DSpace at VNU: Effects of pH and salt concentration on functional properties of rambutan (Nephelium lappaceum L.) seed albumin concentrate

1212 International Journal of Food Science and Technology 2016, 51, 1212–1219 Original article Effects of pH and salt concentration on functional properties of rambutan (Nephelium lappaceum L.) seed albumin concentrate Huynh Thanh Hai Vuong, Ngoc Minh Chau Tran, Thi Thu Tra Tran, Nu Minh Nguyet Ton & Van Viet Man Le* Department of Food Technology, Ho Chi Minh City University of Technology, 268 Ly Thuong Kiet street, District 10, Ho Chi Minh City, Vietnam (Received December 2015; Accepted in revised form 10 February 2016) Summary Searching new protein sources is essential due to an increase in protein demand In this study, rambutan seed albumin concentrate (RSAC) with the protein content of 80.8% was isolated from defatted rambutan seed meal The effects of pH and sodium chloride concentration on solubility and functional properties of RSAC were investigated RSAC had minimum solubility at pH Water absorption capacity at pH and oil absorption capacity of RSAC were 0.79 and 6.13 mL gÀ1, respectively Both foaming and emulsifying capacities achieved maximal levels at pH 12 In sodium chloride solution, foaming capacity and stability achieved maximal levels at the concentration of 0.6 mol LÀ1, while the highest emulsifying capacity and stability were noted at the concentration of 0.2 mol LÀ1 The least gelation concentration of RSAC was 100 g LÀ1 and this value decreased by five times as salt concentration in the protein solution was 0.6 mol LÀ1 RSAC was a potential functional ingredient in food processing Keywords Albumin, functional properties, pH, rambutan seed, salt concentration Introduction In food industry, proteins not only contribute to nutritional value but also affect physico-chemical characteristics and sensorial properties of food (Yada, 2004) Plant proteins have attracted great attention due to low cost and high productivity According to Osborne classification, plant proteins consisted of four major fractions: water-soluble albumin, salt-soluble globulin, alkaline-soluble glutelin and alcohol-soluble prolamin The ratio of protein fractions varied from plant to plant Increase in world population increases the demand for protein Although conventional plant protein sources including soy, wheat, sorghum, lupin and chickpeas have been widely and effectively used for human consumption, searching new protein sources is essential for protein demand in developing countries (Day, 2013) Rambutan (Nephelium lappaceum L.) is a popular crop widely cultivated in tropical countries Rambutan fruits have been used in the production of juice, jam, jelly, marmalade and canned fruit in syrup The percentage of seed varied from to 9% fruit weight *Correspondent: Fax: +84 38637504; e-mail: lvvman@hcmut.edu.vn (Sirisompong et al., 2011) In some Asian countries, rambutan seeds are edible after roasting, while in others, the seeds are considered as a waste material (Solıs-Fuentes et al., 2010) The oil and protein contents in rambutan seeds were 37.1–38.9% and 11.9– 14.1%, respectively (Augustin & Chua, 1988) Some studies focused on rambutan seed oil, the physicochemical and thermal characteristics of which may become interesting for specific applications in several segments of the food industry (Solıs-Fuentes et al., 2010; Sirisompong et al., 2011) After oil extraction, protein is one of the valuable components in the obtained residue and defatted rambutan seed meal (DFRM) can be considered as a nonconventional protein source There have been so few studies on rambutan seed proteins According to Augustin & Chua (1988), the amino acid profile of rambutan seed proteins showed that the proteins were of good quality for food use Our preliminary study revealed that albumin was the major protein fraction in rambutan seeds (Data not shown) Albumin can be extracted by water which is an inexpensive and eco-friendly solvent In addition, water did not modify native structure of the extracted proteins as well as their functional properties as compared with other solvents such as salt solution, alkaline or alcohol (Yada, 2004) Many doi:10.1111/ijfs.13087 © 2016 Institute of Food Science and Technology Effects of pH and salt concentration H T H Vuong et al studies reported functional properties and effects of processing parameters on