Next-Generation PON Evolution Next-Generation PON Evolution Overview .1 PON Evolution .2 2.1 Basic Principles 2.2 Evolution Path .2 Smooth Evolution Based on Coexistence: NG-PON1 .4 3.1 Network Architecture, Coexistence and Evolution 3.2 Physical Layer Specifications 3.3 TC Layer Specifications 3.4 Management and Configuration 3.5 Interoperability 11 A Brand New Technology for Long-Term Evolution–NG-PON2 .12 4.1 WDM-PON 12 4.2 ODSM-PON 14 4.3 Stacked XG-PON 15 4.4 Coherent WDM-PON 15 4.5 Other Technologies 16 The Evolution of PON Technology and Networks 17 5.1 Bandwidth Requirement Drives NG PON Evolution 17 5.2 Industry Chain Drives NG PON Evolution 18 5.2.1 NG PON Cost 18 5.2.2 OLT Capability .20 Overview A passive optical network (PON) features a point-to-multi-point (P2MP) architecture to provide broadband access The P2MP architecture has become the most popular solution for FTTx deployment among operators PON-based FTTx has been widely deployed ever since 2004 when ITU-T Study Group 15 Q2 completed recommendations that defined GPON system [ITU-T series G.984] As full services are provisioned by the massive deployment of PON networks worldwide, operators expect more from PONs These include improved bandwidths and service support capabilities as well as enhanced performance of access nodes and supportive equipment over their existing PON networks The direction of PON evolution is a key issue for the telecom industry Full Service Access Network (FSAN) and ITU-T are the PON interest group and standard organization, respectively In their view, the next-generation PONs are divided into two phases: NG-PON1 and NG-PON2 Mid-term upgrades in PON networks are defined as NG-PON1, while NG-PON2 is a long-term solution in PON evolution Major requirements of NG-PON1 are the coexistence with the deployed GPON systems and the reuse of outside plant The aforementioned requirements were tested in the recent Verizon field trials Optical distribution networks (ODNs) account for 70% of the total investments in deploying PONs Therefore, it is crucial for the NGPON evolution to be compatible with the deployed networks With the specification of system coexistence and ODN reuse, the only hold-up of the migration from GPON to NG-PON1 is the maturity of the industry chain Unlike NG-PON1 that has clear goals and emerging developments, there are many candidate technologies for NG-PON2 The selection of NG-PON2 is under discussion However, one thing is clear, NG-PON2 technology must outperform NG-PON1 technologies in terms of ODN compatibility, bandwidth, capacity, and cost-efficiency This paper describes the design principles and prospective technologies for NG-PONs It introduces Huawei’s views of NG-PON evolution, focusing on the discussion and evaluation of various technologies All of the discussion follows the FSAN and ITU-T framework of NG-PON recommendations PON Evolution 2.1 Basic Principles Ultra broadband and co-existence with existing technologies are the general requirements from network operations to direct PON evolution Operators worldwide are seeking to increase revenue by developing bandwidth-consuming services An exemplified service is HDTV, which requires about 20 Mbit/s per channel In the near future, new business models, such as home video editing, online gaming, interactive E-learning, remote medical services, and next-generation 3D TV will dramatically increase bandwidth demand The deployment of PON generally implies considerablely initial investments and slow return on investment (ROI) ODN deployment accounts for 76% of the total investments in greenfield FTTH networks, while optical network units (ONUs) account for 21% Protecting investments by leveraging existing ODNs is essential to operators 2.2 Evolution Path After GPON Recommendations were done, FSAN and ITU-T continued the study of NG-PONs and defined the first phase of NG-PONs as systems that offer low costs, large capacity, wide coverage, full service, and interoperability with existing technology FSAN and ITU-T members also agree that longterm PON evolution will be driven by new scenarios if coexistence with legacy systems is not required In addition to time-division multiplexing (TDM) PONs, other technologies for NG-PON could also be taken into account Based on the current application demands and technological maturity, FSAN divides NG-PONs into two phases shown in Figure 2-1 As indicated in Figure 1, FSAN divide NG-PON evolution into NG-PON1 and NG-PON2 NG-PON1 is a mid-term upgrade, which is compatible with legacy