tài liệu cung cấp thông số kỹ thuật của các loại cửa gió điều hòa dạng dài thuận tiện cho các bạn trong việc tính toán vận tốc gió tại miệng, trở lực tại các miệng điều hòa, kích thước cổ miệng để có thể đặt hàng gia công chế tạo miệng và ống gió phù hợp.
Trang 1Grilles & Registers
Contents
• GV Double Deflection Supply Air Grille 2
• GH Double Deflection Supply Air Grille 4
• GA Supply Air Linear Bar Grille 9
• RA Linear Bar Grille 13
• SLLS Linear Ceiling Diffuser 19
• Accessories 23
GA Supply Air Linear Bar Grille
GH Double Deflection Supply Air Grille
GV Double Deflection Supply Air Grille
RA Linear Bar Grille
SLLS Linear Ceiling Diffuser
Trang 2GV Double Deflection Supply Air Grille
• GV-S Frame 0.7mm, Blade 0.3mm StainlessSteel SUS 304
• GV-A Extruded Aluminium A6063
• Surface Finish:
• GV-T Baked White Powder Coat as standard
• GV-S Stainless Steel Original Colour
• GV-A Baked White Powder Coat orNatural Anodized
• The grille will come in more sections for blade length that is more than 600mm
• Non-standard sizes are available
SPGC Steel
Stainless SteelSUS 304
ExtrudedAluminiumA6063
A
W+10 H+10
B Wall Size
W+20 H+20
D Face Size
W+60 H+60
GV-T GV-S GV-A
Model
Accessories Materials
W H GV-T + G1 - 350X150
Trang 3GV Supply Air Grille & Accessories
GV+G1 Opposed Blade Damper
• GV+G1 Opposed Blade Damper.
• Materials:
• G1-T SPGC Galvanized Steel
• Surface Finish:
• G1-T Baked Black as standard
• The G1 opposed blade damper is gear
operated & can be set at fully open,
half open & fully close
• G1 maximum dimension is 500mm x 500mm
Damper size bigger than this will come in
sections
GV+G2 Volume Extractor
• GV+G2 Volume Extractor.
• G2 volume extractor helps in balancing by
guiding a regulated amount of air for supply air
grilles from the main duct & enable even air
distribution over the entire surface of grille
• Maximum angle for G2 is 35˚ - 40˚
• Materials for G2 is 1.0mm SPGC galvanized
steel & surface finish is baked black
Model
GV
D Face Size
B Wall Size
A Duct Size
NeckSizeDepth
W+60H+60
W+20H+20
W+10H+10
W X H48
GV+G1 T W X H W+15H+15 W+20H+20 W+60H+60
A 123
Trang 4GH Double Deflection Supply Air Grille
• GH-S Frame 0.7mm, Blade 0.3mm StainlessSteel SUS 304
• GH-A Extruded Aluminium A6063
• Surface Finish:
• GH-T Baked White Powder Coat as standard
• GH-S Stainless Steel Original Colour
• GH-A Baked White Powder Coat orNatural Anodized
in front & the vertical set behind
• The grille will come in more sections for blade length that is more than 600mm
• Non-standard sizes are available
SPGC Steel
Stainless SteelSUS 304
ExtrudedAluminiumA6063
A
W+10 H+10
B Wall Size
W+20 H+20
D Face Size
W+60 H+60
GH-T GH-S
Accessories Materials
GH-T + G1 - 350X150
Trang 5GH Supply Air Grille & Accessories
GH+G1 Opposed Blade Damper
• GH+G1 Opposed Blade Damper.
• Materials:
• G1-T SPGC Galvanized Steel
• Surface Finish:
• G1-T Baked Black as standard
• The G1 opposed blade damper is
gear operated & can be set at fully open,
half open & fully close
• G1 maximum dimension is 500mm x 500mm
Damper size bigger than this will come in
sections
GH+G2 Volume Extractor
• GH+G2 Volume Extractor.