functional properties of water-soluble proteins from different plant sources including great northern bean (Sathe & Salunkhe, 1981), oat seed (Ma & Harwalkar, 1984), tepary bean (Idouraine et al., 1991), wheat germ (T€ om€ osk€ ozi et al., 1998), pea seed (Lu et al., 2000; Adebiyi & Aluko, 2011), African locust bean (Lawal et al., 2005), ginkgo seed (Deng et al., 2011) and kidney bean (Mundi & Aluko, 2012) These efforts were aimed at effective application of unconventional protein sources to formulation of new food products However, functional properties of rambutan seed albumin concentrate (RSAC) have never been reported In this study, RSAC was prepared from DRSM The effects of pH and salt concentration on solubility and functional properties of the RSAC were investigated for the purpose of evaluating the potentiality of this new protein source in food product formulation The investigated functional properties included water and oil absorption capacity, emulsifying capacity, emulsion stability, foaming capacity, foam stability and gelation capacity Materials and methods 30 and the supernatant was adjusted to pH 4.2 using HCl solution (0.1 mol LÀ1) for albumin precipitation The solid phase was recovered by centrifugation at 5000 g, 20 °C for 30 and re-dissolved in de-ionised water The procedure of albumin precipitation was repeated twice Finally, the precipitate was freeze-dried, ground and stored at À18 °C Proximate composition of albumin concentrate Protein content was determined by Kjeldahl method (Bradstreet, 1965) Total sugar and reducing sugar contents were evaluated by spectrophotometric method with phenol–sulphuric acid (DuBois et al., 1956) and 3,5-dinitrosalicylic acid (Miller, 1959), respectively Polyphenol content was measured by spectrophotometric method using Folin–Ciocalteu reagent (Singleton & Rossi, 1965) The moisture, ash, lipid and total acid contents were analysed using AOAC official methods (Helrich, 1990) Surface hydrophobicity of soluble proteins was measured by fluorescence spectrometric method described by Kato & Nakai (1980) using 8-anilino-1-naphthalene sulphonate Sulfhydryl group content was determined according to the method described by Thannhauser et al (1987) Materials Seeds of rambutan (Nephelium lappaceum L.) fruits were originated from a canned fruit processing plant in Dong Nai, Vietnam The seeds were ground, defatted with hexan at 40 °C for 36 h and stored at À18 °C before use De-ionised water was used as extraction solvent All chemicals used in this study were of analytical grade and purchased from Sigma-Aldrich (St Louis, MO, USA) Preparation of rambutan seed albumin concentrate For albumin extraction, 100 g defatted rambutan seed meal and L de-ionised water were mixed at 200 rpm, 30 °C for h The mixture was centrifuged at 1500 g, 20 °C for 30 for solid removal The extract was dialysed against distilled water to remove salts and to coagulate contaminating salt-soluble protein fraction (globulin) using a membrane with molecular weight cut-off of KDa (Biovision, Milpitas, CA, USA) The dialysis bag was placed in a beaker containing distilled water The outer phase was continuously stirred using a magnetic stirrer The dialysis was performed at the ambient temperature After h, the dialysis bag was removed and the liquid phase in the beaker was replaced by distilled water The dialysis was repeated three times Upon completion of dialysis, the content of dialysis bag was centrifuged at 5000 g, 20 °C for © 2016 Institute of Food Science and Technology Protein solubility Protein solubility was determined by the method of Lawal et al (2005) The protein sample (125 mg) was dispersed in distilled water (25 mL), and the slurry was adjusted to the desired pH (2–12) using HCl solution (0.5 mol LÀ1) or NaOH solution (0.5 mol LÀ1) The slurry was mixed at 30 °C for h with a magnetic stirrer before centrifuging at 12 000 g for 20 at °C Protein content in the supernatant was determined by Kjeldahl method The nitrogen solubility index (NSI) (%) was calculated as follows: NSI ¼ Amount of nitrogen in the supernatant (g)= Amount of nitrogen in the initial sample (g) Effects of NaCl concentration (0–1 mol LÀ1) on protein solubility were also investigated Water absorption capacity and oil absorption capacity Water absorption capacity (WAC) and oil absorption capacity (OAC) were measured by the method of Lawal et al (2005) The