GPON ODNs NG-PON2 is a long-term solution in PON evolution that can be deployed over new ODNs, independent of GPON standards The selection of NG-PON1in FSAN is a trade-off between technology and cost Operators require that NG-PON1 systems have a higher capacity, longer reach, larger bandwidth, and more users Operators also require that Figure 2-1 NG-PON roadmap by FSAN Current work focus: Selecting the most suitable Technology for NG-PON2 Downstream: 10G Upstream: 2.5G or 5G Coexistence need not be considered Downstream: 2.5G Upstream: 1.25G XG-PON1 WDM coexistence NG-PON2 ODSM, 40G, WDM, OFDMA…… G-PON 2004 2010 ~2015 NG-PON1 should leverage the use of existing GPON ODN to control cost Moreover, driven by services, the downstream bandwidth demands will outpace upstream bandwidth demands for a long period Therefore, FSAN decided to define NG-PON1 as an asymmetric 10G system with rates of 10G downstream and 2.5G upstream The selected NG-PON1 system is essentially an enhanced TDM PON from GPON Unlike NG-PON1, there are several types of prospective technologies that can be adopted for NG-PON2 Among the prospective technologies, a suggested baseline is to improve the rate to 40G from 10G by following the TDM technology The second method is the employment of wavelength division multiplexing (WDM) PON to achieve 40G access The possible multiplexing schemes can be coarse wavelength division multiplexing (CWDM) or dense wavelength division multiplexing (DWDM) The ODSM PON topology based on TDMA+WDMA is also suggested, which dynamically manages user spectrum without modifying the ODN and ONUs The third prospect is OCDMA-PON OCDMA-PON uses code division multiple access (CDMA) to encode ONU singals, thereby avoiding the timeslot assignment for data transmission required by a time division multiple access (TDMA) systems The O-OFDMA PON topology is an option that uses orthogonal frequency division multiple access (OFDMA) technology to differentiate ONUs, thus effectively improving bandwidth usage However, most of these technologies are still in the research phase More study and test are highly desired to promote them as industry standard 3 Smooth Evolution Based on Coexistence: NG-PON1 A general requirement of NG-PON1 is to provide higher data transmission rates than GPON In addition, operators expect NG-PON1 to leverage existing optical deployments Hence, FSAN and ITU-T specified the NG-PON1 backward compatibility with legacy GPON deployments to protect the initial GPON investments of operators The specified NG-PON1 system is called XG-PON1 In an XG-PON1 system, the upstream rate is 2.5G and the downstream rate is 10G Therefore, the downstream bandwidth of XG-PON1 is four times of that of GPON, while the upstream bandwidth of XG-PON1 is twice as that of GPON Particularly, the ODN in XG-PON1 entirely inherits that of GPON, implying that optical fibers and splitters in legacy GPON systems can be reused in XG-PON1 After a 10G interface board is added to the OLT, smooth evolution from GPON to XGPON1 can be achieved, which completely leverages the value of GPON ODN Figure 3-1 XG-PON1 standardization developments Completed G.987.RE draft Started G.987.RE Standarization developments Completed major architecture Completed extended power budget specifications Revised jitter parameters 200906 Completed G.987.3 draft (edition one) and stabilized G.988 Completed G.987.3 Completed the G.988 draft (edition one) Discussed G.987.3/G.988 Technical specifications Wrote and revised G.987/ G.987.1/G.987.2 Completed scrambling and security specifications Completed framing specifications Completed and published G.987/G.987.1/G.987.2 200910 Further revised G.987.2 Beijing FSAN/Q2 201002 Completed G.987.3/G.988 Started enhanced XG-PON1 Principal standards Completed G.987.2 revision Completed principal XG-PON1 standards To publish principal XG-PON1 standards 201006 201008 As an enhancement to GPON, XG-PON1 inherits the framing and management from GPON XG-PON1 provides full-service operations via higher rate and larger split to support a flattened PON network structure The baseline XG-PON1 standards have been completed In October 2009, ITU-T consented general requirements and physical layer specifications of XG-PON1 and published them in March 2010, announcing the NG-PON era In June 2010, the transmission convergence (TC) layer and optical network termination management and control interface (OMCI) standards for XGPON1 were consented in the general meeting of ITU-T SG15, and these standards will be published