Nghệ Thuật Gấp Giấy_ Gấp 1 CHIẾC XE MÁY VMAX PAPER CRAFT_ YAMAHA rất đẹp trong mắt người bạn yêu thương. file dạng pdf hướng dẫn rất cụ thể, tỉ mỉ và chỉ dẫn các cách để bạn cắt và gấp giấy
PAPER CRAFT Assembly Instructions Thank you for downloading the "VMAX" paper craft model By simply following this manual while referring to the names and numbers shown on the parts sheets, you can assemble an authentic-looking replica of the VMAX Assembly instructions: Fifteen A4-sized sheets Paper craft: Sixteen A4-sized sheets with 174 parts in all These instructions apply only to the "VMAX" Other paper craft model instructions can be downloaded separately The parts are easier to work with when printed on strong, thick paper Note Basic working method and markings TO BEGIN Tools and materials needed Solid lines -Ruler -Scissors - Blade cutter or "Exacto-knife" - Awl or other pointed tool (for making a folding crease) - Felt pen - Pin set - Glue - Hand towel ( for cleaning your fingers) - Dictionary or other heavy book ( to press the papers flat) Fold along these lines The printed surface should be on the outside of the folded shape Broken lines Item of Caution *Take care when using sharp or pointed objects or when using bladed cutting tools Place a heavy sheet of paper under the paper you want to cut *Use glue and other adhesives only in well-ventilated areas *When printing, use a slightly reduced font size as there are many differences in dimensions depending on the type of printer used Fold along these lines The printed surface should be on the inside of the folded shape Dotted line Cut along these lines HOW TO ASSEMBLE Do not fold or cut the parts marked *Follow the working method and markings carefully *Cut carefully along the outter line with a cutting blade, Exacto-knife or scissors One - point Advice Cut out parts marked with an asterisk (*) *Cut carefully with a cutting blade, Exacto-knife or scissors *For folding parts, first use an awl or other pointed tool to make a light crease along the dotted or solid line This will make the folds straight Avoid making strong creases, as this will cause the paper to tear Red dots are the reference positions for gluing surfaces *As an adhesive, white, wood glue is recommended Avoid over application as this will cause the paper to wrinkle *Before beginning assembly, test adhesive amounts on extra paper *Occasionally, white spots will be apparent on folds and cuts Use a marker or pencil to fill-in these spots It is recommended that this be done after each stage of assembly because coloring becomes more difficult once parts are assembled -2- Assembling the Body First, assemble each component by following the working method and markings Then, refer to the illustration and photos below to glue the parts together Body Sheet A, part in total Indication of Working Methods Fold or Curve Fold each relevant part according to the assembly symbols A-1 Reference photo -3- Glue Assembling the Steering Column First, assemble each component by following the working method and markings Then, refer to the illustration and photos below to glue the parts together Indication of Working Methods Fold or Curve Steering column Fold each relevant part according to the assembly symbols Sheet B, 24 parts in total Please use the Glue dots on each component as reference when gluing surfaces B-3 B-4 B-9 B-5 B-6 B-13 B-1 B-12 B-10 B-7 B-14 B-11 B-2 B-24 B-8 Reference photo B-15 B-23 B-20 B-16 B-17 B-18 B-22 B-19 B-21 Apply glue on the area indicated in the illustration -4- Assembling the Top Cover and Intake First, assemble each component by following the working method and markings Then, refer to the illustration and photos below to glue the parts together Indication of Working Methods Glue Fold or Curve Top cover Fold each relevant part according to the assembly symbols Sheet C, parts in total Please use the dots on each component as reference when gluing surfaces C-1 C-2 C-2 Reference photo Fold and glue the parts making sure both tabs (illustrated by dotted-lines) are neatly tucked in Intake Sheet D, parts in total D-2 Fold each relevant part according to the assembly symbols D-1 -5- Reference photo Assembling the Engine First, assemble each component by following the working method and markings Then, refer to the illustration and photos below to glue the parts together Indication of Working Methods Glue Fold or Curve Engine Fold each relevant part according to the assembly symbols Sheet E, 47 parts in total Please use the dots on each component as reference when gluing surfaces E-29 (E-31) E-28 (E-30) E-33 (E-35) E-44 (E-45) E-32 (E-34) E-8 (E-14) E-12 (E-10) E-36 (E-38) E-11 (E-9) E-41 (E-43) E-7 (E-13) E-17 (E-18) E-24 (E-27) E-37 (E-39) E-1 (E-2) E-21 (E-22) E-15 (E-16) E-40 (E-42) E-26 (E-25) E-46 (E-47) E-20 (E-19) E-5 (E-6) E-3 (E-4) E-23 * Only the left part is available Reference photo Left * Make two of each part The diagram shows how the left part of the engine looks The numbers within parentheses indicate parts for the right part of the engine Right -6- Assembling the Side Covers First, assemble each component by following the working method and markings Then, refer to the illustration and photos below to glue the parts together Indication of Working Methods Fold or Curve Side covers Fold each relevant part according to the assembly symbols Sheet F, 20 parts in total Please use the Glue dots on each component as reference when gluing surfaces * Make two of each part The diagram shows how the left frame cover looks The numbers within the parentheses indicate parts for the right frame cover F-5 (F-12) F-1 (F-8) F-4 (F-11) F-19 (F-20) F-2 (F-9) F-7 (F-14) F-17 (F-18) F-3 (F-10) F-6 (F-13) F-15 (F-16) Reference photo Right Left -7- Assembling the Exhaust First, assemble each component by following the working method and markings Then, refer to the illustration and photos below to glue the parts together Indication of Working Methods Glue Fold or Curve Exhaust Fold each relevant part according to the assembly symbols Sheet G, 23 parts in total Please use the dots on each component as reference when gluing surfaces in the diagram indicate where parts are to be glued later Please not glue parts at this stage G-14 G-15 To the right side of the engine G-22 G-16 G-20 G-17 G-4 G-18 G-21 G-1 G-2 G-5 G-19 G-3 G-23 G-8 G-13 G-7 G-6 When gluing each part, make sure the angle is correct, referring to the photo below G-12 To the left side of the engine G-11 G-9 G-10 Reference photo Exhaust A Exhaust B Partition of exhaust pipes - Exhaust A (Right) G-1 to G-4 - Exhaust A (Left) G-5 to G-8 - Exhaust B (Right) G-14 to G-18 - Exhaust B (Left) G-9 to G-13 - Exhaust pipe C G-19 to G-23 Exhaust C -8- Assembling the Radiator and Rear Suspensions First, assemble each component by following the working method and markings Then, refer to the illustration and photos below to glue the parts together Indication of Working Methods Fold or Curve Radiator Fold each relevant part according to the assembly symbols Sheet H, parts in total Please use the Glue dots on each component as reference when gluing surfaces H-3 H-2 Reference photo H-1 Rear suspensions Fold each relevant part according to the assembly symbols Sheet I, parts in total Please use the dots on each component as reference when gluing surfaces * Make two of the rear suspensions They should be identical The numbers within the parentheses indicate the parts for the second suspension I-3 (I-4) Reference photo I-5 (I-6) I-1 (I-2) I-7 (I-8) Apply glue on the area indicated in the illustration -9- Assembling the Rear Fender and Seat First, assemble each component by following the working method and markings Then, refer to the illustration and photos below to glue the parts together Indication of Working Methods Glue Fold or Curve Rear fender Fold each relevant part according to the assembly symbols Sheet J, parts in total Please use the dots on each component as reference when gluing surfaces J-2 Reference photo J-1 J-3 Seat Fold each relevant part according to the assembly symbols Sheet K, parts in total Please use the dots on each component as reference when gluing surfaces K-1 K-5 K-3 K-2 