protein sample (1 g) was mixed with distilled water (10 mL) or soybean oil (10 mL) for 30 s The samples were then kept at 30 Ỉ °C for 30 before centrifuging at 5000 g for 30 The volume of supernatant was noted in a 10-mL graduated cylinder WAC and OAC were International Journal of Food Science and Technology 2016 1213 1214 Effects of pH and salt concentration H T H Vuong et al calculated as mL water or mL oil trapped by g protein sample Effects of pH (2–12) and NaCl concentration (0–1 mol LÀ1) on WAC were studied Emulsifying capacity and emulsion stability Emulsifying capacity (EC) and emulsion stability (ES) were evaluated using the method suggested by Pearce & Kinsella (1978) The protein sample (500 mg) was dissolved in Britton-Robinson Universal buffer (100 mL) Then, mL the protein dispersion and mL soybean oil were mixed and homogenised at 2000 rpm for using a Heidolph Diax 900 homogeniser (Heidolph Instruments GmbH & Co., Schwabach, Germany) At and 10 after the homogenization, 0.05 mL of the obtained emulsion was pipetted from the bottom of the tube and subsequently diluted into 10 mL of the same buffer containing sodium dodecyl sulphate (1 g LÀ1) Absorbance of the diluted sample was recorded at 500 nm using a spectrophotometer The absorbance obtained at the initial time after being homogenised was the EC The ES was calculated as follows: ES ẳ A0 =DAị Dt where A0 is the absorbance of the diluted emulsion immediately after homogenization, and ΔA is the reduction in absorbance at the interval time (Δt) Effects of pH (2–12) and salt concentration (0–1 mol LÀ1) on EC and ES of the RSAC were examined Foaming capacity and foam stability Foaming capacity (FC) and foam stability (FS) were evaluated by the method described by Deng et al (2011) The protein sample (2 g) was dispersed in distilled water (100 mL), and the mixture was adjusted to the desired pH (2–12) or NaCl concentration (0– mol LÀ1) The resulting blend was vigorously stirred for by a Heidolph Diax 900 homogeniser (Heidolph Instruments GmbH & Co.) The blend was immediately transferred into a 100-mL graduated cylinder The volume was recorded before and after stirring In addition, foam volume change in the graduated cylinder was also recorded at 120 of storage FC (%) and FS (%) were calculated as follows: Gelation capacity Gelation capacity was evaluated by least gelation concentration (LGC) using the method described by Lawal et al (2005) Rambutan seed albumin concentrate was added to distilled water; the solid content of sample suspensions was varied from 10 to 200 g LÀ1 with the increment of 10 g LÀ1 Each test tube contained mL sample suspension The suspension was mixed on a vortex mixer for and heated in a boiling water bath for h The mixture was cooled in a water bath at °C for h after which the tube was inverted The lowest concentration at which the sample did not fall down or slip from an inverted tube was taken as the LGC Effects of pH were evaluated by adjusting pH of the sample suspensions to various values (2–10) prior to heating Effects of salt concentration were investigated by preparing sample suspensions in NaCl solution with different concentrations (0–1 mol LÀ1) Statistical treatment All experiments were performed in triplicate The experimental results were expressed as means Ỉ standard deviations Mean values were considered significantly different when P < 0.05 One-way analysis of variance was performed using the software Statgraphics Centurion XV Results and discussion Proximate composition of albumin concentrate Table shows that the protein level in the RSAC was similar to that in the albumin concentrate from great northern bean (81.70%) (Sathe & Salunkhe, 1981), pea seed (86.26%) (Adebiyi & Aluko, 2011) and ginkgo seed (87.70%) (Deng et al., 2011) Among the nonpr otein compounds, reducing sugars may participate in Maillard reactions while polyphenols may take part in protein–polyphenol interactions These reactions could change both nutritional value and functional properties of proteins (Belitz et al., 2009) It can be noted that the RSAC had higher total and free sulfhydryl content as well as higher surface hydrophobicity than the ginkgo seed albumin (Deng et al., 2011) According to Belitz et al (2009), sulfhydryl content could enhance gelation capacity, while surface FC ẳ ẵVolume after stirring -Volume before stirringŠ ðmLÞ=Volume before stirring ðmL Þ; FS ẳ ẵVolume after 120 standing -Volume before stirring mLị= ẵVolume after stirring -Volume before stirring mLị: International Journal of Food Science and Technology 2016 © 2016 Institute of Food Science and Technology Effects of pH and salt concentration H T H Vuong et al Table Proximate composition of rambutan seed albumin concentrate (n = 6) Moisture (%) Protein (%) Lipid (%) Total sugars (%) Reducing sugars (%) Ash (%) Total acid (%) Polyphenols (%) Free SH content (lmol gÀ1) Total SH content (lmol gÀ1) Surface hydrophobicity (S0) hydrophobicity could improve foaming properties of proteins 4.33 80.78 0.27 5.69 1.04 4.43 0.78 0.77 26.70 82.70 652.72 emulsifying Ỉ Æ Æ Æ Æ Æ Æ Æ Æ Æ Æ 0.15 2.38 0.01 0.12 0.01 0.21 0.01 0.01 1.13 3.51 6.74 and The effects of salt concentration on the NSI of the RSAC are visualised on Fig 1b Increase in salt concentration from to mol LÀ1 gradually reduced the NSI from 66.7% to 41.7% It was reported that the solubility of pumpkin seed albumin in NaCl solutions (0.5 and 1.0 mol LÀ1) was also lower than that in deionised water Salt ions could remove hydrate layers around protein molecules and that led to a reduced protein solubility (Rezig et al (2016) However, these results were different to the previous findings of Deng et al (2011) who reported that increase in salt concentration up to 0.5 mol LÀ1 improved the NSI of ginkgo seed albumin due to salting-in effect Difference in solubility of rambutan seed albumin and gingko seed albumin in a salt solution was probably due to their various conformational characteristics Protein solubility Water absorption capacity Solubility profile of a protein concentrate is a good index of its functional properties and potential applications (Kinsella & Melachouris, 1976) The pH-solubility profile of RSAC is visualised on Fig 1a The lowest NSI (15.56%) was recorded at pH Similar pH value was also reported for minimum solubility of water-soluble proteins from tepary bean (Idouraine et al., 1991) and pea seed (Adebiyi & Aluko, 2011) However, the lowest solubility of African locust albumin (Lawal et al., 2005) and kidney bean albumin (Mundi & Aluko, 2012) was observed at pH Albumins from different plant sources showed various pI values probably due to difference in amino acid composition In the isoelectric region, low electrostatic repulsive forces enhanced the formation of protein aggregates and reduced the protein solubility (Mao & Hua, 2012) On the contrary, the NSI of RSAC increased as the pH decreased from to or increased from to since the electrostatic repulsive forces between protein molecules increased protein–solvent interactions (Belitz et al., 2009) It can be noted that the solubility of the RSAC was nearly unchanged as the pH varied from to 12 Figure 2a presents that Water absorption capacity (WAC) of RSAC decreased with the increase in pH from to and then increased when the pH raised from to The lowest WAC (0.69 mL gÀ1) was observed at pH which was near the pI value of the rambutan seed albumin Interaction between protein molecules was enhanced in the isoelectric region and that resulted in poor WAC (Deng et al., 2011) As the pH was above 9, WAC of RSAC was reduced Alkali solution can break hydrogen, amide and disulphide bonds in protein molecules (Fabian & Ju, 2011) and that could change WAC as well as other functional properties of proteins In distilled water, the WAC of RSAC was 0.79 mL gÀ1 which was higher than that of ginkgo seed albumin (0.41 mL gÀ1) (Deng et al., 2011) Nevertheless, RSAC showed much lower WAC than great northern bean albumin (3.18 mL gÀ1) (Sathe & Salunkhe, 1981), oat seed albumin (2.4 mL gÀ1) (Ma & Harwalkar, 1984), African locust bean albumin (3 mL gÀ1) (Lawal et al., 2005) and kidney bean albumin (3.4 mL gÀ1) (Mundi & Aluko, 2012) Low WAC of protein was due Figure Effects of pH and NaCl concentration on solubility of rambutan seed albumin concentrate (Results were average of three replicate ặ standard deviation) â 2016 Institute of Food Science and Technology (b) 80 Nitrogen soluble index (%) Nitrogen soluble index (%) (a) 80 60 40 20 60 40 20 0 10 11 12 pH value 0.2 0.4 0.6 0.8 NaCl concentration (mol L–1) International Journal of Food Science and Technology 2016 1215 Effects of pH and salt concentration H T H Vuong et al (b) Water absorption capacity (mL g–1) (a) Water absorption capacity (mL g–1) 1216 1.5 0.5 1.5 0.5 10 11 12 pH value 0.2 0.4 