soon Figure 3-1 shows the XG-PON1 standardization developments 3.1 Network Architecture, Coexistence and Evolution XG-PON1 is an enhancement to GPON It inherits the point-to-multipoint (P2MP) architecture of GPON and is able to support diverse access scenarios, such as fiber to the home (FTTH), fiber to the cell (FTTCell), fiber to the building (FTTB), fiber to the curb (FTTCurb), and fiber to the cabinet (FTTCabinet) The application scenarios of XG-PON1 are shown in Figure 3-2 Figure 3-2 XG-PON1 application scenarios XG-PON Cell site FTTCell CBU Business FTTB MTU FTTO XG-PON OLT SBU FTTH Residential FTTB FTTCurb/Cab Aggregation Switch SFU XG-PON OLT MDU ONU XG-PON1 coexists with GPON over the same ODN, thereby protecting the investments of operators on GPON As indicated in XG-PON1 physical layer specifications, the upstream/downstream wavelength of XG-PON1 is different from that of GPON Compatibility between XG-PON1 and GPON is achieved by implementing WDM in the downstream and WDMA in the upstream That is, a WDM1r is deployed at the central office (CO) and a WBF is deployed at the user side (could be located inside an ONU, between an ONU and an optical splitter, or on an optical splitter) to multiplex or demultiplex wavelengths on multiple signals in downstream and upstream directions The coexistence of GPON and XG-PON1 is shown in Figure 3-3 FSAN and ITU-T have proposed two evolution scenarios to greenfield and Brownfield Greenfield scenarios not have any pre-existing optical fiber deployments Hence, these scenarios can use XG-PON1 to replace legacy copper line systems Greenfield scenarios require the deployment of new PON systems, which are straight-forward; therefore, this paper does not describe it in detail Figure 3-3 XG-PON1 & GPON coexistence by WDM1r Logic Tx Rx WBF WDM -X-L WBF V-Rx WBF-V IF GPON WDM-X’ Tx WBF Logic WDM-G IF Video OLT (video) Tx Rx WBF V-Rx WBF-V WDM-G’ V-Tx ODN WDM -G-L Tx IF GPON, IF Video ONU (G-PON + video) Logic WDM1r IF GPON ONU (G-PON) Rx OLT (G-PON) Rx Splitter Logic Logic Tx Tx Rx OLT (XG-PON) Rx WDM-X IF XGPON, IF Video ONU (XG-PON + video) Logic IF XGPON IF XGPON ONU (XG-PON) WBF Brownfield scenarios (that is, coexistence with existing deployments) use the pre-existing GPON deployments of operators As the bandwidth requirement increases, operators can upgrade ONUs over the ODN batch by batch or all at once when migrating to XG-PON1 The selection between these two types of upgrades is decided by how long GPON and XG-PON1 will be coexist in the same ODN To achieve a successful GPON-to-XG-PON1 upgrade, the OLT and each ONU must support [ITU-T G.984.5 AMD 1] compliant wavelength plans Figure 3-4 shows coexistence of GPON and XG-PON1 using WDM stacking Figure 3-4 GPON & XG-PON1 coexistence using WDM stacking Key technology: WDM stacking ONU XG-PON1 OLT ONU ONU WDMr1 ONU ONU ONU ONU G-PON1 OLT GPON and XGPON1 use the same 1:32 optical splitter for optical splitting Every GPON user enjoys a bandwidth of about 80 Mbit/s (downstream)/40 Mbit/s (upstream) and every XGPON1 user enjoys a bandwidth of about 320 Mbit/s (downstream)/80 Mbit/s (upstream) 3.2 Physical Layer Specifications XG-PON1 physical layer specifications were finalized in October 2009 and published by ITU-T in March 2010 Table 3-1 lists the detailed specifications for XG-PON1 [1] XG-PON1wavelength plan was a hot topic discussed in FSAN by vendors as well as operators Driven by the 10G optical transceivers market, FSAN selected the downstream wavelength of 1575–1580 nm to promote the technology maturity Table 3-1 XG-PON1 physical layer specifications Item Specifications Optical fiber Compliant with [ITU-T G.652] New optical fibers that are compliant with [ITU-T G.657] are applicable to XG-PON1 deployments Wavelength plan [1] Upstream: 1260 to1280 nm Downstream: 1575 to 1580 nm Downstream: 1575 to 1581 nm (for outdoor deployments) Power budget N1: 14 to 29 dB (for applications that are not co-existent) N2: 16 to 31 dB (used for applications that are coexistent; these figures include WDM1r insertion loss) Extra budget: minimum of 33 dB, scalable to 35 dB) Line rate [2] Upstream: 2.48832 Gbps Downstream: 9.95328 Gbps Split ratio At least 1:64 Scalable to 1:128 and 1:256 Maximum physical transmission reach At least 20 km Maximum logical transmission reach At least 60 km Maximum differential logical reach Scalable to 40 km C band L band, and O band were compared in the selection of upstream wavelength The first option of C band was eliminated because it overlaps with for the RF video