• G2 volume extractor helps in balancing by
guiding a regulated amount of air for supply air
grilles from the main duct & enable even air
distribution over the entire surface of grille
• Maximum angle for G2 is 35˚ - 40˚
• Materials for G2 is 1.0mm SPGC galvanized
steel & surface finish is baked black
Model
GH
D Face Size
B Wall Size
A Duct Size
NeckSizeDepth
W+60H+60
W+20H+20
W+10H+10
W X H48
GH+G1 T W X H W+15H+15 W+20H+20 W+60H+60
A 123
Trang 6Performance Data for GV & GH (1)
54.5
43.5
32.5
2
4.63.8
3.02.2
1.71.2
0.8
5.24.2
3.52.5
1.91.4
0.9
7.86.4
5.03.8
2.82.1
1.3
Vel M/S0˚
22˚
45˚
TotalPress(mmAq)
NeckSizemm
NeckArea
m2
EffectiveArea
m2
180162
144126
10890
72
4.5-6.44.2-6.0
3.8-5.73.7-5.2
3.0-4.82.4-4.2
1.8-3.5
3.6-5.13.3-4.8
3.0-4.43.0-4.2
2.4-3.81.8-3.2
1.5-3.0
2.2-3.22.1-3.0
2.0-2.61.8-2.7
1.5-2.41.2-2.0
1.0-1.8
CMH0˚
22˚
45˚
2523
-
-
NC
-Throw(M)
CMH0˚
22˚
45˚
NC
Throw(M)
CMH0˚
22˚
45˚
NC
Throw(M)
CMH0˚
22˚
45˚
NC
Throw(M)
CMH0˚
22˚
45˚
NC
Throw(M)
CMH0˚
22˚
45˚
NC
Throw(M)
CMH0˚
22˚
45˚
NC
Throw(M)
CMH0˚
22˚
45˚
NC
Throw(M)
100 X 100
0.010.005
270243
216189
162135
108
5.0-6.94.7-6.6
4.5-6.13.9-5.7
3.3-5.22.5-4.5
2.2-3.9
4.0-5.63.8-5.3
3.6-4.83.1-4.6
2.8-4.21.9-3.6
1.8-3.1
2.5-3.42.3-3.3
2.1-3.12.1-3.0
1.5-2.71.2-2.4
1.0-2.1
2725
21-
-
-150 X 100
0.0150.009
360324
288252
216180
144
5.5-8.05.2-7.6
4.9-7.04.5-6.7
4.3-6.23.4-5.5
2.8-4.8
4.5-6.54.2-6.0
4.0-5.53.7-5.2
3.4-4.92.8-4.3
2.2-4.0
3.0-3.72.8-3.5
2.5-3.42.2-3.1
1.9-3.01.6-2.8
1.3-2.6
2927
2521
-
-150 X -150
200 X 100
0.020.012
450405
360315
170225
180
6.4-8.86.2-8.4
5.7-7.85.0-7.2
4.8-6.83.9-6.4
3.2-5.7
5.1-7.04.8-6.7
4.5-6.34.2-5.7
3.8-5.43.0-5.2
2.6-4.5
3.3-4.63.1-4.2
2.9-3.92.7-3.6
2.4-3.32.1-3.0
1.5-2.7
3028
2622
-
-250 X 100
0.0250.015
540486
432378
324270
216
7.1-9.86.8-9.4
6.5-8.95.8-8.3
5.5-7.74.3-6.9
3.5-6.2
5.5-7.75.3-7.4
5.2-7.14.6-6.5
4.3-6.23.4-5.4
2.8-4.9
3.4-4.93.2-4.6
3.1-4.32.8-4.0
2.5-3.72.2-3.3
1.8-3.1
3028
2622
-
-200 X 150
300 X 100
0.030.018
630567
504441
378315
252
7.7-10.67.2-10.0
6.8-9.56.5-8.9
5.6-8.34.8-7.5
3.8-6.8
6.2-8.65.7-8.1
5.3-7.75.2-7.1
4.5-6.53.8-5.7
3.0-5.2
3.9-5.23.7-4.9
3.5-4.63.2-4.3
2.8-4.02.3-3.6
1.8-3.2
3229
2723
-
-250 X 150
350 X 100
0.0350.021
720648
576504
432360