0.6 0.8 NaCl concentration (mol L–1) to its high solubility in distilled water (El-Adawy, 2000) Figure 2b demonstrates that increase in salt concentration from to 0.6 mol LÀ1 enhanced WAC of RSAC while further increase in salt concentration reduced the WAC Similar observation was noted for both ginkgo seed albumin (Deng et al., 2011) and African locust bean albumin (Lawal et al., 2005) At low salt concentration, hydrated salt ions could link to charged groups on protein molecules; increase in WAC was due to water molecules which were bound to the salt ions However, high salt concentration increased the interactions between water molecules and salt ions; this led to dehydration of the proteins and subsequent reduction in WAC (Lawal et al., 2005) Proteins with high WAC could contribute to the body and freshness of various viscous foods such as soups, dough, custards and baked products (Kinsella & Melachouris, 1976) Oil absorption capacity The Oil absorption capacity (OAC) of RSAC was 6.13 mL gÀ1 which was much higher than that of great northern bean albumin (3.29 mL gÀ1) (Sathe & Salunkhe, 1981), oat seed albumin (2.8 mL gÀ1) (Ma & Harwalkar, 1984), African locust bean albumin (3.4 mL gÀ1) (Lawal et al., 2005) and kidney bean albumin (2.37 mL gÀ1) (Mundi & Aluko, 2012) The OAC of RSAC (6.13 mL gÀ1) was lower than that of ginkgo seed albumin (9.3 mL gÀ1) (Deng et al., 2011) although the surface hydrophobicity of RSAC (S0 = 652.7) was much higher than that of ginkgo seed albumin (S0 = 23.5) Difference in OAC was probably due to various conformational characteristics, lipophilic groups, surface hydrophobicity (Kinsella & Melachouris, 1976) and nonprotein compounds in the protein concentrates (Yada, 2004) The OAC of protein could affect its emulsifying as well as flavour binding properties (Mundi & Aluko, 2012) Protein concentrate with high oil absorption could be used in the formulation of different products such as sausages, International Journal of Food Science and Technology 2016 Figure Effects of pH and NaCl concentration on water absorption capacity of rambutan seed albumin concentrate (Results were average of three replicate Æ standard deviation) cake batters, mayonnaise and salad dressings (Chandi & Sogi, 2007) Foaming properties Figure 3a presents that FC of RSAC decreased with the increase in pH from to while further increase in pH improved FC It was reported that FC was pH dependent and protein solubility was a prerequisite for good FC (Mundi & Aluko, 2012) Proteins with high solubility could diffuse easily and rapidly to the air–water interface for air bubble encapsulation and that leads to an improved FC (Belitz et al., 2009) The lowest FC (55.2%) was observed at pH which was the point of least solubility of RSAC In the isoelectric region, low solubility of kidney bean albumin (Mundi & Aluko, 2012) also resulted in low FC It was noteworthy that the NSI of RSAC remained unchanged in the pH range of 7–12 However, the FC of RSAC was improved with the increase in pH from to 12 and achieved maximum of 232.8% at pH 12 It can be explained that as the pH raised from to 12, the net charge of RSAC augmented and this phenomenon could weaken hydrophobic interactions and enhance protein flexibility for air bubble encapsulation (Chau et al., 1997) In addition, pH 12 enhanced protein deformability (Fabian & Ju, 2011) which could facilitate the formation of cohesive films around air bubbles (Belitz et al., 2009) Figure 3b shows that maximum FS was recorded at pH This observation agreed with the findings of Lawal et al (2005) who reported that at the isoelectric point, protein film surrounding the air bubbles was stabilised due to the lack of repulsive forces between protein molecules and that generated an improved FS Nevertheless, our result contrasted with the data of Deng et al (2011) who stated that protein aggregation at the isoelectric point resulted in reduced FS It can be noted that conformational characteristics of various proteins at the isoelectric point were different As a result, protection of air bubbles by protein film in foam system could be different © 2016 Institute of Food Science and Technology Effects of pH and salt concentration H T H Vuong et al (b) 100 Foaming stability (%) Foaming capacity (%) (a) 300 200 100 75 50 25 10 11 12 pH value Figure Effects of pH and NaCl concentration on foaming capacity and stability of rambutan