channel The L band was also eliminated due to the insufficient guard band between upstream and downstream wavelengths The candidate wavelength was narrowed down to O- band and O+ band After comparing the pros and cons (such as complexity and costs), O- band was selected because O+ band has higher requirements on filters [2] The downstream rate of XG-PON1 was specified to 10 Gbps, which was driven by the well-established and low-cost 10 Gbps continuous transmission technology in the industry The exact rate is determined as 9.95328 Gbps to keep the consistency with typical ITU-T rates This is different from the rate of the IEEE 10GE-PON, which is in the rate of 10.3125 Gbps There were 2.5G and 10G proposals for the XG-PON1 upstream rate After carefully studying application scenarios and component cost, 2.5G upstream rate was selected for specification The 10G upstream system was not considered as the focus, mainly due to its high cost and limited application scenarios in the near future Remarks 3.3 TC Layer Specifications The XG-PON1 transmission convergence (XGTC) layer optimizes the basic processing mechanisms of the GPON TC layer by enhancing the framing structure, dynamic bandwidth assignment (DBA), and activation mechanisms XG-PON1 enhances the GPON framing by aligning the frame and field design to word boundaries This framing structure matches the rate of XGPON1 It is easy to implement with chips, and improves the efficiency of data fragmentation, reassembling, and processing The DBA mechanism in XG-PON1 is basically upgraded by offering better flexibility The activation mechanism of XG-PON1 follows the principles of GPON Improved security and power saving are the two major features of the XGTC layer In GPON, data encryption is optional and security related management is facilitated via OMCI In XG-PON1, operators require enhanced security from the very initial procedure of PON activation XG-PON1 standards specify three methods of authentication The first is an ONU authentication scheme based on a registration ID (a logical ID used for authentication) The second method is a bidirectional authentication scheme based on OMCI channels (inherited from GPON) The third method is a new bidirectional authentication scheme based on IEEE 802.1x protocols The XGTC layer also provides new security mechanisms, such as upstream encryption and downstream multicast encryption Power saving in GPON was an afterward thought The ITU-T published [G.sup45] on saving power with multiple modes at the chip level Operators propose mandatory regulations and improvements on XG-PON1 to promote power saving worldwide XG-PON1 supports doze mode and cyclic sleep mode specified in [G.sup45] Vendors are also allowed to independently extend power saving techniques The draft of XGTC layer standard was completed in April 2010 The ITU-T Recommendation [G.987.3], aka: the XG-PON1 TC layer standard was officially approved in June 2010 3.4 Management and Configuration The management and configuration of XG-PON1 should not be impacted by the changes of lower-layer technologies Therefore, ITU-T Recommendation [G.984.4] was adopted as the baseline for standard development This further facilitates backward compatibility with GPON and minimizing of changes OMCI management is a management mechanism in GPON that carries OMCI data over a special GEM connection The special GEM connection is also called an OMCI channel An OLT manages and configures ONUs through the OMCI channel The OLT and the ONU exchange management information base (MIB) information to establish and maintain an OMCI model OMCI management and configuration covers configuration management, fault management, performance management, and security management of the ONUs XG-PON1 inherits almost 90% of the GPON OMCI technology with minor modifications to [G.984.4] Consider the management and configuration of a Layer-2 data service as an example As far as the service is concerned, it does not matter which specific lower-layer technology is adopted The key point is that a Layer-2 channel should be properly configured to ensure normal forwarding of service data The OMCI L2 model covers all possible L2 configurations from the network side to the user side (ANI-TCONT-GEM-MAC bridge-UNI) This model is applicable to GPON as well as to XG-PON1 because they both have the same definitions for the network-side channel and userside interface The ONU management and configuration mechanisms are pretty stable from A /B-PON to GPON and to XG-PON1 Therefore, it was decided