288
7.9-11.37.6-10.8
7.3-10.16.7-9.4
6.2-8.85.1-7.9
4.0-7.2
6.4-9.06.2-8.7
5.7-8.25.4-7.6
4.9-7.04.1-6.3
3.2-5.6
4.1-5.63.9-5.3
3.7-5.03.4-4.6
3.0-4.32.7-3.9
2.0-3.4
3330
2824
-
-200 X -200
400 X 100
0.040.025
810729
648567
486405
324
8.4-12.08.1-11.4
7.8-10.87.1-9.9
6.8-9.35.3-8.4
4.2-7.7
6.8-9.56.5-9.1
6.2-8.75.6-8.0
5.4-7.54.4-6.8
3.5-6.2
4.4-6.24.1-5.7
3.9-5.33.5-4.9
3.3-4.62.9-4.3
2.3-3.7
3531
2825
21-
-300 X 150
450 X 100
0.0450.028
• NC value is based on a room absorption of 10 dB, re 10-12 watts
• Dash (-) in space indicates NC value less than 20
• With G1 damper, the pressure loss is 1.136P, and add 2 for NC value
• The performance data is tested based on A.D.C standard
Trang 7Performance Data for GV & GH (2)
54.5
43.5
32.5
2
4.63.8
3.02.2
1.71.2
0.8
5.24.2
3.52.5
1.91.4
0.9
7.86.4
5.03.8
2.82.1
1.3
Vel M/S0˚
22˚
45˚
TotalPress(mmAq)
720630
540450
360
9.2-12.58.5-11.9
7.9-11.37.6-10.6
6.9-9.75.8-8.8
4.5-7.9
7.4-10.16.8-9.5
6.4-9.16.1-8.6
5.5-7.84.6-7.0
3.7-6.4
4.6-6.54.3-5.9
4.0-5.53.7-5.2
3.4-4.93.0-4.6
2.5-3.9
CMH0˚
22˚
45˚
3632
2926
21-
NC
-Throw(M)
CMH0˚
22˚
45˚
NC
Throw(M)
CMH0˚
22˚
45˚
NC
Throw(M)
CMH0˚
22˚
45˚
NC
Throw(M)
CMH0˚
22˚
45˚
NC
Throw(M)
CMH0˚
22˚
45˚
NC
Throw(M)
CMH0˚
22˚
45˚
NC
Throw(M)
CMH0˚
22˚
45˚
NC
Throw(M)
864756
648540
432
9.9-14.09.4-13.1
8.9-12.28.3-11.4
7.4-10.56.3-9.6
4.9-8.6
8.1-11.27.6-10.4
7.1-9.86.7-9.3
5.9-8.44.9-7.8
4.1-6.8
5.0-6.94.7-6.6
4.4-6.24.1-5.8
3.8-5.23.2-4.9
2.6-4.2
3732
2926
21-
1008882
756630
504
10.8-14.810.2-14.2
9.6-13.59.1-12.5
8.3-11.76.9-10.7
5.4-9.6
8.5-12.08.2-11.4
7.8-10.87.3-10.0
6.6-9.45.5-8.6
4.5-7.6
5.4-7.55.2-7.2
4.8-6.84.4-6.4
4.2-5.83.5-5.2
2.8-4.7
3833
3026
21-
11521008
864720
576
11.5-16.011.0-15.2
10.4-14.49.6-13.5
8.9-12.47.3-11.3
5.9-10.1
9.2-12.88.7-12.2
8.3-11.57.8-10.7
7.0-9.95.7-9.2
4.7-8.0
5.9-8.05.6-7.7
5.2-7.24.8-6.8
4.4-6.23.8-5.5
3.0-5.0
3934
3127
22-
12961134
972810
648
12.2-17.011.7-16.2
11.0-15.210.2-14.2
9.4-13.27.8-12.0
6.2-10.7
9.8-13.69.3-12.9
8.8-12.28.2-11.3
7.5-10.56.1-9.6
5.0-8.6
6.2-8.25.8-8.0
5.5-7.65.1-7.1
4.7-6.64.0-5.9
3.2-5.3
3935
3227
23-
14401260
1080900
720
12.8-17.912.2-16.9
11.5-16.010.9-14.9
9.9-13.98.3-2.7
6.6-11.3
10.3-14.49.8-13.6
9.2-12.88.6-12.0
8.0-11.26.5-10.1