K-4 K-6 K-8 K-9 K-7 - 10 - Reference photo Assembling the Front Tire First, assemble each component by following the working method and markings Then, refer to the illustration and photos below to glue the parts together Indication of Working Methods Fold or Curve Front tire Fold each relevant part according to the assembly symbols Sheet L, 13 parts in total Please use the Glue dots on each component as reference when gluing surfaces L-2 L-4 L-13 L-7 L-10 L-11 L-5 L-9 L-8 L-6 L-12 L-3 L-1 Reference photo - 11 - 10 Assembling the Rear Tire First, assemble each component by following the working method and markings Then, refer to the illustration and photos below to glue the parts together Indication of Working Methods Fold or Curve Rear tire Fold each relevant part according to the assembly symbols Sheet M, 19 parts in total Please use the Glue dots on each component as reference when gluing surfaces Reference photo *Glue the completed rear arm to the assembled rear tire [Rear tire] M-8 M-9 M-6 M-11 M-3 M-4 M-12 [Rear arm] M-18 To the rear tire M-17 M-2 M-1 M-10 M-16 M-19 M-1 M-5 To the rear arm M-15 M-13 - 12 - 11 Finish Please use the dots on each component as reference when gluing surfaces Side cover (Right) Top cover Assembly Instructions Side cover (Left) Seat Rear fender Intake (Right) glue the assembled parts in numerical order through Rear suspensions Engine (Right) Glue the right and left parts of the engine to the body Glue the right and left parts of the intake to the body To the Right intake To the right frame cover Glue the rear tire to the body Glue the right and left side covers to the body Glue the rear fender to the right and left frame covers Glue the right and left rear suspensions to the rear tire and the right and left side covers Glue exhaust C to the rear tire Insert the right and left exhaust B into the engine After inserting the right and left exhaust A into the engine, insert exhaust pipes A and B into exhaust C Glue the seat to the body Body Rear tire Glue the fuel top cover to the body and seat Engine (Left) Glue the radiator to the body Glue the front tire to the steering column Glue the part completed in Intake (Left) to the body To the Right engine Steering column Front tire Exhaust C Exhaust B Radiator Exhaust A - 13 - 12 Assembled Model and the List of Parts Please refer to the photo below when attaching each component FRONT RIGHT Engine (Right) Top cover Side cover (Right) F-8 F-9 F-1 F-1 F-1 F-1 F-1 F-1 F-1 F-2 Intake (Right) C-1 C-2 D-2 E-2 E-4 E-6 E-9 E-1 E-1 E-1 Body A-1 E-1 E-1 E-1 E-2 E-2 E-2 E-3 E-3 E-4 E-3 E-4 E-3 E-3 E-3 E-4 E-4 Steering column Exhaust Rear suspension (Right) I-2 I-6 I-4 I-8 Front tire G-1 G-2 G-3 G-4 G-5 G-6 L-1 L-2 L-3 L-4 L-5 G-7 G-8 G-9 G-1 G-1 G-1 G-1 G-1 G-1 G-1 G-1 G-1 G-1 G-2 G-2 G-2 G-2 - 14 - L-6 L-1 L-7 L-1 L-8 L-1 L-9 L-1 B-1 B-2 B-3 B-4 B-5 B-6 B-7 B-8 B-9 B-1 B-1 B-1 B-1 B-1 B-1 B-2 B-1 B-2 B-1 B-2 B-1 B-1 B-2 B-2 12 Assembled Model and the List of Parts Please refer to the photo below when attaching each component REAR LEFT Seat K-1 K-2 K-3 K-4 K-5 Intake (Left) D-1 Rear fender K-6 K-7 K-8 K-9 J-1 J-2 J-3 Radiator H-1 H-2 H-3 Rear suspension (Left) I-1 I-3 I-5 I-7 Engine (Left) E-1 E-3 E-5 E-7 E-8 E-1 E-1 E-1 E-1 E-2 E-2 E-2 Side cover (Left) E-2 E-2 E-2 E-2 E-3 E-3 E-3 E-3 E-4 E-4 E-4 E-4 Rear tire F-1 F-4 F-7 F-1 F-2 F-5 F-1 F-3 F-6 F-1 M-1 M-2 M-3 M-4 M-5 - 15 - M-6 M-7 M-8 M-9 M-1 M-1 M-1 M-1 M-1 M-1 M-1 M-1 M-1 M-1 ... I-2 I-6 I-4 I-8 Front tire G -1 G-2 G-3 G-4 G-5 G-6 L -1 L-2 L-3 L-4 L-5 G-7 G-8 G-9 G -1 G -1 G -1 G -1 G -1 G -1 G -1 G -1 G -1 G -1 G-2 G-2 G-2 G-2 - 14 - L-6 L -1 L-7 L -1 L-8 L -1 L-9 L -1 B -1 B-2 B-3 B-4... E-2 E-2 Side cover (Left) E-2 E-2 E-2 E-2 E-3 E-3 E-3 E-3 E-4 E-4 E-4 E-4 Rear tire F -1 F-4 F-7 F -1 F-2 F-5 F -1 F-3 F-6 F -1 M -1 M-2 M-3 M-4 M-5 - 15 - M-6 M-7 M-8 M-9 M -1 M -1 M -1 M -1 M -1 M -1 . .. E-29 (E- 31) E-28 (E-30) E-33 (E-35) E-44 (E-45) E-32 (E-34) E-8 (E -1 4 ) E -1 2 (E -1 0 ) E-36 (E-38) E -1 1 (E-9) E- 41 (E-43) E-7 (E -1 3 ) E -1 7 (E -1 8 ) E-24 (E-27) E-37 (E-39) E -1 (E-2) E- 21 (E-22) E -1 5