that the ITUT's TDM PON series require only one general OMCI standard that is applicable to all PON systems This is the concept of generic OMCI, which gained wide recognition and support from the industry ITU-T/Q2 applied for an ITU-T program numbered [G.988] for the Generic OMCI Standard to distinguish the standard from the PON system The [G.988] document was developed based on the latest version of [G.984.4] The difference is that [G.988] excludes descriptions that are specifically related to the technical features of PONs In this way, [G.988] is specified to cover the general OMCI in PONs The terminal management of XG-PON1 fully retains the GPON features In the FTTH scenario, the default management of ONUs in XG-PON1 is via OMCI In the FTTB/FTTC scenario, XG-PON1 can manage ONUs through OMCI or other management protocols (i.e., dual management) The dual management mechanism is to first set up an OMCI channel, which serves as the Layer-2 channel required by other management protocols for interoperation; then, use the virtual port of the OMCI as a division point for transparently transmitting the packets of other management protocols over the PON link The flexibility of dual management enables GPON and XG-PON1 to address 10 various management requirements in different scenarios The first draft of [G.988] was completed in February 2010 In April 2010, the official draft of [G.988] was finished In June 2010, [G.988] was approved by ITU-T 3.5 Interoperability Interoperability is the most impressive feature of GPON and XG-PON1 FSAN established the OMCI implementation study group (OISG) in 2008 during the GPON era The group members were restricted to system vendors and chip vendors to study the [G.984.4] OMCI interoperability specification The [G.984.4] Recommendation defines the establishment of an ONT management and control channel (OMCC), update of the MIB after an ONU goes online, MIB/alarm synchronization, software version upgrade, L2 service configuration, multicast configuration, and QoS management The first edition of [G.984.4] was finished in December 2008 and second edition was finished in October 2009 Both editions were approved and quickly released by ITU-T The official number of [G.984.4] is [ITU-T G.impl984.4] and is also called the OMCI implementation guide Since then, FSAN has been using [G.impl984.4] as the primary specification for interoperability test cases Three interoperability tests were performed between 2009 and the first half of 2010 After the interoperability tests were completed in the first half of 2010, FSAN operators were satisfied with the test results and did press release to highlight the superb interoperability of GPON FSAN considers the GPON interoperability test has reached a remarkable milestone and the further research of this subject will be conducted in the broadband forum (BBF, the original DSL forum) FSAN will move on to the interoperability testing of XGPON1 [G.988] Recommendation basically adopts [G.impl984.4] directly Hence, the mandatory appendix of [G.988] incorporates all contents of [G.impl984.4], meaning that XG-PON1 inherits the superb interoperability of GPON 11 A Brand New Technology for Long-Term Evolution–NG-PON2 The selection of XG-PON1 is driven by technology availability and economic reasons When evolving from NG-PON1 to NG-PON2, however, more technologies are available for long-term evolution Therefore, upgrades with more intense innovations can be envisioned In the FSAN NG-PON2 workshops, items discussed include 40G, WDM PON, OFDMA, etc 4.1 WDM-PON A typical wavelength division multiplexing PON (WDM-PON) architecture is shown in Figure 4-1 The wavelength division MUX/DEMUX is employed in the ODN In the example in Figure 4-1, array waveguide gratings (AWGs) are used to MUX and DEMUX wavelengths to or from ONUs Signal transmission in WDM-PON is similar to that in the point to point GE (P2P GE) The difference between the two systems is that WDM-PON is based on the isolation of different wavelengths on the same optical fiber Each ONU in WDM-PON exclusively enjoys the bandwidth resources of a wavelength In other words, WDM-PON features a logical P2MP topology, as shown in Figure 4-2 In the WDM-PON system in Figure 4-1, each port of the AWG is wavelengthdependent, and the optical transceiver on each ONU must transmit optical signals in a specified wavelength determined by the port on the AWG Optical transceivers with specified wavelengths are called colored optical transceivers Colored optical transceivers introduce