5.2-9.1
6.5-8.76.1-8.2
5.7-8.05.4-7.5
5.0-7.04.3-6.4
3.4-5.6
4035
3228
23-
17281512
12961080
964
14.1-19.513.4-18.5
12.6-17.511.8-16.5
11.0-15.19.0-13.9
7.1-12.5
11.3-15.610.7-14.8
10.0-14.09.4-13.3
8.8-12.17.0-11.2
5.6-10.0
6.9-9.86.6-9.3
6.3-8.65.9-8.2
5.4-7.54.5-6.9
3.6-6.3
4036
3329
24-
18721638
14041170
936
14.8-20.514.0-19.2
13.3-18.212.3-17.2
11.5-15.79.3-14.5
7.5-12.9
11.8-16.011.0-15.1
10.5-14.510.0-13.9
9.3-12.77.5-11.8
6.0-10.5
7.2-10.26.7-9.6
6.5-9.06.2-8.5
5.8-7.84.8-7.2
3.9-6.7
4036
3329
24-
GV & GH (2)
• Throw is based on terminal velocities of 0.5 m/s - 0.25 m/s
respectively.
• NC value is based on a room absorption of 10 dB, re 10 -12 watts.
• Dash (-) in space indicates NC value less than 20.
• With G1 damper, the pressure loss is 1.136P, and add 2 for NC value.
• The performance data is tested based on A.D.C standard.
Trang 8Performance Data for GV & GH (3)
54.5
43.5
32.5
2
4.63.8
3.02.2
1.71.2
0.8
5.24.2
3.52.5
1.91.4
0.9
7.86.4
5.03.8
2.82.1
1.3
Vel M/S0˚
22˚
45˚
TotalPress(mmAq)
NeckSizemm
NeckArea
m2
EffectiveArea
m2
27002430
21601890
16201350
1080
15.5-21.814.8-20.8
14.0-19.513.0-18.3
11.8-16.99.7-15.5
8.0-14.0
12.4-17.611.9-16.5
11.2-15.510.2-14.6
9.4-13.67.8-12.4
6.5-11.3
7.8-10.87.4-10.5
6.9-9.76.7-9.1
6.1-8.44.9-7.5
4.0-7.0
CMH0˚
22˚
45˚
4037
3329
24-
NC
-Throw(M)
CMH0˚
22˚
45˚
NC
Throw(M)
CMH0˚
22˚
45˚
NC
Throw(M)
CMH0˚
22˚
45˚
NC
Throw(M)
CMH0˚
22˚
45˚
NC
Throw(M)
CMH0˚
22˚
45˚
NC
Throw(M)
CMH0˚
22˚
45˚
NC
Throw(M)
CMH0˚
22˚
45˚
NC
Throw(M)
28802592
23042016
17281440
1152
16.2-22.715.4-21.4
14.6-20.213.6-19.0
12.4-17.510.2-16.0
8.3-14.5
13.0-18.112.3-17.0
11.6-16.110.6-15.1
9.7-14.08.2-12.8
6.6-11.5
8.2-11.27.7-10.7
7.3-10.16.8-9.4
6.4-8.61.2-2.4
4.1-7.2
4037
3430
24-
32402916
25922268
19441620
1296
17.1-24.016.4-23.0
15.4-21.314.3-19.9
12.8-18.510.9-16.8
8.7-15.2
13.7-19.313.0-18.5
12.3-16.911.3-15.8
10.2-14.78.7-13.5
7.0-12.2
8.5-11.98.2-11.5
7.6-10.77.3-9.9
6.5-9.35.4-8.3
4.3-7.6
4138
3530
2521
36003240
28802520
21601800
1440
18.0-25.217.1-24.0
16.2-22.614.9-21.0
13.6-19.611.4-17.9
9.2-16.0
14.3-20.113.7-19.3
13.0-18.012.0-16.7
10.8-15.59.1-14.3
7.5-12.8
8.9-12.78.5-11.9
8.0-11.37.5-10.5
6.8-9.85.7-8.7
4.5-7.9
4138
3530
2521
40503645