seed albumin concentrate (Results were average of three replicate Ỉ standard deviation) (d) Foaming stability (%) Foaming capacity (%) (c) 150 100 50 0 0.2 0.4 0.6 0.8 NaCl concentration (mol L–1) The effects of salt concentration on foaming properties of RSAC are visualised on Fig 3c,d As the salt concentration increased from to 0.6 mol LÀ1, the FC and FS increased by 79% and 25%, respectively It should be noted that increase in salt concentration from to 0.6 mol LÀ1 decreased the NSI of the RSA by 31% Low protein solubility negatively affected foaming properties (Yada, 2004) However, our results showed that the surface hydrophobicity of RSAC increased by 22% when the salt concentration augmented from to 0.6 mol LÀ1 Proteins with high surface hydrophobicity could be easily adsorbed at the air–water interface via hydrophobic areas and generate cohesive film around air bubbles; high surface hydrophobicity of proteins was an important characteristic for foam formation and stabilization (Belitz et al., 2009) When the salt concentration was higher than 0.6 mol LÀ1, both FC and FS of RSAC were reduced Deng et al (2011) also noted a reduction in FC and FS of ginkgo seed albumin as the salt concentration was higher than 0.5 mol LÀ1 These authors explained that high salt concentration promoted protein aggregation and that led to decreased foaming properties In distilled water, the FC and FS of RSAC were comparable to those of ginkgo seed albumin (Deng et al., 2011) and African locust bean albumin (Lawal et al., 2005) Proteins with good foaming properties would be used for foam stabilization in some foods © 2016 Institute of Food Science and Technology 10 11 12 pH value 100 75 50 25 0 0.2 0.4 0.6 0.8 NaCl concentration (mol L–1) such as baked goods, sweets and desserts (Kinsella & Melachouris, 1976) Emulsifying properties The effects of pH on EC and ES of RSAC were described as U-shaped curves (Fig 4a,b) Similar results were mentioned for African locust bean albumin (Lawal et al., 2005) Minimum EC and ES were recorded in the isoelectric region (pH 4) Under strong acidic (pH 2) or alkaline conditions (pH 12), the emulsifying properties were strongly improved EC achieved maximum at pH 12, while the highest ES was noted at pH Emulsifying properties of a protein depended on its hydrophilic–lipophilic balance as well as net charge, which were affected by pH value (Ragab et al., 2004) Extreme acidic or alkaline pH may promote partial denaturation of protein; this phenomenon could facilitate mutual cohesion between oil phase and protein and result in stabilised protein film around dispersed droplets in the emulsion (Lawal et al., 2005) As the salt concentration increased from to 0.2 mol LÀ1, the EC and ES of RSAC achieved maximum while further increase in salt concentration reduced both EC and ES (Fig 4c,d) Low salt concentration may facilitate formation of charged layers around oil droplets and that would result in mutual repulsion between dispersed droplets in oil-in-water International Journal of Food Science and Technology 2016 1217 Effects of pH and salt concentration H T H Vuong et al (b) 40 Emulsion stability (min) Emulsifying ability (Abs) (a) 0.8 0.6 0.4 0.2 30 20 10 10 11 12 pH value 10 11 12 pH value (d) 20 Emulsion stability (min) (c) 0.5 Emulsifying ability (Abs) 1218 0.4 0.3 0.2 0.1 15 10 0 0.2 0.4 0.6 0.8 NaCl concentration (mol L–1) 0.2 0.4 0.6 0.8 NaCl concentration (mol L–1) emulsion As a consequence, protein emulsifying properties would be improved (Yuliana et al., 2014) In addition, low salt concentration could promote formation of hydrate layers around interfacial material and that would reduce interfacial energy and retard coalescence of the oil droplets in the emulsion (Lawal et al., 2005) Nevertheless, high salt concentration reduced the emulsifying properties due to salting-out effect (Ragab et al., 2004) Proteins with good emulsifying properties would be used in formulation of various food emulsions (Yada, 2004) Gelation capacity Table reveals that the LGC of RSAC in distilled water (100 g LÀ1) was lower than that of great northern bean albumin (180 g LÀ1) (Sathe & Salunkhe, 1981) and kidney bean albumin (160 g LÀ1) (Mundi & Aluko, 2012) Gel formation from protein solution depends on different interactions between protein molecules including hydrophobic and electrostatic Figure Effects of pH and NaCl concentration on emulsifying