complexity in processes such as service provisioning and device storage In addition, AWG components are sensitive to temperature Therefore, WDM-PON has the following two major challenges Challenge 1: Addressing the real-time consistency between the wavelength of optical transceivers and the connecting AWG port Colorless optical source technology is used to resolve this issue Colorless optical source solutions can be classified into tunable laser and seeded laser according to whether a seed source is involved According to the source of the seed light, the solutions can be further defined as self-injection, external injection (including ASE seed light injection and array laser injection), and wavelength re-use 12 Figure 4-1 Typical WDM-PON system 用户终端 λ1, λ2, λ3, λ4 CO Tx/Rx λ1 Remote Node Tx/Rx λ2 Tx/Rx AWG2 AWG1 Tx/Rx Tx/Rx λ3 Tx/Rx Tx/Rx λ4 Tx/Rx Figure 4-2 WDM-PON network topology CO 终端用户n WDM-PON AWG AWG Rx Tx Rx Tx Rx Tx AWG Rx Tx 终端用户1 AWG Rx Tx Fiber distribution frame AWG Rx Tx Fiber distribution frame Rx Tx Rx Tx Challenge 2: Addressing the real-time consistency between the wavelengths of the port on the local AWG (at the CO) and the port on the remote AWG Wavelength alignment technology is used to resolve this issue Wavelength alignment technology includes optical power monitoring and temperatureinsensitive AWG Optical power monitoring was a solution proposed in the early stage of WDM-PON research The recent solution to wavelength alignment is the temperature-insensitive AWG technology In addition to the aforementioned issues, other challenging factors to WDMPON include the industry chain maturity, technology availability, cost, and insufficient bandwidth drive from the end users It is not anticipated to have large scale deployment of WDM-PON in FTTH scenarios in the next 3–5 years WDM-PON may, however, have fans in bandwidth-hungry and costinsensitive applications, such as FTTB/FTTbusiness and FTTMobile 13 4.2 ODSM-PON Opportunistic and dynamic spectrum management PON (ODSM-PON) was proposed a couple of years ago It addresses operator requirements in exploiting the potential of deployed networks for smooth network evolution It keeps the ODN and ONUs untouched, providing a salient solution to CO consolidation and cost control End users in ODSM-PON enjoy the new communication experience made available by optical broadband with affordable cost Figure 4-3 ODSM PON ONU ONU ONU ONU ONU ONU ODSM OLT Multi Chan MAC Tx Array Old CO WDM split Rx Array ONU ONU ONU ONU ONU ONU ONU ONU ONU ONU ONU ONU ONU ONU ONU ONU ONU ONU A solution shown in Figure 4-3 was proposed in 2010 In this solution, the four GPON/XG-PON1 OLT line cards previously deployed at the "Old CO" can be replaced with one passive WDM splitter for network upgrade The network from the CO to user premises remains unchanged after the upgrade The new ODSM OLT communicates with GPON/XG-PON1 ONUs, as demonstrated by Figure 4-3 In the downstream, ODSM-PON adopts WDM The data carried over various wavelengths transmitted by the OLT transmitter array is split by the WDM splitter and then distributed to GPON/XG-PON1 ONUs In the upstream, ODSM PON adopts dynamic TDMA+WDMA The data transmitted by the GPON/XG-PON1 ONUs is combined by the WDM splitter and then transmitted to the OLT receiver array ODSM-PON has the following features: •• Leverages the existing ODN from the CO to user premises •• Leverages the existing ONU at user premises 14 •• Cost reduction and power saving with the passive “Old CO” •• Substantially improves (by 10-fold) the fiber sharing between the CO and metro devices •• Follows GPON/XG-PON1 deployment policies by,allowing for an upgradeas-required mode ODSM PON offers a brand new choice to the industry 4.3 Stacked XG-PON Stacked XG-PON is one of the candidate technologies for NG-PON2 As shown in Figure 4-4, multiple XG-PON1 sub-networks share one ODN by using WDM Each XG-PON1 works independently on a separate wavelength pair The wavelengths can be fixed or variable Wavelength plan is the key issue for stacked XG-PON When deploying stacked XG-PON, the XG-PON1 ONUs should be replaced by colored ONUs, while the ONUs are untouched in OSDM-PON Figure 4-4 Stacked XGPON CO XGPON1 OLT WDM XGPON1 OLT XGPON1 ONT XGPON1 OLT XGPON1 ONT SP XGPON1 ONT A similar proposal of stacked G-PON technology was discussed in the FSAN NG-PON1 study period FSAN members conclude that it was more of a network deployment technology than a system required standards When the focus of the standardization was recently shifted to NG-PON2, stacked