32402835
24302025
1620
19.1-26.818.1-25.5
17.1-24.016.0-22.3
14.5-20.712.0-19.0
9.8-16.8
15.6-21.214.7-20.3
13.8-19.212.7-17.8
11.4-16.49.6-15.2
7.9-13.5
9.5-13.59.0-12.9
8.4-11.97.9-11.0
7.2-10.36.0-9.4
4.8-8.2
4139
3631
2622
45004050
36003150
27002250
1800
20.1-28.219.0-26.7
17.9-25.217.0-23.5
15.0-21.612.6-19.7
10.2-17.8
16.1-22.415.3-21.3
14.4-20.113.5-18.7
11.8-17.210.0-15.9
8.2-14.3
10.0-14.29.5-13.5
8.8-12.68.4-11.6
7.4-10.76.2-9.7
5.0-8.7
4239
3632
2722
-850 X 300
1000 X 250
0.250.17
48604374
38883402
29152430
1944
21.0-29.219.8-27.8
18.7-26.317.5-24.5
15.6-22.713.1-20.7
10.5-18.5
16.8-23.315.9-22.2
15.0-21.014.0-19.5
12.4-18.010.5-16.5
8.5-14.7
10.5-14.69.9-13.9
9.3-13.08.7-12.2
7.7-11.36.5-10.2
5.3-9.2
4239
3632
2722
-900 X 300
0.270.19
54004860
43203780
32402700
2160
22.2-31.020.9-29.3
19.6-27.718.5-26.0
16.3-24.113.7-21.6
11.0-19.5
17.8-24.616.8-23.4
15.8-22.214.9-20.7
13.0-19.211.0-17.3
8.9-15.5
11.0-15.410.5-14.6
9.9-13.89.3-12.9
8.0-12.06.7-10.7
5.5-9.7
4340
3732
2823
-1000 X 300
0.30.21
• NC value is based on a room absorption of 10 dB, re 10-12watts
• Dash (-) in space indicates NC value less than 20
• With G1 damper, the pressure loss is 1.136P, and add 2 for NC value
• The performance data is tested based on A.D.C standard
Trang 9GA Supply Air Linear Bar Grille
GA Supply Air Linear Bar Grille
Construction Illustration
• Model GA is made up of two sets of
air foil blades
The horizontal set is in front & the vertical
set is behind
• The horizontal set of air blades is fixed & the
vertical set is adjustable
• The grille will come in more sections for blade
length that is more than 600mm
• Non-standard sizes are available
Physcal Dimension
B Wall Size
W+15 H+15
D Face Size
W+48 H+48 GA-A
Model
Accessories Materials
GA-A+G1-400X150
Trang 10GA Linear Bar Grille & Accessories
GA+G1 Opposed
Blade Damper
• GA+G1 Opposed Blade Damper.
• Materials:
• G1-T SPGC Galvanized Steel
• Surface Finish:
• G1-T Baked Black as standard
• The G1 opposed blade damper is gear operated & can be set at fully open, half open & fully close
• G1 maximum dimension is 500mm x 500mm.Damper size bigger than this will come in sections
GA+G2 Volume
Extractor
• GA+G2 Volume Extractor.
