mm (1.05 in.) C 427.8 mm (16.84 in.) D 79.9 mm (3.15 in.) E 426.2 mm (16.78 in.) F 234.8 mm (9.24 in.) G 234.5 mm (9.23 in.) WW–55 WIPER AND WASHER – WASHER NOZZLE (for Sedan) ADJUSTMENT REMOVE FRONT WIPER ARM HEAD CAP (See page WW-9) REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH (See page WW-9) REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH (See page WW-9) REMOVE COWL SIDE VENTILATOR SUB-ASSEMBLY LH (See page WW-10) REMOVE COWL SIDE VENTILATOR SUB-ASSEMBLY RH (See page WW-10) REMOVE COWL TOP VENTILATOR LOUVER SUBASSEMBLY (See page WW-10) REMOVE WASHER NOZZLE (a) Disconnect the washer hose (b) Disengage the claws and remove the front washer nozzle NOTICE: Do not reuse the washer nozzle ADJUST WASHER NOZZLE (a) Select a washer nozzle from the table so as to make the washer fluid hit within the specified area Available Washer Nozzle E127796 Discrimination Number E108416E01 Washer Fluid Injection Angle Part Number Discrimination Number 85381-52250 12 0° 85381-52280 13 + 1° 85381-52290 11 - 1° 85381-52300 14 + 2° 85381-52310 10 - 2° INSTALL COWL TOP VENTILATOR LOUVER SUBASSEMBLY (See page WW-12) 10 INSTALL COWL SIDE VENTILATOR SUB-ASSEMBLY LH (See page WW-13) 11 INSTALL COWL SIDE VENTILATOR SUB-ASSEMBLY RH (See page WW-13) 12 INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH (See page WW-13) 13 INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH (See page WW-14) 14 INSTALL FRONT WIPER ARM HEAD CAP (See page WW-15) WW WW–56 WIPER AND WASHER – WASHER NOZZLE (for Hatchback) WASHER NOZZLE (for Hatchback) ON-VEHICLE INSPECTION INSPECT WASHER NOZZLE (a) Start the engine (b) Check where the washer fluid hits the windshield Standard: Washer fluid hits the windshield in the areas shown in the illustration (1) Front: WW B A E Upper Point C D F H Standard Washer Fluid Contact Area Lower Point G E114462E01 Specification Area Measurement A 115 mm (4.53 in.) B 100 mm (3.94 in.) C 375 mm (14.76 in.) D 85 mm (3.35 in.) E 454 mm (17.87 in.) F 88 mm (3.46 in.) G 178 mm (7.01 in.) WW–57 WIPER AND WASHER – WASHER NOZZLE (for Hatchback) Area Measurement H 31 mm (1.22 in.) (2) Rear: A B WW E108417E01 Specification Area Measurement A 100 mm (3.94 in.) B 100 mm (3.94 in.) WW–58 WIPER AND WASHER – WASHER NOZZLE (for Hatchback) ADJUSTMENT WW REMOVE FRONT WIPER ARM HEAD CAP (See page WW-17) REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH (See page WW-17) REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH (See page WW-17) REMOVE HOOD TO COWL TOP SEAL (See page WW-18) REMOVE COWL TOP VENTILATOR LOUVER SUBASSEMBLY (See page WW-18) REMOVE COWL TOP VENTILATOR LOUVER LH (See page WW-18) REMOVE WASHER NOZZLE (a) Disconnect the washer hose (b) Disengage the claws and remove the front washer nozzle NOTICE: Do not reuse the washer nozzle ADJUST WASHER NOZZLE (a) Select a washer nozzle from the table so as to make the washer fluid hit within the specified area Available Washer Nozzle E114463 Discrimination Number E108416E01 Washer Fluid Injection Angle Part Number Discrimination Number 85381-52250 12 0° 85381-52280 13 + 1° 85381-52290 11 - 1° 85381-52300 14 + 2° 85381-52310 10 - 2° INSTALL COWL TOP VENTILATOR LOUVER LH (See page WW-21) 10 INSTALL COWL TOP VENTILATOR LOUVER SUBASSEMBLY (See page WW-21) 11 INSTALL HOOD TO COWL TOP SEAL (See page WW22) 12 INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH (See page WW-22) 13 INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH (See page WW-23) 14 INSTALL FRONT WIPER ARM HEAD CAP (See page WW-23) WIPER AND WASHER – WASHER LEVEL WARNING SWITCH (for Sedan) WW–59 WASHER LEVEL WARNING SWITCH (for Sedan) BODY ELECTRICAL WIPER AND WASHER COMPONENTS WW CLIP x6 FRONT BUMPER COVER x2 w/ Fog Light: FOG LIGHT CONNECTOR w/ Fog Light: FOG LIGHT CONNECTOR x3 SCREW GROMMET x2 x2 x3 w/ Front Spoiler: FRONT SPOILER COVER x10 x2 E129679E01 WW–60 WIPER AND WASHER – WASHER LEVEL WARNING SWITCH (for Sedan) x2 5.0 (51, 44 in.*lbf) HEADLIGHT ASSEMBLY RH WW 5.5 (56, 49 in.*lbf) x2 WINDSHIELD WASHER JAR ASSEMBLY N*m (kgf*cm, ft*lbf) : Specified torque E129620E01 WIPER AND WASHER – WASHER LEVEL WARNING SWITCH (for Sedan) WW–61 WW WASHER LEVEL WARNING SWITCH E129684E01 WW–62 WIPER AND WASHER – WASHER LEVEL WARNING SWITCH (for Sedan) ON-VEHICLE INSPECTION E129626 WW INSPECT WASHER LEVEL WARNING SWITCH (a) Check the operation of the washer level warning switch (1) Fill the washer jar with washer fluid HINT: The operation should be performed with the washer level warning switch installed on the washer jar (2) Connect the positive (+) battery lead to terminal of the washer level warning switch, and the negative (-) battery lead to terminal (3) Check the resistance HINT: Pull out the washer hose connected to the washer motor Perform the inspection while draining the washer fluid off Standard Resistance Amount of remaining washer fluid Specified Condition 600 to 800 ml or more 10 kΩ or higher 600 to 800 ml or less Below 1Ω If the result is not as specified, replace the washer jar WIPER AND WASHER – WASHER LEVEL WARNING SWITCH (for Sedan) WW–63 REMOVAL DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL REMOVE FRONT SPOILER COVER (w/ Front Spoiler) (See page ET-6) REMOVE FRONT BUMPER COVER (See page ET-6) REMOVE HEADLIGHT ASSEMBLY RH (See page LI86) DRAIN WASHER FLUID (a) Disconnect the washer hoses from the windshield washer motor and pump, and drain the washer fluid REMOVE WINDSHIELD WASHER JAR ASSEMBLY (a) Disconnect the harness clamps (b) Disconnect the connectors (c) Remove the bolts (d) Remove the windshield washer jar E129623 REMOVE WASHER LEVEL WARNING SWITCH (a) Pull the washer motor and pump out of the packing of the washer jar E129627 INSTALLATION E129627 INSTALL WASHER LEVEL WARNING SWITCH (a) Install the washer level warning switch onto the packing of the washer jar WW WW–64 WIPER AND WASHER – WASHER LEVEL WARNING SWITCH (for Sedan) INSTALL WINDSHIELD WASHER JAR ASSEMBLY (a) Install the windshield washer jar E129625 (b) Install the bolts Torque: 5.5 N*m (56 kgf*cm, 49 in.*lbf) (c) Connect the connectors (d) Connect the harness clamps WW E129623 FILL UP WASHER JAR AND PUMP ASSEMBLY WITH WASHER FLUID (a) Connect the washer hose to the washer motor and pump, and fill the washer jar with washer fluid INSTALL HEADLIGHT ASSEMBLY RH (See page LI92) INSTALL FRONT BUMPER COVER (See page ET-16) INSTALL FRONT SPOILER COVER (w/ Front Spoiler) (See page ET-19) CONNECT CABLE TO NEGATIVE BATTERY TERMINAL Torque: 5.4 N*m (55 kgf*cm, 48 in.*lbf)