XGPON became one of the study topics once again 4.4 Coherent WDM-PON Coherent WDM-PON is also a candidate technology for NG-PON2 As shown in Figure 4-5, both OLT and ONU select wavelengths according to the principle of coherent detection This means the OLT and ONU start coherent 15 Figure 4-5 Coherent WDM-PON X Modulator X ONU OLT X X Pol Div Coh Rx DSP Local Osc Control L.O #N X X X Pol Div Coh Rx Modulator X Freq Gen reception only when the locally-oscillated light and signal light meet the coherent conditions of frequency, phase, and polarization In this way, the OLT and ONU can select their wavelengths by dynamically changing their locally-oscillated light frequencies Furthermore, coherent WDM-PON uses passive technology to resolve the issue of power budget Coherent WDM-PON directly applies the optical coherent transport technology into the optical access networks This introduces the concern of cost control, which is the design principle of any access technologies Beside, the ONUs in coherent WDM-PON are more complicated that those in other NG-PON2 technologies Such a technology is more in the status of research and lab demo Concerns to cost and complexity challenge its applicability in the access network 4.5 Other Technologies In addition to the NG-PON2 technologies discussed above, some vendors and research institutions proposed other technologies There are: OFDMA PON, tunable hybrid PON, and (O)CDMA PON OFDMA PON implements orthogonal frequency division multiplexing in the electrical spectrum Tunable hybrid PON adopts tunable transmitters and tunable receivers in its terminals (O)CDMA PON distinguishes the communications links between OLT and ONT and implements multiplexing by encoding the electrical domain (CDMA) or optical domain (OCDMA) in the upstream and downstream directions These technologies are off the mainstream as there are serious cost bottlenecks due to technical complexity and immaturity Most of them are under lab research The PON industry does not anticipate fast revolution in the related areas of these technologies, and further research is needed 16 The Evolution of PON Technology and Networks 5.1 Bandwidth Requirement Drives NG PON Evolution As PON technology advances from 1G to 10G and even higher rates, operators are gearing up for a future user bandwidth requirement to 100M and even 1G The mainstream bandwidth requirement is targeted as 100M for residential users and 1G for commercial users in the next 5–10 years The following figure forecasts the bandwidth requirement increase for FTTB/C and FTTH scenarios Figure 5-1 Roadmap of bandwidth requirement for FTTB/C 10G PON Upgraded to 10G GPON Adopt FTTB/C/H Upgrade ADSL2+ to VDSL2 2011: IPTV ratio: 10%, 30% being internet service GPON Per-user bandwidth 2013: IPTV ratio: 40%, 60% being internet service 20M Per-user bandwidth MDU Us BW (24 users) 67.2M 1.07G PON Ds BW DSLAM 50M MDU Us BW (24 users) 187.8M PON Ds BW 3.0G Note: split ratio: 1:16; concurrency: 50%; installation ratio: 75% 2009 2010 2011 2012 2013 10G PON supports a maximum 10G downstream rate, which can accommodate the access requirements of future users On the issue of PON cost, however, 10G PON will cost 3–5 times of GPON in the next 2–3 years Considering the enormous network deployment cost, FTTB/C scenarios are the initial applications of 10G PON, where cost can be shared among more users ONU cost takes up about 60% of the total cost of FTTH equipment Therefore, the large scale deployment of 10G PON in the FTTH scenario depends on the development of the chips and optical components for 10G PON It is anticipated that, in 2015, the cost of 10G PON products will be 17 approximately the same as that of the current GPON products Therefore, by 2015, operators can select 10G PON to increase the bandwidth of residential users to 100M and commercial users to 1G Figure 5-2 Roadmap of rate-rise for FTTH 10G PON Upgraded to 10G GPON High HD service adoption rate 2015: IPTV ratio: 60%, 40% being internet service GPON 2013: IPTV ratio: 40%, 60% being internet service Per-user bandwidth 50M GPON Ds BW (1:128) 1440M Per-user bandwidth 100M 10G GPON Ds BW 1980M (1:128) 2011: IPTV ratio: 10%, 30% being internet service DSLAM 2009 Per-user bandwidth 20M GPON Ds BW (1:128) 867M 2010 2011 2012 Note: concurrency: 50%; installation ratio: 75% 2013 2014 2015 5.2 Industry Chain Drives NG PON Evolution 5.2.1 NG PON Cost Component vendors are at the first stage of the industry chain They develop ASIC chips and optical transceivers only after NG PON