• G2 volume extractor helps in balancing byguiding a regulated amount of air for supply airgrilles from the main duct & enable even airdistribution over the entire surface of grille
• Maximum angle for G2 is 35˚ - 40˚
• Materials for G2 is 1.0mm SPGC galvanizedsteel & surface finish is baked black
ModelGA
D Face Size
B Wall Size
A Duct Size
NeckSizeDepth
W+48H+48
W+15H+15
W+10H+10
W X H52
GA+G1 T W X H W+15H+15 W+15H+15 W+48H+48
A 127
Trang 11Performance Data for GA (1)
54.5
43.5
32.5
2
4.84.0
3.02.3
1.81.2
0.9
810729
648567
486405
4.2-6.13.9-5.6
3.6-5.02.9-4.5
2.3-4.1
8.3-11.88.1-11.2
7.3-10.67.0-9.4
6.5-8.85.2-8.3
4.3-7.5
3732
2725
21-
-CMHCeilingWallNC
Throw(M)
CMHCeilingWallNC
Throw(M)
CMHCeilingWallNC
Throw(M)
CMHCeilingWallNC
Throw(M)
CMHCeilingWallNC
Throw(M)
CMHCeilingWallNC
Throw(M)
CMHCeilingWallNC
Throw(M)
CMHCeilingWallNC
Throw(M)
CMHCeilingWallNC
Throw(M)
450 X 100
300 X 150
0.045
1080972
864756
648540
432
6.1-8.35.7-8.0
5.3-7.44.7-6.7
4.1-6.13.4-5.2
2.5-4.6
10.0-13.69.5-13.0
9.0-12.48.4-11.3
7.5-10.66.3-9.5
4.6-8.5
3732
2926
21-
1080945
810675
540
6.9-9.56.3-8.9
5.8-8.35.5-7.7
4.9-7.13.9-6.3
2.8-5.3
10.9-15.210.3-14.4
9.7-13.69.2-12.6
8.4-12.07.1-11.2
5.3-9.8
3833
3126
22-
12961134
972810
648
7.6-11.07.1-10.3
6.5-9.56.1-8.4
5.5-7.84.6-7.0
3.5-6.2
12.0-16.911.5-16.0
10.6-15.010.0-13.8
9.2-12.77.6-11.9
6.1-10.5
3835
3127
22-
14401260
1080900
720
8.8-12.08.1-11.1
7.6-10.26.9-9.4
6.2-8.65.1-7.6
4.0-6.8
13.0-18.012.3-16.9
11.8-15.810.8-14.9
10.0-14.08.2-12.5
6.8-11.4
3936
3128
23-
17281512
12961080
864
9.3-12.98.8-12.2
8.1-11.37.4-10.4
6.5-9.55.3-8.4
4.3-7.4
14.0-19.513.5-18.6
12.6-17.611.7-16.5
10.9-15.19.0-13.8
7.2-12.4
3936
3329
24-
19441700
14581215
972
9.8-13.89.3-13.0
8.6-12.27.7-11.2
6.7-10.25.6-8.9
4.5-7.9
14.8-20.714.2-19.7
13.4-18.512.5-17.4
11.3-16.09.4-14.7
7.5-13.2
3936
3430
24-
21601890
16201350
1080
10.5-14.89.8-13.8
9.1-12.88.3-11.6
7.3-10.96.1-9.5
4.8-8.6
15.3-21.614.6-20.7
13.8-19.313.0-18.2
11.7-17.09.5-15.4
7.7-13.8
3937
3430
25-
23762079
17821485
1188
11.1-15.710.4-14.6
9.7-13.58.7-12.4
7.7-11.46.4-10.1
5.1-9.1
16.2-22.815.1-21.5
14.6-20.413.5-19.0
12.4-17.610.2-16.1
8.2-14.6
3937
3531
2521
GA (1)
• Throw is based on terminal velocities of 0.5 m/s - 0.25 m/s
respectively
• NC value is based on a room absorption of 10 dB, re 10-12watts
• Dash (-) in space indicates NC value less than 20
• With G1 damper, the pressure loss is 1.136P, and add 2 for NC value
• The performance data is tested based on A.D.C standard