capacity and stability of rambutan seed albumin concentrate (Results were average of three replicate Ỉ standard deviation) interactions, hydrogen bonds and disulphide bonds formed from the released thiol groups during protein gelation (Belitz et al., 2009) It can be noted that the total and free sulfhydryl contents in RSAC (Table 1) were higher than those in kidney bean albumin (4.60 and 2.20 lmol gÀ1) and that could improve the gelation Based on the LGC as index of gelation, it can be predicted that RSAC was a potential gelating protein ingredient in food industry The lowest LGC was noted for pH at which the protein solubility was minimum Similar result was reported for African locust bean albumin (Lawal et al., 2005) In the isoelectric region, minimal electrostatic repulsion promoted the formation of the necessary intermolecular forces between the protein molecules and resulted in better gelation At pH and 10, the LGC increased probably due to increased electrostatic repulsion between the protein molecules As the salt concentration varied from 0.4 to 0.6 mol LÀ1, the LGC of RSAC significantly decreased The LGC in salt solution of 0.6 mol LÀ1 was times lower Table Effects of pH and NaCl concentration on least gelation concentrations (LGC) of rambutan seed albumin concentrate (n = 3) pH LGC (g LÀ1) NaCl concentration (mol LÀ1) LGC (g LÀ1) 80 Æ 0.0 100 Æ 60 Æ 0.2 100 Ỉ International Journal of Food Science and Technology 2016 60 Ỉ 0.4 40 Ỉ 100 Ỉ 0.6 20 Ỉ 100 Ỉ 0.8 100 Ỉ 10 100 Ỉ 1.0 100 ặ â 2016 Institute of Food Science and Technology Effects of pH and salt concentration H T H Vuong et al than that in distilled water That was due to moderate increase in ionic strength which enhanced interaction between charged macromolecules (Belitz et al., 2009) Lawal et al (2005) also concluded that the LGC of African locust albumin in NaCl solution of 0.4 mol LÀ1 was 33% lower than that in distilled water However, at high salt concentration, the LGC augmented due to shielding effect on the protein molecules This phenomenon enhanced salting-out and reduced gelation capacity of the protein Conclusion RSAC showed high surface hydrophobicity which favoured its emulsifying and foaming properties Moreover, gelation capacity was one of the outstanding properties of RSAC due to high sulfhydryl content The adjustment of pH or the addition of sodium chloride improved various functional properties of the protein RSAC was a potential protein ingredient for formulation of new food products Acknowledgment This research is funded by Vietnam National University – Ho Chi Minh City (VNU-HCM) under grant number B2014-20-08 References Adebiyi, A.P & Aluko, R.E (2011) Functional properties of protein fractions obtained from commercial yellow field pea (Pisum sativum L.) seed protein isolate Food Chemistry, 128, 902–908 Augustin, M & Chua, B (1988) Composition of rambutan seeds Pertanika, 11, 211–215 Belitz, H.D., Grosch, W & Schieberle, P (2009) Food Chemistry Berlin: Springer Berlin Heidelberg Bradstreet, R.B (1965) The Kjeldahl Method for Organic Nitrogen USA: Academic Press Inc Chandi, G.K & Sogi, D.S (2007) Functional properties of rice bran protein concentrates Journal of Food Engineering, 79, 592–597 Chau, C.F., Cheung, P.C.K & Wong, Y.S (1997) Functional properties of protein concentrates from three chinese indigenous legume seeds Journal of Agricultural and Food Chemistry, 45, 2500–2503 Day, L (2013) Proteins from land plants – Potential resources for human nutrition and food security Trends in Food Science & Technology, 32, 25–42 Deng, Q., Wang, L., Wei, F et al (2011) Functional properties of protein isolates, globulin and albumin extracted from Ginkgo biloba seeds Food Chemistry, 124, 1458–1465 DuBois, M., Gilles, K.A., Hamilton, J.K., Rebers, P.A & Smith, F (1956) Colorimetric method for determination of sugars and related substances Analytical Chemistry, 28, 350–356 El-Adawy, T.A (2000) Functional properties and nutritional quality of acetylated and succinylated mung bean protein isolate Food Chemistry, 70, 83–91 Fabian, C & Ju, Y.