standards are released The ASIC chips and optical transceivers are the core of an NG PON system Huawei and other GPON system vendors can provide 10G PON prototypes Huawei fulfilled the world’s first 10G PON demo and field trail The field trail was in a Verizon network Cost of 10G PONs is high Considering a current ONT as an example, the cost distribution of the main components is as follows: Figure 5-3 Cost distribution of the ONT 12% 37% Optics PON Chipset PCB R/C IC 19% 32% 18 Optical components and PON chipset account for over 60% of the total ONT cost Meanwhile, the cost of current 10G PON optical components and chipset are 30–50 times higher than those of GPON's Therefore, large scale application of ONT products relies on cost reduction MDU, which is for FTTB/C, has a different cost distribution in ONT See the following figure Figure 5-4 Cost distribution of the MDU 15% Optics PON Chipset Common part Service card 10% 45% 30% The cost of the optical transceiver and PON chipset of an MDU take up only about 25% of the total cost At the same time, a single FTTB/C MDU usually services over 24 users and the per-user cost is lower The cost of MDU optical components and PON chipsets will be affordable if falling down to 4–6 times of current GPON components With the growth of 10G PON users, 10G PON is estimated to reach a 500k scale in 2013 when the costs will drop to 2-3 times of GPON The following figure shows the estimated data Figure 5-5 Optical component costs (10G PON vs GPON) Multiple 60 50 50 40 30 20 10 4-6 mow 2010 500k 2013 5000k 2015 Scale Year 19 Therefore, it is anticipated that 10G PON will enter small scale commercial application for FTTB/C in 2013, and large scale commercial application in 2015 5.2.2 OLT Capability 10G PON raises new challenges on the system architecture design and performance of the OLT The backplane of the OLT must evolve smoothly to protect existing investments of operators The per-slot bandwidth of the backplane needs to be increased from the current GE/10GE to 40G/80G This is to address the bandwidth requirements of future optical access The OLT needs to support a larger number of users Considering the example of 10G PON in FTTC, FTTC usually covers 200–300 users, and an OLT system connected to 200–300 FTTC MDUs This means that an OLT will accommodate 40k–90k access users Assuming that each user has four MAC addresses, a single OLT system will need to support 2566–512k MAC addresses 10G PON line cards must be slot compatible with current PON line cards for higher network flexibility In terms of network maintenance and management, the unified network management system (NMS) is required to manage PON ports and 10G PON ports at the same time with higher O&M efficiency and lower O&M expenditure To sum up, large capacities, shared platforms, and unified network management systems will be the trends in 10G PON equipment developments that vendors are striving to fulfill 20 21 Copyright © Huawei Technologies Co., Ltd 2010 All rights reserved No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd Trademark Notice , HUAWEI, and are trademarks or registered trademarks of Huawei Technologies Co., Ltd Other trademarks, product, service and company names mentioned are the property of their respective owners NO WARRANTY THE CONTENTS OF THIS MANUAL ARE PROVIDED “AS IS” EXCEPT AS REQUIRED BY APPLICABLE LAWS, NO WARRANTIES OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE MADE IN RELATION TO THE ACCURACY, RELIABILITY OR CONTENTS OF THIS MANUAL TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO CASE SHALL HUAWEI TECHNOLOGIES CO., LTD BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT, OR CONSEQUENTIAL HUAWEI TECHNOLOGIES CO., LTD Huawei Industrial Base Bantian Longgang Shenzhen 518129, P.R China Tel: +86-755-28780808 Version No.: M3-013030802-20100925-C-1.0 DAMAGES, OR LOST PROFITS, BUSINESS, REVENUE, DATA, GOODWILL OR ANTICIPATED SAVINGS ARISING OUT OF OR IN CONNECTION WITH THE USE OF THIS MANUAL www.huawei.com ... view, the next- generation PONs are divided into two phases: NG -PON1 and NG -PON2 Mid-term upgrades in PON networks are defined as NG -PON1 , while NG -PON2 is a long-term solution in PON evolution. .. (G -PON + video) Logic WDM1r IF GPON ONU (G -PON) Rx OLT (G -PON) Rx Splitter Logic Logic Tx Tx Rx OLT (XG -PON) Rx WDM-X IF XGPON, IF Video ONU (XG -PON + video) Logic IF XGPON IF XGPON ONU (XG -PON) .. .Next- Generation PON Evolution Overview .1 PON Evolution .2 2.1 Basic Principles 2.2 Evolution Path .2 Smooth Evolution Based