Trang 12Performance Data for GA (2)
Performance
Data for
GA (2)
54.5
43.5
32.5
2
4.84.0
3.02.3
1.81.2
0.9
32402915
25922268
19441620
1296
Vel M/S
Tot Press (mmAq)
NeckSizemm
NeckArea
m2
12.0-16.911.0-15.6
10.2-14.39.0-13.2
7.9-12.16.5-10.8
5.3-9.5
16.9-23.816.2-22.5
15.2-21.314.2-19.8
12.7-18.310.7-16.9
8.5-15.2
4038
3531
2521
-CMHCeilingWallNC
Throw(M)
CMHCeilingWallNC
Throw(M)
CMHCeilingWallNC
Throw(M)
CMHCeilingWallNC
Throw(M)
CMHCeilingWallNC
Throw(M)
CMHCeilingWallNC
Throw(M)
CMHCeilingWallNC
Throw(M)
CMHCeilingWallNC
Throw(M)
CMHCeilingWallNC
Throw(M)
600 X 300
700 X 2500.18
35103160
28082457
21051755
1405
12.6-17.611.7-16.4
10.8-15.19.7-13.9
8.7-12.67.3-11.4
5.8-10.1
17.7-24.916.8-23.5
15.8-22.114.7-20.7
13.2-19.011.2-17.2
9.1-15.8
4038
3531
2521
-650 X 300
550 X 3500.195
37803402
30242646
22681890
1512
13.3-18.512.3-17.2
11.3-15.910.3-14.5
9.3-13.17.8-11.8
6.1-10.6
18.7-26.017.5-24.5
16.6-23.315.3-21.5
14.0-19.711.6-18.1
9.6-16.5
4138
3531
2621
-700 X 300
1000 X 2000.21
40503645
32402835
24302025
1620
14.2-19.813.3-18.2
12.2-16.911.0-15.5
9.6-13.88.3-12.5
6.5-11.1
19.3-26.918.0-25.6
17.2-24.016.0-22.4
14.5-20.512.1-18.6
10.0-17.1
4139
3631
2622
-750 X 300
900 X 2500.225
43203888
34563024
25922160
1728
14.7-20.413.6-19.2
12.5-17.711.4-16.0
10.2-14.38.5-13.0
6.7-11.4
19.9-27.718.6-26.3
17.6-24.716.6-23.1
14.8-21.112.5-19.5
10.2-17.5
4139
3632
2622
-850 X 3000.24
45904130
36723213
27542295
1836
15.1-21.114.3-20.0
12.9-18.211.6-16.6
10.4-15.08.6-13.4
6.9-11.8
20.5-28.519.3-27.0
18.2-25.517.3-23.8
15.2-21.912.9-20.0
10.4-18.0
4139
3632
2722
-850 X 3000.255
48604374
38883402
29152430
1944
15.5-21.714.7-20.6
13.3-19.121.1-17.4
10.7-15.78.9-14.0
7.0-12.3
21.0-29.319.6-27.9
18.7-26.517.5-24.5
15.6-22.613.0-20.6
10.5-18.4
4239
3632
2722
-900 X 3000.27
54004860
43203780
32402700
2160
16.6-23.015.5-21.7
14.2-20.213.0-18.4
11.3-16.99.3-14.8
7.3-12.9
22.5-31.121.0-29.5
19.9-27.218.6-26.0
16.4-24.013.6-21.7
11.0-19.5
4340
3732
2823
-1000 X 3000.3
57605184
46084032
34562880
2304
17.0-23.715.8-22.1
14.4-21.413.3-19.4
11.5-17.59.5-15.2
7.5-13.2
23.0-32.021.7-30.5
20.2-28.718.9-26.9
16.7-24.714.1-22.2
11.4-19.9
4340
3732
2823
-800 X 4000.32
• Throw is based on terminal velocities of 0.5 m/s - 0.25 m/s respectively
• NC value is based on a room absorption of 10 dB, re 10-12watts
• Dash (-) in space indicates NC value less than 20
• With G1 damper, the pressure loss is 1.136P, and add 2 for NC value
• The performance data is tested based on A.D.C standard