-H (2011) A review on rice bran protein: its properties and extraction methods Critical Reviews in Food Science and Nutrition, 51, 816–827 Helrich, K (1990) Official Methods of Analysis of the AOAC, Volume Arlington, TX: Association of Official Analytical Chemists Inc © 2016 Institute of Food Science and Technology Idouraine, A., Yensen, S.B & Weber, C.W (1991) Tepary bean flour, albumin and globulin fractions functional properties compared with soy protein isolate Journal of Food Science, 56, 1316–1318 Kato, A & Nakai, S (1980) Hydrophobicity determined by a fluorescence probe method and its correlation with surface properties of proteins BBA – Protein Structure, 624, 13–20 Kinsella, J.E & Melachouris, N (1976) Functional properties of proteins in foods: a survey Critical Reviews in Food Science and Nutrition, 7, 219–280 Lawal, O.S., Adebowale, K.O., Ogunsanwo, B.M., Sosanwo, O.A & Bankole, S.A (2005) On the functional properties of globulin and albumin protein fractions and flours of African locust bean (Parkia biglobossa) Food Chemistry, 92, 681–691 Lu, B.-Y., Quillien, L & Popineau, Y (2000) Foaming and emulsifying properties of pea albumin fractions and partial characterisation of surface-active components Journal of the Science of Food and Agriculture, 80, 1964–1972 Ma, C.Y & Harwalkar, V.R (1984) Chemical characterization and functionality assessment of oat protein fractions Journal of Agricultural and Food Chemistry, 32, 144–149 Mao, X & Hua, Y (2012) Composition, structure and functional properties of protein concentrates and isolates produced from walnut (Juglans regia L.) International Journal of Molecular Sciences, 13, 1561–1581 Miller, G.L (1959) Use of dinitrosalicylic acid reagent for determination of reducing sugar Analytical Chemistry, 31, 426–428 Mundi, S & Aluko, R.E (2012) Physicochemical and functional properties of kidney bean albumin and globulin protein fractions Food Research International, 48, 299–306 Pearce, K.N & Kinsella, J.E (1978) Emulsifying properties of proteins: evaluation of a turbidimetric technique Journal of Agricultural and Food Chemistry, 26, 716–723 Ragab, D.M., Babiker, E.E & Eltinay, A.H (2004) Fractionation, solubility and functional properties of cowpea (Vigna unguiculata) proteins as affected by pH and/or salt concentration Food Chemistry, 84, 207–212 Rezig, L., Riaublanc, A., Chouaibi, M., Gueguen, J & Hamdi, S (2016) Functional properties of protein fractions obtained from pumpkin (Cucurbita maxima) seed International Journal of Food Properties, 19, 172–186 Sathe, S.K & Salunkhe, D.K (1981) Functional properties of the great northern bean (Phaseolus vulgaris L.) proteins: emulsion, foaming, viscosity, and gelation properties Journal of Food Science, 46, 71–81 Singleton, V.L & Rossi, J.A (1965) Colorimetry of total phenolics with phosphomolybdic-phosphotungstic acid reagents American Journal of Enology and Viticulture, 16, 144–158 Sirisompong, W., Jirapakkul, W & Klinkesorn, U (2011) Response surface optimization and characteristics of rambutan (Nephelium lappaceum L.) kernel fat by hexane extraction LWT-Food Science and Technology, 44, 1946–1951 Solıs-Fuentes, J.A., Camey-Ortız, G., Hernandez-Medel, M.d.R., Perez-Mendoza, F & Duran-de-Baz ua, C (2010) Composition, phase behavior and thermal stability of natural edible fat from rambutan (Nephelium lappaceum L.) seed Bioresource Technology, 101, 799–803 Thannhauser, T.W., Konishi, Y & Scheraga, H.A (1987) Analysis for disulfide bonds in peptides and proteins Methods in Enzymology, 143, 115–119 T€ om€ osk€ ozi, S., Lasztity, R., S€ ule, E., Gaugecz, J & Varga, J (1998) Functional properties of native and modified wheat germ protein isolates and fractions Food/Nahrung, 42, 245–247 Yada, R.Y (2004) Proteins in Food Processing Boca Raton, FL: Woodhead Publishing Yuliana, M., Truong, C.T., Huynh, L.H., Ho, Q.P & Ju, Y.-H (2014) Isolation and characterization of protein isolated from defatted cashew nut shell: influence of pH and NaCl on solubility and functional properties LWT - Food Science and Technology, 55, 621–626 International Journal of Food Science and Technology 2016 1219 ... The LGC in salt solution of 0.6 mol LÀ1 was times lower Table Effects of pH and NaCl concentration on least gelation concentrations (LGC) of rambutan seed albumin concentrate (n = 3) pH LGC (g... hydrophobic and electrostatic Figure Effects of pH and NaCl concentration on emulsifying capacity and stability of rambutan seed albumin concentrate (Results were average of three replicate Ỉ standard... pH and NaCl concentration on water absorption capacity of rambutan seed albumin concentrate (Results were average of three replicate Æ standard deviation) cake batters, mayonnaise and salad dressings